Planar Systems PL1700
Contents
1. please perform the following steps 1 Make sure the power indicator on the LCD Monitor is ON all connections are secured and the system is running on the correct timing Refer to Chapter 3 for information on timing 2 Turn off the LCD Monitor and then turn it back on again If there is still no picture press the Adjustment Control button several times 3 Ifstep 2 doesn t work connect your PC system to another external CRT If your PC system Functions properly with a CRT Monitor but it does not function with the LCD Monitor the output timing of the VGA card may be out of the LCD s synchronous range Please change to an alternative mode listed in the Standard Timing Table or replace the VGA card and then repeat steps 1 and 2 If you have chosen an output timing that is outside of the LCD Monitor s synchronous range the OSD will display a Out of Range message Choose a mode that is supported by your LCD Monitor Also if the signal cable is not connected to LCD monitor at all or properly the monitor screen will display a message No Input Signal 12 Planar Systems Inc 1195 NW Compton Drive Beaverton OR 97006 1992 www planar com O 2006 Planar Systems Inc Planar is a registered trademark of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice HDPNRP5710I2. the monitor already has escaped from OSD Lock Out function Chapter 3 Technical Information Specifications LCD Panel PL1700 PL1700M Size 17 43 2 cm Display Type Active matrix color TFT LCD Resolution 1280 x 1024 Display Dot 1280 x RGB x 1024 Display Color 16 2M RGB 6bit FRC Video Input Signal Analog RGB 0 7Vp p Input Impedance 75 Ohm 2 Polarity Positive Negative Amplitude 0 0 7 0 05 Vp Control Power switch On Off switch with LED indicator Audio Input 500mVrms Output 1W 1W OSD Brightness Digital Contrast Digital Horizontal Position Digital Vertical Position Digital Phase Digital Clock Digital Display Mode Setup Use EEPROM to save settings in memory OSD Format 26 characters x 15 rows Power Management Nc Power Consumption AC Input LED Color 40W maximum for PL1700 240 VAC Green 48W maximum for PL1700M 240 VAC TOA stk off 240 VAC Yellow Standby Suspend Off Meeting VESA DPMS requirements measured from AC Input end of AC power cord Sync Input Signal Polarity Plug amp Play External Connection Power Input AC input Video Cable Audio Cable PL1700M only Environment Operating Condition Storage Condition Power Supply AC Input Input Voltage Input Current Size and Weight Dimensions Net Weight Gross Weight Standard Timing Table Separate TTL compatible horizontal and vertical synchronization Positive and negative Supports VESA DDC2B func
3. 2 Display COHIPFOIS oirisider rito aE a a User Controls Adjusting the Monitor s Display Function Description Chapter 3 Technical Information sssssssssssssscssooooossssssesecccccccoocccssssssssccceseceeccooosossssssssseeeee Y Specifications Standard Timing Table Troubleshooting Preface This manual is designed to assist users in setting up and using the LCD Monitor Information in this document has been carefully checked for accuracy however no guarantee is given to the correctness of the contents The information in this document is subject to change without notice This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer FCC Statement Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television recept
4. After Auto Adjustment the picture may show a picture in the incorrect size if it is receiving a pattern which has no screen border LT Ext Saves the values of this setting and exits the OSD menu function Icon Function Description 9300 CIE coordinated Color Temperature of 9300 K Men A UO QD no 7500 CIE coordinated Color Temperature of 7500 K oe CI CO OsOM ate a 6500 CIE coordinated Color Temperature of 6500 K a e te U Three colors Red Green Blue can be adjusted Sets the settings to a by user defined CIE Ser from the OSD menu Temperature Notice OSD Lock Out Function When monitor is in normal display you can enable the OSD Lock Out function How to enter OSD Lock Out function gt Step 1 The monitor is displaying after power on Step 2 To press the buttons VOL and VOL and Function gt at the same time for 3 seconds or more Step 3 Monitor will show an OSD Lock Out message for 5 10 seconds and the message will disappear automatically While the monitor is in the state of OSD Lock Out if press OSD button OSD Lock Out message will appear for 5 10 seconds on screen How to exit OSD Lock Out function gt Step 1 When the monitor is in the state of OSD Lock Out Step 2 To press the buttons VOL and VOL and Function gt at the same time for 3 seconds or more Step 3 Display will show main OSD menu Now
5. Mm PLANAR PL1700 PLL700M LCD Monitor USER S GUIDE www planar com Planar Systems Inc 1195 NW Compton Drive Beaverton OR 97006 1992 www planar com Customer Service Planar provides the following technical support services Internet Support For support available 24 7 visit Planar s Online Technical Support at www planar com support Our Online Technical Support is where you ll find solutions to many common problems download documentation view answers to frequently asked questions FAQs and get troubleshooting advice or email Planar your support question Talk to a Customer Service Representative To contact Planar s Customer First TM Technical Support Service call 1 866 PLANAR 1 866 752 6271 This service is available 5am 5pm Pacific Time 8am 8pm Eastern Time Monday through Friday Contact Us 24x7 Online Technical Support http www planar com support Email PlanarSupport planar com Tel 1 866 PLANAR1 866 752 6271 Hours M F 5am 5pm Pacific Time 8am 8pm Eastern Table of Contents A A M 1 jugi P E d 3 Chapter TIAS AAA Unpacking Connecting the LCD Monitor and Base Viewing Angle Adjustment Connecting the Display Connecting the AC Power Connecting the Audio Cable PL1700M Setting Up the LCD Monitor Power Management System Optional Mounting Alternatives Detaching LCD Monitor from Its Stand Interface for Arm Applications Chapter
6. Monitor s Display The monitor has four function control buttons to select among functions shown on OSD menu designed for easy user viewing environments OSD Function Menu To access OSD Main menu simply press one of the Function Select control buttons and the menu diagram will pop up on the screen as shown on Fig 2 2 Continue pressing the Function Select buttons to scroll through the entire menu items then press Adjustment Control buttons to 1 1 1024x768 60HZ adjust content of selected item VER 0 21MTC 80 Figure 2 2 Attention Firmware revision may have been updated into a latest version while the version number shown on all OSD menus in this manual will stay as Ver 1 00 Function Description on Brightness 101 scales of brightness are available to choose from 010 100 Contrast I0 scales of contrast are available o choose from 010 100 H Posiion This function let s you adjust the display s horizontal position V Posit This function let s you adjust the display s vertical position This function let s you select the images sharpness Five selections are Sharpness available A smoother setting is more suitable for pictures while a sharper setting 1s more suitable for text OSD This function let s you set the transparency of the OSD menu The asparenev transparency is adjustable from 0 to 3 4 scales are available A total of 101 scales 0 to 100 are available to adjust the focus and cl
7. arity of the display This function carries a frequency tracking feature that offers users better stability and clarity 101 scales from 50 to 50 are available on the mode Clock that is currently running The adjustable range can be variable in different modes This function records the deviated number of clock period between input timing and supported timing The clock value may not be 0 after Auto Adjustment when the input timing is different from supported timing Color Push the Erst button to select a different color temperature Please see the Temperature diagram below for function and description Cod i OSD V Position This function moves the OSD menu window vertically Because the H and V Frequencies of both 640 x 400 70Hz and 720 x 400 Graph Text 70Hz are the same this function let s you manually select either 640 x 400 graphics mode or 720 x 400 text mode l Pur Real The recall function will return all adjusted parameters to factory preset values f A Eight OSD language options are available Language English German French Spanish Italian Japan Russian and Chinese simple Press the left or right adjustment control button to select other language Press button Eh to activate the selected function Auto Adjustment The Auto Adjustment function lets you adjust the display size clock and phase Auto to obtain the best viewing settings This process will take 3 5 seconds to complete Attention
8. column and pull down the hinge to release Figure 1 3 Interface for Arm Applications Before installing to mounting device please refer to Fig 1 3 The rear of this LCD display has four integrated 4 mm 0 7 pitches threaded nuts as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1 4 These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard paragraphs A 2 1 and 2 1 3 version 1 dated 13 November 1997 ta Note Please using M 4mm x 10mm L screw for this threaded holes x4 application 75mm x 7bmm Screw Mounting Options 75mm Figure 1 4 Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor function controls and indicators Figure 2 1 Stereo Speakers Speaker Volume Increase Volume Turn knob clockwise Control PL1700M only Decrease Volume Turn knob counter clockwise DC Power Switch Press the power switch to switch the monitor ON OFF DEP POS LED lights Green color Power is ON idi P i LED lights Yellow Monitor is in Power Saving Mode Mae atOr LED is off Power is OFF Buttons menu selection Adjustment Control Press the left button to decrease the OSD setting and press the right UF M CHI MN The monitor speakers will be disabled when using an external Jack PL1700M only headphone or external speakers Adjusting the
9. ion which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reposition or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced monitor technician for help Warning Use only shielded signal cables to connect I O devices to this equipment You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Ji Regulations Cet appareil num rique de la classe B repecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Important Safety Instructions Please read the following instructions carefully This manual should be retained for future use ll Oo To clean LCD Monitor screen Power off LCD Monitor and unplug the AC Cord Spray a non solvent cleaning solution onto a rag Gently clean the screen with dampened rag Do not place the LCD Monitor near a window Exposing the monitor to rain water moisture or sunlight can severely damage it Do not apply pressure to the LCD screen Excess p
10. nitor stand Connecting the Display 1 Power off your computer 2 Connect one end of the signal cable to the LCD Monitor s VGA port See Fig 1 5 3 Connect the other end of the signal cable to the VGA port on your PC 4 Make sure connections are secure Connecting the AC Power Connect the power cord to the LCD Monitor See Fig 1 6 2 Connect the power cord to an AC power source ONE the Audio Cable PL1700M Connect the audio cable to the LINE OUT jack on your PC s audio card or to the front panel s AUDIO OUT jack of your CD ROM drive See Fig 1 7 2 Connect the other end of the audio cable to the LCD Monitor s LINE IN jack Setting Up the LCD Monitor 1 Make sure the AC power cord is connected to the LCD Monitor e EA cas Y AA gt VGA Port Power Cord AC Power Jack Audio Jack 2 Turn on the LCD Monitor s power switch located on the bezel of the monitor Figure 1 5 Figure 1 6 Figure 1 7 Power Management System This LCD Monitor complies with the VESA DPMS version 1 0 Power Management guidelines The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync signal When the LCD Monitor is in power saving mode the monitor screen will be blank and the power LED indicator will light yellow Optional Mounting Alternatives Detaching LCD Monitor from Its Stand Unscrew screws O the swivel base support
11. ressure may cause permanent damage to the display Do not remove the cover or attempt to service this unit by yourself Servicing of any nature should be performed by an authorized technician Store LCD Monitor in a room with a room temperature of 20 60 C or 4 140 F Storing the LCD Monitor outside this range could result in permanent damage If any of the following occurs immediately unplug your monitor and call an authorized technician Monitor to PC signal cable is frayed or damaged Liquid spilled into LCD Monitor or the monitor has been exposed to rain LCD Monitor or the case is damaged Only use the supplied main lead to connect the monitor For a nominal current up to 6A and a device weight above 3 kg a line not lighter than HOSVV F 3G 0 75 mm must be used Hg s Recycle Instruction LCD Lamp s inside this product contain mercury This product may contain other electronic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal Laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG Chapter 1 Installation Unpacking Before unpacking the LCD Monitor prepare a suitable workspace for your Monitor and computer You need a stable and clean surface near a wall power outlet Make sure that LCD Monitor has enough space around it for sufficien
12. t airflow Though the LCD Monitor uses very little power some ventilation is needed to ensure that the Monitor does not become too hot After you unpack the LCD Monitor make sure that the following items were included in the box LCD Monitor User s Manual Monitor to PC VGA Cable Stereo Jack Audio Cable Power Cord Base Register Your Planar Products Today Thank you for choosing Planar To assure you receive all the benefits of your Planar product and services register your Planar product today Visit our website to register your product at http www planar com support product registration html Cables Replacement Lamps and Accessories To find cables replacement lamps and accessories for your Planar projector LCD monitor touchscreen or other Planar products visit our online store at www PlanarOnline com or find other stores who carry Planar products at http www planar com howtobuy Connecting the LCD Monitor and Base When you open the box to take the base and put on the desk first Then connect the LCD Monitor and base please See fig 1 1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle The viewing angle can be adjusted from 5 to 30 See fig 1 2 Warning Figure 1 1 Figure 1 2 Do not force the LCD Monitor over its maximum viewing angle settings as stated above Attempting this will result in damaging the Monitor and Mo
13. tions AC socket 15 pin D sub connector Stereo Jack Temperature 5 C to 40 C 41 F to 104 F Relative Humidity 20 to 80 Temperature 20 C to 60 C 4 F to140 F Relative Humidity 5 to 85 Single phase 100 240VAC 50 60 Hz 1 2 A maximum 374 W x 387 H x 190 D mm 5 0 3 kg 7 0 3 kg If the selected timing is NOT included in table below this LCD monitor will use the most suitable available timing TIMING ae T POLARITY VGA 350 NEC PC9801 VGA GRAPH VESA PAL VGA 480 APPLE MAC 480 640x480 VESA 480 72Hz 640x480 VESA 480 75Hz SYNC WIDTH DOT LINE 640x400 gt NEC PC9821 70 15 dumm rus 720x400 VGA 400 TEXT 832x624 APPLE MAC 800 800x600 SVGA 800x600 VESA 600 60Hz 800x600 VESA 600 72Hz 800x600 He VESA 600 75 Hz FH KHZ SYNC ACTIVE SYNC FV HZ POLARITY DOT WIDTH LINE DOT LINE 136 6 176 4 1024x768 XGA 1024x768 COMPAQ XGA 1024x768 56 476 75 1024x768 dE VESA 768 70Hz 70 069 1024x768 60 24 APPLE MAC 768 75 02 60Hz 1152x864 70Hz 1152x864 1280x960 60 00 1800 1280 60 00 1000 960 1280x960 7000 1800 1280 70Hz 7000 1000 960 1280x960 7500 1800 1280 75Hz 75 00 1000 960 1280x1024VESA 64 1688 1280 1024 60Hz 60 1060 104 3 1280
14. x1024VESA 80 1688 1280 144 l6 1024 75Hz Note Mode 640x350 640x400 and 720x400 will locate on middle position but cannot be expanded to full screen on vertical direction VESA 768 75Hz II Hl g HM DERI 11 Troubleshooting This LCD Monitor has pre adjusted using factory standard VGA timings Due to the output timing differences among various VGA cards in the market users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected Attention This LCD Monitor Supports Multiple VGA Modes Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor PROBLEM Picture is unclear and unstable The picture is unclear and unstable please perform the following steps 1 Enter PC to Shut Down Windows status while you re in MS Windows environment except Windows XP In Windows XP open the specific application where the problems appear 2 Check the screen to see if there s any black vertical stripes appear If there are take advantage of the Clock function in OSD menu and adjust by increment or decrement numbers until those bars disappear 3 Move to Phase function in OSD menu again and adjust the monitor screen to its most clear display 4 Click No on Shut Down Windows and back to the normal PC operating environment PROBLEM There is no picture on LCD Monitor If there s no picture on the LCD Monitor
Download Pdf Manuals
Related Search