Philips AZ102S
Contents
1. Helpful hints During the shuffle play when REP function is selected it will play the current shuffled track repeatedly or when the REP ALL function is selected it will repeat the shuffle play of the entire CD Maintenance amp Safety See CD player and CD handling If the CD player cannot read CDs correctly use cleaning CD to clean the lens before aking the set to repair The lens of the CD player should never be ouched Sudden changes in the surrounding emperature can cause condensation on the ens of your CD player Playing a CD is then not possible Do not attempt to clean the but leave the set in a warm environment until the moisture evaporates Always close the CD door to avoid dust on he lens dean the CD wipe in a straight line from he center towards the edge using a soft int free cloth Do not use cleaning agents as hey may damage the disc Never write on CD or attach any stickers e it Safety information Place the set on a flat hard and stable surface so that the system does not tilt Where the MAINS plug or an appliance cou pler is used as the disconnect device the dis connect device shall remain readily operable Do not expose the set batteries CDs to humidity rain sand or excessive heat caused by heating equipment or direct sunlight The apparatus shall not be exposed to drip ping or splashing Ade2. markings iden tifying the terminals in your plug proceed as follows Connect the blue wire to the terminal marked or coloured black Connect the brown wire to the terminal marked L or coloured red Do not connect either wire to the earth terminal in the plug marked E or e or coloured green or green and yellow Before replacing the plug cover make certain that the cord grip is clamped over the sheath of the lead not simply over the two wires Copyright in the U K Recording and playback of material may require consent See Copyright Act 1956 and The Performer s Protection Acts 1958 to 1972 PHILIPS Meet Philips at the Internet http www philips com CLASS 1 LASER PRODUCT Printed in China AZ102 12 UM V4 0
3. the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste The correct disposal of your old product will help prevent potential negative consequences for the environment and human health N Specifications Power Consumption 15W Dimensions w x h d 290 x 143 x 240 mm 1 62 Important notes for users in the U K Mains plug This apparatus is fitted with an approved 13 Amp plug To change a fuse in this type of plug proceed as follows 1 Remove fuse cover and fuse 2 Fix new fuse which should be a BS1362 3 Amp A S LA BSI approved type 3 the fuse cover If the fitted plug is not suitable for your socket outlets it should be cut off and an appropriate plug fitted in its place If the mains plug contains a fuse this should have a value of 3 Amp If a plug without a fuse is used the fuse at the distribution board should not be greater than 3 Amp Note The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere How to connect a plug The wires in the mains lead are coloured with the following code blue neutral IN brown live L As these colours may not correspond with the colour
4. with the printed side facing up then press the CD door gently to close gt Display shows 7 and later the total number of tracks See 3 Press to start playback To pause playback press PI 3 Display flashes See 4 To resume press 1 again To stop CD playback press Helpful hints CD play will also stop when you open the CD door you select FM MW or OFF sound source the CD has reached the end Selecting a different track hints Press 144 i once or repeatedly until the desired track number appears in the display In the pause stop position press PHI to start playback When playback of your program comes to the stop position your set will return to normal playback To re enter program mode press PROG in the stop position Reviewing the program Finding a passage within a track During playback press and hold or gt The CD is played at high speed and with Erasing a program reduced volume You can erase the contents of the memory When you recognize the passage you want by release 44 or 1 to resume normal playback In the stop position press PROG repeatedly to see your stored tracks in the stop position press PROG to enter Helpful hints program mode and then press When your searching reaches the end of the selecting MW or OFF last track the CD goes to stop mode
5. AZ102C CD Soundmachine 405 21025 AZ102B Register your product and get support at AZ102F www philips com welcome AZ102H User Manual PHILIPS BR M 168 English Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome Supplied Accessories AC power cord Top front panels See 0 VOLUME adjusts volume level 2 SHUFFLE plays all tracks in random order 3 REPEAT repeats a track CD program entire CD 4 Il starts or pause CD playback gt 4 selects the next previous track searches forwards backwards press and hold the button within the current track stops CD playback erases a CD program s PROG programs tracks and reviews the program 6 LIFT TO OPEN opens closes the CD door TUNING tunes to radio stations Display shows the CD functions Back bottom panel See and 2 9 Source selector MW OFF selects CD or radio source of sound power off switch Telescopic antenna improves FM reception AC MAINS inlet for power cord DBB turns the bass e
6. Program shuffle is active Batteries dead incorrectly inserted Quit program shuffle mode Insert fresh batteries correctly Note A CD badly scratch or dirty may result in CD contains non audio files improper operation Press 44 gt gt once or more to skip to a CD audio track instead of the data file Display does not function properly No reaction to operation of any of the controls Electrostatic discharge Switch off and unplug the set Reconnect after a few seconds noc Er indication No CD inserted nsert a CD CD badly scratched or dirty Replace clean CD see Maintenance Laser lens steamed up Wait until lens has cleared CD R CD RW is blank or not finalized Use a finalized CD R CD RW or suitable CD Audio disc only Environmental information All unnecessary packaging material has been omitted The packaging can be easily separated into three materials cardboard polystyrene and plastic Your set consists of materials which can be recycled if disassembled by a specialized company Please observe the local regulations regarding the disposal of packaging dead batteries and old equipment Disposal of your old product Your product is designed and manufactured with high quality materials and components which can be recycled and reused a When this crossed out wheeled bin symbol is attached to a product it means the product is covered by
7. ical substances so they should be disposed of properly Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst not mix battery types e g alkaline with carbon zinc Only use batteries of the same type for the set When inserting new batteries do not try to mix old batteries with the new ones Remove the batteries if the set is not to be used for a long time Using AC power WARNING Always check you have completely switched off the set before you change or disconnect power supply 1 Check if the power voltage as shown the type plate located on the bottom of the set corresponds to your local power supply If it does not consult your dealer or service center 2 Connect the power cord to the AC MAINS inlet and the wall socket The set is now connected and ready for use 3 To switch the set off completely withdraw the power cord from the wall socket 4 Install the unit near the AC outlet and where the AC power plug can be easily reached General Operation Disconnect the power cord from the wall socket to protect your set during heavy thunderstorms Children could seriously injure themselves as the free end of the cable may still be live if only the connector is removed from the MAINS socket at the back of the unit The type plate is located on the bottom of the set Helpful hints To avoid unnecessary energy consumption al
8. nhancement on off LINE IN inlet for external audio source Controls Power Supply Battery door Press on the arrow and push to insert 6 x 1 5V R 14 UM 2 C cells CAUTION Visible and invisible laser radia tion If the cover is open do not look at the beam High voltage Do not open You run the risk of getting an electric shock The machine does not con tain any user serviceable parts Modification of the product could result in hazardous radia tion of EMC or other unsafe oper ation Notes for battery disposal Your product contains bat teries covered by the European Directive 2006 66 EC which cannot be disposed with normal household waste Please inform yourself about the local rules on separate collec tion of batteries because correct dispos al helps to prevent negative conse quences for the environmental and human health Power Supply Power Supply Whenever convenient use the power supply cord if you want to conserve battery life Make sure you remove the plug from the set and wall outlet before inserting batteries Batteries not included 1 Open the battery door and insert 6 batteries type R 14 UM 2 or C cells preferably alkaline with the correct polarity as indicated by the and symbols inside the compartment 2 Replace the battery door making sure the batteries are firmly and correctly in place The set is now ready to operate Batteries contain chem
9. opening the CD door Programming track numbers You may store up to 20 tracks in the desired sequence If you like store any track more than once In the stop position press PROG to activate programming 3 Display PROG and ZZ flash See 5 Press or to select your desired track number Press PROG to store the desired track number gt Display PROG and 7 flash for you to program the next track Repeat steps 2 to 3 to select and store all desired tracks in this way 3 If you attempt to store more than 20 tracks no track can be selected and the display shows 77 To play your program press P IL 2 Different play modes REPEAT and SHUFFLE See 6 71 REPEAT You can play the current track or the whole disc repeatedly and combine REPEAT modes with PROG PROGRAM REP plays the current track continuously REP ALL repeats the entire CD program To select play mode press REPEAT once or more gt The display shows REP icon or REP ALL icon Press Pill to start playback if in the stop pause position To return to normal playback press REPEAT repeatedly until the modes are no longer displayed You can also press cancel your play mode SHUFFLE You can play all the tracks in random order In the stop position press SHUFFLE to switch on shuffle play gt Display shows SHUFFLE icon To switch off shuffle play press
10. quate ventilation with a minimum gap of 15cm 6 inches between the ventilation holes and surrounding surfaces is necessary prevent heat build up Do not cover the ventilation openings with items such as newspapers table cloths cur ains etc No objects filled with liquids such as vases shall be placed on the apparatus No naked flame sources such as lighted can dles should be placed on the apparatus The mechanical parts of the set contain self lubricating bearings and must not be oiled or lubricated To clean the set use a dry cloth Do not use any cleaning agents containing alcohol ammo nia benzene or abrasives as these may harm the housing Troubleshooting If a fault occurs first check the points listed below before taking the set for repair If you are unable to remedy a problem by following these hints consult your dealer or service centre WARNING Do not open the set as there is a risk of electric shock Under no circumstances should you try to repair the set yourself as this will invalidate the guarantee Problem Note Make sure the CD is not encoded with copy right protection technologies as some do not Remedy conform to the Compact Disc standard Possible cause No sound power The CD skips tracks Volume not adjusted Adjust the VOLUME CD damaged or dirty Power cord not securely connected Replace or dean CD Connect the AC power cord properly
11. ways adjust the Source selector to OFF after using the set General operation Switching on and off and selecting the function 1 select your sound source adjust the Source selector to CD FM or MW 2 To switch off the set adjust the Source selector to OFF position 3 To switch to LINE IN mode connect an external audio source to the LINE IN inlet Helpful hints The set switches to LINE IN mode automatically when an external audio source is connected no matter the set is in CD FM or MW mode The LINE IN inlet is not for earphones Adjusting volume and sound Adjust the sound with the VOLUME and DBB controls Radio reception 1 Adjust the Source selector to FM or MW 2 Turn TUNING to tune to a station Helpful hints To improve radio reception e For FM extend incline and turn the telescopic antenna for best reception Reduce its length if the signal is too strong e For MW the set uses a built in antenna Direct this antenna for best reception by turning the whole set Playing a CD This CD player plays Audio Discs including CD Recordables CD R and CD Rewritables CD RW CD ROM CD I DVD or computer CDs are not possible for playback IMPORTANT CDs encoded with copyright protection technologies by some record companies may be unplayable by this product Adjust the Source selector to CD 2 Open the CD door and insert a CD
Download Pdf Manuals
Related Search