Indesit IWDE7145 washer dryer
Contents
1. 12 Synthetics e 3 13 Express Wash amp Dry 30 1400 e 0 5 H Partial wash cycles g A Rinse 1400 7 Spin 1400 7 Drain O T For all Test Institutes The information contained in the table is intended as a guide only 1 Test wash cycle in compliance with regulation EN 50229 set wash cycle 1 with a temperature of 60 C 2 Long wash cycle for cottons set wash cycle 1 with a temperature of 40 C 3 Short wash cycle for cottons set wash cycle 3 with a temperature of 40 C Wash options Eco Time Selecting this option enables you to suitably adjust drum rotation temperature and water to a reduced load of lightly soiled cotton and synthetic fabrics refer to the Table of wash cycles EcoTime enables you to wash in less time thereby saving water and electricity We suggest using a liquid detergent suitably measured out to the load quantity l This function may not be used in conjunction with NNN wash cycles 1 5 6 7 8 9 10 11 12 13 9 S Intensive Wash Because a greater quantity of water is used in the initial phase of the cycle and because of the increased cycle duration this function offers a high performance wash l This function may not be used in conjunction with wash cycles 5 6 7 8 9 10 11 12 13 9 X Easy iron By selecting this function the wash and spin cycles will be modified in order to reduce the2. Display The display is useful when programming the machine and provides a great deal of information The duration of the available programmes and the remaining time of a running cycle appear in section A if the DELAY START option has been set the countdown to the start of the selected programme will appear Furthermore pressing the corresponding button allows you to view the maximum temperature spin speed and drying level or time values attained by the machine during the selected cycle The phases scheduled for the selected cycle and once the cycle has begun the current phase of the wash cycle and drying cycle if applicable appear in section B amp Wash 29 Rinse Spin Drain Drying The icons corresponding to temperature O Drying zO and spin appear in section C from top to bottom If the O symbol lights up the display will visualise the set temperature value The 0 symbol lights up while the drying settings are being adjusted If the symbol lights up the display will visualise the set spin value Door locked symbol 3 The lit symbol indicates that the door is locked To prevent any damage wait until the symbol turns off before opening the door To open the door while a cycle is in progress press the START PAUSE button if the DOOR LOCKED amp symbol is switched off the door may be opened How to run a wash cycle ora drying cycle 1 SWITCH THE MACHINE ON Press the button
3. encourage improved load distribution and balance we recommend small and large garments are mixed in the load Precautions and tips CID inpesit This Washer dryer was designed and constructed in accordance with international safety regulations The following information is provided for safety reasons and must therefore be read carefully General safety e This appliance was designed for domestic use only e The Washer dryer must only be used by adults in accordance with the instructions provided in this manual Do not touch the machine when barefoot or with wet or damp hands or feet Do not pull on the power supply cable when unplugging the appliance from the electricity socket Hold the plug and pull Do not open the detergent dispenser drawer while the machine is in operation Do not touch the drained water as it may reach extremely high temperatures Never force the porthole door This could damage the safety lock mechanism designed to prevent accidental opening If the appliance breaks down do not under any circumstances access the internal mechanisms in an attempt to repair it yourself Always keep children well away from the appliance while it is operating The door can become quite hot during the wash cycle If the appliance has to be moved work in a group of two or three people and handle it with the utmost care Never try to do this alone because the appliance is very heavy Before loading la
4. formation of creases At the end of the cycle the Washer dryer will perform slow rotations of the drum the indicator lights for the EASY IRON and START PAUSE options will flash the first one green the second orange To end the cycle press the START PAUSE button or the EASY IRON button For the 6 wash cycle the machine will end the cycle while the laundry is soaking and the EASY IRON and START PAUSE indicator lights will flash To drain the water so that the laundry may be removed press the START PAUSE button or the EASY IRON button This function may not be used in conjunction with wash cycles 5 8 9 10 11 12 13 amp Delay start To set a delayed start for the selected cycle press the corresponding button repeatedly until the required delay period has been reached When this option is enabled the corresponding indicator light will remain lit To remove the delayed start setting press the button until the text OFF appears on the display This option can be used in conjunction with all cycles Detergents and laundry Detergent dispenser drawer Good washing results also depend on the correct dose of detergent adding too much detergent will not necessarily result in a more efficient wash and may in fact cause build up on the inside of your appliance and contribute to environmental pollution l Do not use hand washing detergents because these create too much foam Open the detergent di
5. from its packaging 2 Make sure that the Washer dryer has not been damaged during the transportation process If it has been damaged contact the retailer and do not proceed any further with the installation process 3 Remove the 4 protective screws used during transportation and the rubber washer with the corresponding spacer located on the rear part of the appliance see figure 4 Close off the holes using the plastic plugs provided 5 Keep all the parts in a safe place you will need them again if the Washer dryer needs to be moved to another location Packaging materials should not be used as toys for children Levelling 1 Install the Washer dryer on a flat sturdy floor without resting it up against walls furniture cabinets or anything else 2 If the floor is not perfectly level compen sate for any unevenness by tightening or loosening the adjustable front feet see figure the angle of inclination measured in relation to the worktop must not exceed 2 Levelling the machine correctly will provide it with stability helo to avoid vibrations and excessive noise and prevent it from shifting while it is operating If it is placed on carpet or a rug adjust the feet in such a way as to allow a sufficient ventilation space underneath the Washer dryer Connecting the electricity and water supplies Connecting the water inlet hose 1 Connect the supply pipe by screwing it to a cold water ta
6. option the indicator light corresponding to the button will switch on e Press the button again to disable the option the indicator light will switch off if the selected option is not compatible with the programmed wash cycle the indicator light will flash and the option will not be activated if the selected option is not compatible with another option which has been selected previously the indicator light corresponding to the first option selected will flash and only the second option will be activated the indicator light corresponding to the enabled option will remain lit T The options may affect the recommended load value and or the duration of the cycle 7 START THE PROGRAMME Press the START PAUSE button The corresponding indicator light will become green remaining lit in a fixed manner and the door will be locked the DOOR LOCKED symbol will be on To change a wash cycle while it is in progress pause the Washer dryer using the START PAUSE button the START PAUSE indicator light will flash slowly in an orange colour then select the desired cycle and press the START PAUSE button again To open the door while a cycle is in progress press the START PAUSE button if the DOOR LOCKED amp symbol is switched off the door may be opened Press the START PAUSE button again to restart the wash cycle from the point at which it was interrupted 8 THE END OF THE WASH CYCLE This will be indicated by the text End
7. than 15cms 6 inches If the hose is pushed down appliance too far this may cause the machine to self syphon ie continuously empty as it is filling Disposing of the plug Ensure that before disposing of the plug itself you make the pins unusable so that it cannot be Before plugging the appliance into the mains accidentally inserted into a socket socket make sure that Electric connection Instructions for connecting cable to an alternative plug e the socket is earthed and in compliance with the Important the wires in the mains lead are coloured in applicable law accordance with the following code Green amp Yellow Earth e the socket is able to sustain the appliance s Blue Neutral maximum power load indicated in the Technical Brown Live details table see page 5 As the colours of the wires in the lead may not correspond with the coloured markings identifyng the terminals in your plug proceed as follows Connect Green amp Yellow wire to terminal marked E or or coloured Green or Green amp Yellow Connect Brown wire to terminal marked L or coloured Red Connect Blue wire to terminal marked N or coloured Black Ifa 13 amp plug BS 1368 is used it must be fitted with a 13 amp fuse either in the plug or adaptor or at the distribution board If you are in any doubt the electrical supply to your machine consult a qualified electrician before use How to connect an alternative plug The wires in this mains
8. the START PAUSE indicator light will flash slowly in a green colour 2 LOAD THE LAUNDRY Open the porthole door Load the laundry making sure you do not exceed the maximum load value indicated in the table of programmes on the following page 3 MEASURE OUT THE DETERGENT Pull out the detergent dispenser drawer and pour the detergent into the relevant compartments as described in Detergents and laundry 4 CLOSE THE DOOR 5 SELECT THE WASH CYCLE Set the WASH CYCLE knob to the desired programme a temperature and spin speed is set for each wash cycle these may be adjusted The duration of the cycle will appear on the display 6 CUSTOMISE THE WASH CYCLE Use the relevant buttons he Modifying the temperature and or spin speed he machine automatically displays the maximum temperature and spin speed values set for the selected cycle or the most recently used settings if they are compatible with the selected cycle The temperature can be decreased by pressing the he button until the cold wash OFF setting is reached The spin speed may be progressively reduced by pressing the button until it is completely excluded the OFF setting If these buttons are pressed again the maximum values are restored zO Setting the drying cycle The first time the button is pressed the machine will automatically select the maximum drying cycle which is compatible with the selected wash cycle Subsequent presses will decrease t
9. to call 15 195074263 00 10 2008 Xerox Business Services After Sales Service No one Is better placed to care for your Indesit appliance during the course of its working life than us the manufacturer Essential Contact Information Indesit Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1100 fully qualified engineers on call to ensure you receive fast reliable local service UK 08709 066 066 Republic of Ireland 0818 313 413 www indesitservice co uk Please note Our advisors will require the following information Parts and Accessories We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life UK 08709 077 077 Republic of Ireland 0818 313 413 www indesitservice co uk Indesit Company UK Ltd Morley Way Peterborough PE2 9JB Indesit Company Unit 49 Airways Industrial Estate Dublin 17 LP D Recycling amp Disposal Information As part of Indesit s continued commitment to helping the environment Indesit reserves the right to use quality recycled components to keep down customer costs and minimise material wastage Please dispose of packaging and old appliances carefully To minimise the risk of injury to children remove the door plug and cut the mains cable off flush with the appliance Dispose of the
10. which does not require any maintenance Sometimes small items Such as coins or buttons may fall into the ore chamber which protects the pump situated in its bottom part Make sure the wash cycle has finished and unplug the appliance To access the pre chamber 1 using a screwdriver remove the cover panel on the lower front part of the Washer dryer see figure 2 unscrew the lid by rotating it anti clockwise see figure a little water may trickle out This is perfectly normal 3 clean the inside thoroughly 4 screw the lid back on 5 reposition the panel making sure the hooks are securely in place before you push it onto the appliance Checking the water inlet hose Check the inlet hose at least once a year If there are any cracks it should be replaced immediately during the wash cycles water pressure is very strong and a cracked hose could easily split open T Never use second hand hoses Troubleshooting CD inbesit Your Washer dryer could fail to work Before contacting the Technical Assistance Centre see Assistance make sure that the problem cannot be not solved easily using the following list Problem The Washer dryer does not switch on The wash cycle does not start The Washer dryer does not take in water H20 will flash on the display The Washer dryer continuously takes in and drains water The Washer dryer does not drain or spin The Washer dryer v
11. Assistance e Check whether you can solve the problem alone see Jroubleshooting e Restart the programme to check whether the problem has been solved e f this is not the case contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate Always request the assistance of authorised technicians Have the following information to hand e the type of problem e the appliance model Mod e the serial number S N This information can be found on the data plate applied to the rear of the Washer dryer and can also be found on the front of the appliance by opening the door 14 Guarantee CD inbesit 12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer s guarantee which covers the cost of breakdown repairs for twelve months from the date of purchase This gives you the reassurance that if within that time your appliance is proven to be defective because of either workmanship or materials we will at our discretion either repair or replace the appliance at no cost to you This guarantee is subject to the following conditions The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions The appliance is used only on the electricity or gas supply printed on the rating plate The appliance has been used for normal domestic purposes only The applia
12. ED OUT BY A QUALIFIED ELECTRICIAN connecting the drain hose from the machine Replacing the fuse ensure that any blanks When replacing a faulty fuse a 13 amp ASTA ET ERES or removable ends approved fuse to BS 1362 should always be used ee have been taken off and the fuse cover re fitted If the fuse cover is lost A the spigot the plug must not be used until a replacement is obtained Replacement fuse covers If it is place over the If a replacement fuse cover is fitted it must be of the edge of a basin or sink correct colour as indicated by the coloured marking be sure the free end of or the colour that is embossed in words on the base the hose should not be of the plug Replacements can be obtained directly underwater from your nearest Service Depot Removing the plug If your appliance has a non rewireable moulded plug and you should wish to re route the mains cable through partitions units etc please ensure that either We advise against the use of hose extensions in the plug is replaced by a fused 13 ampere re case of absolute need the extension must have the wearable plug bearing the BSI mark of approval same diameter as the original hose and must not or exceed 150 cm in length the mains cable is wired directly into a 13 amp cable Ensure that if the drain hose is pushed into a outlet controlled by a switch in compliance with BS standpipe that the end does not go down more 5733 which is accessible without moving the
13. Instructions for use WASHER DRYER Contents Installation 2 3 4 5 cB Unpacking and levelling Connecting the electricity and water supplies English 1 The first wash cycle Technical data Description of the Washer dryer 6 7 Control panel Display How to run a wash cycle or a drying cycle 8 Wash cycles and options 9 Table of wash cycles Wash options Detergents and laundry 10 IWDE 7145 Detergent dispenser drawer Preparing the laundry Special wash cycles Load balancing system Precautions and tips 11 General safety Disposal Opening the porthole door manually Care and maintenance 12 Cutting off the water or electricity supply Cleaning the Washer dryer Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Troubleshooting 13 Service and Guarantee 14 15 16 Before calling for Assistance Guarantee 1 inbesit Installation This instruction manual should be kept in a safe place for future reference If the Washer dryer is sold transferred or moved make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself herself with its operation and features Read these instructions carefully they contain vital information relating to the safe installation and operation of the appliance Unpacking and levelling Unpacking 1 Remove the Washer dryer
14. b using a gas threaded connection see figure Before performing the connection allow the water to run freely until it is perfectly clear 2 Connect the inlet hose to the Washer dryer by screwing it onto the corresponding water inlet of the appliance which is situated on the top right hand side of the rear part of the appliance see figure 3 Make sure that the hose is not folded over or bent The water pressure at the tao must fall within the values indicated in the Technical details table see next page if the inlet hose is not long enough contact a specialised shop or an authorised technician T Never use second hand hoses Use the ones supplied with the machine CI inbesit Connecting the drain hose e the supply voltage is included within the values ndicated on the Technical details table Connect the drain hose see page 5 without bending it to a _ draining duct or a wall e the socket is compatible with the washing drain situated between machine s plug If this is not the case replace 65 and 100 cm from the socket or the plug 65 100 cm the floor Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use Before using the appliance please E read the instructions below The drain hose may be WARNING THIS APPLIANCE MUST BE EARTHED connected to an THE FOLLOWING OPERATIONS SHOULD BE under sink trap Before CARRI
15. fixed to the machine minimum pressure 0 05 MPa 0 5 bar drum capacity 52 litres Spin speed up to 1400 rotations per minute Energy rated programmes according to regulation EN 50229 Wash programme 2 temperature 60 C using a load of 7 kg Drying first drying cycle performed with a 2 kg load selecting drying level A1 IRON DRY second drying cycle performed with a 5 kg load selecting drying level A4 EXTRA DRY This appliance conforms to the following EC Directives 89 336 EEC dated 03 05 89 Electromagnetic Compatibility and subsequent modifications 2002 96 EC 2006 95 EC Low Voltage CD inbesit Description of the Washer dryer aB Control panel ON OFF TEMPERATURE OPTION button Button buttons with START PAUSE indicator lights button with indicator light ZAN in OOOO DISPLAY _ Detergent dispenser drawer DRYING SPIN SPEED Button WASH CYCLE Button knob Detergent dispenser drawer used to dispense DRYING button gt lt press to decrease or exclude detergents and washing additives see Detergents drying the esiecied drying level or time will appear on and laundry the display see How to run a wash cycle or a drying cycle ON OFF button press this briefly to switch the machine on or off The START PAUSE indicator light START PAUSE button gt with indicator light when which flashes slowly in a green colour shows tha
16. he drying level and then the drying time until the cycle is excluded completely OFF Drying may be set as follows A Based on the desired laundry dryness level Iron dry suitable for clothes which will need ironing afterwards the remaining dampness softens creases making them easier to remove A1 appears on the display Hanger dry ideal for clothes which do not need to be dried fully A2 appears on the display Cupboard dry suitable for laundry which can be put back in a cupboard without being ironed A3 appears on the display Extra dry suitable for garments which need to be dried completely such as sponges and bathrobes A4 appears on the display B Based on a set time period between 30 and 180 minutes If your laundry load to be washed and dried is much greater than the maximum stated load see adjacent table perform the wash cycle and when the cycle is complete divide the garments into groups and put some of them back in the drum At this point follow the instructions provided for a Drying only cycle Repeat this procedure for the remainder of the load N B a cooling down period is always added to the end of each drying cycle Drying only Use the cycle selector knob to select a drying cycle 11 12 13 in accordance with the type of fabric The desired drying level or time may also be set using the DRYING button 30x Eco Time gt Modifying the cycle settings e Press the button to enable the
17. ibrates a lot during the spin cycle The Washer dryer leaks The option indicator lights and the start pause indicator light flash and an error code appears on the display e g F 01 F There is too much foam The washer dryer does not dry Possible causes Solutions e The appliance is not plugged into the socket fully or is not making contact e There is no power in the house e The Washer dryer door is not closed properly e The ON OFF button has not been pressed e The START PAUSE button has not been pressed e The water tap has not been opened e A delayed start has been set e The water inlet hose is not connected to the tap e The hose is bent e The water tap has not been opened e There is no water supply in the house e The pressure is too low e The START PAUSE button has not been pressed e The drain hose is not fitted at a height between 65 and 100 cm from the floor see nstallation e The free end of the hose is under water see nstallation e The wall drainage system is not fitted with a breather pipe If the problem persists even after these checks turn off the water tap switch the appliance off and contact the Assistance Service If the dwelling is on one of the upper floors of a building there may be problems relating to water drainage causing the Washer dryer to fill with water and drain continuously Special anti draining valves are available in shops and he
18. lead are coloured in accordance with the following code BLUE NEUTRAL N BROWN LIVE L GREEN amp YELLOW EARTH E Disposing of the appliance When disposing of the appliance please remove the plug by cutting the mains cable as close as possible to the plug body and dispose of it as described above GREEN amp YELLOW M BLUE fe CORD GRIP The washing machine should not be installed in an outdoor environment not even when the area is sheltered because it may be very dangerous to leave it exposed to rain and thunderstorms When the washing machine is installed the mains socket must be within easy reach Do not use extensions or multiple sockets The power supply cable must never be bent or dangerously compressed The power supply cable must only be replaced by an authorised serviceman Warning The company denies all liability if and when these norms are not respected The first wash cycle Once the appliance has been installed and before you use it for the first time run a wash cycle with detergent and no laundry setting the 90 C programme without a pre wash cycle Technical data Model IWDE 7145 width 59 5 cm Dimensions height 85 cm from 1 to 7 kg for the wash programme Capacity from 1 to 5 kg for the drying programme Electrical connections maximum pressure 1 MPa 10 bar Water connections depth 53 5 cm please refer to the technical data plate
19. lo to avoid this inconvenience e The wash cycle does not include draining some wash cycles require the drain phase to be started manually e The Easy iron option has been activated To complete the wash cycle press the START PAUSE button see Wash cycles and options e The drain hose is bent see nstallation e The drainage duct is clogged e The drum was not unlocked correctly during installation see Installation e The Washer dryer is not level see I nstallation e The Washer dryer is trapped between cabinets and walls see Installation e The water inlet hose is not screwed on properly see nstallation e The detergent dispenser drawer is blocked for cleaning instructions see Care and maintenance e The drain hose is not fixed properly see Installation e Switch off the machine and unplug it wait for approximately 1 minute and then switch it back on again If the problem persists contact the Technical Assistance Service e The detergent is not suitable for machine washing it should display the text for Washer dryers or hand and machine wash or the like e Too much detergent was used e The appliance is not plugged into the socket or not enough to make contact e There has been a power failure e The appliance door is not shut properly e A delayed start has been set e DRYING is in the OFF position 13 Service Before calling for
20. nce has not been altered serviced maintained dismantled or otherwise interfered with by any person not authorised by us Any repair work must be undertaken by us or our appointed agent Any parts removed during repair work or any appliance that is replaced become our property The appliance is used in the United Kingdom or Republic of Ireland The guarantee does not cover Damage resulting from transportation improper use neglect or interference or as a result of improper installation Replacement of any consumable item or accessory These include but are not limited to plugs cables batteries light bulbs fluorescent tubes and starters covers and filters Replacement of any removable parts made of glass or plastic THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON DOMESTIC PREMISES Extended Guarantees We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for the life of your policy To find the ideal plan for you please call our advice line on 08709 088 088 ROI 01 230 0233 Free Helpdesk Service We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical difficulties within the first 90 days of ownership Simply call our Indesit Service Hotline on 08709 066 066 ROI 0818 313 413 for telephone assistance or where necessary to arrange for an engineer
21. on the display when the DOOR LOCKED amp symbol switches off the door may be opened Open the door unload the laundry and switch off the machine l If you wish to cancel a cycle which has already begun press and hold the button The cycle will be stopped and the machine will switch off Wash cycles and options Table of wash cycles CID inpesit 8 Max Max Detergents Max load kg ey nti Cycle lt Description of the wash cycle pA speed Drying SFEER a duration g CC rpm Wash oftener NOMA time Daily 1 White Cotton extremely soiled whites 90 1400 7 1 White Cotton 1 heavily soiled whites and resistant colours 60 1400 e 7 D 1 White Cotton 2 heavily soiled whites and delicate colours 40 1400 T a 2 Cotton heavily soiled whites and resistant colours 60 1400 7 3 5 3 Coloured Cotton 3 lightly soiled whites and delicate colours 40 1400 o 7 3 0 4 Synthetics heavily soiled resistant colours 50 800 3 2 as Special D 5 Wool for wool cashmere etc 40 goo r e i5 5 6 Silk Curtains for garments in silk and viscose lingerie 30 O 1 zA 7 Jeans 40 800 3 5 Sport p 8 Sport Intensive 30 600 3 9 9 Sport Light 30 600 3 eJ 10 Special Shoes 30 600 p e o S Dry x 11 Cotton g g g z 5
22. quid detergent Use programme 7 Sport Intensive wash cycle 8 is for washing lightly soiled sports clothing fabrics tracksuits shorts etc for best results we recommend not exceeding the maximum load indicated in the Table of wash cycles We recommend using a liquid detergent and dosage suitable for a half load Sport Light wash cycle 9 is for washing lightly soiled sports clothing fabrics tracksuits shorts etc for best results we recommend not exceeding the maximum load indicated in the lable of wash cycles We recommend using a liquid detergent and dosage suitable for a half load Sport Shoes wash cycle 10 is for washing sports shoes for best results do not wash more than 2 pairs simultaneously Express Wash amp Dry wash cycle 13 was designed to wash and dry lightly soiled garments quickly This cycle may be used to wash and dry a laundry load of up to 0 5 kg in just 40 minutes To achieve optimum results use liquid detergent and ore treat cuffs collars and stains Load balancing system Before every spin cycle to avoid excessive vibrations and to distribute the load in a uniform manner the drum rotates continuously at a speed which is slightly greater than the washing rotation speed If after several attempts the load is not balanced correctly the machine spins at a reduced spin speed If the load is excessively unbalanced the Washer dryer performs the distribution process instead of spinning To
23. se parts separately to ensure that the appliance can no longer be plugged into a mains socket and the door cannot be locked shut 16
24. sing the drain hose collecting it in figure 3 using a screwdriver remove the cover panel o the lower front part of the Washer dryer see figure 4 pull outwards using the tab as indicated in the figure until the plastic tie rod is freed from its stop position pull downwards and open the door at the same time 5 reposition the panel making sure the hooks are securely in place before you push it onto the appliance level inside the machine is opening if it is not remove a bucket as indicated in the n 11 Care and maintenance Cutting off the water and electricity supplies e Turn off the water tap after every wash cycle This will limit wear on the hydraulic system inside the Washer dryer and help to prevent leaks e Unplug the Washer dryer when cleaning it and during all maintenance work Cleaning the Washer dryer The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water Do not use solvents or abrasives Cleaning the detergent dispenser drawer Remove the dispenser by raising it and pulling it out see figure Wash it under running water this operation should be repeated frequently Caring for the door and drum of your appliance e Always leave the porthole door ajar in order to prevent unpleasant odours from forming 12 Cleaning the pump The Washer dryer is fitted with a self cleaning pump
25. spenser drawer and pour in the detergent or washing additive as follows compartment 1 Pre wash detergent powder compartment 2 Detergent for the wash cycle powder or liquid Liquid detergent should only be poured in immediately prior to the start of the wash cycle compartment 3 Additives fabric softeners etc The fabric softener should not overflow the grid Preparing the laundry e Divide the laundry according to the type of fabric the symbol on the label the colours separate coloured garments from whites e Empty all garment pockets and check the buttons e Do not exceed the listed values which refer to the weight of the laundry when dry Durable fabrics max 7 kg synthetic fabrics max 3 kg Delicate fabrics max 2 kg Wool max 1 5 kg Silk max 1 kg How much does your laundry weigh 1 sheet 400 500 g 1 pillow case 150 200 g 1 tablecloth 400 500 g 1 bathrobe 900 1200 g 1 towel 150 250 g Special wash cycles Wool all wool garments can be washed using programme 5 even those carrying the hand wash only WH label For best results use special detergents and do not exceed 1 5 kg of laundry Silk use special wash cycle 6 to wash all silk garments We recommend the use of special detergent which has been designed to wash delicate clothes 10 Curtains fold curtains and place them in a pillow case or mesh bag Use wash cycle 6 Jeans Turn garments inside out before washing and use a li
26. t the the green indicator light flashes slowly press the machine is switched on To switch off the Washer button to start a wash cycle Once the cycle has dryer during the wash cycle press and hold the begun the indicator light will remain lit in a fixed button for approximately 2 seconds if the button Is manner To pause the wash cycle press the button pressed briefly or accidentally the machine will not again the indicator light will flash in an orange colour switch off If the machine is switched off during a If the symbol amp is not illuminated the door may be wash cycle this wash cycle will be cancelled opened To start the wash cycle from the point at which it was interrupted press the button again WASH CYCLE knob used to set the desired wash cycle see Table of wash cycles Standby mode This washing machine in compliance with new OPTION buttons with indicator light used to select energy saving regulations is fitted with an automatic the available options The indicator light corresponding standby system which is enabled after a few minutes to the selected option will remain lit if no activity is detected Press the ON OFF button briefly and wait for the machine to start up again SPIN button press to reduce or completely exclude the spin cycle the value is indicated on the display TEMPERATURE button 4 press to decrease or completely exclude the temperature the value will be shown on the display CD inbesit
27. undry into the Washer dryer make sure the drum is empty e During the drying phase the door tends to get quite hot e Do not use the appliance to dry clothes that have been washed with flammable solvents e g trichlorethylene e Do not use the appliance to dry foam rubber or similar elastomers e Make sure that the water tap is turned on during the drying cycles Disposal e Disposing of the packaging materials observe local regulations so that the packaging may be re used e The European Directive 2002 96 EC on Waste Electrical and Electronic Equipment requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment The crossed out wheeled bin symbol on the product reminds you of your obligation that when you dispose of the appliance it must be separately collected Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance Opening the porthole door manually In the event that it is not possible to open the porthole door due to a powercut and if you wish to remove the laundry proceed as follows 1 remove the plug from the electrical socket 2 make sure the water lower than the door excess water u
Download Pdf Manuals
Related Search