Phihong POE125U-8C
Contents
1. Enable Disable All Ports 7 Detect Legacy Signature Legacy Detect is Enabled Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Part 7 Port 8 Port 9 Port10 Port 11 Part 12 JE JE AE JE 0 9 9 a Port b Enable Pot 13 Portl4 Portis Port 16 Port 17 Port18 Port19 Por20 Port21 Por22 Por 23 Port 24 eo 980 o 9o o o o vo 9 e Port 3 i Enable LED Key Port status Detecting Disable Error Port Connected NOTE To send changes made in this section to the PoE system click on Send Port Control Changes to the port configuration in this section can be enacted when the user clicks the Send Port Control button It will send the port information to the uP for 24 Ports Please allow the GUI 10 seconds to refresh when this action is taken Port Description Click Edit to edit change the description of the port Click Ok to set description on the GUI screen If you click Cancel the previous description will be set for that particular port Click Send Port Control to send the descriptions to the system To make this permanent the user must click Save Parameters to Flash Enable This check box can administratively enable or disable the selected port If Enable Disable All Port checkbox is selected all ports will be enabled Initially the checkbox is not checked but by default all ports are enabled Click Send Port Control to send the command to the system To make this permanent the use2. Firmware Version i D LAN amp WAP cm Save MOIS Hardware Version F4 Connection Type GBA Reset to Flash SNMP LAN amp WAN eme Port Number LER ERE Firmware Restore Factory System ID ER Download Defaults Description Edit Port Description Parametric Information Port Commands Enable Disable All Ports Detect Legacy Signature Send Port Control Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 9 Port10 Portil Port12 9o 9o 9 9 6666 6 Description Edit Enable Port13 Port14 Porti15 Port16 Port17_ Porti8 Port19 Port20 Port21 Port22 Port23 Port24 9 9o o o 9o 9o o o 6 Port Description Enable LED Key Port status Detecting Disable Error Port Connected Figure 21 GUI Main Window NOTE To send changes made in this section to the PoE system click on Send Port Control Step 2 Select Com Port number then press Search POE and highlight the midspan Connection Information Connection Information Connection Type USB soft RS232 m Connection Type USB soft RS232 OP Search PoE E Search PoE Figure 22 GUI Connection Information Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com gt 10 PHIHONG 4 2 GUI System Control and Information The System Control and Information panel on the GUI supports the main system level parameters for the uP It
3. PHIHONG Phihong Midspan POE GUI User Manual SNMP v3 v2 v1 Rev 1 0 PES12780 Compliant Models POE125U 8N POE370U 480 8N POE370U 480 16N POE360U 480 24N POE576U 8ATN POE576U 16ATN POE576U 24AFATN PHIHONG Disclaimer Phihong accepts no accountability or liability arising from the use of the Midspans as described in this document The handling of equipment will be users responsibility Applications described in this document are for descriptive purposes only Phihong does not provide warranty on modified products Notice This document contains information about the software and hardware used on the Midspan The information is held to be accurate and reliable from time of print Please be advised that product development and revisions are still in course of action Phihong cannot be held responsible for involuntary error exclusions inaccuracies or following changes of printed material Phihong reserves the right to make changes to products and to their specifications as described in this document at any time without prior notice The contents of this document may not be photocopied or reproduced in any form without written permission of Phihong NOTE Midspans are for indoor use only August 2009 Phihong USA Corp All Rights Reserved This document is subject to change without notice Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com
4. The main window of the controller is a simple GUI that allows the user to enable and disable midspan ports It 1s also a limited display of parametric information A more complete list of parametric information is available using Phihong s GUI software available on the website www midspans com Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 30 PHIHONG 3 1 System Administration Figure 33 Controller System Administration Configuration Microsoft Internet Explorer b File Edt vew Favorkes Tools Help ar Qm O HAG Pen O 3 URS Address http 192 168 21 121jsys Google eB Search SH deo Bt ty Bookmarker A Check Ej Autor Mr amp nr a ED ien PHIHONG ie Device Configuration re gt Administration l Administrator admin Password IP Address 192160 31 101 Subnet Mask 2552552550 Gateway DNS Server 168951921 DHCP Client Enable v Firmware Backup Backup Firmware Update Restore Default Settings Default Reboot System Reboot v E pone ic 8 nem F NOTE If you change the Administrator name and password users should ensure that it is written down in safe place for reference Click to make any changes permanent Ok Settings have been saved successfully Click to reboot the system with the new changes This may take a few minutes dependi
5. Ei sNMPsa User AuthPassword PrvPassword Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 36 PHIHONG If you wish to run your SNMP device in Static mode you can also configure your IP Address and Subnet Mask through the Ethernet Manager tool etm exe Click Config IP Address NOTE From the System Setup menu in the Controller your DHCP Client setting must be Disable Figure 39 Ethernet Manager Set IP Address Ethernet Manager View Config IP Address Subnet Mask HAC Address Device ID 199 168 21 121 255 255 255 0 B8 61 3D 82 80 BA 1 Set IP Address IP Address Subnet Mask 255 255 255 0 Cancel Devices detected 1 Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 2375 PHIHONG 4 DHCP Client Dynamic or Static Mode Check your Local Area Connection Status 4 Local Area Connection Status Local Area Connection Status General 5 upport Connection Connection status Status Connected Address Type Assigned by DHCP D uration 04 13 13 IP Address 192 168 31 119 Speed 100 0 Mbps Subnet Mask 255 255 255 0 Default Gateway 192 168 31 1 Windows did not detect problems with this Repair Sent i Received connection If you cannot connect click
6. La Repair Packets 132 731 114 783 Activity Figure 40 Local Area Connection Status Click Double click Internet Protocol TCP IP to view the properties If the DHCP Client is Disabled it is in Static mode The user has the option to manually set the IP Address Subnet mask and Gateway Address for your PC If the DHCP Client is Enabled it is in Dynamic mode obtain an IP address automatically The Network will automatically set the IP Address Subnet Mask and Gateway Address for your PC Figure 41 Local Area Connection Properties Internet Protocol Properties Local Area Connection Properties kd Eg Internet Protocol TCP IP Properties General Auherticain Advanced Connect using You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask pour network administrator for ES Intel R PRO TO0D VE Network Conne the appropnate IP settings This connection uses the followang items O Obtain an IP address automatically Jill nas Use the following IP address _ Network Monitor D IP address 12 18 39 119 Subnet mask 255 255 255 0 Default gateway 192 168 31 1 Uninstal Description Uban ONS server address automatically Transmission Control Protocol Intemet Protocol The default Use the following DNS server addresses ee ike Preferred DNS server 192 168 31 Alternate DNS server v Show icon in notification a
7. To make the factory defaults permanent the user must click Save Parameters to Flash The System ID field specifies the hardware revision of the PoE device The firmware version is represented in a major minor format oystem ID Name click Edit to edit change the description of the system If you click Cancel the previous description will be set for the system To make this permanent the user must click Save Parameters to Flash Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 0 PHIHONG During the Download In Progress the GUI function buttons will be temporarily disabled Figure 24 System Update Reset Update system Port Param system save Parameters Heset to Flash DOWNLOAD Hestore Factory IN Defaults PROGRESS Example of GUI firmware file PoES 6Firmmarev09 O51509 599 73KB 599 File 5115 2009 901 AM Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com D PHIHONG 4 3 GUI Port Description The Port Description panel shows 24 ports On the PoE Midspans that have 8 or 16 ports the port numbers higher than the system port count will be shaded grey and disabled Each section specifies the individual port descriptions for the system Figure 25 Port Description Port Description Parametric Information Port Commands
8. ports 6 14 22 ports 7 15 23 ports 8 16 24 All 24 Ports are connected LED remains green d 24 Ports without ports connected LED turns orange green orange green turns off LED blinks orange individually ports 1 9 17 ports 2 10 18 ports 3 11 19 ports 4 12 20 ports 5 13 21 ports 6 14 22 ports 7 15 23 ports 8 16 24 Blinks orange across all 24 Ports When System Reset is clicked on the GUI applications file a b AC LED remains green NIC LED remains off until the unit is connected 24 Ports with ports connected same sequence as Cold Start 24 Ports without ports connected same sequence as Cold Start Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com d PHIHONG Table 1 LED Indicator Indicates Indicates NIC NIC is is connected disconnected form Network to Nework 2 7 Rack Mounting Installation Figure 12 Rack Mounted Midspan Front Figure 13 Rack Mounting Bracket and screws side rear Position the Midspan on the rack Arrange the mounting bracket to the corresponding screw holes on the Midspan Keep the screw area visible to insert screws and then tighten the screws Screws and brackets will be included in the package Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 5
9. 24952 2 2 0 0 poeSystemProductPartNumber INTEGER Read only Displays the product part number E O24852 2200 poeSystemFirmwareVersion DisplayString Read only System firmware version for the PoE Loo 2M poeSystemDescription DisplayString Read Write System SIZE NO Description max length of 10 characters Wien E poeSystemConsumptionPower INTEGER Read only Measured power usage expressed in Watts 201222522270 poeSystemcontrolACPower INTEGER Read Write Sets the value of available power in Watts to be suplied by primary AC power source Wi 220522 2772 08 poeSystemControlDCPower INTEGER Head Write Sets the value of available power in watts to be supplied by secondary DC power supply Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com E PHIHONG SS en poePortlndex INTEGER Read only A unique value for 1 3 6 1 24852 2 3 1 3 1 24 poePortControlMaxPower INTEGER Head Write each port This command specifies the max power in watts to the port Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com AD 1 3 6 1 4 1 24852 2 3 1 5 0 1 3 6 1 4 1 24851 1 2 1 6 1 24 1 3 6 1 4 1 24852 2 3 1 7 1 24 1 3 6 1 4 1 24852 2 3 1 8 1 24 1 3 6 1 4 1 24852 2 3 1 9 1 24 1 3 6 1 4 1 24852 2 3 1 10 1 24 PHIHONG KKK poePortCurr
10. Figure 2 Data amp Power top row Data bottom row Figure 3 Connectors and Indicators Hear Side of the Midspan Figure 4 The Rear Side of the Midspan ve hh eh d NIME aoc oso EE e s uoc Figure 5 DC Power Connector 6 47VDC to 57VDC DC IN Molex 6 pin p n 39 30 0060 or equivalent DC IN Mate Molex 39 01 2065 pin p n 39 00 0077 Figure 6 AC Input Connector AC IN IEC320 inlet 3 pin Optional Components please see appendicices A and B Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 8 PHIHONG 2 4 Powering Your Midspan Power Cord Requirements Power cords must meet the requirements for the country it is intended to be used U S A and Canada Europe e he cord must have a minimum of 10A rated current competence e The cord must be CSA or UL approved e The minimum requirement for the flexible cord is o 18 AWG 104 o Three Conductor Line Neutral Ground o Type SV stranded Vacuum Rubber Jacketed or SJ stranded Junior Rubber Jacketed or SVT Stranded Vacuum Rubber Jacketed Thermoplastic or SJT Stranded Junior Thermoplastic e The plus must be earth grounded with a NEMA 5 15 15A 125V or NEMA 6 15P 15A 250V configuration Switzerland e The supply plug must comply with SEV ASE 101 1 Denmark e The supply plug must comply with section 108 2 D1 standard DK2 1a or DK2
11. also displays information about the PoE ID firmware revision and system status Figure 23 System Setup Control Information and Port Commands Reset Update oystemjPon Param system Information Firmware Version System Save Parameters Hardware Version Reset to Flash Port Number ea ac Bear en System ID ownloa REAL Description The system level parameters that can be configured are Edt e System Reset This is a function that allows the GUI to reset the software on the uP If System Reset is set and the GUI does not respond user must click Reset GUI e Firmware Download This feature is used to download new application firmware codes onto the uP Please refer to the Phihong website www midspans com for the latest firmware for your midspan POE Firmware Note Please allow the GUI a few seconds to respond to the commands selected DO NOT click or check any commands simultaneously If a command is selected more than once within two seconds the GUI may not respond properly The Save Parameters to Flash button will save system and port parameters to flash memory so that they can be used to the firmware across reboots of the uP The Restore Factory Defaults button will reset the defaults in the firmware and clear any stored data in the flash memory the device will reset automatically After the device has successfully reset the System Status will read 0 Click Reset GUI if necessary
12. 10 445 1678 www phihong com or www midspans com 12 PHIHONG 2 7 Technical Specifications Figure 14 Technical Specifications Output Voltage J80 50VDC Bann gt 560 56VDC H option NIC interface Model Family X number of ports ood gt 5 YrrrYr AT Allpors have 53 6W output AFAT 8 Ports 35 6 Wr16 Ports 15 48 E option DC input Output Voltage 560 56VDC N option NIC interface POES70U _ x YYYY R 4 Bite Model Family X number of ports p 2d gt 5 Mechanical Specifications Dimensions 17 25 inch 438 mm length 8 98 inch 228 mm width 1 75 inch 44 5 mm height Environmental Specifications Temperature e Operating 0 C to 40 C e Non Operating 25 C to 65 C Contact Phihong Sales for this option Relative Humidity e Operating 5 to 90 e Non Operating 5 to 90 Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com n PHIHONG Electrical Specifications Table 2 Electrical Specifications Parameters Specifications AC Input Voltage Rating 100V AC to 240V AC AC Input Voltage Range 90V AC to 264V AC AC Input Current 5 5A RMS at Max Load AC Input Frequency 47Hz to 63Hz 60A for 230V AC at Max Load AC Output Voltage Max Load Current Output Power per Pot 15 4W not to exceed total output power POE370U 125W max 250W max 370W max Phihong USA Cor
13. 2 Device Manager to view Port Properties When you are ready to begin please connect the proper end of the USB to Serial cable to your Midspan and the other to an available USB port on your PC If you installed the USB driver described above your PC will locate the new hardware To view which Serial COM Port your Midspan is installed please follow the instructions j Phihong POE SNMPv3 GUI Setup Please click DeviceManager E Device Manager PER b File Action View Help E amp E m Batteries _ Bluetooth VCOMM Port sg Computer s Disk drives gt Display adapters 25 DVDJ CD ROM drives Ha Human Interface Devices IDE ATASATAPI controllers amp IEEE 1384 Bus host controllers cw Keyboards jj Mice and other pointing devices L Modems E Monitors BS Network adapters E PCMCIA adapters PCMCIA and Flash memory devices Ports COM amp LPT E Prolific USB to Serial Comm Pork OON RIM virtual Serial Port v2 tic oME Rn RIM virtual Serial Port va KOM Processors the following window will open FG HH HEHE HERE Figure 17 Device Manager Locate and Expand Ports COM amp LPT Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 16 PHIHONG Double Click the Prolific USB to Serial Comm Port COM n this example the USB to Serial Comm port is installed on Com1 The Com port will va
14. 5 255 8 88 81 3D 82 88 Bf lp sna Read Community Public Set Community private SNMPy3 admin Devices detected 1 Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 39 PHIHONG Step 2 Select Search POE If Phihong POE device is found click to select device Figure 44 GUI Connection Information Connection Information Connection Type SNMP LAN amp WAR v search PoE 1192 168 31 121 POEb 7bEU Z4HP NOTE The IP address will be saved internally for the next use Figure 45 GUI Main Window EL Phihong MIDSPAN POE GUI System Information Operation Reset Update System Port Param System Information Connection Information Firmware Version io PILA JAP to Flash PLC t Port Number 24 Search PoE Firmware Restore Factory 92 168 31 119 POE576U 24HP Description Edi Port Description Parametric Information Port Commands Enable Disable All Ports Detect Legacy Signature Legacy Detect is Enabled Send Port Control Part 1 Port 2 Port 3 Port 4 Port 5 Port amp Part 7 Part 8 Port9 Port 10 Port 11 Part 12 099009 e e v o o e Enable v v v v acm Port 13 Port 14 zum 15 For is Port 17 Port S digi ae Port 20 Port E co 2 Port 23 Bart 24 Po Enable v e RR LED Key Port status NOTE To send changes made in this section to the PoE Detecting
15. 5a United Kingdom e The Midspan is covered by General Approval section 16 16 060 NS G 12345 J100003 for indirect connection to a public telecommunication system France and Peru e T equipments cannot power this device In the case of an IT powered device the unite needs to be powered by 230V through an isolation transformer with a ratio of 1 1 and the secondary connection Neutral is properly grounded e The Midspan must have access to a nearby power outlet By disconnecting the power cord from the outlet you will eliminate power from the device e The flexible cord that connects to the Midspan must have a configuration to connect with an EN60320 IEC320 inlet connector e According to the EN60950 IEC 950 specifications this device functions under SELV Safety Extra Low Voltage conditions The conditions are true if the equipment and the connected device functions under SELV conditions Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com as PHIHONG 2 3 Connecting Ethernet Cables Figure 7 POE370U 480 24N connected through data amp power line 2 4 al L4 e AT u Figure 8 NIC Cable Connected 2 4 Connecting USB and Power Cables USB cable The USB cable is connected to the USB connector located in the front side of the Midspan and a USB port on your PC laptop Figur
16. 678 www phihong com or www midspans com 34 PHIHONG 3 2 SNMP Settings The new SNMP v3 has added security features that were not found on previous versions of the management protocol These include additional password protection Figure 36 Controller SNMP Settings 1 wu Lm TES I GY RES Vua y se O O AO P 4e AS J amp 8 93 I Address http j192 168 31 12M sys E Google v serch Sa Be V Bookmarks SP Check E Autorii 7 pr 8 n je n fl PHIHONG s Device Configuration SNMP Versions v1 OV EI v3 Iv Community String get public nu cet private iser admin NN Authentication Made HMAC MDS v Authentication Password Privacy Mode CBC DES v Privacy Password ii EM Trap hasts F able 6 SNMP Setting ettings SNMP Settings Default Setting Get Community String Option to set to public or private Logon name that may be defined by the user If changed the information should be written in a safe palce for future reference User defined password may be left blank or 1 18 characters in length If changed the information should be written in a safe place for future reference This option may be used in place of the community string Authentication Password Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 35 PH
17. C Interface Midspan Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 46 PHIHONG Q What happens if I forget my username and passwords for the NIC Interface Appendix D Frequently Asked Questions A Please contact Phihong Sales for further information on this topic Q What is the function of the current share pin on the CD Power connector Are there any protocols or procedures associated with it A The DC solution contains 3x 500W 50V rectifier modules 1000W N 1 with custom cables available for connection between the rectifier rack and up to 4 midspans The current share pin is an option which could be used to have the power supply inside the midspan current share with the rectifiers There are no protocols or procedures associated with it other than it s designed only to work with our rectifier system and even then its not perfect sharing due to the inrush limiting components inside the midspan located on the DC input Q What type of Display Properties settings are required to run the Phihong SMNP v3 GUI A 16 Bit 1024 X 768 pixels 1280 X 1024 pixels 32 Bit 1024 X 768 pixels 1280 X 1024 pixels If the settings are set to be at least the values shown below the edges of the GUI window will be cropped 16 Bit 640 X 480 pixels 800 X 600 pixels 32 Bit 640 X 480 pixels 800 X 600 pixels Phihong USA Corporation e 47800 Fr
18. Disable Error Port Connected system click on Send Port Control j All features except for the Firmware Download are supported Please refer to section 4 Midspan GUI of this document for the full description of the Phihong GUI features To update firmware using SNMP please refer to section 7 Controller Setup Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 40 PHIHONG Appendix C SNMP MIB Phihong USA Corp registered Enterprise ID 1 3 6 1 4 1 24852 SNMP Version SNMPv3 TCP UDP Port 161 SNMP Simple Network Management Protocol 1 Table 7 SNMP MIB To oO 24352 22 FO poeSystemActionHubReset INTEGER ready 0 Reset the POE reset 1 Controller VEG 172485322220 poeSystemActionHubRestoreFactoryDefault INTEGER ready 0 Restore Factory restore 1 Defaults 18012482 2280 poeSystemActionHubSaveconfiguration INTEGER ready 0 Save the POE save 1 parameters to flash Ve 24652 2 240 poeSystemAllPortPowerEnable INTEGER ee poeSystemHWVersion DisplayString ready 0 disable 1 enable 2 Setting this object at a value enable 2 enables detection mechanism for all ports Setting this object at a value disable 1 disables detection mechanism for all ports Read Only System hardware version for the main board eo poeSystemNumberOfchannel INTEGER Read only Number of ports available in the system 22 02
19. IHONG jue iset CBC DES ne set privacy encryption to CDC DES or CFB User definied password may be left blank or 1 18 characters in length If changed teh informaiton should be written in a Privacy Password ELG safe place for future reference This option may be used in place of the Community String 0 0 0 0 Trap Hosts are the destination IP addresses that you want EE 0 0 0 Gan Traps to be sent to Trap Hosts ED 0 0 0 Ge Be So 0 0 0 NOTE Trap Notifications are black from entering through the Windows Firewall Please configure the Windows Firewall settings to allow incoming Network Connections by adding a specific program i e the SNMP Console If the user is using the Authentication and Privacy passwords they must remember these to use the Phihong GUI Open the Phihong GUI and locate and click setting Figure 37 GUI Connection Information Connection Information Connection Type SNMPILAN amp WAP Search PoE A pop up for the User Security Parameters will allow you to enter the correct IP Address of your midspan If the user is using the Authentication and Privacy Passwords ensure that SNMPv3 is checked and enter in the correct passwords in the spaces provided The default passwords for both are 12345678 Ensure that the User also matches the name entered in the Controller Setup js 38 GUI User Sou Parameters Uft Lali IP Address 192 168 31 12ll
20. PC and the Midspan is adequate the Ethernet Manager tool will detect your SNMP device Figure Ethernet Manager ae Ethernet Manager Wiew Config IP Address Subnet Mask HAC Address Device ID 192 168 31 121 255 255 255 H BH 801 3D 82 BB BR Devices detected 1 5 If your device is not found check the connection and click View Refresh Ethernet Manager m x SM Config Subnet Mask MAC Address Device ID 1 255 255 255 0 HB 81 3D 3 2 dB Bh 1 Devices detected 1 Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 28 PHIHONG 2 Advanced Setup Options For Advanced Setup Configuration click Config Device Settings OR type the IP address in your Internet Browser Your Internet Browser will open with the following window Figure 31 Controller Login Configuration Microsoft Internet Explorer ER File Edit View ae u u dia x Back e x BE p J Search Hr Favorites v a Address httpi 192 168 31 121 Login IP MAC Firw v Go Favorites Tools Help Links 3 Google Be PHIHONG Power Over Ethernet Controller Status IP Address 192 168 31 12 MAC Address 00 01 3D 82 00 BA Firmware Release Ver 1 0 2008 Mar 6 Setup Login __ a Internet Click Setup Login Default User ADMIN Default Password leave area bla
21. apie 1 EDNA dM eceeaees 12 Table 2 Electrical Specifications waren EEE EN EN EE 14 Table gt ITOUDIESNOOLNG EE T T 25 Table 4 DC Specifications zur Ur ku todUna esp iut EE UMeOdenc DIM MUN NX Scdc PIENSO NU TK UNEUES 26 zio feo anre NN 32 Table G SNMP OG Bd S RTT 35 Table 7 SNMP MIB OM ONG EA T TTE 41 Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 5 1 1 1 PHIHONG Safety Procedures General Precautions General Please read the following precautions carefully before installing and connecting the system to a power source Note Only qualified and trained service personnel in accordance with IEC 60950 and AS NZS 3260 should install replace or service the equipment Install the system in accordance with Country National or to the U S National Electric Code if you are in the United States Precautions 1 The building facilities in which the product will be used requires a fuse or circuit breaker no larger than 15A for 120Vac U S A or 10A 230Vac international The building facilities must protect the Midspan from over current or short circuits Before connecting the Midspan to a power source including power cord requirements read the Midspan Hardware Setup procedure in Section 2 This procedure as with all procedures and instructions can be found in th
22. cusecenecnesoasecuescesecuseceseceeeseaesoess Figure DS SIO een coe esate aE co Fig re 16 Device Manager je Figure 17 PC to Midspan Connection via USB RS232 enernnnennnnennnrnnnnrnnnnnnnnnennnvennnnnnnnnnnnnennnnennnne Figure 18 Prolific USB to Serial Com Port General Properties rrnnrnnnrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnne Figure 19 Prolific USB to Serial Com Port Advanced Properties eeeseeeeseese FUEL TET Figure 21 GUI Main Window Mem ES Figure 22 GUI Connection Information NET Figure 23 System Setup Control System Information and Port Commands Figure 24 System Update SE T S FEL F OF SN Figure 26 LED Key Port Status Landis Figure 27 Parametric Information runs Flere PONTA Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 4 PHIHONG Figure 29 PC to Network to Midspan 2 22002400200000000nnnnnnn anno anno annnnnnn nenn nnnnnnnnnnnn anne nnnnnnnenenn 27 Fig re 30 Ethernet Manger NE een 28 OE Oro aii se gi EOGI e OTT 29 Figure 32 Controller Main Window cccccccssccsecceecceeeeceeeceecaeeceuecaeeessseseeceuecauecsueeaueeseeeseessaeesaess 30 Figure 33 Controller System Administration u serie 31 Figure 34 C
23. e 9 USB Cable Figure 10 USB Cable Connected AC power cord The AC power cable is connected to the AC power connector located in the rear side of the Midspan and the power outlet Figure 11 AC Power Cord Ethernet and USB cables are not included AC power cord may be ordered seperately Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 10 2 5 PHIHONG Powering UP Midspan receives power via the power cord In order to apply or remove power to from the Midspan connect or disconnect the AC power cable to from the AC power connector on the rear side of the unit With AC power applied the unit starts up and the internal fans are active The device runs through a quick power on test which takes less than 10 seconds During this period all ports are initially disabled and the port indicators light up The sequence of the port LEDs are shown in section 2 6 LED Indicator Cold Start Ports are now operating under normal conditions 2 06 LED Indicator Cold Start a AC LED turns green remains on b NIC LED turns green red green turns off red turns off unless connected C 24 Ports with ports connected LED turns orange green orange green turns off LED turns green individually ports 1 9 17 ports 2 10 18 ports 3 11 19 ports 4 12 20 ports 5 13 21
24. e Midspan User Manual To download a copy of the Manual visit www phihong com To prevent the Midspan from overheating do not operate the product in an area that exceeds the maximum recommended ambient temperature of 400C Allow at least 3 to 4 inches of clearance around all ventilation openings In order to Support the Midspan weight do not stack the chassis on any other equipment Shelf mounted equipment requires a stable and durable surface When installed do not push or pull on the Midspan when the equipment is installed The Midspan consists of two rows of Data and Data amp Power ports The ports use RJ 45 data sockets Do not connect telephone cables into these ports Only RJ 45 data cables may be connect to these sockets Do not work on the Midspan system or connect or disconnect the cables during periods of lightning activity The AC or DC plus socket combination must be accessible at all times as it serves as the main disconnect device to the product Before servicing the product always disconnect the products from its AC and DC source Disposal of this product should abide by all appropriate National laws and regulations Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 6 1 1 PHIHONG SicherheitsmaBnahmen Allgemeine VorsichtsmaBnahmen Allgemein Lesen Sie die folgenden Vorsichtsma nahmen sorg fltig durch b
25. emont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com AG
26. entStatusclear porPortDescription KKK poePortDetectionStatus KKK poePortPowerClassifications poePortPowerDetectionControl KKK powPortPowerPriority INTEGER DisplayString SIZE GO INTEGER INTEGER INTEGER INTEGER Read Write Read only Read only 1 Critical High 2 Low 8 Setting the value of this object to clear 2 clears the value of the poePortStatus and enables the agent to update the poePortStatus During Read operation this value will be off 1 Describes the port descriptionfor the port Off 0 DiscR 1 DiscC 3 HampUp 4 RampDown 5 Samplel 8 SampleV 9 ClassO 1 Class1 2 Class2 3 Class3 4 Class4 5 Command controls the port power detection control Sets port priority 1 3 6 1 4 1 24852 2 3 1 11 1 24 powerPortPower INTEGER Read only Port Power reading in mWatts 1 3 6 1 4 1 24852 2 3 1 12 1 24 poePortVoltage INTEGER Read only Port Voltage reading in Volts 2 0 1 1 2285272575137 NEGER OLE INTEGER Read only Port Current reading in mAmps 1 3 6 1 4 1 24852 2 3 1 14 1 24 poePortResistance INTEGER Read only Port Resistance read in Ohm 1 3 6 1 4 1 24852 2 4 1 1 1 24 1 3 6 1 4 1 24852 2 4 1 2 1 24 poelrapsControlGrouplndex poelrapsControlEnable INTEGER 0105535 INTEGER Not accessible TrapsDisabled 1 TrapsEnabled 2 Uniquely describes the group the Trap control is located Enables and disables the Tra
27. evor Sie das System installieren und an eine Energiequelle anschlie en Hinweis Das Ger t derf nur durch qualifiziertes und geschultes tehisches Personal gem IEC 60950 Vorschrift 60950 der Internationalen Elektrischen Kimmission und AS NZS 3260 Vorschrift f r Australien und Neuseeland installiert ersetzt oder repariert werden Installieren Sie das System auch in bereinstimmung mit den geltenden nationalen oder europ ischen Vorschriften bzw Der NEC Vorschrift falls Sie sich in den Vereinigten Staaten befinden Vorsichtsma nahmen 1 Die Geb udeinstallationen in denen das Produkt benutzt wird m ssen ber eine Sicherung oder einen Schutzschalter mit maximal 15A f r 120 Vac USA oder 10A f r 230Vac ineternational verf gen Dis Geb udeinstallationen m ssen das Midspan Device vor zu starkem Strom oder Kurzchl ssen sch tzen Lesen Sie vor dem Anschlie en des Midspan Device an eine Energiequelle einschlie lich der erforderlichen Anschlussleitungen die Setup Anleitung f r Ihre Midspan Hardware in Kapitel 2 genau druch Dieses Verfahren wird zusammen mit allen weiteren Vorg ngen und Anwisungen im Benutzerhandbuch f r das Midspan Device beschrieben Sie K nnen das Benutzerhandbuch unter www phihong com herunterladen Um das Midspan Device vor berhitzung zu sch benutzen Sie das Produkt nicht in R umen die die maximale empfohlene Umgebungstemperatur von 400C berschreiten Lassen Sie um alle L ftungs f
28. fnungen herum mindestens 7 5 bis 10 cm 3 4 inches frei St tzen Sie das Gewicht des PoE Midspan Device nicht ab indem Sie das Geh use auf ein anderes Ger t stellen Falls Sie das Ger t auf ein Gestell montieren muss dieses eine stabile und haltbare Oberfl che haben Nach der Installation des Systems bewegen Sie das Midspan Device nicht mehr Ds Midspan Device enth lt zwei Reihen mit Datenports und Daten und Stromports Die Ports verwenden RJ45 Datenanschl sse Schlie en Sie keine Kabel an und trennen Sie keine Kabelverbindungen w hrend Gewittern mit Blitzen F hren Sie an dem Midspan System keine Arbeiten durch schlie en Sie keine Kabel an und trennen Sie keine Kabelverbindungen w hrend Gewittern mit Blitzen Der Steckanschluss f r Gleich oder Wechselstrom muss jederzeit zug nglich sein da er als Haupttrennger t f r das Produkt dient Trennen Sie das Produkt immer erst von der Stromquelle bevor Sie Wartungs oder reparaturarbeiten daran durchf hren Entsorgen Sie dieses Produkt gem aller geltenden Gesetze und Vorschriften Ihres Landes und der EU falls Sie sich in einem Land der EU befinden Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com a7 PHIHONG 2 Midspan Hardware Setup 2 1 Physical Hardware Appearance Front Side of the Midspan Figure 1 The Midspan is not Connected AC LED HPS LED e
29. further technical assistance All up to date contact information can be found on our website www phihong com Table 3 Troubleshooting Problem Possible Solutions AC LED not lit Verify Midspan is properly connected to an AC power source The GUI window does not update Click System Reset and wait for the port status System to Reboot Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com DB PHIHONG Appendix A Optional RPS option R Please contact Phihong Sales for more information Figure 28 DC Power Connector 47VDC to 57VDC 47VDC to 57VDC 47VDC to 57VDC EM Not Used Figure 5 DC Power Connector 6 47VDC to 57VDC DC IN Molex 6 pin p n 39 30 0060 or equivalent DC IN Mate Molex 39 01 2065 pin p n 39 00 0077 Specifications DC Input Voltage Range R option 47VDC to 57VDC POE370U 15 4W Output power per port POE576U AT 33 6W POE76U AFAT Ports 1 8 33 6W 9 24 15 4W Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 26 PHIHONG Appendix B Optional NIC Interface Option N PC to Network to Midspan Figure 29 PC to Network to Midspan Diagram Cat 5e Cable POE576U 16AT N Network Switch Management PC POE576U 24AFAT N Cat 5e Cable NIC Interface Se
30. i Class Current Determined Class Port 20 Port 21 Port23 Port 24 Por 13 Port 14 Port 15 Port 16 Porti Port 18 Port 19 Port 2 Discovery R Discovery C Current m voltage v Power mw Class Current Determined Class gi The Port Parametric Information panel has the following set of parameters that are displayed e Discovery R ohms This value represents the discovered resistance R of the port in ohms e Current mA This value represents the current I of the port in milliamps e Voltage V This value represents the voltage V of the port e Power mW This value represents the power of the port in milliwatts e Class Current mA This value represents the class current of the port in milliamps e Determined Class This value represents the class of the discovered device Note If the ports are less than 24 ports for the system those ports greater than the total system port count will read all zeros O In the figure above Port 1 is connected to a compliant load while Ports 2 24 are ready to be connected Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com D PHIHONG 5 Troubleshooting If problems occur with the Midspan verify the following The troubleshooting solutions provided can only solve minor problems If your problem is not listed please contact our Phihong Sales for
31. idspan USB Port PC Internal Function The PC automatically detects Connects USB Port PC to the newly installed hardware This function is called Plug device Midspan via USB Cable amp Play available with a USB connection Internal USB device Midspan The PC quickly identifies teh sends a signal to your PC connection as Serial Com creating a Virtual COM Windows will automatically Port A Virtual COM Port install your device on an corresponds to a serial available serial COM port communication port Changes may be made via Device Manager section 3 2 discusses Device Manager Wait for the PC to respond Note Assume USB to Serial Com Port driver is installed Users PC will automatically detect the newly installed connected hardware Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com i8 PHIHONG 4 Midspan GUI The firmware is supplied with a Graphical User Interface GUI which is used to configure and manage the PoE midspan system If you have successfully installed the Phihong GUI and USB driver Please locate the Phihong Midspan POE GUI on your desktop or from your Start Menu le Phihang POE SNMP YS GUI 4 1 GUI Main Window Step 1 Choose connection type I mung vosas roco RR as System Information Operation Reset Update System Port Param System Information Connection Information
32. mware Update a E LEM WU F F ais LE YS am Yr L32 868 31 121 ey Choose file vs om oe ER Ty Bookmarks BD HP Ber 23 z PaEE7 FirmwareuDo 051503 9 ROM bin Look in ip POES Recent s Caution improper operation may Cause permanent damages to your device Please da not remove the power of the device or close this window during updating a It will take several minutes to run and should not be interrupted m et Fila nana AN Fikes I Click browse then locate your firmware file it will have a bin file extension Then click update Firmware file example ROM bin 4 096 KE BIN File 12912009 10 42 AM Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com Eeee PHIHONG Restore Default Settings This function is used to revert back to the default settings for the Firm ware This will undo any changes that you ve so far made to the Firmware configuration After using this function users will have the option to go back or to reboot their system Reboot System This function will reboot the system This screen will display Please wait 15 seconds while the system Is rebooting Once the system has finished rebooting it will revert back to the GUI Main Screen Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1
33. net mask and Gate way address If the DHCP client is set to disable the DHCP BASE GJEN SE SE client is set to Static mode Static mode al lows teh user to manual assign the IP ad dress subnet mask and Gateway Address Note If the user manually assigns the IP ad dress the DHCP client must be set to Dis able Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 30 PHIHONG System Tools Firmware Backup click the Backup button and you will get a pop up to save a BIN file of the current Firmware and settings Save in a location that will be easy for you to remember and the file may be renamed to user specifications File Download Do you want to save this file E Name ROM bin Tupe Unknown File Type 4 00 MB From 192 168 31 121 T While files from the Intemet can be useful some files can potentially harm your computer IF you do not trust the source do not save this file What s the risk DHCP Client Enable Firmware Backup Firmware Update Figure 34 Controller Firmware Backup Firmware Update click Update to install the most recent firmware for your midspan or to re install a firmware that was backed up Before proceeding with this step users should ensure that the connection between the PC and Midspan is secure and will not be interrupted as this may take a few minutes Figure 35 Controller Fir
34. ng on the connection speed Check the Midspan IP Address again as it may have change depending on the user settings for DHCP Client Click to review or make additional changes Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com Aj PHIHONG Configuration Description Table 5 Controller Setup Controller Setup Default Settigns The login administrator is a user defined name that is used at login Please write down Adminstrator Admin your new login name in a safe location for fu ture use The login password can be empty or 1 14 characters long Please write down your new Password Blank password in a safe location for future use The password is also used while performing SNMP Firmware updates Four groups of numbers assigned by the net IP Address 192 168 1 111 work server DHCP mode Enabled or User defined DHCP mode disabled Four groups of numbers assigned by the Subnet mask 255 255 255 0 Network server DHCP mode enabled or user defined DHCP mode disabled Four groups of numbers assigned by the Gateway address 192 168 0 1 Network server DHCP mode enabled or user defined DHCP mode disabled DNS Server 168 95 192 1 Four groups of numbers assigned to the net Work server The default setting Enable sets the DHCP client in Dynamic mode Dynamic mode al lows the Network server to automatically as sign the IP address sub
35. nk NOTE If you forget your login password please contact Phihong Sales for further instructions For up to date contact information please visit our website www phihong com Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 200 PHIHONG 3 Controller Setup Figure 32 Controller Main Window E Configuration Microsoft Internet Explorer PENG File Edit View Favorites Tools Help A Qs T 38 E Search FF Favorites e E M a W gt i Address g http 192 168 31 121 sys Go Links Google v 89 Search o S der Sr v Bookmarks Check E AutoFill yy mr s Ar Sign In PHIHONG Device Configuration gt Port Status Enabied Votage Samen Power Suas Pon Eratied vatge curent Power Ses i o I 2v oma om norma B om 24 om Omi omar ef o 2 om om nome fa on ov oma Dmw Noma ef o ov om om nome fa on ov oma om Noma af o av om omm nome fv om zv oma bmw Mama ef o av om im nemne f cn av om amn Nama ef o 2 om me noma fa cn zv um omw koma en 3M md Gin Nomad Lg o 4 imp Gom Numa an on ov om om Neal Ls o 4 imp omm moms 28 on ov dm Om Nera Em o 24 oma Bm moms zm On og omA Om Nera Ew on 2 um om nome m o ed o 4 vm om teme Ra om Port Command Port Enable vi v Internet Port Status
36. nnnnnnen 5 Setup NIC Midspan with Phihong GUI an ee een ee C SNMP MIB OB D Frequently Asked Questions rrnnennnnennnnennnrnnnnrnnnnrnnnnrnnnnennnnennnnennnennnnennnnennnnennnnennnnnnnnrnnnnennnne Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com s PHIHONG Figure 1 Midspan is not connected EEE List of Figures Figure 2 Data amp Power top row Data bottom row EE Figure 3 Connectors and Indicator 2z 024202000000002000nnnnnnnnnnn anno nnnn nun nun anne nnnn anne anne nun nnnn nennen FOLIO Rear Side NNN ee Figure 5 DC Power Connector Jar Figure 6 AC Power Connector anrrnnrrnnnnnnnnnnnnrnnnnnnnrnnnnnnnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnrnnnnnnnennnennnnnnnennunennnen Figure 7 Midspan connected through Data amp Power line rrnnrnnrnnnrnnnnnnnnnnrrnnnnnnnnnnnnnnnnnnnnnnnnenne Foe NIS Ce A OQ Figure 9 USB Cable EEE Figure TO USB Cable Connected ze ee ee ee suede Ner Siu mean Figure i Mey Ora ke i es Figure 12 Rack Mounted Midspan aranrnnnnnnnnnnnnnrnnnnnnnnnnnnnnnnnnnnnnnnunnnnnnnrnunnnnnnnnnnnnnnnnnnnvnnannnennnnnunane Figure 13 Hack Mounting Bracket and Screws une LGG cies sndgesiadionseicleienades Figure 14 Technical Specifications ccccccceeccceecceneceeecencececccess
37. of 254 168 2 xxx Different methods of connection NOTE Taking consideration that the Access Control from the Controller Setup is Disabled allowing all access Connection within the same Network Domain Please refer to the diagram above for Building 1 For instance The NIC Interface Midspan is connected to the Network Domain of 192 169 1 xxx located on the 1st floor All Computer connected to the Network Domain of 192 168 1 xxx can communicate with the NIC Interface Midspan The NIC Interface Midspan remains connected on the Network Domain of 192 168 1 xxx Since Building 1 has a main Network Server that links all three floors together the computers on the 2nd 192 168 2 xxx and 3rd 192 168 3 xxx floors can also communicate with the NIC Interface Midspan Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 45 PHIHONG Connection between different Network Domains Please refer to the diagram above Building 2 For instance The NIC Interface Midspan is connected to the Network Domain of Building 1 192 168 1 xxx would like to communicate with the NIC Interface Midspan from Building 1 Building 1 must configure the main Network server to allow access from an outside source in this case Building 2 Building 1 must be able to support UDP port 161 for SNMP Once the access is allowed Building 42 can communicate with the NI
38. ontroller Firmware Backup 22 02200240020000000 0000 Bann anno ann anno anne nun nenn rene nane nein nasa nsn eser 33 Figure 35 Controller Firmware Update 022u0240020000000 0000 anne nano anno nnnnnnnn senes nannten 33 Figure 36 Controller SNMP Settings re 35 Figure 37 GUI Connection Information USB x2xsaicsxcs axkeszdksbxt xexc kxFE auditus dir uiips desino wipe en en 36 Figure 38 GUI User Security Parameters rrnnnnnnnnnnnnnnnnnnnnnnnennnnennnnnnnnrnnnnrnnnnennnsennnnennnennnnennnnennnne 36 Figure 39 Ethernet Manager Set IP Address r nnnnnnnnnnnnnnnrnnnrnnnvnnnnnnnnnnnnrnnnrnnnnnnnnnnnnnnnnnnnnnnnnsnnsnnnee 37 Figure 40 Local Area Connection Status 22u0024002000 n00 0000 anne nnnnnnnnnnnnnnnnnnnnn nenn anne nnnnnnnnnnnnnnnenenn 38 Figure 41 Local Area Connection Properties Internet Protocol Properties 38 Figure 42 GUI User Security Parameters rrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnnnrnnnnnnnnnennrnnnnennnnennnne 39 Figure 43 GUI User Security Parameters Ethernet Manager 2 022402200020002000nnno nenn nenn nennen 39 Figure 44 GUI Connection Information SNMP u2220022002000200000n0nnnn nenn anno anno nee nnne nnn nennen 40 ROE GU Man VULGO ne 40 Figure 46 Network Domain Diagram ennnnuvnunnnnnnvnnnnnnnnnvnnnnnnnnnnnnvnnunnnnnnnnnunnnnnnnnnvnnannnennnnnannnennnnnusane 45 List of Tables T
39. or www midspans com 20 PHIHONG Contents Safety Procedures 1 1 General Precautions ccccccccccccccucceccuccuccuauucuecuuaueuuuauuauenuuauenuunuuauuuuauenuunueuuuuueauauuuuusuusuunuusueans Midspan Hardware Setup 2 1 2 2 2 3 2 4 2 9 2 6 2 1 2 8 Physical Hardware NNN Power Cord RENN Connecting Ethernet Cables EN Connecting USB and Power Cables sea ee ee PFIN FONN Rack Mounting Installation ee E mS Technical PENNE d PO Phihong GUI and USB Driver Installation 3 1 3 2 3 3 PC to Midspan Connection via USB RS232 rrrannnnnnnanennnnnnnrnnnrennnennnennnennnrnnnrnnnnennnennnennnennn Device Manager To View Port Properties rrnnrnnrnnrrnnnnnnnnrrnnrnnnnnnrnnnnnnnnnrnnnnnnnnennvnnunnunnnennuene VER PO NNN NP nern nee ee ne lernen Midspan GUI 4 1 4 2 4 3 4 4 SUNE VNR GUI System LNM GUI Port Description MENT T GUI Parametric seen Dm Midspan Troubleshooting arrnnrnnrnnnnnrnnrnnrnnnnnnnnnnnrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennene Appendix P OBLONal APS PAN are ee B Optional NIC Interface option N 1 MENN 2 FOTNOTER S URAN RN T anne ee ner 3 1 System Administration 22200000020002000 0000 anno Bann anne ann anne anno nen nnnnnnnnnennn anne nennen 2 PINE zen ee ee EP 4 DHCP Client Dynamic and Static Mode Setup rernnrvrnnrernnrevnnrnvnnrnnnnennnnennnnennnnnnn
40. p 1 3 6 1 4 1 24852 2 5 1 1 3 6 1 4 1 24852 2 5 2 from the Agent poePortHWfFailTrap NOTIFICATION Hardware Failure Trap poePortPeakOverCurrent Trap NOTIFICATION Peak over Current Trap Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 43 PHIHONG S ASS poePortOverloadTrap NOTIFICATION Overload Trap 1 816 ESP 2505 poePortDisconnect Trap NOTIFICATION PortDisconnectTrap This function is currently disabled Reserved for future use 1 The NIC Interface Midspan performs under the TCP IP UDP port of 161 UDP port 161 for SNMP is an official IANA registered EDP port number While attempting to connect to the NIC Interface Midspan via a different network domain2 the user must acknowledge that the local network supports the UDP port 161 Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 44 2 Building 2 Network Domam PHIHONG Different Network Domain Figure 46 Network Domain Diagram 254 168 2 xxx Network Domain 3rd floor 192 168 3 xxx Znd floor 192 168 2 xxx lst floor 192 168 1 xxx Building 1 Network Domain 192 168 1 xxx Description of Diagram Building 1 has on main Network Server that links all three floors together Building 2 has one main Network Server with the Network Domain
41. poration e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 14 PHIHONG 3 Phihong GUI and USB Driver Installation Please locate and download the file Phihong GUI Installation from the support section of the Phihong websites www midspans com or www phihong com Please follow the Installation Wizard to install the Phihong GUI for your model and the USB to Serial Com Port driver The USB to Serial Com Port driver is necessary for communicating between the Midspan via a Communication Port on the PC 5 Example of the Phihong MI Setup File DSPAN POE Figure 15 GUI Setup Welcome to the Phihong MIDSPAN POE GUI 1 0 Setup Wizard This wizard will guide you through the installation of Phihong MIDSPAM POE GUI 1 0 It is recommended that you dose all other applications before starting Setup This will make it possible to update relevant system files without having to reboot your computer Click Next to continue Note Please refer to the Phihong website to insure you are installing the latest version of the Phihong GUI The example shown is using the Midspan POE GUI 3 1 PC to Midspan Connection via USB RS232 Figure 16 PC to Midspan Connection Diagram ee USB Cable Midspan p Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 15 PHIHONG 3
42. r must click Save Parameters to Flash If Detect Legacy Signature checkbox is selected all ports are enabled and the firmware will try to detect legacy devices By default legacy detection is disabled The message in blue states that the Legacy Detect is Enabled Figure 16 Click Send Port Control to send the command to the system To make this permanent the user must click Save Parameters to Flash Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com p PHIHONG The different colored LEDs show the status of the individual ports A Yellow LED shows the port is detecting or ready to be connected A Red LED shows the port as Disable Error A Green LED shows that the port is connected to a compliant load Figure 26 LED key Port Status LED Key Port status Detecting Disable Error Port Connected Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 0 PHIHONG 4 4 GUI Parametric Information This section allows users to review but not edit Parametric Information for each port Fiqure 27 Parametric Information Port Deseription Parametric Information Port I Port 2 Port 3 Port 4 Port 5 Port 5 Port 7 Port 8 Port 9 Port10 Port 11 Port 12 Discovery R Discovery C Current m Voltage v Power m
43. rea when connected v Notify me when this connection has limited or no connectivity Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com 38 PHIHONG 5 Setup NIC Midspan with Phihong GUI Please locate the Phihong POE GUI on your desktop or from your Start menu Step 1 Choose Connection Type SNMP LAN amp WAN and click to access User Security Parameters Users should be aware to input the exact device IP Address Figure 42 GUI User Security Parameters User Security Parameters IP Address EE 168 31 101 Read Community public Set Community private O SNMP3 SNMP33 jadmin User admin AuthPassword PrivPassword eum NOTE Ensure that you are using either the community string or SNMPv3 encrypted passwords set using the Controller System setup or the GUI will not detect the midspan To verify the IP Address for your midspan use the Ethernet Manager tool mentioned in earlier sections The default password for both AuthPassword and PrivPassword is 12345678 Users may change these using the http access described in section 2 of Appendix B Advanced Setup Options Figure 43 GUI User Security Parameters Ethernet Manager User Security Parameters fx gt Ethernet Manager View Config IP Address EF 168 31 101 i Subnet Hask MAC Address Device ID 192 168 31 121 255 25
44. ry upon user Prolific USB to Serial Comm Port COM 7 Properties 7 Ex General Port Settings Driver Prolific LS B te S ernal Comm Port COM 7 Device lupe Ports COM amp LPT Manufacturer Prolific Location Location E US6 Senal Controller Di Figure 18 Prolific USB to Serial Com Port Properties General Settings Click Pat Settings assure Port Setting is as shown Click Advanced Click the pull down menu and select the Com Port Number or stay with the default Prolific USB to Serial Comm Port COM Properties EE Advanced Settings for COM General Port Settings Driver Use FIFO buffers requires 16550 compatit Bits per second 19200 y Select lower settings to correct connection Select higher settings for faster performanc Data bits 8 v i Receive Buffer Low 1 Parity Mone vw Stop bits 1 IT Transmit Buffer Low 1 j qp Flow control an Xoff w COM Port Number COM v Restore Defaults Figure 19 Prolific USB to Serial Com Port Properties Advanced Settings Click to save all changes Notes Users should write down the Com Port number as the GUI will need to know the exact port on which to search for devices Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com AT PHIHONG 3 3 USB Block Diagram Figure 20 USB Block Diagram USB Device M
45. tup NOTE Assure the connection path between your PC and the Midspan Skip Step 1 if you with to use our Phihong GUI to communicate with the Midspan 1 Visit www midspans com to download the latest SNMP MIB for the NIC interface Example SNMP MIB file please check our website for updates phihong060809 txt 13KB Text Document 6 9 2006 9 11 AM If you choose to use your own SNMP console please rename the SNMP MIB text file to the file extension that matches your SNMP Console Follow the instructions for your SNMP Console to install the MIB file Please check the Phihong website www midspans com occasionally for the latest updates for the MIB and SNMP Firmware Example of a SNMP Firmware file please check out website for updates ke 0608095973 b14 3 bin 58KB BIN File 8 9 2006 9 11 AM 2 Visit www midspans com to download the Ethernet Manager tool etm exe Etm exe is a Device Management Utility that runs under the Windows 32 bit environment and is used to setup the IP address subnet mask and MAC address of your SNMP device For more advanced setup settings use Internet Explorer or another Internet Browser Phihong USA Corporation e 47800 Fremont Blvd Fremont CA 94538 e Tel 1 510 445 0100 Fax 1 510 445 1678 www phihong com or www midspans com D PHIHONG NOTE Your IP Address may be different from the example shown below 3 Execute etm exe Ethernet Manager tool 4 Assuming the connection path between your
Download Pdf Manuals
Related Search