CyberPower CP685AVR uninterruptible power supply (UPS)
Contents
1. Slide the battery compartment cover completely off of the unit i Inspect the UPS upon receipt The box should contain the following 6 Remove the battery from the compartment 1 UPS unit 1 User s manual 1 PowerPanel Personal Edition software CD 1 USB device cable 1 Telephone cable 1 Warranty 7 Disconnect the battery wires from the battery registration card 1 Coaxial Cable 8 Install the replacement battery by connecting the red wire and black wire to the positive and negative terminal of the battery 9 Put the battery back into the compartment 10 Slide back the battery compartment cover and tighten the retaining screw WHAT IS AVR What is AVR The CP685AVR BF685 CP800AVR BF800 provide complete power protection from utility power that is not always consistent The CP685AVR BF685 CP800AVR BF800 features 890 Joules of surge protection and provide long lasting battery backup with a 8AH 9AH batteries for loss of utility power and voltage sags The CP685AVR BF685 CP800AVR BF800 ensure consistent power to your computer system and include software that will 11 Recharge the unit for 4 8 hours to fully charge the battery REMINDER Batteries are consider HAZARDOUS WASTE and must be disposed of properly Almost any retailer that sells lead acid batteries collects used batteries for recycling as required by most state laws TROUBLE SHOOTING automatically save your open files and shutdown your co2. volt power lines in the United States and Canada transients surges or spikes on standard telephone land lines PBX telephone equipment lines or Base 10T Ethernet lines when properly installed and connected This exclusion applies for example to fluctuations in data transmission or reception by CATV or RF transmission or fluctuations or by transients in such transmission 3 Damage from any circumstance described as excluded above with respect to the product 4 Damages from fire flood wind rain rising water leakage or breakage of plumbing abuse misuse or alteration of either the product or the Connected Equipment Exclusion of Consequential and Other Damages The sole and exclusive remedies of the Initial Customer are those provided by the Limited Warranty and Connected Equipment Guarantee CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee CyberPower excludes any liability for direct indirect special incidental or consequential damages whether for damage to or loss of property EXCEPT FOR AND ONLY FOR the specific limited agreement of CYBERPOWER to provide certain warranty benefits regarding Connected Equipment under the CYBERPOWER Connected Equipment Guarantee loss of profits business interruption or loss of information or data NOTE Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitation
3. N DESCRIPTION Additional troubleshooting information can be found at www cyberpowersystems com support htm If you are using a serial cable you must use a CyberPower serial cable If you need this cable please contact technical support tech cyberpowersystems com The serial cable is not the cable that was included with the UPS unit Battery and Surge Protected Outlets The unit has ou battery powered surge Pies outlets for TECH NICAL SPECI FICATIONS connected equipments and ensures temporary uninterrupted operation of your equipment during a power failure i CP685AVR BF685 CP800AVR BF800 Full Time Surge Protection Outlets The unit has four always on surge suppression outlets i aay ss 685VA 390W 800VA 450W Power Switch Input Voltage on Utility 90V to 140V Can be used as a master on off switch for equipment Input Frequency 57 Hz to 63 Hz connected to the battery power supplied outlets On Battery Output Voltage 120Vac 5 Power On inaigmar 4ms Typical This LED is illuminated when the utility condition is normal Max Load for UPS Outlets 4 Outlets 685VA 390W 800VA 450W and the UPS outlets are providing power free of surges i ii e p Max Load for Full Time Surge Protection outlets 8 Outlets 12 Amps Electrical Wiring Fault Indicator T ics o E On Battery Output Wave Form Simulated Sine Wave Form This LED indicator will illuminate to warn the user that a wiring problem exists such as bad ground missing g
4. P685AVR BF685 CP800AVR BF800 in the United States or Canada the original end user receives a Limited Warranty and Connected Equipment Guarantee from Cyber Power Systems USA Inc for ease of reading referred to as CyberPower The Limited Warranty and the Connected Equipment Guarantee are intended to be the original end user s exclusive rights and remedies The Limited Warranty and the Connected Equipment are separate all though they are related Limited Warranty The original end user referred to as the Initial Customer receives an express limited warranty referred to as the Limited Warranty for the CP685AVR BF685 CP800AVR BF800 purchased from CyberPower referred to as the Product The Limited Warranty is for the Product itself The terms of the Limited Warranty are explained below Connected Equipment Guarantee CyberPower also provides the Initial Customer with protection in the event that the Product is not free from defects in materials and workmanship and certain equipment connected to the Product is damaged the Connected Equipment Guarantee The Connected Equipment Guarantee protects the Initial Customer for damage to equipment plugged into the Product The terms of the Connected Equipment Guarantee are explained below The Limited Warranty and the Connected Equipment Guarantee are subject to the terms set forth below Additionally State or Provincial law may adjust the terms of the Limited Warranty or the Connected E
5. UPS control provided by Windows 2000 and Windows XP Note Only one of these two ports can be used to communicate with your computer at one time Note To install PowerPanel Personal Edition Software the computer will need Microsoft Internet Explore 5 0 or higher berPower T h B P Ower T 0 C n t ro t h e P Owe le Note If using the Serial Port users need to download Power Panel software from our website http www cyberpowersystems com and order the standard serial cable If you have any questions email CyberPower C P6 8 5 AV R B F6 8 5 technical support for help tech cyberpowersystems com Outlets Designed for AC Adapters C PSOOAV R B F800 The unit has four outlets spaced to allow AC power adapter blocks to be plugged into the UPS without blocking adjacent outlets j Vertical Use Stand User S Man ual The unit can be placed on it s end in a vertical orientation Note We recommend you place the unit next to the wall when standing the unit vertically Coax Cable DSS Surge Protection The Coax Cable DSS surge protection ports will protect any cable modem CATV converter or DSS receiver IMPORTANT SAFETY WARNINGS REPLACING THE BATTERY SAVE THESE INSTRUCTIONS Cy K01 BF80000 This manual contains important safety instructions Please read and follow all instructions carefully during installation and operation of the CAUTION Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery Servi
6. Warranty card or provide reasonable proof of purchase for example a sales receipt that establishes you as the original end user consumer purchaser of the Product 2 Call CyberPower at 952 403 9500 or 877 297 6937 toll free write to CyberPower at 5555 12th Ave East Suite 110 Shakopee MN 55379 or e mail CyberPower at clains cyberpowersystems com within ten 10 days of the date of the event for which you wish to make a claim for warranty service 3 When you contact CyberPower identify the Product the Purchase Date and the item s of Connected Equipment Have information on all applicable insurance or other resources of recovery payment that are available to the Initial Customer and the name of the power utility supplier for the location of the Connected Equipment and Request a Claim Number 4 Pack and ship the product to CyberPower and if requested the item s of Connected Equipment a repair cost estimate for the damage to the Connected Equipment and all claim forms that CyberPower provides to you Show the Claim Number on the shipping label or include it with the product Initial Customer shall prepay all shipping costs must pay the cost of the repair estimate and is responsible for packaging and shipment CyberPower s Duties CyberPower will inspect and examine the Product and the item s of Connected Equipment or at CyberPower s election your written statement and repair cost estimate for those item s You must return the pr
7. ce the battery under the unit Read this manual thoroughly before attempting to unpack install or operate your UPS supervision of personnel knowledgeable of batteries and their precautions CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area free of conductive CAUTION Use only the specified type of battery See your dealer for replacement batteries contaminants Please see specifications for acceptable temperature and humidity range CAUTION CAUTION The battery may present a risk of electrical shock Do not dispose of battery in a fire as it may explode Follow CAUTION To reduce the risk of electric shock do not remove the cover except to service the battery No user serviceable parts inside all local ordinances regarding proper disposal of batteries Almost any retailer that sells lead acid batteries collects used batteries for except for battery recycling as required by most state laws CAUTION Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected CAUTION Do not open or mutilate the batteries Released electrolyte is harmful to skin and eyes and may be toxic CAUTION UPS must be connected to an AC power outlet with fuse or circuit breaker protection Do not plug into an outlet that is not CAUTION A battery can present a high risk of short circuit current and electrical shock Take the following precautions before replacing grounded l
8. ent so that CyberPower s maximum liability shall be reduced to reflect all such other payments or sources of recovery If CyberPower replaces the connected equipment or pays to the Initial Customer the Agreed Damage Amount the Initial Customer shall transfer ownership of all item s to CyberPower without warranty by the Initial Customer but free of lien or other interest CONDITIONS COMMON TO THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE The Limited Warranty and the Connected Equipment Guarantee are the only and the exclusive express warranty of CyberPower with respect to the Product This exclusion of other express warranties applies to written and oral express warranties LIMITATION THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE DOES NOT COVER The Limited Warranty and the Connected Equipment Guarantee are intended to exclusive rights and remedies and replace any other rights to the extent allowed by law 1 As to the CyberPower Product the limited warranty does not cover or apply to misuse modification operation or storage outside environmental limits for the Products in transit in shipment or in storage damage or deterioration improper operation or maintenance or use with items or equipment not designed or intended for use with the product 2 As to Connected Equipment the Connected Equipment Guarantee covers only damage within the specific terms of the Connected Equipment Guarantee to Connected Equipment and
9. f you need to de energize this equipment turn off and unplug the unit the battery CAUTION To avoid electrical shock turn off the unit and unplug it from the AC power source before servicing the battery or installing a 1 Remove all watches rings or other metal objects computer component 2 Only use tools with insulated handles DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT CyberPower Systems does not sell products for life support or medical 3 Do not lay tools or metal parts on top of battery or any terminals applications DO NOT use in any circumstance that would affect operation or safety of any life support equipment or with any medical 4 Wear rubber gloves and boots applications or patient care 5 Determine if the battery is inadvertently grounded If grounded remove the source of ground CONTACT WITH GROUNDED BATTERY DO NOT USE WITH OR NEAR AQUARIUMS To reduce the risk of fire or electric shock do not use with or near an aquarium CAN RESULT IN ELECTRICAL SHOCK Condensation from the aquarium can cause the unit to short out DO NOT USE WITH LASER PRINTERS The power demands of these devices will overload and possibly damage the unit TO REPLACE THE BATTERY 1 Turn off and unplug all connected equipment INSTALLING YOU R UPS SYSTEM 2 Turn the UPS off and unplug it from the AC power source aw gt a i aL CN 3 Turn the UPS upside down ied a 1 a i ag a UNPACKING 4 Remove the 1 retaining screw tig li A Gr a ii F a i i 5
10. g shipping and Thoonien switch iedesignedto F ga storage To recharge the battery simply leave the unit plugged into an AC outlet peee prevent damage by rapidly turning it Turn the UPS off Wait 10 seconds and then turn the UPS on and turn on the power switch vat off and on 2 With the UPS unit off and unplugged connect your computer monitor and any externally powered data storage device Zip drive Jazz drive Tape drive etc into the battery power supplied outlets Plug your The unit is not connected to an AC Th unt must be connacted io a 110 420v GOUz ouilet i outlet peripheral equipment printer scanner speakers into the full time surge protection outlets DO NOT plug a laser printer paper DRE oo G 4 shredder copier space heater vacuum or other large electrical device into the UPS The power demands of these devices Contact CyberPower Systems about replacement batteries at will overload and possibly damage the unit The battery is worn out tech cyberpowersystems com 3 To surge protect a network connection connect a network cable from the wall jack outlet to the IN jack of the ia UPS Then connect a network cable from the OUT jack on the UPS to the network device j ice ee Contact CyberPower Systems at IN OUT Mechanical problem h 4 Plug the UPS into a 2 pole 3 wire grounding receptacle wall outlet Make sure the wall branch outlet is tech cyberpowersystems com protected by a fuse or circuit breake
11. may not apply to you DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES CyberPower does not sell the Products for use in high risk activities The Product is not designed or intended for use in hazardous environments requiring fail safe performance including the operation of nuclear facilities aircraft navigation or communication systems air traffic control weapons systems life support or medical applications or for use in any circumstance in which the failure of the Product could lead directly to death personal injury or severe physical or property damage or that would affect operation or safety of any medical or life support device collectively High Risk Activities CyberPower expressly disclaims any express or implied warranty of fitness for High Risk Activities CyberPower does not authorize use of any of its products use in any High Risk Activities ANY SUCH USE IS IMPROPER AND IS A MISUSE OF CYBERPOWER PRODUCTS The Limited Warranty and the Connected Equipment Guarantee are governed by the laws of the United States and the State of Minnesota without reference to conflict of law principles The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded Contact Information CyberPower s address is 5555 12th Ave East Suite 110 Shakopee MN 55379 and its phone number is 952 403 9500 or Toll free 877 297 6937 CyberPower is the warrantor under thi
12. mputer system during a utility power loss AUTOMATIC VOLTAGE REGULATOR Full time surge protection outlets stop providing power to ere l Turn the UPS off and unplug at least one piece of equipment of PE i l od Circuit breaker has tripped due to an wee The CP685AVR BF685 CP800AVR BF800 stabilize utility power voltage levels that can be inconsistent The incoming utility power may equipment Circuit breaker enad Wait 10 seconds reset the circuit breaker by depressing the be damaging to important data files but with Automatic Voltage Regulation the computer will only not experience damaging voltage levels button is projecting from the side l button and then turn the UPS on An Automatic Voltage Regulator automatically increases low or decreases high voltage to a consistent computer safe 110v 120v The oi ine unik units powerful 8AH 9AH battery will provide power only if the incoming voltage drops below 90v or increases above 140v Battery not fully charged Recharge the battery by leaving the UPS plugged in HARDWARE INSTALLATION GUIDE The UPS does not perform expected runtime 1 Your new UPS may be used immediately upon receipt However recharging the Battery is slightly worn out Dante Cube FONE yms aeubrepiaessient pallies Al tech cyberpowersystems com battery for at least 16 hours is recommended to insure that the battery s maximum PLUG IH h ue Gohi l l ee charge capacity is achieved A loss of charge may occur durin
13. nitor with 15 Monitor CP685AVR f 70 minutes 45 minutes 28 minutes 22 minutes 16 minutes BF685 CP800AVR f 52 minutes 36 minutes 20 minutes BF800 DEFINITIONS FOR ILLUMINATED LED INDICATORS All CONDITION Power ON Wiring Fault Alarm Utility Failure The UPS is providing power to battery power supplied On Off Two Beeps y p gp yp pp outlets from its battery Utility Failure The UPS is providing battery power Rapid beeps On Off Rapid Beeps oo Y o j J ue j i indicate the unit will run out of power shortly Desktop PC Desktop PC with 17 Monitor with 21 Monitor 85 minutes 28 minutes System Overload Occurs when connected equipment exceeds the rating Long Beep of unit Turn the UPS off unplug at least one piece of equipment wait 10 seconds reset the circuit breaker and turn the unit on Battery Overload Occurs when connected equipment exceeds the rating of battery outlets of the unit Turn the UPS off unplug at least one piece On Off Long Beep l ae of equipment from battery outlets wait 10 seconds reset the circuit breaker and turn the unit on Electrical Wiring Fault This indicates a wiring problem with the AC On Off outlet such as bad ground missing ground or reversed wiring User is advised to disconnect all electrical equipment from the outlet and have an electrician check the outlet to insure proper wiring Limited Warranty and Connected Equipment Guarantee In purchasing a C
14. oduct for inspection If the damage to Connected Equipment is covered by the Connected Equipment Guarantee CyberPower will in addition to Limited Warranty remedies for the CyberPower Product itself repair or pay the costs of repair or replace the Connected Equipment or at the option of CyberPower as permitted by law pay to the Initial Customer the Agreed Damage Amount up to the aggregate limits stated below for all item s of Initial Customer s Connected Equipment The Agreed Damage Amount for all items of Initial Customer s Connected Equipment shall be the lesser of the amount determined under Clause 1 or 2 below reduced by any amounts described in Clause 3 below 1 The fair market value of the Connected Equipment as established by the lower of a the price list of Orion Blue Book on the date of occurrence or if such price list is no longer published a published or announced price list reasonably selected by CyberPower or b the average price the same or similar items are being sold for on E bay or c the lowest price the same or similar items can be purchased for in the United States or 2 The aggregate ceiling amount for all Connected Equipment CyberPower CP685AVR BF685 125 000 00 CP800AVR BF800 200 000 00 3 The amount s of all payment you have or are entitled to receive from insurance other warranties extended warranties or from other sources or persons for the Connected Equipment or damage to such equipm
15. only up to the applicable aggregate ceiling amount 3 The Connected Equipment Guarantee does not cover damage to Connected Equipment or apply if the Product has been operated in a failure mode or not in compliance with CyberPower operating instructions and manuals or if the Connected Equipment has been operated in a failure mode or not in compliance with the instructions and manuals of its manufacturer vendor The Limited Warranty and the Connected Equipment Guarantee Do Not Apply Unless The Initial Customer 1 Has properly connected the Product and the Connected Equipment to properly wired and grounded outlets including compliance with electrical and safety codes of the most current electrical code ANS NFPA 70 without the use of any adapters extension cords or other connectors 2 Has provided a suitable and proper environment for use and installation of the Product and Connected Equipment 3 Has properly installed and operated the CyberPower Product and Connected equipment 4 Has operated the Product at all times within the limitations on the Product s VA capacity as stated in this User Manual CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following 1 Loss of or damage to data records or software or the restoration of data or records or the reinstallation of software 2 Damage from causes other than AC Power Line Transients spikes or surges on properly installed grounded and code compliant 120
16. quipment Guarantee or the State or Province may impose additional obligations or additional implied warranties To the extent necessary to comply with those laws the terms of the Limited Warranty and the Connected Equipment Guarantee should be read to adjust to those requirements only to the extent necessary to comply with such local law If you are an Initial Customer you are asked to read the following terms and conditions carefully before using the Product By using the Product you consent to be bound by and become a party to the Limited Warranty and Connected Equipment Guarantee If you do not agree to the terms and conditions of the Limited Warranty and Connected Equipment Guarantee you should return the Product for a full refund prior to using it REGISTRATION CyberPower requests that you complete and return the Warranty Registration Card enclosed with the Product or register the Product at its website www cyberpowersystems com to establish that you are the Initial Customer of the Product and therefore entitled coverage under the Limited Warranty and the Connected Equipment Guarantee Registration is not required for Limited Warranty coverage but note if you do not complete a registration card you will be required to provide proof of purchase as described below to have the benefits of this Limited Warranty LIMITED WARRANTY CyberPower warrants to you the Initial Purchaser that the Product will be free from defects in material and wo
17. r and does not service equipment with large electrical demands e g refrigerator copier etc The USB serial cable is not Connect the USB serial cable to the UPS unit and an open USB serial port on the back of the computer You must use connected the cable that came with the unit The warranty prohibits the use of extension cords outlet strips and surge strips 5 Press the power switch to turn the unit on The power on indicator light will illuminate and the unit will beep once 6 If an overload is detected an audible alarm will sound and the unit will emit one long beep To correct this turn the UPS off and unplug The USB7 senalcable is connected Check the back of the computer for an additional USB serial at least one piece of equipment from the battery power supplied outlets Wait 10 seconds Make sure the circuit breaker is depressed to the wrong port port Move the cable to this port and then turn the UPS on PowerPanel Personal Edition is inactive all icons are gray 7 To maintain optimal battery charge leave the UPS plugged into an AC outlet at all times The unit is not providing battery Shutdown your computer and turn the UPS off Wait 10 8 To store your UPS for an extended period cover it and store with the battery fully charged While in storage recharge the battery every power seconds and turn the UPS back on This should reset the unit three months to insure battery life BASIC OPERATIO
18. rkmanship for three years from the date of original purchase subject to the terms of this Limited Warranty Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose if applicable to the Product is limited in duration to the period of ownership by the Initial Customer This provision shall NOT create any Implied Warranty or Merchantability or of Fitness for a Particular Purpose that would not otherwise apply to the Product NOTE Some States do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty Exclusive Remedies Under Limited Warranty Your exclusive remedy and CyberPower s sole obligations are as follows for the Product If a the CyberPower Product you purchased and still own is defective in material or workmanship under this Limited Warranty or any applicable warranty imposed by law and b all Limited Warranty requirements have been met CyberPower will repair or replace the Product if it proves to be defective in material or workmanship during the Warranty Period Making a Limited Warranty Claim To make a Limited Warranty claim on a Product you must do the following 1 Complete and return the CyberPower Warranty Registration Card or provide reasonable proof of purchase for example a sales receipt that establishe
19. round or reversed wiring oe f ae Operating Temperature 32 F to 95 F 0 C to 35 C If this is illuminated user is advised to disconnect all electrical equipment from the outlet and have an electrician check to ensure the outlet is properly wired The unit will not provide surge protection without being plugged into a grounded and properly wired wall outlet Ccinmunication Protection Ports Size L x W x H 11 x 6 5 8 x 3 1 2 28cm x 16 9cm x 8 7cm Communication protection ports will protect any standard modem fax telephone line broadband network or Ethernet connection Net Weight 13 7 Ibs 14 3 Ibs Circuit Breaker Typical Battery Recharge Time 8 hours typical from total discharge Located on the side of the UPS the circuit breaker serves to provide overload and fault protection Typical Battery Life 3 to 6 years depending on number of discharge recharge cycles Serial USB Ports to PC Battery Type 12V 8 0AH 12V 9 0AH The ports allow connection and communication from the USB or DB 9 serial port on the computer to the UPS unit The UPS Recommended Battery Spill proof Maintenance free sealed lead acid communicates its status to the PowerPanel Personal Edition software This interface is also compatible with Power Management Safety Approvals UL1778 UPS cUL107 FCC DoC Class B EXPECTED RUNTIME IN MINUTES Due to the differences in computer components the runtime will vary Desktop PC Desktop PC with iMac G4 LCD Mo
20. s Limited Warranty You may also contact CyberPower on the Internet at www cyberpowersystems com Wallmount 150 00
21. s you as the Initial Customer the original end user consumer purchaser of the Product and prove that the Product was purchased within three 3 years of the event for which you want to make a claim for warranty service 2 Call CyberPower at 952 403 9500 or 877 297 6937 toll free write to CyberPower at 5555 12th Ave East Suite 110 Shakopee MN 55379 or e mail CyberPower at claims cyberpowersystems com within ten 10 days of the event for which you want to make a claim 3 When you contact CyberPower identify the Product the Purchase Date and request Return Materials Authorization RMA information from CyberPower 4 Pack and ship the Product to CyberPower as instructed in your RMA Show the RMA code on the shipping label or include it with the Product You MUST prepay all shipping costs and you are responsible for packaging and shipment CyberPower will inspect and examine the Product within ten 10 days of receipt If the Product is not as warranted CyberPower will repair or replace the Product and return it to you at CyberPower s expense or if CyberPower is unable to or decides not to repair or replace the Product if defective within a reasonable time CyberPower will refund to you the full purchase price you paid for the Product purchase receipt showing price paid is required CONNECTED EQUIPMENT GUARANTEE If you are the Initial Purchaser and the Product is still covered by the Limited Warranty the Connected Equipment Guarantee pro
22. tions or exclusions on warranty coverage apply or than the three year limit CyberPower will as CyberPower elects as permitted by law repair replace or pay the Agreed Damage Amount defined below for the item s of your electronic equipment directly and properly connected to the product the Connected Equipment if that Connected Equipment is x damaged by AC power line transients spikes or surges on properly installed grounded and code compliant 120 volt power lines in the United States and Canada or by transients surges or spikes on standard telephone equipment lines or Base 10 100T Ethernet lines that are properly installed and connected a Power Disturbance and y is directly plugged into and properly connected to a CyberPower Product in its original condition which is properly operated when a Power Disturbance passes through the CyberPower Product and y 1 exhausts the protection capacity of the CyberPower Product or y 2 damages the CyberPower Product This provision sets out the only liability of any character of CyberPower for direct indirect special consequential and or incidental damages under our Limited Warranty applies only to Connected Equipment and all such Liability is limited to the Agreed Damage Amount Making a Connected Equipment Guarantee Claim To make a Warranty claim for damage to Connected Equipment under the Connected Equipment Guarantee you must do the following 1 Complete and return the CyberPower
23. vides protection for damage to equipment connected to the Product Connected Equipment subject to certain terms and limitations The Connected Equipment Guarantee is not first dollar coverage It is secondary If you have any other source of payment for your loss such as insurance another warranty or an extended warranty or purchase protection plan Primary Coverage CyberPower will pay only to the extent that that the Primary Coverage does not cover the loss CyberPower s obligation is reduced by any amounts that you are entitled to recover from the Primary Coverage whether or not you make a claim for recovery under any applicable Primary Coverage The Limited Warranty does not cover Connected Equipment but as is explained below to be covered under the Connected Equipment Guarantee the Connected Equipment must have been damaged due to a failure of the Product The Connected Equipment must have been damaged due to a defect in materials or workmanship of the Product In the event of damage to the Connected Equipment your exclusive remedies and CyberPower s sole obligations are as follows for Connected Equipment If a the Product purchased and owned by you is defective in material or workmanship b the Limited Warranty requirements have been met except that the three year limitation of the Limited Warranty does not limit the Connected Equipment Guarantee which is for the lifetime of the Product and c none of the limita
Download Pdf Manuals
Related Search