Philips goLITE BLU energy light HF3331
Contents
1. For the best results place the goLITE BLU at the same level as your midriff stomach area e g place it on the table at which you are sitting Note Do not stare into the light of the LED panel It is sufficient that the blue light reaches your eyes indirectly from the side Use your goLITE BLU in a well lit room to minimize eye strain Setting the clock Press the on off button briefly to turn on the appliance Fig 6 D The touchscreen display goes on Press the alarm button and the timer button simultaneously for 2 seconds Fig 7 D The clock time starts to flash on the display Fig 8 Set the clock time with the plus or minus button If you keep the button pressed the time moves forward or backward quickly Fig 9 To switch between the 12 hour a m p m and 24 hour time indication press the timer button and minus button simultaneously for 2 seconds Press either the alarm button or the timer button or wait 10 seconds to exit the time setting mode Setting the timer You can use the timer function to set the light time Press the on off button briefly to turn on the appliance Fig 6 D The touchscreen display goes on Press the timer button Fig 10 14 ENGLISH D The timer on indication and the timer countdown time start to flash Fig 11 Press the plus or minus button to set the session time If you keep the button pressed the time moves forward or backward quickly Fig 9 You can set a2. ELECTROMAGNETIC IMMUNITY The goLITE BLU is intended for use in the electromagnetic environment specified below The customer or the user of the goLITE BLU should make sure it is used in such an environment Immunity IEC 60601 Test Test LeveL Conducted 3 Vrms RF 150 kHz to IEC 61000 80 MHz 46 3V m Radiated 80 MHz to RF 2 5 GHz IEC 61000 4 3 COMPLIANCE LeveL ELECTROMAGNETIC ENVIRONMENT GUIDANCE Portable and mobile RF communications equipment should be used no closer to any part of the goLITE BLU including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance d 1 2 P d 1 2 d 2 3WN Where P is the maximum output power rating ofthe transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey a should be less than the compliance level in each frequency range b Interference may occur in the vicinity of equipment marked with the following symbol NOTE 1 At 80 MHz and 800 MHz the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people a Field strengths from fixed transmitters such as base stations f
3. differential mode 2 kV common mode lt 5 U gt 95 dip in U or 0 5 cycle 40 U 60 dip in U or 5 cycles 70 U 30 dip in U or 25 cycles lt 5 U gt 95 dip in U or 5 sec COMPLIANCE LeveL 2 4 6 KV contact 2 4 8 kV air 2 kV for power supply lines 1 kV for input output lines 1kV differential mode 2 kV for common mode lt 5 U gt 95 dip in U for 0 5 cycle 40 U 60 dip in U for 5 cycles 70 U 30 dip in U for 25 cycles lt 5 U gt 95 dip in U for 5 sec ELECTROMAGNETIC ENVIRONMENT GUIDANCE Floors should be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment If the user of the goLITE BLU requires continued operation during power mains interruptions it is recommended that the goLITE BLU be powered from an uninterruptible power supply or a battery Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment the a c mains voltage prior to application of the test level ENGLISH 27 GUIDANCE AND MANUFACTURER S DECLARATION
4. get as much of this light in the fall and winter and indoor light does not emit enough of this essential color The goLITE BLU energy light helps to deliver the wavelength color and intensity of light that we see in summer General description Fig 1 LED panel Socket for appliance plug Interactive touchscreen display arm touchscreen button arm chime indication arm light indication mer on indication lock time emo mode indication harge indication us touchscreen button imer touchscreen button 10 Timer countdown time Alarm time 11 Intensity indication 12 Minus touchscreen button D Small plug E Adaptor F Stand G Reset button ZOVOTI2 gt gt gt 0 0 OU AIN py ENGLISH 11 H Stand storage cavity Cover of built in rechargeable battery J J On off button Not shown Pouch Preparing for use It is very important that you know how long and how often you should use your Philips goLITE BLU energy light This knowledge can mean the difference between successfully responding to light and not responding at all Visit www lighttherapy com for a free assessment and to customize a ight therapy schedule just for you When to use the goLITE BLU energy light nowing what time to use the goLITE BLU energy light can mean the difference between feeling better in just a few days instead of weeks or perhaps not responding at all Follow these guidelines to understand how ight can boost mood and energy an
5. Always here to help you Register your product and get support at www philips com welcome HF3332 HF3331 PHILIPS PHILIPS ENGLISH LEEEJHTELEAH IMPORTANT SAFETY INSTRUCTIONS Read all warnings and cautions before you use your goLITE BLU energy light Observe these safety instructions to avoid potential hazards that could result in personal injuries or damage to your goLITE BLU energy light Warnings a warning indicates the possibility of injury to the user or operator Use the goLITE BLU energy light in vertical position with the stand in place in the recess on the back of the unit Do not use this appliance aying flat in horizontal position without the stand Do not expose the appliance to rain or moisture Do not use the appliance near a water source while bathing while washing hands or while you are in contact with water If you suffer from an eye disease or have a history of eye disease in your family consult your ophthalmologist before you use this appliance If you are experiencing any temporary eye problems wait until the problems are resolved before using this appliance Light emitted by this appliance may interact with photosensitizing medications Be sure to review all medications that you are currently aking with your doctor before using this appliance As with any bright light source do not stare into the appliance Do not use this appliance where the light might comprom
6. Do not use the goLITE BLU within two hours of your desired bedtime or you may not be able to fall asleep Charging Note You can also use the appliance while it is charging The goLITE BLU energy light comes with a 9 5V AC DC adaptor that operates on voltages ranging from 100 to 240 volts to allow worldwide use The adaptor comes with a set of exchangeable adaptor plugs that fit most common worldwide wall outlets model HF3331 only Put the adaptor in the wall outlet Insert the appliance plug into socket on the appliance Fig 2 DB Only the outline of the charge indication is visible D As the battery charges the four bars of the charge indication flash one by one and fill as the charge increases D When the battery is fully charged the charge indication stops flashing Note Charge the goLITE BLU at least 8 hours before you use it for the first time Charging normally takes 3 to 4 hours Note When the battery is fully charged it contains enough energy for 3 to 5 sessions Installation Remove the stand from the stand storage cavity Fig 3 Insert the bevelled end of the stand into the hole on the back of the appliance Magnets hold the stand in place Fig 4 ENGLISH 13 Place the goLITE BLU approximately 20 30 in 50 70cm from your eyes in such a way that the light bathes your face from the side Fig 5 You can read eat work at the computer watch TV or exercise while you use your goLITE BLU energy light
7. TE BLU is suitable Weight 0 4kg less than 14 ounces CISPR 11 for use in all establishments including domestic Harmonic emissions Class A a gt da Circuit diagrams component part lists and other technical descriptions IEC 61000 3 2 parda public low voltage power are available on request 3 a supply network that As user of this appliance you should take measures to prevent the Voltage fluctuations Flicker emissions Complies supplies buildings used for occurrence of electromagnetic interference or other types of interference ESS 3 domestic purposes between this appliance and other appliances Peak wavelength 468nm 8nm Half peak bandwidth 20nm Typical irradiance 100 intensity 30014 W cm 10 at 50cm 26 ENGLISH GUIDANCE AND MANUFACTURER S DECLARATION ELECTROMAGNETIC IMMUNITY The goLITE BLU is intended for use in the electromagnetic environment specified below The customer or the user of the goLITE BLU should make sure it is used in such an environment Immunity Test Electrostatic Discharge ESD IEC 61000 4 2 Electrical Fast Transient Burst IEC 61000 4 4 Surge IEC 61000 4 5 Voltage dips short interruptions and voltage variations on power supply input lines IEC 61000 4 11 Power frequency 50 60 Hz magnetic field IEC 61000 4 8 IEC 60601 Test LeveL 2 4 6 kV contact 2 4 8 KV air 2 kV for power supply lines 1 kV for input output lines 1 kV
8. To deactivate the demo mode press and hold the on off button for 10 seconds Using the appliance Use this appliance for its intended household use as described in this manual Press the on off button briefly to turn on the appliance Fig 6 D The touchscreen display goes on Note If you do not touch the display or press any button for 5 minutes when the display is turned on and the appliance operates on battery power the appliance turns off automatically to save battery power Note If you want to turn off the appliance press and hold the on off button for 2 seconds Briefly press the on off button again to turn on the LED panel D The timer counts down the set time Note The default session time is 15 minutes Use the timer to change the session time see section Setting the timer in chapter Preparing for use D When the countdown is finished the LED panel turns off automatically Note If you want to turn off the LED panel before the countdown is finished press the on off button briefly Press the plus or the minus button to change the light intensity Fig 9 You can increase or decrease the intensity in increments of 25 16 ENGLISH Pausing a session Press the on off button or press the minus button to reduce the intensity to 0 D The remaining minutes of the session are still shown on the display Press the on off button to continue the session or press any of the touchscreen buttons to end the
9. all UV light The goLITE BLU emits safe levels of blue light according to current standards However if you suffer from an eye disease or have a history of eye disease in your family consult your ophthalmologist before you use the goLITE BLU If you have a temporary eye problem wait until it is resolved before you use he goLITE BLU The goLITE BLU energy light is safe if used according o the instructions The appliance is free from any ultraviolet light risk to the eye and it produces a safe diffused field of light The appliance has been tested for ocular safety As with any bright light source do not look into the light too long The beneficial reaction happens when he photoreceptors in the eye are stimulated Since hese photoreceptors lie in the periphery of the eye you get a better result if you place the goLITE BLU at a slight angle to your face ENGLISH 21 Question Answer Should use the goLITE BLU every day Can the light cause harm to children or pets Can use the goLITE BLU more than once a day How long do the LEDs last What if one or more LEDs stop working prematurely You can use the goLITE BLU energy light daily especially during the winter months Many people find that they do not need the light in summer Others use it year round because they spend most of their time indoors and do not get the right kind of light signals to boost their mood and energy No The light i
10. any attachment not provided with the product NO RESPONSIBILITY IS ASSUMED FORANY SPECIAL NCIDENTAL OR CONSEQUENTIAL DAMAGES In order to obtain warranty service simply call toll free 1 866 832 4361 n US Manufactured for Philips Consumer Lifestyle A Division of Philips Electronics North America Corporation RO Box 10313 Stamford CT 06904 n Canada Imported for Philips Electronics LTD 281 Hillmount Road arkham Ontario L6C 253 Trademarks owned by the Philips Group 2013 Koninklijke Philips Electronics N V All Rights Reserved Frequently asked questions This section lists the questions most frequently asked about the appliance If you cannot find the answer to your question call 1 866 832 4361 for assistance 20 ENGLISH Question Answer Do have to take off my glasses when use the goLITE BLU Does the appliance have any side effects Can get sunburn from using the goLITE BLU have heard that light can be dangerous Can the goLITE BLU damage my eyes No you can use the goLITE BLU energy light with your glasses on Do not wear tinted glasses or sunglasses when you use the goLITE BLU as these glasses reduce its effectiveness The goLITE BLU is safe if used according to the instructions Temporary headaches or nausea have been reported These effects are usually solved by sitting further away from the appliance No the technology used in the goLITE BLU eliminates
11. d when to use the goLITE BLU for he best results Duration and intensity ost people get beneficial results from 15 to 45 minutes of usage each day You can start using the goLITE BLU at 50 intensity and increase he light intensity if you feel no response after a week Timing Using the goLITE BLU energy light at any time of day directly affects your alertness You can use the goLITE BLU energy light as a light bath for the winter blues throughout the day The best time to use it is in the morning Do not use the goLITE BLU late in the evening If you use it within 2 hours of going to bed it could disrupt your sleep If you find it difficult to get up each day without an alarm clock or if you often sleep in you need morning light Use the goLITE BLU within the first hour or two after waking up If you find it difficult to stay awake in the late evening and wake up 00 early in the morning you need evening light Use the goLITE BLU before you start to feel drowsy 12 ENGLISH If mornings or evenings do not seem to be the problem but you feel generally tired during the day then the time at which you use the goLITE BLU is not as important You can use the goLITE BLU in the morning or around midday For example when you wake up in the morning use it for 15 to 30 minutes and then again at midday or in the evening for approximately the same amount of time Place the goLITE BLU further away from you during the evening session
12. e This resets the goLITE BLU and IEC 60601 1 classification clears its memory Insulation class Il Ingress of water IPXO 24 ENGLISH ENGLISH 25 Model HF3332 HF3331 EMC Information Mode of operation Continuous The goLITE BLU energy light should not be used adjacent to or stacked with other equipment If adjacent or stacked use is necessary the goLITE BLU should be observed to verify normal operation in the configuration 2 cell lithium ion pack 7 AV 850mAh in which it will be used part 4222 018 5787 1 Rechargeable battery type GUIDANCE AND MANUFACTURER S DECLARATION EC 62133 and UL 2054 compliant ELECTROMAGNETIC EMISSIONS The goLITE BLU is intended for use in the electromagnetic environment specified below The user of the Operating conditions goLITE BLU should make sure it is used in such an environment Temperature from 0 C 32 F to 35 C 95 F Emissions Test COMPLIANCE ELECTROMAGNETIC Relative humidity from 15 to 90 no condensation ENVIRONMENT GUIDANCE Storage conditions RF emissions Group 1 The goLITE BLU uses RF Temperature from 20 C 4 F to 50 C 22 F CISPR 11 energy only for its internal function Therefore its RF Relative humidity from 15 to 90 no condensation emissions are very low and are not likely to cause Physical characteristics any interference in nearby y electronic equipment Dimensions 14 x 14 x 2 5cm 6 5 x 5 5 x 98in RF emissions Class B The goLI
13. ise your ability to perform essential tasks such as driving or operating heavy equipment Do not use this appliance where the light might distract other individuals and compromise their ability to perform essential tasks such as driving or operating heavy equipment Do not increase intensity by sitting closer to the light than recommended Increased intensity does not improve response and may result in increased side effects The metal stand for the appliance could present a choking hazard Individuals who use photosensitizing medications who have had cataract surgery or who have pre existing eye conditions should ENGLISH 7 avoid unnecessary exposure to light They should consult their ophthalmologist before using the goLITE BLU The goLITE BLU should never be used adjacent to or stacked with other equipment However if it is necessary the appliance should be observed to verify normal operation Do not position the goLITE or the attached power adaptor in such a way that makes it difficult to disconnect from the power source No modification of the goLITE BLU device is allowed Not suitable for use in the presence of a flammable anaesthetic mixture with air oxygen or nitrous oxide Caution a caution indicates the possibility of damage to the appliance The goLITE BLU energy light contains an internal rechargeable lithium ion battery pack and a coin cell battery Do not incinerate disassemble or expose t
14. o high temperatures above 60 C 140 F Do not operate or charge the GoLITE BLU in temperatures below 0 C 32 F or above 35 C 95 F Batteries can overheat causing fire or bursting Dispose of the appliance with the internal battery properly The user of the goLITE BLU must consider electromagnetic compatability EMC and how portable and mobile RF communication equipment can affect it The goLITE BLU should be put into service according to the EMC information provided at the end of this manual Do not operate this appliance near any heat sources such as radiators heat registers or other heating devices Never use damaged or worn cords or plugs this could result in electric shock burns and or fire Use our provided AC DC adaptor KSAD0950120W1UV 1 only The use of power adaptors other than those specified and provided by Philips may result in increased electromagnetic emissions or decreased immunity of the goLITE Do not place heavy objects on top of the power cord or the appliance When unplugging the appliance grasp the adaptor directly to avoid damaging the cord Never pull on the power cord to remove the adaptor from the outlet 8 ENGLISH ENGLISH 9 If this appliance is damaged in any way or is not working it should not Symbol Key be operated Please call 1 866 832 4361 for assistance The following symbols may appear on the device There are no user serviceable parts inside the goLITE BLU No modification of thi
15. or radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the goLITE BLU is used exceeds the applicable RF compliance level above the goLITE BLU should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as re orienting or relocating the goLITE BLU b Over the frequency range 150 kHz to 80 MHz the field strengths should be less than 3 V m 28 ENGLISH RECOMMENDED SEPARATION DISTANCES BETWEEN PORTABL AND MOBILE RF COMMUNICATIONS EQUIPMENT ANDTHE goLITE BLU The goLITE BLU is intended for use in the electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of the goLITE BLU can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the goLITE BLU as recommended below according to the maximum output power of the communications equipment RATED SEPARATION DISTANCE ACCORDING TO Maximum FREQUENCY OF TRANSMITTER M Power Output OF TRANSMITTER POWER 150 KHz To 80 80 MHz To 800 800 MHz To 2 5 MHz MHz For transmitters rated at a maximum output p
16. ount No 60601 1 2008 Road Markham Ontario L6C 253 This device complies with Part 15 of the FCC Rules Operation is vryyww M Date of Manufacture subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Introduction Intended use The goLITE BLU energy light is intended to make people feel more energetic and to provide mood relief from the winter blues If you suffer from severe mood swings or depression make sure to consult a professional and do not use this device for self treatment This product has not been approved by FDA for treatment of SAD 10 ENGLISH Light and health The human body uses light cues such as those provided by the sun to ime certain functions Light exposure can boost mood and energy Light has direct alerting and energizing effects and can improve our performance Bright light therapy is also successfully used for mood relief especially for seasonal mood swings n countries with long winters many people experience loss of energy and low spirits due to lack of light These symptoms are referred to as the winter blues They typically start in the fall and may last for several weeks Exposure to bright light sources can help alleviate these symptoms and restore the summer mood and summer energy level The blue light of the summer sky is well known We do not
17. ower not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer Note 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people 29 www philips com Mus 4222 002 7504 3
18. r any other liquid nor rinse it under the tap Never use scouring pads abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance Clean the appliance with a dry cloth This appliance has no other user serviceable parts For assistance call 1 866 832 4361 f the appliance will not be used for an extended period of time remove cord from outlet and store in a safe dry location where it will not be crushed banged or subject to damage Do not wrap cord around the appliance when storing Dispose of the device in accordance with local regulations Your local or national recycling organizations may also have disposal information For assistance call 1 866 832 4361 18 ENGLISH Removing the rechargeable battery Only remove the rechargeable battery when you discard the appliance Make sure the battery is completely empty when you remove it Disconnect the appliance from the outlet and remove the appliance plug Turn on the LED panel and leave it on until it goes out automatically Undo the 2 screws with a screwdriver Fig 14 Remove the cover of the built in rechargeable battery Fig 15 Lift the blue rectangular rechargeable battery out of the appliance The battery is connected to the appliance through a red wire and a black wire to a socket inside the appliance Fig 16 Al Grab the wires and pull the socket out of the appliance Fig 17 gt The rechargeable batter
19. s equipment is allowed Symbol Desctiptlen ME Consult accompanying instructions for use SAVE THESE INSTRUCTIONS DC Power IMPORTANT The power plug contains a transformer Do not cut off the power plug to replace it with another plug as this will cause a eee ey hazardous condition SN Serial Number Contraindications ur3332 Model Number The goLITE BLU energy light may not be suitable for use on individuals HE31 who use photosensitizing medications who have had cataract surgery who have pre existing eye conditions or who have bipolar disorder Qu UL Listing Mark for Canada and the United States Thank you for purchasing the goLITE BLU energy light EE Compliant with the Waste Electrical and Electronic Equipment 2 To ful y benefit from the support that Philips offers register your bY Restriction of the Use of Certain Hazardous Substances in Electrical E i and Electronic Equipment WEEE recycling directives goLITE BLU at wwwphilips com welcome ee Learn more about your goLITE BLU at www philips com golite 5 REN n US Manufactured for Philips Consumer Lifestyle Safety and compliance wl A Division of Philips Electronics North America Corporation his appliance meets the requirements of the safety standard for 1600 Summer Street 5th Floor Stamford CT 06905 5125 In medical devices ANSI AAMI ES60601 1 2005 and CAN CSA C22 2 Canada Imported for Philips Electronics LTD 281 Hillm
20. s safe to be used around children and pets However do not let children play with the appliance For most people it is sufficient to use the goLITE BLU once a day Keep in mind that you may have rouble falling asleep if you use the goLITE BLU too ate in the evening f you use the appliance 30 minutes a day throughout he year the LEDs have a lifetime of over 50 years n the unlikely event that one or two LEDs fail prematurely you can continue to use your goLITE BLU normally because its effectiveness is not affected However if several LEDs stop functioning call 1 866 832 4361 for assistance 22 ENGLISH ENGLISH 23 What does When DEMO is on the display the appliance is in Model HF3332 HF3331 DEMO mean demo mode This mode is used to demonstrate the on the display goLITE BLU energy light in stores To turn off this Electrical mode press and hold the on off button for 10 Rated voltage appliance VAC 100 240 seconds when the goLITE BLU is turned off The goLITE BLU turns on and the word DEMO ee V DO a disappears from the display Rated frequency Hz 50 60 How do use The reset button is located in the stand storage Rated input power adaptor A 1 2 the reset cavity on the back of the appliance If the goLITE 5 ti ii A 14 button BLU locks up or does not work correctly reset the RA appliance by inserting the end of a paperclip into the Power consumption adaptor A 0 4 reset button hol
21. session Note If you pause a session while the appliance operates on battery power and do not continue the session within 5 minutes the appliance turns off automatically Setting the alarm The alarm has three modes chime only light only or both chime and light Press the on off button briefly to turn on the appliance Fig 6 D The touchscreen display goes on Press the alarm button Fig 12 D The alarm indications start to flash Fig 13 Press the plus or minus button to switch between the three alarm modes chime only light only or both chime and light Fig 9 Press the alarm button twice or wait 10 seconds to store the selected mode To set the alarm time press the alarm button twice D The alarm time starts to flash EJ Press either the plus or the minus button to set the desired time If you keep the button pressed the time moves forward or backward quickly Press the alarm button or wait 10 seconds to store the set alarm time Note The set alarm mode and time remain stored in the memory as long as there is energy in the battery ENGLISH 17 Turning off the alarm sound Press any of the touchscreen buttons or the on off button to turn off the alarm sound when the alarm goes off Disabling the alarm To disable the alarm press and hold the alarm button until the alarm chime and the alarm light indications as well as the alarm time disappear from the display Never immerse the appliance in water o
22. time from 1 to 60 minutes D The set session time is stored in the memory D The timer on indication and the timer countdown time stop flashing Note When you turn on the appliance the timer counts down the set time When the countdown is finished the LED panel turns off automatically Demo mode The demo mode is used to demonstrate the goLITE BLU energy light in stores When the appliance is turned on in demo mode customers of the store can adjust the light intensity turn the appliance on and off set the alarm set the light time If the appliance is not operated for 3 minutes it reverts to its demo mode default settings To activate the demo mode Make sure the appliance is turned off Note If you want to turn off the appliance press and hold the on off button for 2 seconds Put the adaptor in the wall outlet and insert the appliance plug into socket on the appliance Press and hold the on off button for 10 seconds Fig 6 D The appliance turns on and the word DEMO appears on the display gt The LED panel goes on at a light intensity of 25 ENGLISH 15 D The display shows a timer countdown time of 15 minutes but the timer does not count down It only starts to count down when the timer time is adjusted D The display shows an alarm time of 12 00 a m and shows the normal clock time but the alarm mode is off Note The appliance remains turned on in demo mode until it is turned off
23. y has now been removed Dispose the battery in accordance with local regulations Assistance For assistance call toll free 1 866 832 4361 or visit our website www philips com golite 45 Day Money Back Guarantee If you are not fully satisfied with your Philips goLITE BLU energy light send the product back along with the original dated sales receipt and we will refund you the full purchase price he goLITE BLU must be shipped prepaid by insured mail insurance prepaid and have the original sales receipt indicating purchase price and the date of purchase enclosed We cannot be responsible for lost mail he goLITE BLU must be postmarked no later than 45 days after the date of purchase Philips reserves the right to verify the purchase price of the goLITE BLU and limit refunds not to exceed suggested retail price ENGLISH 19 To obtain Money Back Guarantee Return Authorization Form call 1 866 832 4361 Please allow 4 6 weeks for delivery of the check Full Two Year Warranty Philips Electronics North America Corporation USA and Philips Electronics Ltd CANADA warrant each new Philips product model HF3332 HF3331 against defects in materials or workmanship for a period of two years from the date of purchase and agree to repair or replace any defective product without charge IMPORTANT This warranty does not cover damage resulting from accident misuse or abuse lack of reasonable care or the affixing of
Download Pdf Manuals
Related Search