ONKYO ND-S1
Contents
1. red rays the remote controller may not work reliably Don t put anything on top of the remote con troller such as a book or magazine because a button may be pressed continuously thereby draining the battery The remote controller may not work reliably if the ND S1 is installed in a rack behind col ored glass doors Keep this in mind when installing The remote controller will not work if there s an obstacle between it and the ND S1 s remote control sensor Replacing the Battery The included remote controller uses a CR2025 type battery Always use with the same type 1 To open the battery compartment press the small hollow and slide open the cover 2 While pressing the tab as shown slide out the old battery 3 Slide the new battery into the compart ment with the posi tive side facing up 4 Slide the cover shut Notes Ifthe remote controller doesn t work reliably try replacing the battery e Ifyou intend not to use the remote controller for a long time remove the battery to pre vent damage from leakage or corrosion An expired battery should be removed as soon as possible to prevent damage from leakage or corrosion e Misuse of lithium batteries may cause a fire or chemical burn Always keep out of reach of children Never disassemble charge heat above 100 C or incinerate CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the s2. 5V 1A 3 5W 250 mA Less than 0 4 W 8 1 16 x 1 3 8 x 6 7 8 inches 205 x 35x175 mm 1 17 Ibs 530 g Optical digital audio output coaxial digital audio output com posite video output USB port RI jack E PC System requirements Windows XP SP2 or later or Windows Vista 1 GHz or faster processor Atleast 512 MB of memory 200 MB of free hard drive space to install iTunes additional free space required to store music and videos DirectX 9 0 compatible graphics adapter Atleast 32 MB of video memory 1024 x 768 or higher display resolution e Internet connection Specifications and appearance are subject to change without notice 15 ONKYO CORPORATION Sales amp Product Planning Div 2 1 Nisshin cho Neyagawa shi OSAKA 572 8540 JAPAN Tel 072 831 8023 Fax 072 831 8163 ONKYO U S A CORPORATION 18 Park Way Upper Saddle River N J 07458 U S A Tel 1 201 785 2600 Fax 1 201 785 2650 _ http Awww us onkyo com ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6 82194 Groebenzell GERMANY Tel 49 8142 4401 0 Fax 49 8142 4401 555 http www eu onkyo com ONKYO EUROPE ELECTRONICS GmbH UK BRANCH The Coach House 81A High Street Marlow Buckinghamshire SL7 1AB UK ONEYO Tel 44 0 1628 473 350 Fax 44 0 1628 401 700 HOMEPAGE ONKYO CHINA LIMITED http www onkyo com Unit 1 amp 12 9 F Tower 1 Ever Gain Plaza 88 Container Port Road Kwai Chung N T HONG KONG Tel 86 852 2429
3. abrasive cloths thinners alcohol or other chem ical solvents because they may damage the fin ish or remove the panel lettering 3 Never Touch this Unit with Wet Hands Never handle this unit or its power cord while your hands are wet or damp If water or any other liq uid gets inside this unit have it checked by your Onkyo dealer 4 Do not use other AC adapters car power adapt ers or battery holders containing regular or rechargeable batteries as they may damage the product For U S models FCC Information for User CAUTION The user changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equip ment NOTE This equipment has been tested and found to com ply with the limits for a Class B digital device pursu ant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interfe
4. cally and you ll have to start iTunes manually Note Follow the steps below if you want to cancel sync Failure to follow these steps may result in data loss or malfunction 1 In iTunes click the Eject button to eject your iPod 2 Press and hold the SYNC UNSYNC but ton for at least 2 seconds After a few moments the SYNC UNSYNC indicator flashes indi cating sync has been cancelled 12 E iTunes Restore Function If Tunes detects any damaged data on your iPod it will attempt to restore it When the restore process is complete the ND S1 s sync function may cancel automatically in which case you ll need to press the SYNC UNSYNC button again to sync The following operating systems are sup ported Windows XP Windows Vista iTunes is a trademark of Apple Inc registered in the U S and other countries Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Playing the Music on Your PC Through the ND S1 By connecting the ND S1 to a USB port on your PC you can play the music stored on your PC through your Onkyo audio system 1 Using the included USB cable connect the ND S1 s USB port to a USB port on your PC 2 Press the ND S1 s PC button or the iPod PC button on the included remote controller to select PC The PC indicator lights up green Remote controller PC butto
5. Make sure your iPod is seated properly on the dock connector To prevent dock connector damage don t twist your iPod when inserting or removing it and be careful not to knock your iPod while it s inserted Don t use your iPod with any other accesso ries such as FM transmitters and micro phones because they may cause a malfunction E Removing the iPod Adapter To remove the iPod adapter from the ND S1 insert a small flathead screwdriver into the slot and lift it out as shown below Playing the Music and Videos on Your iPod Music and Video Playback 1 On your iPod select the song or video you want to play 2 Insert your iPod into the ND S1 see page 9 3 Press the remote controller s Play Pause gt 8 button or the ND S1 s iPod button to start playback See below for additional remote controller operation and system functions Remote Controller Button Operation You can use the following buttons to control your iPod Actual operation may vary depend ing on your iPod model its generation and firmware version Aa ON STANDBY SYNC iPod PC UNSYNC i ge yO 6 PLAYLIST ALBUM OO O SHUFFLE REPEAT ONKYO RC 755E w ON STANDBY button Sets the ND S1 to On or Standby iPod PC button Press repeatedly to select your iPod or PC Previous Next lt gt gt buttons During playback or while playback is paused
6. cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or mois ture does not operate normally or has been dropped 14 Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power supply cord or plug is dam aged B If liquid has been spilled or objects have fallen into the apparatus C If the apparatus has been exposed to rain or water D If the apparatus does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation E If the apparatus has been dropped or dam aged in any way and F When the apparatus exhibits a distinct change in performance this indicates a need for service Precautions 1 Recording Copyright Unless it s for personal use only recording copyrighted material is ille gal without the permission of the copyright holder 2 Care Occasionally you should dust the unit all over with a soft cloth For stubborn stains use a soft cloth dampened with a weak solution of mild detergent and water Dry the unit immedi ately afterwards with a clean cloth Don t use
7. nano 4th generation iPod touch 2nd generation iPod Models with Limited Support iPod nano e iPod 5th generation jPod is a trademark of Apple Inc registered in the U S and other countries Made for iPod means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Notes e On the 5th generation iPod and iPod nano the click wheel is disabled during playback Use the ND S1 s iPod button to start and stop playback and the remote controller to control other iPod functions Before using the ND S1 update your iPod with the latest software available from the Apple Web site at www apple com The instructions in this manual apply to iPod models as of June 2009 and may change with future upgrades to the iPod software Several generations of some iPod models have been sold An iPod without xxx gen eration in its name indicates the first gen eration of that particular iPod The AC adapter supplied with the ND S1 is designed exclusively for use with the ND S1 Do not use it with any another device Likewise do not use any other AC adapter with the ND S1 Doing so may damage the ND S1 Supplied Accessories Make sure you have the following accessories AC
8. the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Important Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instruc tions NOM BWDN 8 Do not install near any heat sources such as radi ators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polar ized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the pro vided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Unplug this apparatus during lightning storms or when unused for long periods of time 13 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power sup ply
9. 3118 Fax 86 852 2428 9039 http www ch onkyo com 10908 1 C Copyright 2009 ONKYO CORPORATION Japan All rights reserved 2 9400153
10. ONKYO Digital Media Transport ND S1 Instruction Manual USB Thank you for purchasing an Onkyo product Please read this manual carefully before making any con nections or using this product By following these instructions you ll get the best audio performance and the most listening pleasure from your Onkyo product Keep this manual for future reference Enl Important Safety Instructions 2 Precautions esssssossssessssossssesss 3 Supplied Accessories Getting to Know the ND S1 6 Connecting the ND S1 Playing the Music and Videos on Your iPod oo oc5 ccccoccaccecaccosseosse 10 Playing the Music on Your PC Through the ND S1 Troubleshooting 14 WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING AVIS RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE DO NOT OPEN NE PAS OUVRIR The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons 4 The exclamation point within an equilateral triangle is intended to alert the user to
11. adapter Optical audio cable Video cable Rl cable es Instruction Manual In catalogs and on packaging the letter at the end of the product name indicates the color Specifica tions and operations are the same regardless of color Getting to Know the ND S1 Front and Top ON STANDBY button Sets the ND S1 to On or Standby Remote control sensor Receives control signals from the remote controller STANDBY indicator Lights up when the ND S1 is on Standby If your iPod is charging during Standby it flashes slowly iPod dock connector Connects to your iPod iPod button indicator Press this button to use your iPod Press repeatedly to start and stop iPod playback The indicator lights up blue when your iPod is selected PC button indicator With the ND S1 connected to your PC via USB press this button to output the music stored on your PC digitally from the ND S1 The indicator lights up green when your PC is selected SYNC UNSYNC button indicator With the ND S1 connected to your PC via USB and your iPod inserted in the ND S1 press this button to sync your iPod with your iTunes music library on your PC The indica tor lights up red while sync is in progress To cancel sync press and hold this button for at least 2 seconds The indicator will flash for a few moments and stop flashing when sync has been cancelled While the indicator is flashing you cannot operate any butt
12. ame or equiv alent type Connecting the ND S1 Connecting an Amp or AV Receiver Connect the ND S1 to a digital audio input on your Onkyo amp or AV receiver that can be assigned to an input selector whose Input Dis play can be set to DOCK Setup varies depending on your particular amp or AV receiver model Refer to the Digital Input Setup and Changing the Display sections of youramp or AV receiver s instruction manual for details PC TV 2 Optical digital audio cable fA I cable T AC adapter DIGITAL IN y i i i OPTICAL i 1 zz iS TE TROL AV receiver 1 Using the included optical audio cable connect the ND S1 s OPTICAL AUDIO OUT jack to an optical digital audio input jack on your amp or AV receiver 2 If your iPod supports TV out use the included video cable to connect the ND S1 s VIDEO OUT jack to a composite video input on your TV or AV receiver 3 Using the included RI cable connect the ND S1 s RI REMOTE CONTROL jack to an RI jack on your amp or AV receiver 4 Connect the included AC adapter to the ND S1 s DC IN 5V 1A jack and plug the AC adapter into a suitable wall outlet Notes The ND S1 s audio outputs are digital out puts If the digital audio input on your amp or AV receiver cannot be assigned to an input selector wh
13. cal or coaxial E The built in USB audio interface allows you to output the music stored on your PC digitally optical or coaxial E Music stored on your PC can be output dig itally even when the ND S1 is powered by only the USB bus E Easily sync your iPod with your iTunes music library on your PC E If your iPod supports TV out connecting the ND S1 s VIDEO jack to your TV or AV receiver allows to you to enjoy videos E in addition to the included remote control ler you can also use your Onkyo amp or AV receiver s remote controller E The ND S1 charges your iPod while you enjoy your music 1 When powered by only the USB bus some iPod functionality is not available and your iPod will not be charged so always use the included AC adapter when possible 2 Only IR I capable Onkyo amp and AV receiver remote controllers are supported If the remote controller supplied with your Onkyo amp or AV receiver has separate POWER ON and STANDBY buttons operation is as follows When the amp or AV receiver is set to Standby only the amp or AV receiver turns On When the amp or AV receiver is already On the ND S1 turns On So to turn on the ND S1 when the amp or AV receiver is set to Standby on the remote controller supplied with your amp or AV receiver you must press the ON button twice Recommended iPod Models iPod nano 2nd generation iPod nano 3rd generation e iPod classic iPod touch iPod
14. n iPod PC button 3 Start music playback on your PC Use your amp or AV receiver s volume con trol to adjust the playback volume Note Ifthe ND S1 is not recognized as a USB audio device even after restarting your PC in the Control Panel open Sounds amp Audio Devices and select USB Audio DAC as the default sound playback device For more information see the Sound Troubleshooter in Windows Help 13 Troubleshooting 14 No Sound or Video Make sure your iPod is connected properly If there s no video make sure you iPod sup ports TV out Make sure your iPod is playing Make sure your amp or AV receiver is turned on the input to which the ND S1 is con nected is selected as the input source and the volume control is not set to minimum Make sure all plugs are pushed in all the way Make sure the ND S1 is connected to the cor rect input jacks on your amp or AV receiver If there s no video check your video connec tions Do not connect the ND S1 to any jacks on your amp or AV receiver labeled OUT Make sure the AC adapter is properly con nected to the ND S1 and a suitable wall out let Try resetting your iPod If you remove then re insert your iPod it may not be recognized temporarily In this case press and hold down the ND S1 s iPod but ton for at least 2 seconds to reset the ND S1 If it s still not recognized disconnect the USB cable and AC adapter then reconnect
15. ons or start iPod playback See page 12 for details Rear Panel R1 REMOTE CONTROL jack Connects to the FRI jack on another RI capable Onkyo component for linked oper ation This connection should not be used with some components See page 8 for details OPTICAL AUDIO OUT jack This optical digital audio output jack con nects to an optical digital audio input ona system component amp or AV receiver COAXIAL AUDIO OUT jack This coaxial digital audio output jack con nects to a coaxial digital audio input on a system component amp or AV receiver USB port Connects to a USB port on your PC for play ing music stored on your PC and iTunes sync VIDEO OUT jack Connects to a composite video input on your TV or AV receiver for video playback DCIN 5V 1A jack Connect the included AC adapter here Using the Remote Controller Aiming the Remote Controller E Remove the battery protect tab before use Point the included remote controller toward the ND S1 s remote control sensor as shown Remote control sensor ND S1 Notes The remote controller may not work reliably if the ND S1 is subjected to bright light such as direct sunlight or inverter type fluores cent lights Keep this in mind when installing Ifanother remote controller of the same type is used in the same room or the ND S1 is installed close to equipment that uses infra
16. ose Input Display can be set to DOCK do not connect the RI cable other wise a malfunction may occur Do not place the ND S1 on top of a compo nent that gets warm or one with has air vents on top as it may interfere with that compo nent s cooling or cause the component or ND S1 to overheat Place it next to the com ponent use an audio rack etc Inserting Your iPod into the ND S1 Prepare the adapter that came with your iPod 1 Gently push down and slide open the dock cover on the ND S1 2 Insert the adapter supplied with your iPod then push your iPod firmly onto the ND S1 s dock connector Adapter supplied with iPod Notes If you use a case with your iPod always remove it before you insert it Otherwise it may not connect properly and a malfunction may occur Do not insert your iPod into the ND S1 with out the adapter that came with it as it may put unnecessary strain on the iPod or ND S1 s dock connector causing permanent damage When you insert your iPod the ND S1 works as follows depending on the status of your iPod iPod not playing The ND S1 starts charging your iPod and the STANDBY indicator flashes slowly iPod playing The ND S1 turns on the iPod indicator lights up blue and your iPod continues play ing Notes If the iPod indicator does not light up after you ve inserted your iPod this means that your iPod is not properly seated on the dock connector
17. press the Next gt button to 10 select the next song Press the Previous 4 button to return to the beginning of the cur rent song press again to select previous songs Press and hold to fast forward or rewind Play Pause gt 11 button Press to start playback on your iPod Your iPod will turn on automatically if it s not already on Press the button again to pause playback PLAYLIST Up Down buttons If your iPod contains playlists press the PLAYLIST Up N button to select the previ ous playlist Press the PLAYLIST Down M button to select the next playlist on your iPod SHUFFLE button Press repeatedly to set the shuffle function on your iPod Song Album or Off SYNC UNSYNC button Press to start or cancel iPod sync The indica tor shows the current status ALBUM Up Down buttons Used to change albums To change album start album or all song playback then press the ALBUM Up Down N M buttons REPEAT button Press repeatedly to set the repeat function on your iPod One All or Off Some of the iPod functions that you can control with this remote controller can also be con trolled with the remote controller that came with your amp or AV receiver Refer to the instruction manual that came with your amp or AV receiver for details see pages 8 to 9 for connection information System Functions You can use the following system functions E System On When you t
18. rence by one or more of the fol lowing measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is con nected Consult the dealer or an experienced radio TV technician for help For Canadian Models NOTE THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES 003 Mod le canadien REMARQUE CET APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME ALA NORME NMB 003 DU CANADA For some models Before use connect the appropriate AC plug adapter to the AC adapter The type of plug adapter depends on the place of purchase lt RY Disconnect 4 Connect For European Models Declaration of Conformity We ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6 82194 GROEBENZELL GERMANY declare in own responsibility that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065 EN55013 EN55020 and EN61000 3 2 3 3 GROEBENZELL GERMANY K MIYAGI ONKYO EUROPE ELECTRONICS GmbH Features E With the Onkyo ND S1 Digital Media Transport you can easily play the music stored on your iPod through your Onkyo audio system and enjoy great sound E The ND S1 processes the digital audio sig nal directly from your iPod for high quality digital audio output opti
19. the specified time and select your iPod as the input source automatically Notes e Linked operations do not work with video playback or when the alarm is set to play a sound e If you use your iPod with any other accesso ries iPod playback detection may not work E Operating Notes e Use your amp or AV receiver s volume con trol to adjust the playback volume e While your iPod is inserted in the ND S1 its volume control has no effect e Ifyoudo adjust the volume control on your iPod while it s inserted in the ND S1 be careful that it s not set too loud before you reconnect your earphones Note e On the 5th generation iPod and iPod nano the click wheel is disabled during playback Use the ND S1 s iPod button to start and stop playback and the remote controller to control other iPod functions 11 Syncing Your iPod to Your PC You can transfer songs and videos from your iTunes music library on your PC to your iPod by using sync Videos are restricted to iPod mod els that support video 1 Using the included USB cable connect the ND S1 s USB port to a USB port on your PC 2 Press the SYNC UNSYNC button The indicator lights up red iTunes opens on your PC and sync starts Remote controller SYNC UNSYNC button SYNC UNSYNC button Note Inthe iTunes settings if the Automatically sync when this iPod is connected option is not selected iTunes will not open automati
20. them Remote Controller doesn t work Make sure your iPod is seated properly on the dock connector If your iPod is in a case it may not connect properly so always remove the case before inserting your iPod into the ND S1 Your iPod cannot be controlled while it s dis playing the Apple logo If your remote controller has Remote Mode buttons make sure the mode necessary to control your iPod is selected If you re using the remote controller that came with your amp or AV receiver be sure to point it toward your amp or AV receiver when you want to control your iPod An RI cable connection is required with some components but not others If you connect it by mistake remote control may not work See page 8 for details Try resetting your iPod Others Before using one of the other components connected to your amp or AV receiver stop playback on your iPod If playback is not stopped the Direct Change function may select your iPod as the input source by mis take at the transition between songs Depending on the backlight setting on your iPod the display may become dim during use If the display is hard to see change the backlight setting on your iPod Do not use Cover Flow while playing music on your iPod as it may stop iPod playback or cause noise Specifications Power supply Power consumption USB consumption Standby consumption Dimensions W x Hx D Weight Jacks 100 240 V AC adapter
21. urn on your amp or AV receiver the ND S1 and iPod turn on automatically In addi tion when the ND S1 and iPod are on some amps and AV receivers can be turned on by pressing the ON STANDBY button E System Off When you turn off your amp or AV receiver the ND S1 and iPod automatically go on Standby E Timer Off If you set your amp or AV receiver s sleep timer the ND S1 and iPod will automatically switch to Standby at the specified sleep time E Timer Play If you set your amp or AV receiver s play timer the ND S1 and iPod will automatically turn on and your iPod will start playback at the speci fied time E Auto Power On If you press the remote controller s Play Pause gt 8 button while your amp or AV receiver is on Standby your amp or AV receiver will turn on automatically select your iPod as the input source and your iPod will start playback E Direct Change if you start iPod playback while listening to another input source your amp or AV receiver will automatically switch to the input to which the ND S1 is connected E Other Remote Controllers You can use the remote controller that came with your amp or AV receiver to control other iPod functions The available functionality depends on your amp or AV receiver See the instruction manual that came with your amp or AV receiver for details E iPod Alarm If you use the Alarm function on your iPod to start playback your amp or AV receiver will turn on at
Download Pdf Manuals
Related Search