Edge10 C172 LCD Monitor
Contents
1. covers may expose you to dangerous voltage points or other risks e Do not touch the screen directly with your fingers You may damage the screen and the grease from your skin is difficult to remove e Do not apply pressure to screen The LCD is very delicate Power Use the type of power indicated on the rating label Plug Do not remove any of the prongs of the monitor s three pronged power plug Disconnect the power plug from the AC outlet under following conditions e If you are not using it for an indefinite period time e When the power cord or plug is damaged or frayed o If the product does not operate normally when the operating instructions are followed If the product has been dropped or the cabinet has been damaged o If the product exhibits a distinct change in performance indicating need for service Power and extension cord Do not allow anything to rest on the power cord e Do not locate this product where persons will walk on the cord Use the proper power cord with correct attachment plug type If the power source is 120V AC use a power cord that has UL and C UL approvals If the power source 1s a 240V AC supply use the tandem T blade type attachment plug with ground conductor power cord that meets the respective European country s safety regulations such as VDE for Germany e Do not overload wall outlets or power cords Ensure that the total of all units plugged into the wall outlet does not e2. CEES COLOUR TFT LCD MONITOR USER S MANUAL Model C172 The display comes with a three year on site warranty To activate your warranty please register your display at http www edgel0 com by clicking on the help amp support link Menu Introduction Product Description rrrnrnnnnnnrrrrnrnnnnnnnrrrrrnnnnnnnnrrrnrnnnnnnnennrnnnnnnnnnneeee Page 2 DEG ee SOOM SIS EE Page 2 Product ECE CS EE Page 2 Go EEE Page 2 PECAN ENE NE Page 2 2 Control Function ODE EEE EEE Page 4 SDI Go EEE NE Page 5 See 0 EEE Page 5 3 Inputs Diagram Hu 44424744 Page 10 4 DS 0 ae Ce eee eee Page 10 hr EEE Page 10 5 Product Specification rornronrrrnnnnorrrrnnornrnnnrrnnnnnrrnnnnerrvnnennnnene Page I I 6 Display Modes rrrrnrornronnornrnnnrrnnnnnrnvnnnnrnvnnnnrnnnnernnnnnsrnnnnssnnnnnere Page 12 7 Service MIO FAG OO avvek Page 12 Introduction Product Description Congratulations on your purchasing this new generation of monitor Your LCD monitor incorporates high quality display into a small light weighted module It has power saving capabilities and emits no X ray radiation You will certainly benefit from this monitor in lots of way to name some of them comfort safety and environmental protection This LCD monitor incorporates 17 colour active matrix thin film transistor TFT liquid crystal display to provide superior display performance A maximum resolution of SXGA 1280X1024 is ideal for designs tha
3. d press MENU or A button to adjust the setting values Press and to choice the Turn off mode hour and minute and press e e MENU or A button to adjust the setting values Press and to choice the Turn on mode hour and minute and press MENU or A button to adjust the setting values Press and to adjust the default program program Press and to choice the Switch hour and minute And press MENU or A button to adjust the setting values Switch Press and to choice the different programs program OSD EOSIION n Pr FOYE Function Description Language Press and to choice the language Chinese English Italian Spanish Portuguese German France Press and to move the OSD MENU position to right or left Press and to move the OSD MENU position to up or down Duration Press and to set the OSD off time Press and to adjust the transparency of the OSD menu Bec Aa amp amp e gt a a CONTRAST BRIGHTNESS SATURATION HOVE SHARPNESS SATURATION C I TE COLOR TONE NORMAL b NODER USER gt SELECT G Function Description gt Contrast Press and to adjust the setting value 0 100 to adjust the contrast Brightness Press and to adjust the setting value 0 100 to adjust the bri
4. ghtness UE Not available for this mode Saturation press and to adjust Sharpness press and to adjust Colour Tome Press and to adjust the colour NORMAL WARM COOL Picture Mode Press and to choose the Mode DEFAULT BRIGHT SOFT NATURE Inputs Diagram Inputs AC POWER INPUT AC inlet for 100 240V power system PC INPUT This D sub 15 sockets can be connected to a PC S VIDEO INPUT Inputs S video signal by DIN socket VIDEO IN This BNC socket can be connected to composite video output al Display Angle Tilting For viewing clarity you can tilt the LCD forward Down to 5 degrees or backward Up to 18 degrees Down 5 ZA Product Specification ee ee LCD Display 17 active matrix TFT LCD panel Viewing Angle L R 75 9 75 PC Interface Video RGB analog 0 7Vp p Sync Display Mode VGA SVGA XGA SXGA Front Control Power on off with LED Menu select Up Down Adjustment Source OSD Adjustment Contrast Brightness Auto tuning Phase Clock Position Input selection AC Input 100 240V 1 2A 50 60Hz Operating 42W Consumption Operating Conditions Temperature 0 C 40 C Humidity 20 80 Storage Conditions Temperature 10 C 60 CHumidity 20 80 N W 3 6Kgs GIW 4 7Kgs Display Model Horizontal Vertical Operating Display Mode Frequency Frequency Mode KHz Hz Analog 800 x 600 Service Information Service When you buy this e
5. t enhance this LCD monitor s performance are Plug amp play compatibility audio system and OSD On Screen Display controls Package Contents Included with your LCD monitor are following e 17 TFT LCD monitor 15pin D sub signal cable e AC power cable e User s manual e Warranty Card Product Features e High contrast colour TFT LCD display support resolution up to SXGA 1280X1024 e Compatible with IBM VGA VESA and Macintosh standards e Embedded audio system provides sound performance Video in and S video use Cleaning Gently wipe the screen with a clean camel hair lens brush or a soft clean lint free cloth e This removes dust and other particles that can scratch the screen e Do not apply pressure to the screen surface when wiping it clean e Do not pour or spray any liquid directly onto the screen or case of the LCD monitor Chemical cleaners have been reported to damage the screen or the LCD monitor Precautions Read all these instructions and save them for later use e Follow all warning and instructions on the product Product Do not block the vent holes in the case Do not insert sharp objects or spill liquid into the LCD monitor through cabinet slots It may cause accidental fire electric shock or failure Disconnect the power plug from the AC outlet if you are not using it for an indefinite period of time Do not attempt to service this product yourself as opening or removing
6. to enter OSD menu 2 Press SOURCE to Exit OSD menu on screen Display or Exit adjustment item 3 Press and to selects main menu item left right 4 Press MENU to confirm and enter to the sub menu 5 Press MENU and A to selects the sub menu items Up down 6 Press and to adjust the setting values then press up or down to select next item PC MODE oe MOVE Auto ADJUST HOV SELECT X press and to adjust the setting value 0 100 to adjust contrast Brightness press and to adjust the setting value 0 100 to adjust brightness Press and to move OSD MENU position to right or left Press and to move OSD MENU position to up or down Press and to adjust the distortion character 5 Press and to adjust the real image value of ADC Colour Press and to adjust the colour mode NORMAL WARM COOL USER Auto Adjust press and to Auto tuning TIMER FUNCTION a Timer Press and to adjust sub items Current Turn off Turn on Turn on program Switch and Switch program PIC Misc Not available for this model Not available for this model i r Y l n A A d i r p A i gt Deere r gt rzr gt ey r ae ere Sr rr ________ e Description Current Press and to choice the Current mode hour and minute an
7. xceed 10 amperes Ensure that the total ampere ratings on all units plugged into the extension cord is not above the cord s rating e Ifthe power supply cord which came with your monitor is to be connected to the PC instead of the wall outlet this equipment is to be used with UL TUV approved computers with receptacle rated 100 240V AC 50 60Hz 1 0A minimum Environment Place the monitor on a flat and level surface e Place the monitor in a well ventilated place Keep the monitor away from Overly hot cold or humid places places directly under sunlight dusty surroundings equipment that generates strong magnetic field Control Function Control Button Front View GC Power LED Indicates different status Green Normal operation Red Power Management Dark Power turn off 2 Power switch Turns power on off 3 Button Adjust setting bars i e Contrast Brightness etc to increase setting values of the OSD 4 Button Adjust setting bars i e Contrast Brightness etc to Decrease setting values of the OSD A Button Press to bring up the selection on OSD and select sub menu items 6 MENU Button Enter the OSD on Screen Display and still can select sub menu items SOURCE Button Selects input mode PC gt VIDEO gt SVIDEO gt PC Exit the OSD On screen Display or exit the selected item OSD Control Operating Procedure 1 Press MENU
8. xcellent LCD Monitor you are entitled to the warranty provided by us please contact us 1f you need any information on our product Thank you again for buying our product www edgel0 com
Download Pdf Manuals
Related Search