Tripp Lite OmniSmart Line Interactive UPS
Contents
1. may cause interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference using one or more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and the receiver connect the equipment into an outlet on a cir cuit different from that which the receiver is connected consult the dealer or an experienced radio television technician for help The user must use shielded cables and connectors with this product Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC rules Operation is subject to the following 2 conditions 1 This device may not cause harmful interference and 2 This device must accept any interfer ence received including interference that may cause undesired operation FCC PART 68 NOTICE UNITED STATES ONLY If your Modem Fax Protection causes harm to the telephone network the telephone company may temporarily discontinue your service If possible they will notify you in advance If advance notice isn t practical you will be notified as soon as possible You2. AC outlet Your warranty will be voided if anything other than Tripp Lite surge suppressors are used to connect your UPS to an outlet If the UPS receives power from a motor powered AC generator the generator must provide clean filtered computer grade output Equipment Connection Warnings Do not use Tripp Lite UPS Systems for life support appliances in which a malfunction or failure of a Tripp Lite UPS System could cause failure or significantly alter the performance of a life support device Do not connect surge suppressors or extension cords to the output of your UPS This may damage the UPS and will void the surge suppressor and UPS warranties Battery Warnings Your UPS does not require routine maintenance Do not open your UPS for any reason There are no user serviceable parts inside Batteries can present a risk of electrical shock and burn from high short circuit current Observe proper precautions Do not dispose of the batteries in a fire Do not open the UPS or batteries Do not short or bridge the battery terminals with any object Unplug and turn off the UPS before performing battery replacement Use tools with insulated handles There are no user serviceable parts inside the UPS Battery replacement should be performed only by authorized service personnel using the same number and type of batteries Sealed Lead Acid The batteries are recyclable Refer to your local codes for disposal requirements or in the US
3. it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that the compliance with the above conditions might not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate REGULATORY COMPLIANCE IDENTIFICATION NUMBERS For the purpose of regulatory compliance certifications and identification your Tripp Lite product has been assigned a unique series number The series number can be found on the prod uct nameplate label along with all required approval markings and information When requesting compliance information for this product always refer to the series number The series num ber should not be confused with the marking
4. name or model number of the product Tripp Lite has a policy of continuous improvement Product specifications are subject to change without notice Note on Labeling Two symbols are used on the label AC Voltage DC Voltage TRIPP LITE 1111 W 35th Street Chicago IL 60609 USA 773 869 1234 USA 773 869 1212 International www tripplite com 200607050 93 2490_EN
5. will be advised of your right to file a complaint with the FCC Your telephone company may make changes in its facilities equipment operations or procedures that could affect the proper operation of your equipment If it does you will be given advance notice to give you an opportunity to maintain uninterrupted service If you experience trouble with this equipment s Modem Fax Protection please call Tripp Lite Technical Support at 773 869 1234 for repair warranty information The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure the equipment is not malfunctioning There are no repairs that can be made by the customer to the Modem Fax Protection This equipment may not be used on coin service provided by the telephone company Connection to party lines is subject to state tariffs Contact your state public utility commission or corporation commission for information EQUIPMENT ATTACHMENT LIMITATIONS Models with the Industry Canada label in Canada only NOTICE The Industry Canada label identifies certified equipment This certification means that the equipment meets the telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements Document s The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that
6. A only call 1 800 SAV LEAD or 1 800 8 BATTERY 1 800 822 8837 or visit www rbrc com for recycling information Tripp Lite offers a complete line of UPS System Replacement Battery Cartridges R B C Visit Tripp Lite on the Web at www tripplite com support battery index cfm to locate the specific replacement battery for your UPS Do not attempt to add external batteries Quick Installation H Connect your UPS to an electrical outlet Your UPS will run a self test after it is e d plugged in See Basic Operation to understand the results of its self test o A Plug your computer monitor and other equipment into the UPS system Your UPS is designed to support only com puter equipment You will overload your UPS if you connect high power draw equipment such as household appliances or laser printers to outlets providing UPS battery backup Select models feature special outlets clearly labeled on the rear panel which provide surge only not battery backup protection designed for laser printers and other heavy draw devices El Select UPS Operating Mode Press the ON OFF button to toggle your UPS between the UPS V LED lit and the CHARGE ONLY LED flashing modes Choose the operating mode based on your location USA Canada amp Western Europe Leave the UPS in the UPS mode at all times All other countries Put the UPS in the CHARGE ONLY mode w
7. Oats atom J KETE F OMNISMART 7 Full Isolation UPS Systems Full Isolation Less than 300HA Leakage Line Interactive Operation e 120V Input FC Not suitable for mobile applications Tested To Comply With FCC Standards ea 2 KE 1 E Storage amp Service O EE Espa ol 9 Fran ais 18 C TRIPP LITE POWER PROTECTION 1111 W 35th Street Chicago IL 60609 USA Customer Support 773 869 1234 www tripplite com Copyright 2006 Tripp Lite All rights reserved OmniSmart is a trademark of Tripp Lite Important Safety Instructions SAVE THESE INSTRUCTIONS This manual contains instructions and warnings that should be followed during the installation operation and storage of all Tripp Lite UPS Systems Failure to heed these warnings will void your warranty UPS Location Warnings Install your UPS indoors away from excess moisture or heat dust or direct sunlight For best performance keep the indoor temperature between between 32 F and 104 F 0 C and 40 C Leave adequate space around all sides of the UPS for proper ventilation UPS Connection Warnings Connect your UPS directly to a properly grounded AC power outlet Do not plug the UPS into itself this will damage the UPS Do not modify the UPS s plug and do not use an adapter that would eliminate the UPS s ground connection Do not use extension cords to connect the UPS to an
8. e condition of the incoming voltage the VOLTAGE REGULATION LED may or may not be lit Basic Operation continued Indicator Lights All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on NDS LINE POWER This green light will turn ON whenever your UPS is receiving normal AC line power It will flash while the UPS is in CHARGE ONLY mode to indicate that the UPS will not provide battery backup during a black out or brownout BATTERY POWER This yellow light will turn ON when your UPS is pro viding your equipment with battery power BATTERY CHARGE This red light will turn ON continuously after the UPS runs a self test to indicate that the UPS s battery is weakly charged If it remains lit after you have allowed the UPS to charge for twelve hours and have run a second self test contact Tripp Lite for service OVERLOAD Select models only This red light will turn ON continuously when the UPS is providing power from battery or after the UPS runs a self test to indicate that the UPS s inverter is overloaded If it lights up immediately remove some of the equipment connected to the UPS and run a self test Large overloads may cause your UPS to shut down VOLTAGE REGULATION Select models only This light will turn ON when your UPS is automatically correcting high or low utility line voltage The UPS will also click gently when this automatic voltage regu lation is operating Th
9. ese are both normal functions of your UPS and no action is required on your part Other UPS Features DT C AC Receptacles UPS Surge receptacles are used to provide your con nected equipment with AC line power during normal operation and bat tery power during blackouts and brownouts They also protect your equip ment against damaging surges and line noise Surge only receptacles identified on the back of select UPS models are used to provide periph erals with surge protection without committing precious battery power to support them during blackouts Basic Operation continued USB Port The USB port connects your UPS to any USB workstation or server Using this port your UPS can communicate line fail and low battery status to your computer Use with Tripp Lite software and any USB cable to automatically save open files and shut down equip ment during a blackout Contact Tripp Lite Customer Support or con sult your power protection software manual for more information Battery Replacement Door Under normal conditions the original battery in your UPS will last several years Battery replacement should be performed only by qualified service personnel Refer to Battery Warnings in the Safety section Should your UPS require battery replacement visit Tripp Lite on the Web at www tripplite com support battery index cfm to locate the specific replacement battery for your UPS Power Sensitivity L
10. hen you are not using connected equipment WARNING When set to CHARGE ONLY the UPS will not provide battery backup during a blackout or brownout Put the UPS in the UPS mode when you are using connected equipment See Basic Operation section for a complete explanation of each mode Quick Installation optional USB Communication Port This port can connect your UPS to any computer for automatic file saves and unattended shutdown in the event of a power failure Use with Tripp Lite s PowerAlert Software and appropriate USB cable A PowerAlert CD and USB cable may be included with your UPS if so insert the CD into the CD tray of your computer and follow the instal lation instructions If PowerAlert Software and a USB cable did not come with your UPS you can obtain the software FREE via the Web at www trip Model Shown OMNIS00ISO plite com Any user supplied USB cable may then be used to connect your UPS to your computer NOTE This connection is optional The UPS will work properly without this connection Basic Operation Buttons Use the ON OFF button to do three things Switch your UPS s Operating Mode While your UPS is plugged into a live AC outlet press the ON OFF button and hold it until you hear a beep about 2 seconds to toggle between the following operat ing modes Choose your UPS s operating mode based on the regional guidelines in Step 3 of the Quick Insta
11. is button to silence the UPS On Battery alarm a series of short beeps followed by a brief pause that is activated when the UPS is providing AC power from battery Note When the battery is nearly depleted the Low Battery alarm a continuous beep that cannot be silenced will alert you to immediately shut down connected equipment Run a Self Test Your UPS performs a self test whenever it is first plugged in To have it run a self test at another time leave your con nected equipment on With your UPS plugged in and in the UPS mode press and hold this button until you hear a beep about 2 seconds then release it Results of a Self Test All the LEDs will be lit and the UPS will emit several short beeps as it momentarily switches to battery to test its charge and load capacity The test will last at most 10 seconds If the inverter is overloaded the 2 LED on select models will stay lit and the UPS will continue to beep after the test if this happens remove some of the load and run the self test again If the batteries seem weak the E21 LED will stay lit and the UPS will continue to beep after the test if this happens let UPS charge its batteries for 12 hours and repeat the test If the condition persists contact Tripp Lite for service CAUTION Do not unplug your UPS to test its batteries This will remove safe electrical grounding and may introduce a damaging surge into your network connections Depending on th
12. llation section UPS Mode ENABLES battery backup UPS Conditions The UPS charges its battery and supplies power at its receptacles when it is receiving utility line power If utility power fails the UPS provides power from its batteries The V indicator light is lit Setting Advantages Provides battery backup during blackouts or brownouts Basic Operation continued CHARGE ONLY Mode DISABLES battery backup UPS Conditions The UPS charges its battery and supplies power at its receptacles when it is receiving utility line power The V indica tor light is flashing Setting Advantages Continues to charge the bat tery when power is present while turning OFF the inverter to prevent battery depletion during power outages when equipment is not in use Cold Start Your UPS You may cold start your UPS and use it as a stand alone power source when utility power is not present providing that the UPS battery is charged To cold start your UPS press and hold the ON OFF button until you hear a beep about 2 seconds then release it The indicator light will illuminate and AC power inverted from stored battery power will be provided at its receptacles Shut Down Your UPS Press and hold the ON OFF button when AC line power is absent i e during a blackout or when the UPS is unplugged to deactivate your UPS Use the MUTE TEST button to do two things Silence the UPS On Battery Alarm Press and hold th
13. owline Adjustment select models only This dial is normally set fully counterclockwise which enables the UPS to protect against waveform distortions in its AC input When such distortion occurs the UPS will normally switch to providing PWM sinewave power from its battery reserves for as long as the distortion is present In some areas with poor utility power or where the UPS s input power comes from a backup generator frequent brownouts and or chronic waveform distor tion could cause the UPS to switch to battery too often draining its bat tery reserves You may be able to reduce how often your UPS switches to battery due to waveform distortion or brownouts by experimenting with different settings for this dial As the dial is turned clockwise the UPS becomes more tolerant of variations in its input power s AC waveform and reduces the voltage point at which it switches to battery NOTE The further the dial is adjusted clockwise the greater the degree of waveform distortion and the lower the input voltage the UPS will allow to pass to connected equipment When experimenting with different settings for this dial operate connected equipment in a safe test mode so that the effect on the equipment of any waveform distortions in the UPS s output can be evaluated without disrupting critical operations The experiment should last long enough to assure that all expected line conditions are encoun tered Automatic Voltage Regulation During bro
14. te product No purchase necessary Void where prohibited Some restrictions apply See website for details FCC RADIO TV INTERFERENCE NOTICE FOR CLASS A MODELS Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications Operation of this equipment is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense The user must use shielded cables and connectors with this product Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment FCC RADIO TV INTERFERENCE NOTICE FOR CLASS B MODELS Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual
15. wnouts your UPS will auto matically correct low AC line voltage When automatic voltage regulation is operating your UPS may be heard to click gently This is a normal automatic operation of your UPS and no action is required on your part Storage amp Service Storage All connected equipment should be turned off then disconnected from the UPS to avoid bat tery drain Unplug your UPS from its AC receptacle then press and hold its ON OFF button to deactivate it Your UPS is now ready for storage If you plan on storing your UPS for an extend ed period of time fully recharge the UPS batteries once every three months by plugging the UPS into a live AC outlet and letting the UPS charge for 4 to 6 hours If you leave your UPS bat teries discharged for an extended period of time they will suffer a permanent loss of capacity Service If returning your UPS for service contact your local Tripp Lite dealer or distributor They will refer you to a service center Please carefully pack the UPS using the ORIGINAL PACKING MATERIAL that came with the unit Enclose a letter describing the symptoms of the problem If the UPS is within the warranty period enclose a copy of your sales receipt NORM DELAY Warranty Registration Visit www tripplite com warranty today to register the warranty for your new Tripp Lite prod uct You ll be automatically entered into a drawing for a chance to win a FREE Tripp Li
Download Pdf Manuals
Related Search