Home

Edimax 3G-6200n 11n Wireless 3G Broadband Router

1. Username Password Idle Timeout 0 Echo Timeout 60 Echo Count 3 Network Settings User Name Optional Password Optional APN internet Senice 36 3 56 Only UMTS HSPA HSDPA v 28 Step 3 Broadband Type Connect to Internet via Ethernet 3G 6200n provides two types of Internet connection method wireless 3G 3 5G or wired connection You can access internet via USB 3G 3 5G modem card or via wired xDSL cable modem connection However only one connection method wireless or wired can be used at the same time In this section you have to select one of six types of connections that you will be using to connect your broadband router s WAN port to your ISP see screen below Note Different ISP s require different methods of connecting to the Internet please check with your ISP as to the type of connection it requires O 3G 3 5G If you connect to Internet using an 3G 9 5G handset or 36 3 56G USB modem then you should choose this option and enter the required information Cable Modem A connection through a cable modem requires minimal configuration When you set up an account with your Cable provider the Cable provider and your Wireless Router will automatically establish a connection so you probably do not need to enter anything more O Fixed IP xDSL Some xDSL Internet Service Providers may assign a Fixed IP Address for your Wireless Router If you ha
2. 2 DI NETWORKING PEOPLE TOGETHER nLite Wireless 3G Broadband Router 3G 6200n User Manual Version 1 0 3 2009 EDIMAX NETWORKING PEOPLE TOGETHER Copyright by Edimax Technology Co LTD all rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of this company This company makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Any software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not this company its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software Further this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes Notice according to GNU GPL Version 2 This product includes software that is subject to the GNU GPL Version 2 You find the text of the license on the product cd dvd Th
3. SIM and input the PIN code provided by telecomm service provider Most of options listed here are optional and you don t have to provide those information if telecomm service provider doesn t provide you with those information If telecomm provider provides you with username password please check User Name Password box and input the user name password provided by telecomm service provider then click OK button Wait for 1 minute for 3G 6200n to reboot then you can access Internet O 3G6 3 5G If you connect to Internet using an 3G 3 5G handset or 3G 3 5G USB modem then you should choose this option and enter the required information O Cable Modem A connection through a cable modern requires minimal configuration When you set up an account with your Cable provider the Cable provider and your Wireless Router will automatically establish a connection so you probably do not need to enter anything more O Fixed IP xDSL Some xDSL Internet Service Providers may assign a Fixed IP Address for your Wireless Router If you have been Please input User name amp Password in PPP Settings and do not input them in Network Settings unless your ISP ask you input them in both PPP Settings Username Password Idle Timeout 0 Echo Timeout 60 Echo Count 3 Network Settings User Name Optional Password Optional Enter PIN Code APN i
4. Static Routing You can enable Static Routing to turn off NAT function of this router and let this router forward packets by your routin policy Cl Enable Static Routing Destination LAN IP Subnet Mask Default Gateway LAN Current Static Routing Table NO Destination LANIP Subnet Mask Default Gateway Hop Count Interface Select APPLY CANCEL Parameters Description Static routing function is disabled by default You have to enable the static routing function to make your routing rules take effect Enable Static Routing Destination The network address of destination LAN LAN IP Subnet Mask The subnet mask of destination LAN Default The next stop gateway of the path toward the 83 Gateway destination LAN This is the IP of the neighbor router that this router should communicate with on the path to the destination LAN Hop Count The number of hops routers to pass through to reach the destination LAN Interface The interface that go to the next hop router Add a Rule Fill in the Destination LAN IP Subnet Mask Default Gateway Hop Count and Interface of the rule to be added and click Add Then this static routing rule will be added to the Static Routing Table listed below If you found any typo before adding it and want to correct it just click Reset and the fields w
5. This page lists all DHCP clients Active DHCP Client 2 This table shows the assigned IP address MAC address and time expired for each DHCP leased client IP Address MAC Address Time Expired Second 192 168 2 100 00 00 00 00 00 00 3547 192 168 2 101 00 13 02 5f ed e9 forever Parameters Description This page shows all DHCP clients currently connected Active DHCP to your network The Active DHCP Client Table Client displays the IP address and the MAC address and expiry time of each LAN Client Use the Refresh button to get the most updated information 101 3 6 Statistics View the statistics of packets sent and received on WAN LAN and Wireless LAN interface Statistics 2 This page shows the packet counters for transmission and reception regarding to networks Packets Sent 107 Packets Received 5706 Packets Sent 302 Packets Received 195 Packets Sent 124 Packets Received 514 Wireless LAN Ethernet LAN Parameters Description Statistics Shows the statistics of packets sent and received on WAN LAN and Wireless LAN interface 102 Chapter 4 Tool This page includes basic configuration tools of this broadband router such as Configuration Tools save or restore configuration settings Firmware Upgrade upgrade system firmware and Reset Tools mee The Tools Settings section includes the basic configuration tools such as Save Restore Configuration Settings and
6. fMAIAIAE Default Gateway User Name Password ASA EA 0 0 0 0 Connection ID Optional 1392 512 lt MTU lt 1492 ATINA Enable For BEZEQ network in ISRAEL use only AEREA A Continuous v onnect Disconnect TAGATA 10 4 100 Minute BACK iligi z 5 5 Y w 2 2 Y Parameter Description The ISP requires you to obtain an IP address by del DHCP automatically before connecting to the PPTP server Use the following The ISP gave you a static IP to be used to connect IP Address IP address to the PPTP server IP Address This is the IP address that your ISP gave you to establish a PPTP connection Subnet Mask Enter the Subnet Mask provided by your ISP e g 255 255 255 0 Gateway Enter the IP address of the ISP s Gateway Enter the User Name provided by your ISP for the User ID PPTP connection Sometimes called as Connection ID p Enter the Password provided by your ISP for the assword PPTP connection If your LAN has a PPTP gateway then enter that PPTP Gateway PPTP gateway s IP address here If you do not have a PPTP gateway then enter the ISP s Gateway IP address same as above Connection ID This is the ID given by your ISP and this is optional BEZEQ ISRAE Select this item if you are using the service provided by BEZEQ in Israel Connection Type If you select Continuous the router
7. to save changes you made and restart the broadband router this requires about 30 seconds and the broadband router will stop responding this is normal and is not malfunction You can reconnect to this broadband router and continue on other settings later 2 8 2 URL Blocking If you want to prevent computers in local network from accessing certain website like pornography violence or anything you want to block you can use this function to stop computers in local network from accessing the site you defined here This function is useful for parents and company managers Please follow the following instructions to set URL blocking parameters Please click Firewall menu on the left of web management interface then click URL Blocking and the following message will be displayed on your web browser URL Blocking You can block access to certain Web sites from a particular PC by entering either a full URL address or just a keyword of the Web site C Enable URL Blocking URLKeyword A E Current URL Blocking Table IT seee Delete Selected Delete Al Parameters Description Enable URL Enable disable URL Blocking Blocking 91 Add URL Keyword Fill in URL Keyword and then click Add You can enter the full URL address or the keyword of the web site you want to block If you found any typo before adding it and want to correct it just click Reset and the
8. The Network window will appear 3 Check your list of Network Components If TCP IP is not installed click the Add button to install it if TCP IP is installed jump to step 6 4 In the Network Component Type dialog box select Protocol and click Add button 5 In the Select Network Protocol dialog box select Microsoft and TCPAP and then click the OK button to start installing the TCP IP protocol You may need your Windows installation CD to complete the installation 6 After installing TCP IP go back to the Network dialog box Select TCP IP from the list of Network Components and then click the Properties button 7 Check each of the tabs and verify the following settings 10 eGateway All fields are blank eDNS Configuration Select Disable DNS eWINS Configuration Select Disable WINS Resolution elP Address Select Obtain IP address automatically TCP IP Properties x Bindings Advanced Netblos DNS Configuration Gateway WINS Configuration IP Address n P address can be automatically assigned to this computer If pour network does not automatically assign IP addresses ask your network administrator for an address and then type it in the space below Specify an IP address CITI CITI 8 Reboot the PC Your PC will now obtain an IP address automatically from your Broadband Router s DHCP server Note Please make sure that the Broadband router is the only DHCP server on your LAN Once you ve configured
9. configuration request Enrollee This broadband router will act as WPS enrollee and send WPS configuration request to other WPS registrar Configure via Push Click Start PBC to start Push Button type WPS Button configuration PBC Please push the WPS push button on other WPS compatible network devices to begin WPS configuration You can also push the WPS Reset button located at the back of this broadband router to start PBC without using web configuration interface Configure via Please input the PinCode displayed at the configuration Client PinCode software of WPS enabled wireless client and click Start PIN to establish connection with the wireless client 68 2 6 QoS The QoS function can classify Internet application traffic by source destination IP address and port number You can assign priority for each type of application and reserve bandwidth for it The packets of applications with higher priority will always go first Lower priority applications will get bandwidth after higher priority applications get enough bandwidth This can let you have a better experience in using delay sensitive services like Internet phone video conference etc All the applications not specified by you are classified as rule name Others The rule with smaller priority number has higher priority the rule with larger priority number has lower priority You can adjust the priority of the rules by moving the
10. e _ Remember my password rma 6 The HOME page screen below will appear The Home Page is divided into four sections Quick Setup Wizard General Setup Status Info and System Tools EDI NETWORKING PEOPLE TOGETHER General Setup The Wireless Router supports advanced functions like Virtual Server Access Control Hacker Attack Detection and DMZ We highly recommend you keep the default settings Quick Setup Wizard Chapter 1 Select your Internet connection type and setup the configurations needed to connect to your Internet Service Provider ISP General Setup Chapter 2 This section contains configurations for the Broadband router s advanced functions such as address mapping virtual server access control hacker attack prevention DMZ special applications and other functions to meet your needs Status Info Chapter 3 In this section you can see the Broadband router s system information Internet Connection Device Status System Log Security Log and DHCP client information System Tools Chapter 4 This section contains the broadband router s tool sets tools include configuration firmware upgrade and Reset Configuration tools allow you to backup save restore or restore to factory default configuration for your Broadband router The firmware upgrade tool allows you to upgrade your Broadband router s firmware The RESET tool allows you to reset your Broadband router 7 Click on Quick
11. 2 this device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment Federal Communication Commission Radiation Exposure Statement This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person s body excluding extremities of hands wrist and feet during wireless modes of operation The equipment version marketed in US is restricted to usage of the channels 1 11 only R amp TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999 5 EC 114 OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity R amp TTE The R TTE Directive repeals and replaces in the directive 98 13 EEC Telecommunications Terminal Equipment and Satellite Earth Station Equipment As of April 8 2000 Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment All guidelines of this and of the computer manufacture must therefore be allowed at all times
12. All existing special application mappings will be displayed in this page To delete one or more mappings check the box of the mapping then click Delete Selected button to remove the mapping To delete all existing mappings click Delete All button If you want to uncheck all boxes click Reset 79 When you finished with the settings in this page you can click Apply button to save changes you made in this page or you can click Cancel to discard changes After you click Apply button you ll see the following messages Save setting successfully Please press APPLY button to restart the systern for changes to take effect Apply Please click Apply to save changes you made and restart the broadband router this requires about 30 seconds and the broadband router will stop responding this is normal and is not malfunction You can reconnect to this broadband router and continue on other settings later 80 2 7 4 UPnP Settings With UPnP all PCs in you Intranet will discover this router automatically So you do not have to do any configuration for your PC and they can access the Internet through this router automatically UPnP UPnP is more just a simple extension of the Plug and Play peripheral model Itis designed to support zero configuration invisible networking and automatic discovery for a breadth of device categories from a wide range of vendors With UPnP a device can dynamically
13. D Ego Data E _ Devices with Removable Storage My Network Places My Documents E Shared Documents GB Control Panel Details My Computer System Folder JO 3 Floppy A o CD Drive F E ba o BandLuxe C1005 G 4 My Compu 5 The program inside the adapter will prepare to install the driver and utility of the adapter InstallShield Wizard Preparing to Install 4 BandLuxe HSDPA Utility R1 Setup is preparing the InstallShield WWizard which will guide you through the program setup process Please wait Configuring Windows Installer 22 6 Click Next ie BandLuxe HSDPA Utility R1 InstallShield Wizard Welcome to the InstallShield Wizard for BandLuxe HSDPA Utility R1 The InstallShield R Wizard will install BandLuxe HSDPA Utility Ri on your computer To continue click Next WARNING This program is protected by copyright law and international treaties 7 Select I accept the terms in the license agreement and click Next i BandLuxe HSDPA Utility R1 InstallShield Wizard License Agreement Please read the Following license agreement carefully End User License Agreement IMPORTANT READ CAREFULLY BandRich Inc BANDRICH licenses the enclosed software associated materials and onlinefelectronic documentation Product to you upon the terms contained in this EULA Please read the terms carefully before using this softwar
14. DNS server that you would rather use you need to specify the IP address of that DNS server here A DNS Domain Name System server is like an index of IP Addresses and Web Addresses lf you type a Web address into your browser such as www broadbandrouter com a DNS server will find that name in its index and find the matching IP address Most ISPs provide a DNS server for speed and convenience Since your Service Provider may connect you to the Internet through dynamic IP settings it is likely that the DNS server IP Address is also provided dynamically However if there is a DNS server that you would rather use you need to specify the IP Address of that DNS server The primary DNS will be used for domain name access first in case the primary DNS access failures the secondary DNS will be used Primary DNS Secondary DNS APPLY CANCEL Parameters Description Fill in the ISP s DNS server IP address or you can DNS address specify your own preferred DNS server IP address Secondary DNS This is optional You can enter another DNS Address server s IP address as a backup The secondary optional DNS will be used when the above DNS fail Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router with the advanced settings in place 2 3 8 DDNS DDNS allows you to map the static domain name to a dynamic IP ad
15. Finish to exit the wizard 25 12 The utility of C100S will start up automaticity Please select the MENU 13 Click Setting Language English United States 1 26 15 Plug in the C100S into the USB port of the 3G router 16 The USB adapter will get the IP address from ISP automatically You can check the Status of the 3G 6200n on the Web site ex 192 168 2 1 EDIMAX METWORIONO PEOPLE TOGETAEA nternet Connection 2 View the current internet connection status and related 3 2 3 2 53 3 AI Dynamic IP disconnect IP address 10 64 64 68 PTE ES 000 264469 CA 210 241 192 201 168 95 1 1 Default Gateway Secondary DNS Connected 118 231 54 74 255 255 255 255 10 64 64 68 BandRich Inc 0x1 a8d BandLuxe 3 5G HSDPA Adapter 0x1002 DOTA 35577601 0450878 17 Now you are able to connect to Internet successfully MSN com Microsoft Internet Explorer File Edit View Favorites Tools Help Qe Q x a CA JO search She Favorites 2 A a 3 http Jfuwww msn comf Make MSN your homepage today U And get the homepage favored by millions View Cheapest Hybrid Sedans Monday June 23 200 Web MSN Images Video N Maps Q tive Search Welcome Sign in Hotmail Air Tickets Travel Election 2008 Lifestyle News Tech amp Gadgets im Messenger Autos Games Maps amp Directions Real Estate Rentals TV REN Careers amp Jobs Green Money
16. Password Confirm Password APPLY CANCEL Parameters Description Enter your current password for the remote Current management administrator to login to your Password Broadband router Note By default there is NO password New Password Enter your new password Enter your new password again for verification purposes Confirmed Note If you forget your password you ll have to Password reset the router to the factory default No password with the reset button see router s back panel Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 44 2 1 3 Remote Management The remote management function allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site Enter the designated host IP Address in the Host IP Address field Remote Management 2 The remote management function allows you to designate a host in the Internet to have management confiquration access to the Wireless Router from a remote site Enter the designated host IP Address in the Host IP Address field T APPLY CANCEL Parameters Description Host Address This is the IP address of the host in the Internet that will have management configuration access to the Broadband router from a remote site This means if you are at home and your home
17. Port 1723 O VPN L2TP UDP Port 1701 O TCP All TCP Port mo UDP All UDP Pot O You can select multiple services here If you wish to deny or allow all services of certain IP address es please select both TCP and UDP If the service you wish to deny or allow is not listed you can use User Define 89 Service table to add a new service of your own User Define Service Protocol Port Range Here are descriptions of every setup items Item Name Description Protocol Please select the protocol type of this service TCP or UDP or Both Port Range Please input the port range if this service For a single port number just input the number of service port like 110 If this service consists multiple continuous ports you can input 110 120 for port number 110 to 120 or 110 115 120 for port number 110 115 and 120 Click Add to add this IP address restriction rule to the list and back to previous page or click Reset to clear all texts in every field When you finished with the settings in this page you can click Apply button to save changes you made in this page or you can click Cancel to discard changes After you click Apply button you ll see the following messages Save setting successfully Please press APPLY button to restart the systern for changes to take effect Apply Please click Apply
18. Setup Wizard see chapter 1 to start configuring settings required by your ISP so that you can start accessing the Internet The other sections General Setup Status Information and Tools do not need to be configured unless you wish to implement monitor more advanced features information Select the section Quick Setup Wizard General Setup Status Information and Tools you wish to configure and proceed to the corresponding chapter Chapter 1 Quick Setup The Quick Setup section is designed to get you using the broadband router as quickly as possible In the Quick Setup you are required to fill in only the information necessary to access the Internet Once you click on the Quick Setup Wizard in the HOME page you should see the screen below Step 1 Time Zone The Time Zone allows your router to base its time on the settings configured here this will affect functions such as log entries and firewall settings Time Zone 2 Set the time zone of the Wireless Router This information is used for log entries and firewall settings GMT 00 00 Greenwich Mean Time Dublin Edinburgh Lisbon London MILE OR SCA 1192 43 244 18 b Daylight Savings ClEna la Time From To NEXT Parameter Description Select the time zone of the country you are living The router will set its time based on your selection Set Time Zone Time Server You can manually assign time server address if the Address default time serve
19. The Status and Information section allows you to view the router s system information Status 2 The Wireless Router s status information provides the following information about your Wireless Router Hardware Firmware version Serial Number and its current operating status System DIES ac 52008 wireless 36 Router Oday 0h 0m 33s Parameters Description You can see the router s system information such as the router s LAN MAC address WAN MAC address Information hardware version serial number boot code version runtime code version 96 3 1 Internet Connection View the Broadband router s current Internet connection status and other related information View the current internet connection status and related information Attain IP Protocol Default Gateway Secondary DNS Dynamic IP disconnect IP Address Subnet Mask 192 168 9 254 RSU 00 1F 1F 1F 74 51 tute AIL eee 192 168 1 2 192 168 1 12 uel SES Disconnected IP Address N A TEA NA Gateway N A Ei cee NA N A Parameters Description This page displays the router s WAN port and ternet 3G 3 5G Internet WWAN connection information Connection including WAN IP address subnet mask and ISP gateway as well as the primary DNS and secondary DNS being used 97 3 2 Device Status View the broadband router s current configuration settings The device status displays the configuration settings yo
20. This page allows you to change the setting for WPS Wi Fi Protected Setup WPS can help your wireless client automatically connect to the Wireless Router Enable WPS C Enable WPS Proxy WPS Information Wie eles Configured ATREA 20613921 E AAA WPA pre shared key Passphrase Key e Device Configure Config Mode Configure by Push Button Start PBC Configure by Client PinCode Start PIN Here are descriptions of every setup items Item Name Description Enable WPS Check this box to enable WPS function uncheck it to disable WPS WPS Status If the wireless security encryption function of this wireless router is properly set you ll see Configured message here If wireless security function has not been set you ll see unConfigured Self PIN code This is the WPS PIN code of this wireless router This code is useful when you need to build wireless connection by WPS with other WPS enabled wireless 67 devices SSID The SSID of this wireless router will be displayed here Authentication The wireless security authentication mode of this Mode wireless router will be displayed here Passphrase Key The WPA passphrase will be displayed as asterisk here Config Mode Select the WPS configuration role of this broadband router Registrar This broadband router will act as WPS registrar and wait for wireless clients to send WPS
21. allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network WPA Unicast Cipher Suite RADIUS Server IP Address WPA RADIUS he COWPA TKIP OWPA2 AES OWPA2 Mixed 1812 RADIUS Server Port RADIUS Server Password APPLY CANCEL Parameters Description WPA TKIP TKIP will change the encryption key frequently to enhance the wireless LAN security WPA2 AES uses CCMP protocol to change encryption WPA2 AES key frequently AES can provide high level encryption to enhance the wireless LAN security WPA2 MIXED will use TKIP or AES based on the other communication peer automatically RADIUS The IP address of external RADIUS server Server IP address RADIUS The service port of the external RADIUS server Server Port RADIUS The password used by external RADIUS server Server Password WPA2 Mixed Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 2 5 4 Access Control This wireless router provides MAC Address Control which prevents unauthorized MAC Addresses from accessing your wireless network 65 For security reason the Wireless Router features MAC Address Filtering that only allows authorized MAC Addresses associating to the Wireless Router e MAC Address
22. automatically from your Broadband Router s DHCP server Note Please make sure that the Broadband router is the only DHCP server on your LAN Once you ve configured your PC to obtain an IP address automatically please proceed to Step 3 3 Once you have configured your PCs to obtain an IP address automatically the router s DHCP server will automatically give each of your LAN clients an IP address By default the Broadband Router s DHCP server is enabled so that you can obtain an IP address automatically To see if you have obtained an IP address see Appendix A Note Please make sure that the Broadband router s DHCP server is the only DHCP server on your LAN lf there is another DHCP on your network then you ll need to switch one of the DHCP servers off To disable the Broadband router s DHCP server see chapter 2 LAN Port 4 Once your PC has obtained an IP address from your router enter the default IP address 192 168 2 1 broadband router s IP address into your PC s web browser and press lt enter gt 5 The login screen below will appear Enter the User Name and Password and then click lt OK gt to login Note By default the user name is admin and the password is 1234 For security reasons it is recommended that you change the password as soon as possible in General setup system password see chapter 2 Connect to 192 168 2 1 Default admin 1234 User name admin Password
23. f and 0 9 or 13 digit ASCII characters as the encryption keys Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 61 2 5 3 2 802 1x only IEEE 802 1x is an authentication protocol Every user must use a valid account to login to this Access Point before accessing the wireless LAN The authentication is processed by a RADIUS server This mode only authenticates user by IEEE 802 1x but it does not encryption the data during communication This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network Enable 802 1x Authentication RADIUS Server IP Address y RADIUS Server 11812 RADIUS Server Password APPLY CANCEL Parameters Description RADIUS Server IP address The IP address of external RADIUS server RADIUS Server Port The service port of the external RADIUS server RADIUS Server Password The password used by external RADIUS server Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 62 2 5 3 3 802 1x WEP Static key IEEE 802 1x is an authentication protocol Every user must use a valid account to login to this Access Point before accessing the wireles
24. field will be cleared Remove URL Keyword If you want to remove some URL keyword from the Current URL Blocking Table select the URL keyword you want to remove in the table and then click Delete Selected If you want remove all URL keyword from the table just click Delete All button If you want to clear the selection and re select again just click Reset You can now configure other advance sections or start using the router 92 2 8 3 DoS Denial of Service The Broadband router s firewall can block common hacker attacks including Denial of Service Ping of Death Port Scan and Sync Flood If Internet attacks occur the router can log the events Parameters DoS 2 The Wireless Router s firewall can block common hacker attacks including DoS Discard Ping from WAN and Port Scan DoS Module Ping of Death Discard Ping from WAN O O pescan O Sync Flood Advanced Settings APPLY CANCEL Description Ping of Death Protect from Ping of Death attack Discard Ping The router s WAN port will not respond to any Ping From WAN requests Port Scan Protect the router from Port Scan Sync Flood Protect the router from Sync Flood attack Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 93 2 8 4 DMZ If you have a local client PC that cannot run so
25. lt Refresh gt button to get the most updated information When the system is powered down the system log will disappear if it s not saved as a local file System Log 99 3 4 Security Log View any attempts that have been made to gain access to your network Security Log View any attempts that have been made to illegally gain access to your network 2000 01 01 00 00 58 start Dynamic IP 2000 01 01 00301301 SNTP connect to TimeServer 192 43 244 18 2006 11 05 06 42 02 SNTP connect success 2006 11 05 06 42 02 SNTP set time to 2008 11 05 06742202 2008 11 05 06 42 02 FIREWALL WAN IP is 192 168 9 177 setting firewall 2008 11 05 06 42 10 DNS dns restart 2008 11 05 08 24 39 start Dynamic IP 2008 11 05 08 24 41 SNTP connect to TimeServer 192 43 244 18 2008 11 05 08 39 38 SNTP connect success Kl _ gt Parameters Description This page shows the current security log of the Broadband router It displays all attempts tried to access your network At the bottom of the page the security log can be Security Log saved lt Save gt as a local file you can clear the log by clicking lt Clear gt too You can also click lt Refresh gt button to get the most updated information When the system is powered down the security log will disappear if it s not saved as a local file 100 3 5 Active DHCP Client
26. private IP address and its service port number See Glossary for an explanation on Port number You can configure the Wireless Router as a Virtual Server so that remote users accessing services such as the Web or FTP at your local site via Public IP Addresses can be automatically redirected to local servers configured with Private IP Addresses In other words depending on the requested service TCP UDP port number the Wireless Router redirects the external service request to the appropriate internal server located at one of your LAN s Pirvate IP Address C Enable Virtual Server lt lt Select Both e Current Virtual Server Table O pamer Pemeran D npe Pateren T Commen Seea APPLY CANCEL Here are descriptions of every setup items Item Name Description Enable Virtual Server Check this box to enable virtual server and uncheck this box to disable virtual server Private IP Input the IP address of the computer which provides Internet service Computer name All computer names found by this broadband router on local network will be listed here You can select the computer name and click lt lt button to add selected computer s IP address to Private IP field 76 Please note that this list may not be able to list all computers on your local network Private Port Input the port number of the IP address which provi
27. the connection will be disconnected automatically IP Address and Network Subnet Mask IP stands for Internet Protocol An IP address consists four sets of numbers separated by periods which identifies a single unique Internet computer host in an IP network Example 192 168 2 1 It consists of 2 portions the IP network address and the host identifier The IP address is a 32 bit binary pattern which can be represented as four cascaded decimal numbers separated by aaa aaa aaa aaa where each aaa can be anything from 000 to 255 or as four cascaded binary numbers separated by bbbbbbb bbbbbbbb bbbbbbbb bbbbbbbb where each b can either be Oor 1 A network mask is also a 32 bit binary pattern and consists of consecutive leading 1 s followed by consecutive trailing 0 s such as 11111111 11111111 11111111 00000000 Therefore sometimes a 109 network mask can also be described simply as x number of leading 1 s When both are represented side by side in their binary forms all bits in the IP address that correspond to 1 s in the network mask become part of the IP network address and the remaining bits correspond to the host ID For example if the IP address for a device is in its binary form 11011001 10110000 10010000 00000111 and if its network mask is 11111111 11111111 11110000 00000000 It means the device s network address is 11011001 10110000 10010000 00000000 and its host ID is 00000000
28. the Internet The General Setup contains advanced features that allow you to configure the router to meet your network s needs such as Wireless Address Mapping Virtual Server Access Control Hacker Attack Prevention Special Applications DMZ and other functions Below is a general description of what advance functions are available in this broadband router EDI NETWORKING PEOPLE TOGETHER General Setup The Wireless Router supports advanced functions like Virtual Server Access Control Hacker Attack Detection and DMZ We highly recommend you keep the default settings Menu Description This section allows you to set the Broadband System router s system time zone password and remote management administrator This section allows you to set Internet Connection 8G 3 5G via wireless 3G USB modem This section allows you to select the connection WAN method in order to establish a connection with your ISP same as the Quick Setup Wizard section LAN You can specify the LAN segment s IP address subnet Mask enable disable DHCP and select an IP 40 range for your LAN Wireless Setup the wireless LAN s SSID WEP key MAC filtering Qos You can setup the QoS bandwidth control policy You can configure the Address Mapping Virtual Server and Special Applications functions in this NSF section This allows you to specify what user packet can pass your router s NAT Fire
29. this MAC address like ROOM 2A Computer or anything You can input up to 16 alphanumerical characters here This is optional and you can leave it blank however it s recommended to use this field to write a comment for every MAC addresses as a memory aid Add Click Ada button to add the MAC address and associated comment to the MAC address filtering table Reset Remove all inputted values All MAC address entries will be listed in this page 87 MAC Filtering Table No Computer name Client PC MAC address Comment Select E OFFLINE aa bb cc dd ee ff OficePC O EN OFFLINE 11 22 33 44 55 66 abi o Delete Selected Delete All To delete one or more entries listed here please check the box of the mapping entry under Select and click Delete Selected button If you wish to delete all mapping entries click Delete All button To deselect all checked boxes click Reset button If you wish to use IP address based filtering please use IP Filtering Table in this page o Enable IP Filtering Table up to 20 computers Deny Allow Client PC Client PC IP Client Protocol Port Description address Service Range E mail m POS 192 168 98 150 tir O Add PC Delete Selected Delete All Please check Enable IP Filtering Table box first and select Deny or Allow to decide the behavior of IP filtering table Deny the access o
30. to ensure the safe use of the equipment EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria Belgium Denmark Finland France Germany Greece Ireland Italy Luxembourg Bulgaria Cyprus Czech Republic Estonia Hungary Latvia Lithuania Malta Poland Romania Slovakia Slovenia the Netherlands Portugal Spain Sweden and the United Kingdom The ETSI version of this device is also authorized for use in EFTA member states Iceland Liechtenstein Norway and Switzerland EU Countries Not intended for use None CE Mark Warning This is a class B product In a domestic environment this product may cause radio interface in which case the user may be required to make adequate measures A CE declaration of conformity is available on www edimax com cco FCO E 115 EDIMAX NETWORKING PEOPLE TOGETHER EDIMAX Technology Co Ltd wew edimax com
31. use this function in the first time especially your ISP charge you by access time Back Panel The diagram fig1 0 below shows the broadband router s back panel The router s back panel is divided into four sections LAN WAN USB and Reset o HU aa Figure 1 0 1 Local Area Network LAN The Broadband router s 4 LAN ports are where you connect your LAN s PCs hubs switches etc 2 Wide Area Network WAN The WAN port connected to your xDSL or Cable modem which linked to the Internet 3 USB The USB port allow you to share internet via 3G USB modem card 4 WPS Reset button You can press the button 2 4 seconds to enable WPS for wireless security When you experience some problem on using this router or you forgot your password you can press the reset button for longer than 20 seconds and the router will reset itself to the factory default settings warning your original configurations will be replaced with the factory default settings 5 Wireless on off You can enable disable WiFi wireless signal via switch button Front Panel On the router s front panel there are LEDs which shows the status of this router Below is the list of each LED and its description e 36 6200 DIMAX A i gt i 4 nLite Wireless 3G Broadband Router Figure 1 1 LED q Description ON Router is powered on ON WAN is connected hie Off WAN is unconnected Flashing WAN port is s
32. 00000000 00000000 00000111 This is a convenient and efficient method for routers to route IP packets to their destination ISP Gateway Address see ISP listed below for explanations The ISP Gateway Address is an IP address for the Internet router located at the ISP s office ISP Internet Service Provider An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations LAN Local Area Network A LAN is a group of computers and devices connected together in a relatively small area such as a house or an office Your home network is considered as a LAN MAC Address MAC stands for Media Access Control A MAC address is the hardware address of a device connected to a network The MAC address is a unique identifier for a device with an Ethernet interface It comprises two parts 3 bytes of data that corresponds to the Manufacturer ID which is unique for each manufacturer plus 3 bytes that are often used as the product s serial number NAT Network Address Translation This process allows all of the computers on your home network to use one IP address Using the broadband router s NAT capability you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP Port Network Clients LAN PC uses port numbers to identify one network application protocol from another Below is a list of common applications and protocol p
33. 192 168 2 1 255 255 255 0 802 1d Spanning Tree DHCP Server Disable Enable vw e DHCP Server lt Forever 192 168 2 100 192 168 2 200 Lease Time DHCP Client Start IP DHCP Client End IP Domain Name A E APPLY CANCEL Static DHCP Lease Table It allows 16 entries only ICE TE C Enable Static DHCP Leases MAC Address IP Address Parameters Default Description This is the router s LAN port IP IP address 192 168 2 1 address Your LAN clients default gateway IP address IP Subnet Mask 255 255 255 0 Specify a Subnet Mask for your LAN segment 802 1d Spanning Tree Disabled DHCP Server Enabled Lease Time If 802 1d Spanning Tree function is enabled this router will use the spanning tree protocol to prevent from network loop happened in the LAN ports You can enable or disable the DHCP server By enabling the DHCP server the router will automatically give your LAN clients an IP address If the DHCP is not enabled then you ll have to manually set your LAN client s IP addresses make sure the LAN Client is in the same subnet as this broadband router if you want the router to be your LAN client s default gateway When enabled DHCP service will temporarily give your LAN clients an IP address In the Lease Time setting you can specify the time period that the DHCP lends an IP address to your LAN clients The DHCP will change yo
34. AN connection if the time period that no one is using the Internet exceeds the Idle Time If you select Manual the 37 router will connect to ISP only when you click Connect manually from the Web user interface The WAN connection will not be disconnected due to the idle timeout If the WAN line breaks down and latter links again the router will not connect to the ISP by itself The WAN idle timeout auto disconnect function may not work due to abnormal activities of some network application software computer virus or hacker attacks from the Internet For example some software sends network packets to the Internet in the background even when you are not using the Internet This function also may not work with some ISP So please make sure this function can work properly when you use this function in the first time especially your ISP charge you by time used Due to the many uncontrollable issues we do not guarantee the WAN idle timeout auto disconnect function will always work In order to prevent from extra connection fee please TURN OFF THE ROUTER WHEN YOU ARE NOT USING INTERNET Idle Time Out Click lt OK gt when you have finished the configuration above Congratulations You have completed the configuration for the L2TP connection You can start using the router now if you wish to use some of the advance features supported by this router see chapter 2 3 4 1 6 Telstra Big P
35. Filtering Table It allows 20 entries only MAC Address Comment Pwo MmacAddress Comment Select O Enable Access Control A OO commen O APPLY CANCEL Parameters Description Enable wireless Enable wireless access control access control Fill in the MAC Address and Comment of the wireless station to be added and then click Add Add MAC Then this wireless station will be added into the address into the Current Access Control List below If you find any list issues before adding it and want to correct it Just click Clear and both MAC Address and Comment fields will be cleared If you want to remove some MAC address from the Current Access Control List select the MAC mote MAG addresses you want to remove in the list and then click address from list Delete Selected If you want remove all MAC addresses from the table click Delete All button Click Reset will clear your current selections Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 66 2 5 5 WPS WPS Wi Fi Protected Setup provides a convenient way to establish the connection between this broadband router and wireless clients Any WPS compatible wireless clients can establish secure connection with this broadband router with simple push button type configuration or PinCode type configuration
36. IP for more detail 2 3 3 PPPoE PPP over Ethernet Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet Your ISP should provide all the information required in this section See chapter 1 PPPoE for more detail 2 3 4 PPTP Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet Your ISP should provide all the information required in this section See chapter 1 PPTP for more detail 2 3 5 L2TP Select L2TP if your ISP requires the L2TP protocol to connect to the Internet Your ISP should provide all the information required in this section See chapter 1 L2TP for detailed information 2 3 6 Telstra Big Pond Select Telstra Big Pond if your ISP requires the Telstra Big Pond protocol to connect to the Internet Your ISP should provide all the information required in this section Telstra Big Pond protocol is used by the ISP in Australia See chapter 1 Telstra Big Pond for more detail 50 2 3 7 DNS A Domain Name System DNS server is like an index of IP addresses and Web addresses If you type a Web address into your browser such as www router com a DNS server will find that name in its index and the matching IP address Most ISPs provide a DNS server for speed and convenience lf your Service Provider connects you to the Internet with dynamic IP settings it is likely that the DNS server IP address is provided automatically However if there is a
37. IP address has been designated the Remote Management host IP address for this router located in your company office then you ll be able to configure this router from your home If the Host Address is 0 0 0 0 means anyone can access the router s web based configuration from a remote location if they know the password Click the Enabled box to enable the Remote Management function Note When you want to access the web based management from a remote computer you must enter the router s WAN IP address e g 10 0 0 1 into your web browser followed by colon and port number 8080 e g 10 0 0 1 8080 see below You ll also need to know the password set in the Password Setting screen in order to access the router s web based management nor mb 3 ES to Fess 10 0 0 1 58060 JIA gt DAP yor 45 Port Enabled The port number of remote management web interface Select Enabled to enable the remote management function Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advanced functions or start using the router with the advanced settings in place 46 2 2 3G 3 5G 3G 6200n provides two types of Internet connection method wireless 3G 3 5G or wired connection You can access internet via USB 3G 3 5G modem card or via wired xDSL cable modem connection However only one connection method wireless or wired can be used at the same time Re
38. Internet which must be assigned by InterNIC TCP IP UDP Transmission Control Protocol Internet Protocol TCP IP and Unreliable Datagram Protocol UDP TCP IP is the standard protocol for data transmission over the Internet Both TCP and UDP are transport layer protocol TCP performs proper error detection and error recovery and thus is reliable UDP on the other hand is not reliable They both run on top of the IP Internet Protocol a network layer protocol WAN Stands for Wide Area Network A network that connects computers located in geographically separated areas e g different 111 buildings cities countries The Internet is a wide area network too Web based management Graphical User Interface GUI Many devices support graphical user interface that is based on the web browser This means the user can use their familiar web browser ex Netscape or Microsoft Internet Explorer to control configure or monitor the device being managed 112 Federal Communication Commission Interference Statement FCC Part 68 This equipment complies with Part 68 of the FCC Rules On the bottom of this equipment is a label that contains the FCC Registration Number and Ringer Equivalence Number REN for this equipment You must provide this information to the telephone company upon request The REN is useful to determine the quantity of devices you may connect to the telephone line and still have all of those devices ring when you
39. PC for the Clone MAC Address button to work To find out the PC s MAC address see Appendix A see Glossary for an explanation on MAC address Use the following IP Address IP Address The ISP gave you a static IP to be used to connect to the L2TP server This is the IP address that your ISP has given you to establish a L2TP connection Subnet Mask Enter the Subnet Mask provided by your ISP e g 255 255 255 0 Gateway Enter the IP address of the ISP Gateway User ID Enter the User Name provided by your ISP for the PPTP connection Sometimes called a Connection ID Password Enter the Password provided by your ISP for the PPTP connection L2TP Gateway If your LAN has a L2TP gateway then enter that L2TP gateway IP address here If you do not have a L2TP gateway then enter the ISP s Gateway IP address above MTU This is optional You can specify the maximum size of your transmission packet to the Internet Keep default value if you do not wish to set a maximum packet size Connection Type If you select Continuous the router will maintain the connection to the ISP If the WAN line breaks down and links again at a latter time the router will auto reconnect to the ISP If you select Connect On Demand the router will connect to the ISP automatically when someone wants to use the Internet and keep connected until the WAN idle timeout The router will close the W
40. Port Range The range of ports to be forward to the private IP Comment The description of this setting Add Port Fill in the Private IP Type Port Range and Forwarding Comment of the setting to be added and then click 74 Add Then this Port Forwarding setting will be added into the Current Port Forwarding Table below If you found any typo before adding it and want to correct it just click Clear and the fields will be cleared If you want to remove some Port Forwarding settings from the Current Port Forwarding Table select the Port Forwarding settings you want to remove in the table and then click Delete Selected If you want remove all Port Forwarding settings from the table just click Delete All button Click Reset will clear your current selections Remove Port Forwarding Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 75 2 7 2 Virtual Server Use the Virtual Server function when you want different servers clients in your LAN to handle different service Internet application type e g Email FTP Web server etc from the Internet Computers use numbers called port numbers to recognize a particular service Internet application type The Virtual Server allows you to redirect a particular service port number from the Internet WAN Port to a particular LAN
41. Setup Wizard in the CD ROM provided in the package The wizard provides quick setup for wireless 3G 3 5G Internet connection Ethernet WAN Internet connection SSID wireless security firmware upgrade and changing router s password When you start the Setup Wizard you will get the following Welcome screen Please choose the language to start with and follow the easy steps in the Wizard No instruction for the Setup Wizard is given here If you lost the CD ROM or you prefer the traditional web setup please follow the procedures in Manual to configure the router English Nederlands Deutsch Francais Italiano Espa ol Portugu s Polski Cesky Magyar Pycckuh Romana T rk e 4 YxX CTX gt EDIMAX Routers www edimax com Contact us Note 1 Only one Internet connection wireless 3G or xDSL Cable can be used at the same time Note 2 To prevent the compatibility problem between 3G USB Modem cad and 3G router it is recommended that you upgrade the latest firmware of 3G router from Edimax website http www edimax com Features Provides IEEE 802 11g b wireless LAN access point Compatible with IEEE 802 11n standard with 150Mbps data rate High Internet access throughput Allow multiple users to share a single Internet connection Supports up to 253 network client users Provides one USB port for 3G wireless connection Internet Access via 3G modem or Cable or xDSL modem Access Servers on your LAN from the Public N
42. Shopping Weather Gite City Guides Health amp Fitness Movies Spaces White Pages l MSN Directory Dating amp Personals Horoscopes Music Sports Yellow Pages MSNBC News How to Leave Your Husband da F E Ferry capsize could send F A Asia typhoon toll higher Financial tips that will f NYT Are McCain and Dole q a J Vonage Unlimited really so similar local amp long Winehouse has lung damage dad says distance calling Miss River crests Video Worst over A Video Bringing home the grief of war Plus 10 steps to a lt mn he only 99 money smart divorce Mo LS gt FOX Sports HE A Wimbledon preview How will LUCK HERE the favorites fare Draws CLICK HERE Today s Picks Ganindies y A Game over Pacman wants to Photographer claims mob of i Comedian drop nickname Play fantasy Malibu surfers attacked him suffers heart Drag racers on track day after tragic crash Would be teachers best bet failure at 71 Spain stuns Italy on penalty kicks Photos Advertisement Ad feedback MD Internet pay off in the long run lt Previous o Next gt 27 Note If your SIM card requires entering the PIN code please enter into the web management of the 3G router In WAN setting web page select 3G 3 5G Enter the PIN code of the adapter Please input User name amp Password in PPP Settings and do not input them in Network Settings unless your ISP ask you input them in both
43. Upgrade System Firmware 3 11 2009 9 43 01 Parameters Description You can save the router s current configuration Configuration restore the configuration from previously saved Tools configuration files and restore the router s factory default settings Firmware This page allows you to upgrade the router s Upgrade firmware Reset When you encounter any problem using this broadband router you can reset the router by this function Select one of the above Tools Settings selections and proceed to the relevant sub section 4 1 Configuration Tools The Configuration Tools screen allows you to save Backup the router s current settings Saving the configuration settings provides an added protection and convenience when there re some problems with the router and you have to reset to factory default to solve the problem When you save the configuration setting Backup you can reload the saved configuration to the router through the Restore selection If extreme problems occur you can use the Restore to Factory Defaults 103 selection this will set all configurations to its original default settings e g when you purchased the router Configuration Tools 2 Use the Backup tool to save the Wireless Router s current configurations to a file named config bin You can then use the Restore tool to restore the saved configuration to the Wireless Router Alternatively you can use the Restore to Factory Defa
44. above Note You need to give your LAN PC clients a fixed static IP address for DMZ to work properly 94 Chapter 3 Status The Status section allows you to monitor the current status of your router You can use the Status page to monitor the connection status of the Broadband router s WAN LAN interfaces the current firmware and hardware version numbers any illegal attempts to access your network and information on all DHCP client PCs currently connected to your network Status 2 The Wireless Router s status information provides the following information about your Wireless Router Hardware Firmware version Serial Number and its current operating status System Lo Model 3G 6200N Wireless 3G Router Oday Oh Om 33s Parameters Description Status and Shows the router s system information Information Internet View the Broadband router s Internet connection Connection status and other related information Device Status View the Broadband router s current settings System Log View the Broadband router s system log Security Log View any attempts that have been made to gain access to your network Active DHCP View your LAN client s information that is currently Client linked to the broadband router Statistics Shows the statistics 95 Select one of the above Status selections and proceed to the manual s relevant sub section Status and Information
45. d select one of them as default key Then the router can receive any packets encrypted by one of the four keys This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network WEP v LORA 64 bit STRUER Hex 10 Characters Y DST OA Key 1 FERRERA Encryption Key 1 Encryption Key 2 REE Encryption Key 3 Encryption Key 4 Shaina Enable 802 1x Authentication APPLY CANCEL Parameters Default Description You can select the WEP key length for 64 bit encryption 64 bit or 128 bit Larger WEP Key Length key length will provide higher level of security but the data throughput will be lowered You can select ASCII Characters alphanumeric format or Hexadecimal Digits A F a f and 0 9 to be the WEP Key For example ASCII Characters guest Hexadecimal Digits 12345abcde Key Format 60 Default Key Select one of the four keys to encrypt your data Only the key you select it in the Default key will be used Key 1 Key 4 The WEP keys are used to encrypt data transmitted over the wireless network Fill the text box by following the rules 64 bit WEP input 10 digit Hex values in the A F a f and 0 9 range or 5 digit ASCII character as the encryption keys 128 bit WEP input 26 digit Hex values A F a
46. d then a WDS Security Settings will pop up You can set the security parameters used to bridge access points together here when you set your AP in AP Bridge mode You can refer to section 4 3 Security Settings for detailed instructions Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advanced sections or start using the router with the advanced settings in place 57 2 5 2 Advanced Settings You can set advanced wireless LAN parameters of this router The parameters include Authentication Type Fragment Threshold RTS Threshold Beacon Interval preamble Type etc You should not change these parameters unless you know their function and effects Advanced Settings 2 set the time zone ofthe Wireless Router This information is used for log entries and firewall settings SEU E 2346 256 2346 EME 2347 0 2347 Beacon Interval 20 1000 ms DTIM Period 1 10 DEE Auto Y DEA Auto Y ALO LA Auto 20 40 MHZ 20 MHZ Short Preamble O Long Preamble AA TA Enable O Disable ASA O Auto O Always None Tx Power 100 Y O Enable Disable Too PEA g o Preamble Type Parameters Description Fragment Fragment Threshold specifies the maximum ach old fragmentation size of data packet to be transmitted If this value is too low it will result in bad performance RTS When the packet size is small
47. des Internet service Type Select the type of connection TCP or UDP If you re not sure please select Both Public Port Please select the port number of Internet IP address which will be redirected to the port number of local IP address defined above Comment Please input any text to describe this mapping up to 16 alphanumerical characters Add Add the mapping to virtual server table Reset Remove all inputted values All existing virtual server mappings will be displayed in this page To delete one or more mappings check the box of the mapping then click Delete Selected button to remove the mapping To delete all existing mappings click Delete All button If you want to uncheck all boxes click Reset When you finished with the settings in this page you can click Apply button to save changes you made in this page or you can click Cancel to discard changes After you click Apply button you ll see the following messages Save setting successfully Please press APPLY button to restart the system for changes to take effect Apply Please click Apply to save changes you made and restart the broadband router this requires about 30 seconds and the broadband router will stop responding this is normal and is not malfunction You can reconnect to this broadband router and continue on other settings later 77 2 7 3 Special Applications Some application
48. dress You must get an account password and your static domain 51 name from the DDNS service providers This router supports DynDNS TZO and other common DDNS service providers DDNS DynamicDNS allows users to map the static domain name to a dynamic IP address You must get a account password and your static domain name from the DDNS service providers Our products have DDNS support for www dyndns org and www tzo com now WET kee O Enable Disable Provider Passwort APPLY CANCEL Parameters Default Description Enable Disable Disable Enable Disable the DDNS function of this router Provider Select a DDNS service provider Domain name Your static domain name that use DDNS The account that your DDNS Account E mail service provider assigned to you The password you set for the Password Key DDNS service account above Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 52 2 4 LAN The LAN Port screen below allows you to specify a private IP address for your router s LAN ports as well as a subnet mask for your LAN segment You can enable the Wireless Routers DHCP server to dynamically allocate IP Addresses to your LAN client PCs The Wireless Router must have an IP Address in the Local Area Network gt IP Address Subnet Mask
49. e as using the software will indicate your assent Y O 1 do not accept the terms in the license agreement InstallShield 23 8 If you want to change the destination folder please click Change Click Next to continue i BandLuxe HSDPA Utility R1 InstallShield Wizard W Destination Folder Click Next to install to this Folder or click Change to install to a different Folder Install BandLuxe HSDPA Utility R1 to C Program Files BandRich BandLuxe HSDPA utility R11 i Cancel 9 Click install i BandLuxe HSDPA Utility R1 InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation Tf you want to review or change any of your installation settings click Back Click Cancel to exit the wizard 24 10 The system is installing the driver and utility of the adapter fe BandLuxe HSDPA Utility R1 InstallShield Wizard Installing BandLuxe HSDPA Utility R1 The program features you selected are being installed Please wait while the InstallShield Wizard installs BandLuxe HSDPA Utility R1 This may take several minutes Status a InstallShield Cancel 11 Install successfully click Finish to close the install wizard ie BandLuxe HSDPA Utility R1 InstallShield Wizard InstallShield Wizard Completed The InstallShield Wizard has successfully installed BandLuxe HSDPA Utility R1 Click
50. e program is free software and distributed without any warranty of the author We offer valid for at least three years to give you for a charge no more than the costs of physically performing source distribution a complete machine readable copy of the corresponding source code Please contact Edimax at Edimax Technology co Ltd NO 3 Wu Chuan 3rd RD Wu Ku Industrial Park Taipei Hsien Taiwan R O C TEL 886 2 77396888 FAX 886 2 77396887 sales edimax com tw X The product you have purchased and the setup screen may appear slightly different from_ those shown in this QIG For more detailed information about this product please refer to the User s Manual on the CD ROM X Software and specifications subject to change without notice Please visit our web site for the update X All rights reserved Trademarks or registered trademarks are the property of their respective holders io AA A Aaa ae Me ae 4 sn eet tied cee a oes cue Ses enews eee ses ee Oe tes ee een eee 18 1 1 Cable Mode 00 30 12 Fixed AE Deo anes Rs 31 IESE A d FOL E E amp aumn em enaemataad 32 AAR Le siena ca UN Scan Sb aan indeed RO 34 A cians brennan seni oan sen meet eae eet 36 TG TESTA Big GING A aio 38 Chapte o cert ee ett rnd ce err S 40 BA OV GIO Mira cdi eine aA eds O as 42 VM TME ZoNe Src tate eres sate ae ek ase Seki alas be stats ea ode etek ea ess ed eects 43 2 1 2 Password Settings ccocccocccccnnnooococccnncccnnnnnnnnnnncnnnnnnnnnnnn nn nn n
51. e risk of hacker attack and defending against a wide array of common attacks However for applications that require unrestricted access to the Internet you can configure a specific client server as a Demilitarized Zone DMZ Firewall Module Enable Disable APPLY Parameters Description Access Access control allows you to specify which computer 85 Control can or cannot access to certain Internet applications URL Blocking URL Blocking allows you to specify which URLs can not be accessed by users DoS The Broadband router s firewall can block common hacker attacks and can log the attack activities The DMZ function allows you to redirect all packets DMZ going to your WAN port IP address to a particular IP address in your LAN Click on one of the firewall selections and proceed to the manual s relevant sub section 2 8 1 Access Control If you want to restrict users from accessing certain Internet applications services e g Internet websites email FTP etc this is the place to set that configuration Access Control allows users to define the traffic type permitted in your LAN You can control which PC client can have access to these services Access Control allows users to define the traffic type permitted or not permitted in your LAN You can control which PC client uses what services in which they can have access to these services If both of MAC filtering and IP fi
52. ections Point to Point Tunneling Protocol is a common _ connection method used in xDSL connections Layer Two Tunneling Protocol is a common connection o dE method used in xDSL connections Telstra Big Pond a Pond is a Internet service is provided in Parameters Description Your ISP will assign you an IP address Dynamic IP l automatically Static IP Your ISP gave you an IP address already PPPoE Your ISP requires PPPoE connection Your ISP requires you to use Point to Point PPTP Tunneling Protocol PPTP connection L2TP Your ISP requires L2TP connection Telstra Big Pond Your ISP requires Telstra Big Pond connection DNS You can specify a DNS server that you wish to use You can specify a DDNS server that you wish to use DDNS and configure the user name and password provided by you DDNS service provider Once you have made a selection click lt More Configuration gt at the bottom of the screen and proceed to the manual s relevant sub section 2 3 1 Dynamic IP Choose the Dynamic IP selection if your ISP will assign you an IP address automatically Some ISP s may also require that you fill in additional information such as Host Name Domain Name and MAC address see chapter 1 Cable Modem for more detail 49 2 3 2 Static IP Address Select Static IP address if your ISP assigned you with a specific IP address for you to use Your ISP should provide all the information required in this section See chapter 1 Fixed
53. ending receiving data LAN ON LAN port is connected LNK ACT Off LAN port is unconnected eres Flashing LAN port is sending receiving data ON 3G USB modem is connected 3G Off 3G USB modem is not connected Flashing 83G USB modem card is sending receiving data ON Wireless LAN has been activated G amp S Off Wireless LAN is disabled Flashing Wireless LAN is sending receiving data Setup Diagram A 3G 3 5G Modem card installation If you have 3G 3 5G modem card and SIM card please follow the following instructions to establish connection 1 Connect power adapter to 3G 6200n 2 Gonnect another Ethernet cable from the any LAN ports 1 4 on router to Ethernet socket on the PC Broadband Router t f Laptop Desktop PC 3 Insert SIM card into 3G 3 5G modem card and connect the modem card with one of USB port of 3G 6200n The corresponding USB LED indicator on 3G 6200n will light 3G 3 5G USB Modem 3G 3 5G USB Modem Computer B Cabling installation If you can also access Internet by xDSL Cable modem please follow the following instructions 1 Connect the Ethernet cable from the router s WAN port to the LAN port of the modem STEP 1 Fo veros CA Ma Broadband Router t f ADSL Cable Modem 2 Connect another Ethernet cable from the any LAN ports 1 4 on router to the Ethernet socket on the PC STEP 2 Broadband Router t f Laptop Desktop PC 3 Check to make sure the
54. enial of Service ai ire 93 A A 94 A heat eat ea hee tee hae ea mentee ete her eee 95 3 tStat sand IMOKMANON a chute heen een tat ban cts cu tan catia 96 32 B ef ance fe Vs eee Ree Ree te adada iiil ri EEEE TE ia e pre re 98 Did OV SION HOO idad 99 3 4 Sec rity Log AA AAA AAA ee omen ieee AA Mes 100 3 5 Active DHOP Gt ee ea oem tnecco tec nhuanacteganasaien ahead ohremanuge oe ees 101 3 6 Statistics ret ate teat hia da ada adele Madi E as ties 102 Chapter neee tadscaas tudavees Gudstned Cadesiuest Salaceat Suds ees tadeteat Cade ieadadstuet E 103 4 1 Configuration Tools scx ltd titi 103 4 2 Firmware Upgrade AA Sin ta a Chae aE Sin Se ata te 104 AROS dc ooo caos 105 A tte E a E S E teed tabs cat ents 107 OS SAY acres eer ents Se cee eee omc eae eee eae cmt 109 Introduction Thank you for purchasing Edimax 3G 6200n nLite wireless 3G broadband router This high cost efficiency router is the best choice for Mobile Small office Home office users all computers and network devices can share a single wireless 3G modem or xDSL cable modem internet connection at high speed Easy install procedures allows any computer users to setup a network environment in very short time within minutes even inexperienced When the number of your computers and network enabled devices grow you can also expand the number of network slot by simple attach a hub or switch to extend the scope of your network You can configure the router by running the
55. er LED stops blinking Once the reset process is complete you may start using the router 106 Appendix A How to find your PC s IP and MAC address manually 1 In Window s open the Command Prompt program Microsoft Windows 2666 Version 5 00 2195 lt C Copyright 1985 1999 Microsoft Corp GN 2 Type Ipconfig all and lt enter gt Microsoft Windows 2666 Version 5 66 2195 lt C gt Copyright 1985 1999 Microsoft Corp C gt ipconfig all Windows 2606 IP Configuration Host Name Primary DNS Suffix Node Type IP Routing Enabled WINS Proxy Enabled pete E Broadcast No x a No Ethernet adapter Local Area Connection Connection specific DNS Suffix Description a aaa Realtek RTL8139 lt A gt PCI Fast Ethernet Adapter 66 56 FC FE 62 DB Yes Yes 192 168 1 77 255 255 255 0 192 168 1 254 192 168 1 1 192 168 1 1 139 175 55 244 Sunday December 09 2661 9 18 45 PM Physical Address DHCP Enabled Autoconf iguratio IP Address Subnet Mask Default Gateway DHCP Server DNS Servers se eee Dee see se 8 Mee see es Mee yl a Lease Obtained Friday December 14 2061 9 18 45 PM Lease Expires 107 e Your PC s IP address is the one titled as IP address 192 168 1 77 in this example eThe routers IP address is the one titled as Default Gateway 192 168 1 254 in this example eYour PC s MAC Address is the one titled as Phy
56. er the RTS threshold the wireless access point will not use the RTS CTS as mechanism to send this packet Beagan The interval of time that this wireless access point interval broadcast a beacon Beacon is used to synchronize the wireless network The DTIM period you specify here indicates how DTIM Period often the clients served by this access point should check for buffered data which still exists on the AP 58 and waiting for pickup The Data Rate is the rate this access point used to transmit data packets The access point will use the pala Rale highest possible selected transmission rate to transmit the data packets N Data Rate We provide MCS0 MCS7 and Auto for configuration and default setting is Auto The default setting is Auto 20 40MHz and the Channel Width default setting will provide you better wireless performance than 20MHz The Long Preamble can provide better wireless Preamble LAN compatibility while the Short Preamble can yP provide better wireless LAN performance If you enable Broadcast ESSID every wireless station located within the coverage of this access Broadcast point will discover this access point more easily If ESSID you are building a wireless network which will open to the public it s recommended to enable this feature Disabling Broadcast ESSID can provide better security It is recommended t
57. etwork Equipped with four LAN ports 10 100M and one WAN port 10 100M Support DHCP Server Client for easy setup Support advance features such as special applications DMZ virtual server access control firewall Allow you to monitor the router s status such as DHCP Client Log System Log Security Log and Device Connection Status Easy to use Web based GUI for configuration and management Remote Management allows configuration and upgrades from a remote site over the Internet Minimum Requirements One External xDSL ADSL or Cable modem with an Ethernet port RJ 45 Network Interface Card NIC for each Personal Computer PC Computer with a Web Browser Internet Explorer 5 0 or higher Netscape Navigator 7 2 or higher Package Contents One Wireless 3G broadband router One Quick Installation Guide One CD ROM Wizard Multi languages QIG and User Manual One Power Adapter Ethernet Cable Holding base Accessories Note The WAN idle timeout auto disconnect function may not work due to abnormal activities of some network application software computer virus or hacker attacks from the Internet For example some software sends network packets to the Internet in the background even when you are not using the Internet So please turn off your computer when you are not using it This function also may not work with some ISP So please make sure this function can work properly when you
58. ey APPLY CANCEL Parameters Description WPA TKIP TKIP will change the encryption key frequently to enhance the wireless LAN security WPA2 AES uses CCMP protocol to change encryption WPA2 AES key frequently AES can provide high level encryption to enhance the wireless LAN security WPA Mixed WPA2 Mixed will use TKIP or AES based on the other communication peer automatically You may select Passphrase alphanumeric format or Hexadecimal Digits in the A F a f and 0 9 range to be the Pre shared Key For example Passphrase iamguest Hexadecimal Digits 12345abcde The Pre shared key is used to authenticate and encrypt data transmitted over the wireless network Fill the text box by following the rules listed here Hex WEP input 64 digit Hex values A F a f and 0 9 or at least 8 character pass phrase as the pre shared keys Pre shared Key Format Pre shared Key Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 64 2 5 3 5 WPA Radius Wi Fi Protected Access WPA is an advanced security standard You can use an external RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication lt uses TKIP or CCMP AES to change the encryption key frequently and this will improve security This page
59. f IP addresses in the list or allow the access of IP addressees in the list You have to click Add PC button to add a new IP address to the list Access Control Add PC This page allows users to define service limitation of client PC including IP address and service type Client PC Description E Client PC IP address Here are descriptions of every setup items ltem Name Description Client PC Description Please input any text to describe this IP address up to 16 alphanumerical characters Client PC IP address Please input the starting IP address in the left field and input the end IP address in the right field to define a range of IP addresses or just input the IP address in the left field to define a single IP address You also have to select the type of Internet services that will be applied to this access control rule from the list Client PC Service PN Sonico ame TN Select www HTTP TCP Port 80 3128 8000 8080 8081 O E mail Sending SMTP TCP Port 25 J News Forums NNTP TCP Port 119 in E mail Receiving POP3 TCP Port 110 O Secure HTTP HTTPS TCP Port 443 O File Transfer FTP TCP Port 21 O MSN Messenger TCP Port 1863 O Telnet Service TCP Port 23 O AIM AOL Instant Messenger TCP Port 5190 O NetMeeting H 323 TCP Port 389 522 1503 1720 1731 O DNS UDP Port 53 O SNMP UDP Port 161 162 O VPN PPTP TCP
60. f your ISP will assign you with an IP address automatically i e DHCP Some ISP s may also require that you fill in additional information such as host name and MAC address see screen below Note The Host Name and MAC address section is optional and you can skip this section if your ISP does not require these settings Dynamic IP Cable Modern fF Hosttame MAC Address 000000000000 Clone MAC Parameters Description If your ISP requires a Host Name type in the host Host Name name provided by your ISP otherwise leave it blank if your ISP does not require a Host Name Your ISP may require a particular MAC address to connect to the Internet This MAC address is the PC s MAC address that your ISP had originally connected your Internet connection to Type in this MAC address in this section or use the Clone MAC MAC Address Address button to replace the WAN MAC address with the MAC address of that PC you have to be using that PC for the Clone MAC Address button to work To find out the PC s MAC address see Appendix A see Glossary for an explanation on MAC address Click lt OK gt when you have finished the configuration above Congratulations You have completed the configuration for the Cable Modem connection You can start using the router now if you wish to use some of the advance features supported by this router see chapter 2 3 4 30 1 2 Fixed IP xDSL Select Fi
61. h the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio 113 frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person s body excluding extremities of hands wrist and feet during wireless modes of operation This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and
62. ick Network and Dial up Connections icon In the Network and Dial up Connection window double click Local Area Connection icon The Local Area Connection window will appear 3 In the Local Area Connection window click the Properties button 4 Check your list of Network Components You should see Internet Protocol TCP IP on your list Select it and click the Properties button 5 In the Internet Protocol TCP IP Properties window select Obtain an IP address automatically and Obtain DNS server address automatically as shown on the following screen Internet Protocol TCP IP Properties E ax General You can get IP settings assigned automatically if pour network supports this capability Otherwise you need to ask pour network administrator for the appropriate IP settings Obtain an IP address automatically C Use the following IP address IP address Subnet mast Default gateway Obtain DNS server address automatically C Use the following DNS server addresses Preferred DNS server Altenate DNS server Advanced 6 Click OK to confirm the setting Your PC will now obtain an IP address automatically from your Broadband Router s DHCP server Note Please make sure that the Broadband router is the only DHCP server on your LAN Once you ve configured your PC to obtain an IP address automatically please proceed to Step 3 2d Windows NT 1 Click the Start button and select Sett
63. ill be cleared Remove a Rule If you want to remove some routing rules from the Static Routing Table select the rules you want to remove in the table and click Delete Selected If you want remove all rules from the table just click Delete All button Click Reset will clear your current selections Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 84 2 8 Firewall This broadband router provides extensive firewall protection by restricting connection parameters thus limiting the risk of hacker attack and defending against a wide array of common Internet attacks However for applications that require unrestricted access to the Internet you can configure a specific client server to be located in Demilitarized Zone DMZ Note To enable the Firewall settings select Enable and click Apply Firewall 2 The Wireless Router provides extensive firewall protection by restricting connection parameters thus limiting the risk of hacker attack and defending against a wide array of common attacks However for applications that require unrestricted access to the Internet you can configure a specific client server as a Demilitarized Zone DMZ Firewall Module Enable Disable APPLY Firewall 2 The Wireless Router provides extensive firewall protection by restricting connection parameters thus limiting th
64. indicates 50 port numbers Traffic Type Select the traffic type of the packets that this rule will apply to We list some popular applications here to ease the configuration You also can get the same result by using other parameters for example source or destination port number if you are familiar with the application protocol Protocol Select the protocol type of the packets that this rule will apply to Apply Reset Apply and exit the form Clear the content of this form Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 71 2 7 NAT Network Address Translation NAT allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses NAT provides Firewall protection from hacker attacks and has the flexibility to allow you to map private IP addresses to public IP addresses for key services such as Websites and FTP NAT 2 key services such as the Web or FTP NAT Module Enable Disable APPLY Parameters Description You can have different services e g email FTP Web etc going to different service servers clients in your Port LAN The Port Forwarding function allows you to Forwarding redirect a particular range of service port numbers from the Internet WAN Ports to a particular LAN IP address Virtual Ser
65. ings then click Control Panel The Control Panel window will appear 2 Double click Network icon The Network window will appear Select the Protocol tab from the Network window 3 Check if the TCP IP Protocol is on your list of Network Protocols If TCP IP is not installed click the Add button to install it now If TCP IP is installed go to step 5 4 In the Select Network Protocol window select the TCP IP Protocol and click the Ok button to start installing the TCP IP protocol You may need your Windows CD to complete the installation 5 After you install TCP IP go back to the Network window Select TCP IP from the list of Network Protocols and then click the Properties button 6 Check each of the tabs and verify the following settings e IP Address Select Obtain an IP address from a DHCP server e DNS Make all fields blank e WINS Make all fields blank e Routing Make all fields blank Microsoft TCP IP Properties 1 fx IP Address DNS WINS Address Routing n IP address can be automatically assigned to this network card by a DHCP server If pour network does not have a DHCP server ask pour network administrator for an address and then type it in the space below Adapter Obtain an IP address from a DHCP server Specify an IP address IF Zddiess i Subnet Mask Deraultisatewnay i Advanced 7 Click OK to confirm the setting Your PC will now obtain an IP address
66. ion and setup the routing rules manually Click on one of the above NAT selections and proceed to the manual s relevant sub section 73 2 7 1 Port Forwarding The Port Forwarding allows you to redirect a particular range of service port numbers from the Internet WAN Ports to a particular LAN IP address It helps you to host some servers behind the router NAT firewall Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall These settings are only necessary if you wish to host some sort of server like a web server or mall server on the private local network behind your Gateway s NAT firewall C Enable Port Forwarding Select Both v Current Port Forwarding Table Eno Computer Name Private P Type PortRange Comment Select APPLY CANCEL Parameters Description Enable Port Enable Port Forwarding Forwarding This is the private IP of the server behind the NAT firewall Private IP Note You need to give your LAN PC clients a fixed static IP address in order to make port forwarding function working properly Computer For you to choose PC or NB Name This is the protocol type to be forwarded You can choose to forward TCP or UDP packets only or select both to forward both TCP and UDP packets Type
67. join a network obtain an IP address convey its capabilities and learn about the presence and capabilities of other devices all automatically truly enabling zero configuration networks Devices can subsequently communicate with each other directly thereby further enabling peer to peer networking UPnP Feature Enable Disable Parameters Default Description UPnP Feature Disable You can Enable or Disable UPnP feature here After you enable the UPnP feature all client systems that support UPnP like Windows XP can discover this router automatically and access the Internet through this router without any configuration The NAT Traversal function provided by UPnP can let applications which support UPnP smoothly connect to Internet websites and avoid any incompatibility problem due to the NAPT port translation Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 81 2 7 5 ALG Settings You can select applications that require Application Layer Gateway support Below are applications that need router s special support to make them work under the NAT You can select applications that you are using COI Comment Amanda Support for Amanda backup tool protocol Egg Support for eggdrop bot networks FTP Support for FTP H323 Support for H323 netmeeting IRC Allows DCC to work though NAT and con
68. lated instructions will be given as follow 3G 6200n supports most of 3G 3 5G modem cards just connect the modem card to the USB port of 3G 6200n and 3G 6200n will recognize it automatically no additional setup procedure required However some of modem cards require PIN code or account password you have to use 3G 6200n s web interface to input these information and some modem cards requires you to connect the modem card with your PC and install driver utility before you connect it with 3G 6200n all PCs which need to access Internet by 3G 6200n requires to perform this procedure once If you still not able to connect to Internet please use wired Internet connection to access our website http www edimax com download latest version of firmware and upgrade 3G 6200n s firmware If you still not be able to get connected by your 3G 3 5G modem card please contact your dealer of purchase and provide the model name of the 3G 3 5G modem card you have we ll try our best to help you to solve the problem Only one Internet connection wireless wired can be used at the same time Wireless connection 3G 3 5G will be selected first and use wired Internet connection as backup Therefore please DO NOT connect your 3G 3 5G modem card with 3G 6200n or your telecomm service provider may charge you with high communication fee For example if you connect 3G 3 5G modem card with 3G 6200n when you re using wired Internet connection wired con
69. ltering are enabled simultaneously the MAC filtering table will be checked first and then IP filtering table C Enable MAC Filtering Deny O Allow e Select Current MAC Filtering Table Cl Enable IP Filtering Deny O Allow Add PC APPLY CANCEL Here are descriptions of every setup items Item Name Description Enable MAC Filtering Check this box to enable MAC address based filtering and please select Deny or Allow to 86 decide the behavior of MAC filtering table If you select deny all MAC addresses listed in filtering table will be denied from connecting to the network if you select allow only MAC addresses listed in filtering table will be able to connect to the network and rejecting all other network devices Client PC MAC address Please input the MAC address of computer or network device here dash or colon are not required i e If the MAC address label of your wireless device indicates aa bb cc dd ee ff or aa bb cc dd ee ff just input aabbccddeeff Computer Name All computer names found by this broadband router on local network will be listed here You can select the computer name and click lt lt button to add selected computer s IP address to Private IP field Please note that this list may not be able to list all computers on your local network Comment You can input any text here as the comment of
70. m up or down Note If the total assigned bandwidth of higher priority applications is larger than the maximum bandwidth provided by the WAN port then other applications will not get any bandwidth QoS 2 QoS Quality of Service refers to the capability of a network to provide better service to selected network traffic The primary goal of QoS is to provide priority including dedicated bandwidth controlled jitter and latency required by some real time and interactive traffic and improved loss characteristics Also important is making sure that providing priority for one or more flows does not make other flows fail Cl Enable QoS AT Select gt gt 0 kbits INTENTA Select Y 0 kbits Current QoS Table Parameters Description You can check Enable QoS to enable QoS function Enable QoS for the WAN port You also can uncheck Enable QoS to disable QoS function for the WAN port Total Here you can set maximum download bandwidth for Download all the users of the router 69 Bandwidth Total Upload Bandwidth Here you can set the maximum upload bandwidth for all the users of the router Add a QoS rule into the table Click Add and the QoS rule form will appear Click Apply after filling the form and the rule will be added into the table Remove QoS If you want to remove some QoS rules from the table select the QoS rules you
71. me specific Internet application e g Games properly from behind the NAT firewall then you can open the client up to unrestricted two way Internet access by defining a DMZ Host The DMZ function allows you to redirect all packets going to your WAN port IP address to a particular IP address in your LAN The difference between the virtual server and the DMZ function is that the virtual server redirects a particular service Internet application to a particular LAN client server whereas DMZ redirects all packets regardless of services going to your WAN IP address to a particular LAN client server DMZ 2 If you have a local client PC that cannot run an Internet application properly from behind the NAT firewall then you can open the client up to unrestricted two way Internet access by defining a Virtual DMZ Host J Enable DMZ Dynamic IP Session 1 O Static IP su Select y Current DMZ Table APPLY CANCEL Parameters Description Enable disable DMZ Note If there s confliction between the virtual server and the DMZ setting the virtual server function will have priority over the DMZ function Public IP The IP address of the WAN port or any other public Address IP addresses assigned to you by your ISP Enable DMZ Input the IP address of a particular host in your LAN that will receive all the packets originally Client PC IP going to the WAN port Public IP address listed Address
72. n Rule Name The name of this rule You can assign the download or upload bandwidth in Kbps 1024 bit per second You can limit the Bandwidth maximum bandwidth consumed by this rule by selecting Maximum You also can reserve enough bandwidth for this rule by selecting Guarantee Enter the local IP address range of the packets that Local IP this rule will apply to If you assign 192 168 2 3 Address 192 168 2 5 it means 3 IP addresses 192 168 2 3 192 168 2 4 and 192 168 2 5 Enter the local port range of the packets that this rule will apply to You can assign a single port number apo here or assign a range of port numbers by assigning anaes the first port number and the last port number of the g range The two numbers are separated by a dash for example 101 150 means from port number 100 to port number 150 the range of 50 port numbers Enter the remote IP address range of the packets that Remote IP this rule will apply to If you assign 192 168 2 3 Address 192 168 2 5 it means 3 IP addresses 192 168 2 3 192 168 2 4 and 192 168 2 5 Remote Port Range Enter the remote port range of the packets that this rule will apply to You can assign a single port number here or assign a range of port numbers by assigning the first port number and the last port number of the range The two numbers are separated by a dash for example 101 150 means from port number 101 to port number 150 which
73. nection tracking MMS Support for Microsoft Streaming Media Services protocol Quake3 Support for Quake Ill Arena connection tracking and nat Talk Allows netfilter to track talk connections TFTP Support for TFTP IPsec Support for IPsec passthrough O Starcraft Support for Starcraft Battle net game protocol O MSN Support for MSN file tranfer ran Support for PPTP passthrough Parameters Default Description You can enable Application Layer Gateway function and the router will let selected application correctly pass though the NAT gateway Enable Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 82 2 7 6 Static Routing This router provides static routing function when NAT is disabled With static routing the router can forward packets according to your routing rules The IP sharing function will not work any more in static routing mode Note The DMZ function of firewall will not work if static routing is enabled NAT 2 NAT Network Address Translation allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses NAT provides Firewall protection from hacker attacks and has the flexibility to allow you to map Private IP Addresses to Public IP Addresses for key services such as the Web or FTP NAT Module O Enable Disable APPLY
74. nection will be dropped and use 3G 3 5G wireless connection instead If 3G 3 5G wireless signal reception is poor and the connection can not be restored within 60 seconds 3G 6200n will use wired Internet connection again and will not switch back to wireless Internet connection This only happens with wired Internet connection is available If wired connection is unavailable 3G 6200n will try to establish 3G 3 5G wireless connection again and again If you want to use 3G 3 5G wireless connection again you need to remove 3G 3 5G modem card from 3G 6200n and reconnect it back after 5 seconds A Plug and play no setup procedure required Connect the USB 3G 3 5G modem card with 3G 6200n and make sure the corresponding USB LED indicator of 3G 6200n lights up then you can use the web browser to access Internet 47 B PIN code or user name password required Please check the authentication method you want to use Most of telecomm service providers require you to input PIN Code please check SIM and input the PIN code provided by telecomm service provider Most of options listed here are optional and you don t have to provide those information if telecomm service provider doesn t provide you with those information If telecomm provider provides you with username password please check User Name Password box and input the user name password provided by telecomm service provider then click APPLY button Wait for 1 min
75. nternet Service 36 3 56 Only UMTS HSPA HSDPA Note Please choose CDMA if your ISP use 3G CDMA system Service CDMA v 20 C Driver Utility required on PC side Some 3G 3 5G modem card does not work with instructions A or B listed above ex BandLuxe C100S You need to install 3G 3 5G modem card driver utility on every PC which needs to access Internet first After driver utility installation is complete every PC will be able to access Internet via 3G 6200n 1 Plug in the BandLuxe C100S modem card to the USB port of your computer 2 The system will detect the hardware of C100S USB adapter and also the storage inside the adapter Found New Hardware i Found New Hardware BandLuxe 3 56 HSDPA Adapter 3 Please click Cancel to ignore the message of the found new hardware wizard Found New Hardware Wizard Welcome to the Found New Hardware Wizard Windows will search for current and updated software by looking on your computer on the hardware installation CD or on the Windows Update Web site with your permission Can Windows connect to Windows Update to search for software O Yes this time only Yes now and every time connect a device O No not this time Click Next to continue Cancel 21 4 Please go to My computer you will see the BandLuxe C100S Double click the device Other Places Local Disk C lt Image
76. o enable the protection mechanism This mechanism can decrease the rate of data collision between 802 11b and 802 11g wireless stations When the protection mode is enabled the throughput of the AP will be a little lower due to many of frame traffic will be transmitted CTS Protect You can adjust the wireless transmit power here By Tx Power reduce the TX power you can reduce the wireless coverage to make it only cover the area you need WMM stands for Wi Fi Multimedia lt is a standard created to define quality of service QoS in Wi Fi networks This adds prioritized capabilities to Wi Fi WMM networks and optimizes their performance when multiple concurring applications each with different latency and throughput requirements compete for network resources Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 59 2 5 3 Security This Router provides complete wireless LAN security functions include WEP IEEE 802 11x IEEE 802 11x with WEP WPA with pre shared key and WPA with RADIUS With these security functions you can prevent your wireless LAN from illegal access Please make sure your wireless stations use the same security function 2 5 3 1 WEP only When you select 64 bit or128 bit WEP key you have to enter WEP keys to encrypt data You can generate the key by yourself and enter it You can enter four WEP keys an
77. olve the problem Only one Internet connection wireless wired can be used at the same time Wireless connection 3G 3 5G will be selected first and use wired Internet connection as backup Therefore please DO NOT connect your 3G 3 5G modem card with 3G 6200n or your telecomm service provider may charge you with high communication fee For example if you connect 3G 3 5G modem card with 3G 6200n when you re using wired Internet connection wired connection will be dropped and use 3G 3 5G wireless connection instead If 3G 3 5G wireless signal reception is poor and the connection can not be restored within 60 seconds 3G 6200n will use wired Internet connection again and will not switch back to wireless Internet connection This only happens with wired Internet connection is available If wired connection is unavailable 3G 6200n will try to establish 3G 3 5G wireless connection again and again If you want to use 3G 3 5G wireless connection again you need to remove 3G 3 5G modem card from 3G 6200n and reconnect it back after 5 seconds A Plug and play no setup procedure required Connect the USB 3G 3 5G modem card with 3G 6200n and make sure the corresponding USB LED indicator of 3G 6200n lights up then you can use the web browser to access Internet B PIN code or user name password required Please check the authentication method you want to use Most of telecomm service providers require you to input PIN Code please check
78. ond Select Telstra Big Pond if your ISP requires the Telstra Big Pond protocol to connect you to the Internet Your ISP should provide all the information required in this section Telstra Big Pond protocol is used by the ISP in Australia 38 Telstra Big Pond If your Internet service is provided by Telstra Big Pond in Australia you will need to enter your information below This information is provided by Teistra BigPond O Assign login server manually Server IP Address Parameter Description User Name _ Enter the User Name provided by your ISP for the Telstra Big Pond connection Password Enter the Password provided by your ISP for the Telstra Big Pond connection User decide Select if you want to assign the IP of Telstra Big login server __ Pond s login server manually manually Login Server The IP of the Login Server Click lt OK gt when you have finished the configuration above Congratulations You have completed the configuration for the Telstra Big Pond connection You can start using the router now if you wish to use some of the advance features supported by this router see chapter 2 3 4 Chapter 2 General Settings Once you click on the General Setup button at the Home Page you should see the screen below If you have already configured the Quick Setup Wizard you DO NOT need to configure anything thing in the General Setup screen for you to start using
79. ort numbers Application Protocol Port Number Telnet TCP 23 110 FTP TCP 21 SMTP TCP 25 POP3 TCP 110 H 323 TCP 1720 SNMP UCP 161 SNMP Trap UDP 162 HTTP TCP 80 PPTP TCP 1723 PC Anywhere TCP 5631 PC Anywhere UDP 5632 PPPoE Point to Point Protocol over Ethernet Point to Point Protocol is a secure data transmission method originally created for dial up connections PPPoE is for Ethernet connections PPPoE relies on two widely accepted standards Ethernet and the Point to Point Protocol It is a communications protocol for transmitting information over Ethernet between different manufacturers Protocol A protocol is a set of rules for interaction agreed between multiple parties so that when they communication with each other based on such a protocol the interpretation of their behavior is well defined and can be made objectively without confusion or misunderstanding Router A router is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses Subnet Mask A subnet mask which may be a part of the TCP IP information provided by your ISP is a set of four numbers e g 255 255 255 0 configured like an IP address It is used to create IP address numbers used only within a particular network as opposed to valid IP address numbers recognized by the
80. r dose not work The router can also take Daylight savings into account If you wish to use this function you must check tick the enable box to enable your daylight saving configuration below Daylight Savings Select the period in which you wish to start using times From daylight saving Select the period in which you wish to stop using Mmeo daylight saving Click on NEXT to proceed to the next page step 2 Broadband Type Step 2 3G 3 5G Internet Configuration 3G 6200n supports most of 3G 3 5G modem cards just connect the modem card to the USB port of 3G 6200n and 3G 6200n will recognize it automatically no additional setup procedure required However some of modem cards require PIN code or account password you have to use 3G 6200n s web interface to input these information and some modem cards requires you to connect the modem card with your PC and install driver utility before you connect it with 3G 6200n all PCs which need to access Internet by 3G 6200n requires to perform this procedure once If you still not able to connect to Internet please use wired Internet connection to access our website http www edimax com download latest version of firmware and upgrade 3G 6200n s firmware If you still not be able to get connected by your 3G 3 5G modem card please contact your dealer of purchase and provide the model name of the 3G 3 5G modem card you have we ll try our best to help you to s
81. r number is called In most but not all areas the sum of the REN of all devices connected to one line should not exceed five 5 0 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company to determine the maximum REN for your calling area If the modem causes harm to the telephone network the telephone company may discontinue your service temporarily If possible they will notify you in advance But if advance notice isn t practical you will be notified as soon as possible You will be advised of your right to file a complaint with the FCC The telephone company may make changes in its facilities equipment operations or procedures that could affect the proper operation of your equipment If they do you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service If you experience trouble with this modem please contact your dealer for repair warranty information The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not malfunctioning This equipment may not be used on coin service provided by the telephone company Connection to party lines is subject to state tariffs Installation This device is equipped with a USOC RJ11C connector FCC Part 15 This equipment has been tested and found to comply wit
82. rnnnnnrrnnnnnnnnnncnnnnnnn 43 2 1 3 Remote MAN AO ME NIN ISS 45 O O AE 47 A Plug and play no setup procedure required oooooooccccccccccnoncnoncccccncncncnanannne 47 B PIN code or user name password required oooooococcccccccccncconaccccncnnncnannnnns 48 PRONTA O 48 A seers teas te pe a sara TE Ra sada Sedu ed ahead aaa 49 2 3 2 Static IP Address isos 50 2 3 3 PPPoE PPP over Ethernet tii a AAA ea 50 O A E I EATE AE AN 50 2 3 5i A a E E E 50 235 Telstra BIO PONU io e a a ai 50 AAN SiO 51 2 DING nated ta A O OA 51 AMAN OA AAN do 53 A O E 55 A Se Aen a E ee See eet ee E ees 56 2 5 2 Advanced SCUINGS cons sio iia csi sia isthe lately 58 25 3 OUT MG sR tae ian A Ned nde dated Se ey ce Aad Sete das Seabee ddas tA Senos 60 NS A PREC HPT COCHIN AEAEE AAE EEEE EARE SEEEN AAEN iai 60 DI 802 IX OMV aaae e e A A A A a 62 25 3 3 8021X WEP St tic a E E een ac eee 63 2 5 3 4 WPA Pre shared Kitade 64 225 Access CONO anna na 65 OO A E 69 AN eevee cece cite tect Se eas ce es SR eR ea Se a aR eae SR RRO ee 72 2 ofl POP FO IN ii o 74 ES A A AA AA SE 76 2 7 3 Special Applications ooooonnnnncccccnnnnnnncnnonnnncccnnnnnnnnnnnnnnnnncnnnnnnnnnnnnnnnnnccnncnnnnn 78 2 7 4 UPnP OTN OS iaa 81 NS O O 82 2 10 Static FrOUMIIG rad aa 83 28 PARC Wall diorma coe sh aise uate taunted ett a Sete iat 85 2 8 1 ACCESS Control cccccccceeeeeeeeeeeeneeeeeeeeeeeeeeeeaaaeeeeeeeeeeesececeaeeeeeeeeeeeseeeeceeeeeeeeees 86 2 82 A O 86 2 8 3 DoS D
83. router 55 2 5 1 Basic Settings You can set parameters that are used for the wireless stations to connect to this router The parameters include Mode ESSID Channel Number and Associated Client This page allows you to define ESSID and Channel for the wireless connection These parameters are used for the wireless stations to connect to the Access Point pM Access Paint 2 4 GHz B G N Parameters Default 11 w APPLY CANCEL Description Mode It allows you to set the AP to AP Bridge or WDS mode Band It allows you to select the wireless band 802 11 B G N 802 11 B G 802 11b and or 802 11g You can select B G N mode to allow all 802 11b 802 11g and 802 11n clients to connect to this wireless access point ESSID Channel Number default This is the name of the wireless access point All devices in the same wireless LAN should have the same ESSID The wireless channel used by the wireless access point All devices in the same wireless LAN should use the same channel MAC address If you want to combine more than one network you have to set this access point to AP Bridge Point to Point mode AP Bridge Point to Multi Point mode or AP Bridge WDS mode You have to enter the MAC addresses of other access points which will join the same wireless network Set Security Click the Set Security button an
84. router s LINK LED is lit to confirm the cable connections are made correctly Getting started This is a step by step instruction on how to start using the router and get connected to the Internet 1 Setup your network as shown in the setup diagram above fig 1 2 2 You will need to set your LAN PC clients so that it can obtain an IP address automatically All LAN clients require an IP address Just like the mailing address in real world it allows LAN clients to find one another If you already configured your PC to obtain an IP automatically please jump to step 3 page 11 Configure your PC to obtain an IP address automatically Broadband router s DHCP function is switched on by default this means that you can obtain an IP address automatically once you ve configured your PC to obtain an IP address automatically This section will show you how to configure your PC s so that it can obtain an IP address automatically for either Windows 95 98 Me 2000 or NT operating systems For other operating systems Macintosh Sun etc follow the manufacturer s instructions The following is a step by step illustration on how to configure your PC to obtain an IP address automatically for 2a 2b 2c 2d Windows 95 98 Me Windows XP Windows 2000 and Windows NT A Sr e a 2a Windows 95 98 Me 1 Click the Start button and select Settings then click Control Panel The Control Panel window will appear 2 Double click Network icon
85. s LAN The authentication is processed by a RADIUS server This mode also uses WEP to encrypt the data during communication This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network WEP v Key Length Key Format Hex 10 Characters x Default Tx Key Key 1 vw Encryption Key 1 Le a Encryption Key 2 Encryption Key 3 Encryption Key 4 Enable 802 1x Authentication RADIUS Server IP Address RADIUS Server Port 11812 a __ 1812 Ll RADIUS Server Password APPLY CANCEL For detailed instructions of WEP settings please refer to section 2 4 3 1 WEP only For the 802 1x settings please refer to section 2 4 3 2 802 1x only 63 2 5 3 4 WPA Pre shared key Wi Fi Protected Access WPA is an advanced security standard You can use a pre shared key to authenticate wireless stations and encrypt data during communication It uses TKIP or CCMP AES to change the encryption key frequently So the encryption key will not be known by hackers easily and this will improve security This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network RA EMOS YVPATKIP OWPA2 AES OWPA2 Mixed Passphrase v Pre shared Key Format Pre shared K
86. s require multiple connections such as Internet games video conferencing Internet telephony and others In this section you can configure the router to support multiple connections for these types of applications Special Applications 2 Some applications require multiple connections such as Internet gaming video conferencing Internet telephony and others These applications cannot work when Network Address Translation NAT is enabled If you need to run applications that require multiple connections specify the port normally associated with an application in the Trigger Port field select the protocol type as TCP or UDP then enter the public ports associated with the trigger port to open them for inbound traffic Note The range of the Trigger Port is 1 to 65535 CI Enable Special Applications IP Address TCP Port to Open UDP Port to Open 0000 BE Select v Popular Applications Select Game v Add e Current Trigger Port Table Here are descriptions of every setup items Item Name Description Enable Check this box to enable support for special applications and uncheck this box to disable this support IP Address Input the IP address of the computer which is going to use the special application Computer name All computer names found by this broadband router on local network will be listed here You can select the computer name and click lt lt b
87. se make sure this function can work properly when you use this function in the first time especially your ISP charge you by time used Click lt OK gt when you have finished the configuration above Congratulations You have completed the configuration for the PPTP connection You can start using the router now if you wish to use some of the advance features supported by this router see chapter 2 3 4 1 5 L2TP Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet Your ISP should provide all the information required in this section e WAN Interface Settings Obtain an IP Address Automatically Host Name Use The Following IP Address IP Address Default Gateway TOO e L2TP Settings Password L2TP Gateway ESA 000000000000 Clone MAC Teme eee Continuous CTA 10 1 1000 Minute Connect sconnect BACK Parameter Description Obtain an IP The ISP requires you to obtain an IP address by address MAC Address DHCP automatically before connecting to the L2TP server Your ISP may require a particular MAC address to connect to the Internet This MAC address is the PC s MAC address that you originally made your Internet connection Type in this MAC address in this section or use the Clone MAC Address button to replace the WAN MAC address with the MAC address of that PC you have to be using that
88. sical Address 00 50 FC FE 02 DB in this example 108 Glossary Default Gateway Router Every non router IP device needs a default gateway When the device sends out an IP packet if the destination is not in the same network the device will send the packet to default gateway which will then forward it to the destination DHCP Dynamic Host Configuration Protocol This protocol automatically assigns an IP address for every computer in your network DNS Server IP Address DNS stands for Domain Name System which allows Internet servers to have a domain name such as www Broadbandrouter com and one or more IP addresses such as 192 34 45 8 A DNS server will maintain a database of domain names and respective IP addresses so when a domain name is requested like typing Broadbandrouter com in your Internet browser the user will get the corresponding IP address The DNS server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to you DSL Modem DSL stands for Digital Subscriber Line A DSL modem uses your existing phone lines to transmit data at high speeds Ethernet A kind of standard of computer networks Ethernet networks are connected by special cables and hubs and transfers data at up to 10 100 million bits per second Mbps Idle Timeout Idle timeout is designed so that after no traffic has been transferred to the Internet for a pre configured amount of time
89. t MTU lt 1492 AAA Continuous he Idle Time Out 1 1000 Minute BACK Parameter Description Enter the User Name provided by your ISP for the PPPoE connection User Name Enter the Password provided by your ISP for the Password PPPoE connection This is optional Enter the Service name of your ISP SENE Name when your ISP requires it otherwise leave it blank This is optional You can specify the maximum size of your transmission packet to the Internet Leave it as it is if you to not wish to set the maximum packet size Please ask your ISP for detailed information MTU If you select Continuous the router will maintain the connection to the ISP If the WAN connection drops the router will reconnect to the ISP automatically Connection Type If you select Connect On Demand the router will auto connect to the ISP when someone wants to use the Internet and keep connected until the WAN idle timeout The router will drop the WAN connection if the time period that no one is using the 32 Internet exceeds the Idle Time If you select Manual the router will connect to ISP only when you click Connect manually from the Web management interface The WAN connection will not disconnect because of idle timeout If the WAN line drops and connected at a latter time again the router will not connect to the ISP by itself Idle Time Yo
90. tion Select the time zone of the country you are living Sel ime Zone The router will set its time based on your selection Time Server The router default the Time Server Address is Address 192 43 244 18 The router can also take Daylight savings into account If you wish to use this function you must check tick the enable box to enable your daylight saving configuration below Daylight Savings Times From _ Select the period in which you wish to start using daylight Saving Times to Select the period in which you wish to stop using daylight Saving Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 2 1 2 Password Settings You can change the password required to log into the broadband router s system web based management By default there is no password So please assign a password to the Administrator as soon as possible and store it in a safe place Passwords can contain 0 to 12 alphanumeric characters and are case sensitive Password Settings 2 You can change the password required while logging into the wireless router s web based management system By default the password is 1234 So please assign a password to the Administrator as soon as possible and store it in a safe place Passwords can contain DO to 30 alphanumeric characters and are case sensitive Current Password New
91. u can specify an idle time minutes for the WAN port This means if no packets have been sent no one using the Internet during this specified period the router will automatically disconnect the connection to your ISP Note This idle timeout function may not work due to abnormal activities of some network application software computer virus or hacker attacks from the Internet For example some software sends data to the Internet in the background even when you are not using the Internet So please turn off your computer when you are not using it This function also may not work with some ISP So please make sure this function can work properly when you use this function in the first time especially when your ISP charge you by the connection time Click lt OK gt when you have finished the configuration above Congratulations You have completed the configuration for the PPPoE connection You can start using the router now if you wish to use some of the advance features supported by this router see chapter 2 3 4 33 1 4 PPTP Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet Your ISP should provide all the information required in this section PPTP Point to Point Tunneling Protocol is a common connection method used in xDSL connections e WAN Interface Settings Obtain an IP Address Automatically _ TRA OOOO00000000 Clone MAC Use The Following IP Address Subnet Mask
92. u ve configured in the Quick Setup Wizard General Setup section Device Status 2 View the current setting status of this device Wireless Configuration Access Point default Channel Number 11 LAN Configuration SAA Disable eC it ee 192 168 2 1 TA ESA 255 255 255 0 ASA Enable ANA 00 1 1f 1f 74 50 Parameters Description Device Status This page shows the broadband router s current device settings including broadband router LAN port s current LAN IP address and subnet mask It also shows whether the DHCP server function is enabled disabled 98 3 3 System Log View the operation log of the system System Log View the system operation information You can see the system start up time connection process etc here 00 00 00 none syslog info syslogd started BusyBox v1 00 pre2 200 08 23 40 none daemon info in rdiscd 1929 224 0 0 2 rdisc St 08 23 40 none daemon info in rdiscd 1929 O packets transmitted 08 23 40 none daemon info in rdiscd 1929 O packets received 08 23 40 none daemon info in rdiscd 1929 Jan Now Nov Nov Nov oom oe a lv Parameters Description This page shows the system log of the broadband router It displays any event occurred after system start up At the bottom of the page the system log can be saved lt Save gt as a local file you can clear the log by click lt Clear gt button too You can also click
93. ult tool to force the Wireless Router to perform System Reset and restore the original factory settings Backup Settings 6 Restore to Factory Default Parameters Description Use the Backup tool to save the broadband router s current configuration to a file named config bin on your PC You can then use the Configuration Restore tool to restore the saved configuration to Tools the broadband router Alternatively you can use the Restore to Factory Defaults tool to force the broadband router to perform a power reset and restore to original factory settings 4 2 Firmware Upgrade This page allows you to upgrade the router s firmware Firmware Upgrade 2 This tool allows you to upgrade the Wireless Router s system firmware Enter the path and name ofthe upgrade file and then click the APPLY button below You will be prompted to confirm the upgrade The system will automatically reboot the router after you finished the firmware upgrade process If you dont complete the firmware upgrade process in the next step you have to reboot the router NEXT 104 Firmware Upgrade 2 This tool allows you to upgrade the Wireless Router s system firmware Enter the path and name of the upgrade file and then click the APPLY button below You will be prompted to confirrn the upgrade Browse APPLY CANCEL Parameters Description This tool allows you to upgrade the broadband ro
94. ur LAN client s IP address when this time period is reached IP Address Pool You can select a particular IP address range for your DHCP server to issue IP addresses to your LAN Clients Note By default the IP range is from 192 168 2 100 to 192 168 2 200 If you want your PC to have a static fixed IP address then you ll have to choose an IP address outside this IP address Pool Domain Name You can specify a Domain Name for your LAN Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the router 54 2 5 Wireless Wireless Access Point builds a wireless LAN and can let all PCs equipped with IEEE 802 11b or 801 11g wireless network adaptor connect to your Intranet It supports WEP and WPA2 encryption to enhance the security of your wireless network Wireless 2 The Wireless Router can be quickly configured as a wireless access point for roaming clients by setting the access identifier and channel number It also supports data encryption and client filtering Wireless Module Enable Disable Parameters Default Description Enable or You can select to enable or disable the disable wireless access point module of this router Wireless Enable module function Click lt Apply gt at the bottom of the screen to save the configurations You can now configure other advance sections or start using the
95. ute for 3G 6200n to reboot 3G 3 5G Your service provider settings will be detected automatically Ifthe settings are not the same as defaults please enter the Authentication Method User Name Password APN PIN Code and Dialed Number provided to you by your ISP in the appropriate fields e Network Settings User Name Password PIN Code Il internet Dialed Number 90 Advanced PPP Settings Username Password 3G 3 5G Only UMTS HSPA HSDPA Idle Timeout fil Echo Timeout 60 Echo Count fE Apply O a 3 D pa 2 3 WAN Use the WAN Settings screen if you have already configured the Quick Setup Wizard section and you would like to change your Internet connection type The WAN Settings screen allows to specify the type of WAN port connect you want to establish with your ISP The WAN settings offer the following selections for the router s WAN port Dynamic IP Static IP Address PPPoE PPTP L2TP Telstra Big Pond DNS and DDNS WAN The Wireless Router can connect to your Internet Service Provider with the following methods Dynamic IP died an IP Address automatically from your Service j Uses a Static IP Address Your Serice Provider gives 9 sate a Static IP Address to access Internet services PPF over Ethernet is a common connection method O PPPoE used in xDSL conn
96. uter s system firmware To upgrade the firmware of your broadband router you need to download the firmware Firmware file to your local hard disk and enter that file name and Upgrade path in the appropriate field on this page You can also click the browse button to locate the firmware file on your PC After you selected the new firmware file click lt Apply gt at the bottom of the screen to start the upgrade process You may have to wait few minutes for the upgrade to complete Once the upgrade is complete you can start using the router Warning When upgrading firmware be sure not to switch the computer off or restart your computer 4 3 Reset You can reset the router s system when there s something wrong with the router The reset function will reboot your router Reset 2 In the event that the system stops responding correctly or stops functioning you can perform a Reboot Your settings will not be changed To perform the reboot click on the APPLY button below You will be asked to confirm your decision The Reboot will be complete when the LED Power light stops blinking 3 11 2009 9 48 15 APPLY 105 Parameters Description In the event that the system stops responding or stops functioning you can perform a reset Your settings will not be changed To perform the reset Reset click on the lt APPLY gt button You will be asked to confirm your decision The reset will be complete when the pow
97. utton to add selected computer s IP address to IP Address field Please note that this list may not be able to list all computers on your local network TCP Port to Open Input the TCP port number required by the special 78 application the port number can be a single value or a range like 20 50 If you need to input more than one port number and they re not contiguous list all port numbers here and separate them by comma If the application does not use TCP port leave it blank UDP Port to Open Input the UDP port number required by the special application the port number can be a single value or a range like 20 50 If you need to input more than one port number and they re not contiguous list all port numbers here and separate them by comma If the application does not use UDP port leave it blank Comment You can input any text here to help you remember the purpose of this item This is optional Select Game This router comes with a numerous port mapping settings of network games If the game you wish to set is listed here you can select it from dropdown menu After a game is selected click Add the one next to Select Game dropdown list to add the connection parameters to all respective fields Add Click this button to add a new port mapping rule to special applications table Reset Click this button to remove all values in every field
98. ve been provided with this information choose this option and enter the assigned IP Address Subnet Mask Gateway IP Address and DNS IP Address for your Wireless Router PPPoE xDSL If you connect to the Internet using an xDSL Modem and your ISP has provided you with a Password and a Service Name then your ISP uses PPPoE to establish a connection You must choose this option and enter the required information PPTP xDSL If you connect to the Internet using an xDSL Modem and your ISP has provided you with a Password Local IP Address Remote IP Address and a Connection ID then your ISP uses PPTP to establish a connection You must choose this option and enter the required information O L2TP xDSL Menu Description Cable Modem Your ISP will assign you with an IP address automatically Fixed IP xDSL Your ISP gave you an IP address already PPPoE xDSL Your ISP requires you to use Point to Point Protocol over Ethernet PPPoE PPTP xDSL Your ISP requires you to use a Point to Point Tunneling Protocol PPTP L2TP xDSL Your ISP requires you to use a Layer Two Tunneling Protocol L2TP Telstra Big Pond This Protocol only used for Telstra Big Pond Internet service in Australia 29 Click on one of the WAN type and then proceed to the manual s relevant sub section 1 1 1 2 1 3 1 4 1 5 or 1 6 Click on Back to return to the previous screen 1 1 Cable Modem Choose Cable Modem i
99. ver You can have different services e g email FTP Web etc going to different service servers clients in your LAN The Virtual Server allows you to redirect a particular service port number from the Internet WAN Port to a particular LAN IP address and its service port number Some applications require multiple connections such as Internet games video conferencing Internet A ee telephony and others In this section you can PP configure the router to support these types of applications UPnP Setting It allows to enable or disable UPnP feature here After you enable the UPnP feature all client systems that 72 NAT Network Address Translation allows multiple users at your local site ta access the Internet through a single Public IP Address or multiple Public IP Addresses NAT provides Firewall protection from hacker attacks and has the flexibility to allow you to map Private IP Addresses to Public IP Addresses for support UPnP like Windows XP can discover this router automatically and access the Internet through this router without any configuration The NAT Traversal function provided by UPnP can let applications that support UPnP smoothly connect to Internet sites without any incompatibility problem due to the NAPT port translation ALG Setting You can let special applications that require Application Layer Gateway to be supported here Static Routing You can disable NAT funct
100. wall The Firewall section allows you to configure Access Control Hacker Prevention and DMZ Select one of the above General Setup selections and proceed to the manual s relevant sub section 41 2 1 System The system screen allows you to specify a time zone to change the system password and to specify a remote management user for the broadband router System This page includes the basic configuration tools for the Wireless Router s remote management access function Parameters Description TimeZone Select the time zone of the country you are living The router will set its time based on your selection Password Allows you to define a password in order to access Settings the web based management website Remote You can specify a Host IP address that can perform Management remote management functions Select one of the above three system settings selections and proceed to the manual s relevant sub section 42 2 1 1 Time Zone The Time Zone allows your router to reference or base its time on the settings configured here which will affect functions such as Log entries and Firewall settings Time Zone 2 Set the time zone ofthe Wireless Router This information is used for log entries and firewall settings GMT 00 00 Greenwich Mean Time Dublin Edinburgh Lisbon London 192 43 244 18 Cl Enable Time From To Daylight Savings APPLY CANCEL Parameter Descrip
101. want to remove in the table rules from land then click Delete If you want to remove all QoS table rules from the table just click Delete All button Click Reset will clear your current selections Select the rule you want to edit and click Edit then Edita QoS the detailed information of the selected QoS rule will rule appear Click Apply after editing the form and the rule will be saved Adiust QoS You can select the rule and click Move Up to make E iani its priority higher You also can select the rule and p Y click Move Down to make its priority lower Edit QoS Rule You can assign packet classification criteria by its local IP range remote IP range traffic type protocol local port range and remote port range parameters The parameters you leave blank will be ignored The priority of this rule will be applied to packets that match the classification criteria of this rule You can limit bandwidth consumed by packets that match this rule or guarantee bandwidth required by packets that match this rule 12 os This page allows users to add modify the QoS rule s settings Remote IP Address Remote Port Range Local IP Address Local Port Range Rule Name Bandwidth Download Kbps Guarantee Y None Y TCP Traffic Type Protocol 70 Parameters Descriptio
102. will maintain the connection to the ISP If the WAN line breaks down and links again at a latter time the router will reconnect to the ISP automatically if you select Connect On Demand the router will auto connect to the ISP when someone wants to use the Internet and keep connected until the WAN idle timeout The router will close the WAN connection if the time period that no one is using the Internet exceeds the Idle Time If you select Manual the router will connect to ISP only when you click Connect manually from the Web management interface The WAN connection will not be disconnected because of idle timeout If the WAN line breaks down and got connected again at a latter time the router will not connect to the ISP by itself Idle Time You can specify an idle time threshold minutes for the WAN port This means if no packets has been sent no one using the Internet throughout this specified period then the router will automatically disconnect the connection to your ISP Note This idle timeout function may not work due to abnormal activities of some network application 35 software computer virus or hacker attacks from the Internet For example some software sends network packets to the Internet in the background even when you are not using the Internet So please turn off your computer when you are not using it This function also may not work with some ISP So plea
103. xed IP xDSL if your ISP has given you a specific IP address for you to use Your ISP should provide all the information required in this section Static IP Enter the IP Address Subnet Mask Gateway IP Address and DNS IP Address provided to you by your ISP in the appropriate fields eee teem 172 1 1 1 Rae eae 255 255 0 0 DNS Address Default Gateway 172 1 1 254 Parameters Description IP address This is the IP address that your ISP has given you Subnet Mask Enter the Subnet Mask provided by your ISP e g 255 255 255 0 DNS address This is the ISP s DNS server IP address Gateway IP This is the ISP s IP address gateway address Click lt OK gt when you have finished the configuration above Congratulations You have completed the configuration for the Fixed IP x DSL connection You can start using the router now if you wish to use some of the advance features supported by this router see chapter 2 3 1 3 PPPoE Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet Your ISP should provide all the information required in this section PPPoE Enter the User Name and Password required by your ISP in the appropriate fields If your ISP has provided you with a Service Mame enter it in the Service Name field otherwise leave it blank User Name Password Service Name OLUE 11392 512 l
104. your PC to obtain an IP address automatically please proceed to Step 3 2b Windows XP 1 Click the Start button and select Settings then click Network Connections The Network Connections window will appear 2 Double click Local Area Connection icon The Local Area Connection window will appear 3 Check your list of Network Components You should see nternet Protocol TCP IP on your list Select it and click the Properties button 4 In the Internet Protocol TCP IP Properties window select Obtain an IP address automatically and Obtain DNS server address automatically as shown on the following screen Internet Protocol TCP IP Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask pour network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address ally Use the following DNS server addresses 5 Click OK to confirm the setting Your PC will now obtain an IP address automatically from your Broadband Router s DHCP server Note Please make sure that the Broadband router is the only DHCP server on your LAN Once you ve configured your PC to obtain an IP address automatically please proceed to Step 3 2c Windows 2000 1 Click the Start button and select Settings then click Control Panel The Control Panel window will appear 2 Double cl

Edimax 3G-6200n 11n Wireless 3G Broadband Router

Contents

Download Pdf Manuals

Related Search

Related Contents