Edimax 2 Ports PS/2
Contents
1. ScrLk Q any PC and Audio Mic switching are bound together To remove this binding hit ScrLk ScrLk W Hotkey convention The hotkey notation key denotes that you should hit the individual key consecutively one at a time not simultaneously Mouse Troubleshooting If your mouse hangs or behaves abnormally you can hit the following hotkey commands for mouse reset a When you are using a PnP OS such as Windows 98 Second Edition or later Windows operating systems such as Win2k WinXP etc hit for mouse reset b When you are using a non PnP OS such as Linux NT4 0 etc just hit one of the following hotkey commands for mouse reset according to your mouse configuration on the non PnP OS M 1 for a 2 key mouse setting M 2 for a 3 key wheel mouse setting M 3 for a 5 key wheel mouse setting2. EDIMAX NETWORKING PEOPLE TOGETHER EK PSK2 EK PSK4 EK PAK2 EK PAK4 2 4 ports PS2 KVM Switches Quick Installation Guide The Edimax KVM switch series is a 2 4 port Slim Palmtop PS 2 KVM Switch with optional audio and microphone switching function It allows you to access control boot and reboot multiple PS 2 enabled computers using only one keyboard video mouse and optional speaker set and microphone It also offers user programmable simultaneous independent switching of PC channel and Audio Mic channel for flexible multimedia application with KVM switching For users who might need to use a hotkey preceding sequence other than two scroll locks we also offer five key alternatives for free configuration The default setting of the KVM switches is appropriate for most systems The KVM Switch is a Plug and Play device for installation In fact you do not need to configure the KVM Switch before installation For the first time installation of the KVM Switch please follow the instructions below for correct setup sequence Np The correct setup sequence is 1 Connect the shared keyboard monitor and mouse and optional speaker set and microphone to the KVM Switch first and then connect your computers 2 Power up your connected computers Since the KVM Switch receives power from the computer s PS 2 interface it is powered up when you connect the KVM Switch to a PC Take the KVM Switch out of the box an
3. d begin installation N DO NOT TRY to connect the KVM Switch to the computers while the computers are still in pbowered on states Otherwise the computer will have difficulty recognizing your shared keyboard and mouse Step 1 Make sure all the computers that are to be connected to the KVM Switch and their peripherals are in powered off state If not power them off before you proceed with the following steps Step 2 Connect the shared PS 2 keyboard mouse monitor speaker set and microphone to the KVM switch Step 3 Connect each of your computers to the KVM switch using appropriate KVM amp Audio Mic cables Configuration Diagram Step 4 Now your KVM Switch should have been powered up Power up the connected computers one by one After your computers are powered up the keyboard and mouse will be recognized and now you can begin operating the KVM switch There are two methods to control your KVM Switch for PC switching using the face panel push button or a hotkey sequence For audio mic switching use the hotkey command See Quick Reference Sheet Face panel buttons The face panel buttons allows you a direct control over PC port switching Simply press the b
4. ect PC amp Audio Mic port if binding is enabled Enable the binding of PC and Audio Mic switching Once this feature is enabled PC and Audio Mic switching is bound together factory default Select the next lower PC channel joint select PC port and Audio Mic port if binding is enabled Select the next higher PC channel joint select PC port and Audio Mic port if binding is enabled is enabled Backspace P H y SCROLL LOCK CAPS ESC F12 or NUM LOCK Press and hold down last button Button 2 Butotn4 till two beeps release the button and then press y key keys Console Mouse Keyboard Reset gt Reset keyboard and mouse on the console side ea Auto scan through every connected channel for quick screen ee Si See Scta E g browsing of each channel scan delay 5 sec S a l l l T A toscan with Proarammable Delay Time x 0 9 _ Auto scan with a user defined delay time within a range of 5 g y 1310 2 gt 20 3 gt 30 4 gt 40 5 gt 50 100 seconds 6 gt 60 7 gt 70 8 gt 80 9 gt 90 0 gt 100 Terminate Auto scan activity Stop Autoscan Press any key on keyboard Press any button Notes 1 Note that x denotes a number key for the selected port number x 1 2 You can use either the top row number keys or the number pad for the hotkey commands 2 When the binding of PC amp Audio Mic port switching is enabled by the hotkey sequence ScrLk
5. ey configuration mode Then you select and press the key that you ll choose as the preceding sequence M Each keystroke within a hotkey sequence should be pressed within 2 seconds Otherwise the hotkey sequence will not be validated NE Eor detailed Hotkey sequences and their corresponding functional commands please refer to the Quick reference sheet Quick Reference Sheet 2 4 port Slim Palmtop PS 2 KVM Switch Operation Commands for Hotkeys Face Panel Buttons Hotkey sequence ScrLk ScrLk Command key s User definable Preceding sequence SCROLL LOCK CAPS ESC F12 or NUM LOCK Command Hotkeys Face panel Buttons Description eect Channel L x Select the active PC channel Joint select PC port and Audio Mic port if binding x is a top row number key Joint select PC amp Audio Mic port if binding is enabled X 1 2 or1 4 for PC channel no ScrLk ScrLk Fx is enabled Bind PC amp Audio Mic Switching default Next lower PC channel Joint select PC port and Audio Mic port if binding is enabled Next higher PC channel Joint select PC port and Audio Mic port if binding Fx is a function key x 1 2 for Audio mic channel no ScrLk ScrLkj Q ScrLk ScrLk Wi i arrow up i arrow down Press the face panel button to switch to next PC channel Press the face panel button to switch to next PC channel1 Select the active Audio Mic channel Joint sel
6. utton to switch PC port By default PC port switching and Audio Mic port switching are bound together both will be switched simultaneously If you want to enable the binding of PC and audio mic port switching use the hotkey sequence ScrLk ScrLk Q To disable the binding again just hit ScrLk ScrLk W See Quick Reference Sheet Keyboard hotkey A keyboard hotkey sequence consists of at least three specific keystrokes See Quick Reference Sheet Hotkey sequence ScrLk ScrLk Command key s User definable SCROLL LOCK CAPS ESC F12 or NUM LOCK Hotkey preceding sequence configuration For users who want to use a preceding sequence other than two consecutive Scroll Locks there is also one convenient way to configure it Step 1 Hit ScrollLock ScrollLock H then two beeps will signal readiness for new preceding sequence selection or Press and hold down the last front panel button Button 2 or Button 4 until you hear two beeps and then release the button Step 2 Select and press the key you would like to use as your preceding sequence SCROLL LOCK CAPS ESC F12 or NUM LOCK keys are available for selection and you ll hear a beep for selection confirmation Now you can use the new preceding sequence to execute your hotkey commands Np Another way to activate the Hotkey preceding sequence configuration is to press the last front panel button button 2 button 4 for over 3 seconds to set the KVM switch into hotk
Download Pdf Manuals
Related Search