StarTech.com 3 Port PCI 12V Adapter Card
Contents
1. Instruction Manual Jumper Settings JP2 24V Selector Settings Default The power source of the 24V keyed Pow eredUSB connector is supplied from the internal step up switching regulator jumpers must be set identically both at INT or EXT The power source of the 24V keyed Powered USB connector is supplied from the external Power DIN input connector in this case a 24V AC adapter will be required Please see http www startech com for more information Hardware Installation PCI312PUSB LP PEX312PUSB LP amp PUSBADAP LP This section details how to install PCI312PUSB PEX312PUSB in conjunction with a daughter board PUSBADAP 1 Remove the computer cover For more detailed instruction on how to perform this step please refer to the documentation that was included with your computer at the time of purchase 2 Locate an empty PCI PCI Express slot and remove the metal bracket covering the accompanying empty port socket 3 Connect one end of the 9 pin Header Cable provided by PUSBAD LP to the expansion port depicted on pg 2 as J4 USB Ports 4 5 4 Position the card above the open PCI PCI Express slot ensuring that the card is properly aligned with the slot Insert the card firmly into the slot distributing force evenly across the length of the board then fasten the metal bracket to the computer case using the screw removed in step 2 4 Instruction Manual 5 R2. I312PUSB PEX312PUSB as a stand alone card 1 Remove the computer cover For more detailed instruction on how to perform this step please refer to the documentation that was included with your computer at the time of purchase 5 Instruction Manual 2 Locate an empty PCI PCI Express slot and remove the metal bracket covering the accompanying empty port socket 3 Position the card above the open PCI PCI Express slot ensuring that the card is properly aligned with the slot Insert the card firmly into the slot distributing force evenly across the length of the board then fasten the metal bracket to the computer case using the screw removed in step 2 if necessary 4 By default JP2 see pg 3 is set to PCI commanding the card to draw power via the PCI slot into which it is installed As such if you ve left the JP2 jumper in the default position there will be no need to connect PCI312PUSB to the computer power supply If JP2 has been switched to INT Internal you must connect PCI 312PUSB to the computer power supply by inserting an available LP4 connector into the AUX Power Connector 5 Once the card is properly seated and secured to the computer case close the computer case and power on the computer PUSBADAP PUSBADAPLP Only This section details how to install PUSBADAP as a stand alone card 1 Remove the computer cover For more detailed instruction on how to perform this step please refer to the documentation tha
3. PCISIPUSB LP amp PEX312PUSB LP PCI PCle LN Powered USB Card PUSBADAP LP AVIA 119 StarTech com Making hard to find easy FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turn ing the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Use of Trademarks Registered Trademarks and other Protected Names and Symbols This manual may make reference to trademarks registered trademarks and other protected names and or symbols of third party companies not related in a
4. S 9 Warranty Information ccccecssseeseeesteesseeseeesnessseeeseeseeeneneeees 9 Instruction Manual Introduction Thank you for purchasing a StarTech com Powered USB 2 0 Adapter Card available in both PCI and PCI Express formats as well as Standard and Low Profile Now adding Powered USB capability to a computer has never been easier Fully compatible with USB1 1 OHCI and USB2 0 ECHI specifications the cards support data speeds of up to 480 Mbps and provide power to Pow ered USB devices through industrial standard Powered USB connectors Features e Supplies power and data signals over hot pluggable USB cable e Mainboard can be linked to daughter board e Daughter board and Main board can be used as stand alone devices e Selectable power input e Connectors offer cable locking mechanism Package Contents e PCI312PUSB LP 1 x Powered USB Mainboard Card or PEX312PUSB LP 1 x Powered USB Mainboard Card or PUSBADAPILP 1 x Powered USB Daughter Board e Instruction Manual e Driver CD PCI312PUSB LP and PEX312PUSB LP only e 9 Pin USB Header Cable PUSBADAP LP Only Please note that the Powered USB ports are color coded based on volt age capabilitythey support as follows Yellow 5V Green 12V Red 24V Instruction Manual Hardware Guide PCI312PUSB LP PEX312PUSB LP J4 USB Ports 4 5 J1 J3 External Powered USB Ports x3 for Expansion 5 45 D Lfe D D feft D ath
5. cal support is an integral part of our commit ment to provide industry leading solutions If you ever need help with your product visit www startech com support and access our comprehensive selection of online tools documentation and downloads Warranty Information This product is backed by a lifetime warranty In addition StarTech com warrants its products against defects in materials and workman ship for the periods noted following the initial date of purchase During this period the products may be returned for repair or replacement with equivalent products at our discretion The warranty covers parts and labor costs only StarTech com does not warrant its products from defects or damages arising from misuse abuse alteration or normal wear and tear Limitation of Liability In no event shall the liability of StarTech com Ltd and StarTech com USA LLP or their officers directors employees or agents for any damages whether direct or indirect special punitive incidental consequential or otherwise loss of profits loss of business or any pecuniary loss arising out of or related to the use of the product exceed the actual price paid for the product Some states do not allow the exclusion or limitation of incidental or consequential damages If such laws apply the limitations or exclusions contained in this statement may not apply to you 10 StarTech com Making hard to find easy StarTech com has been making
6. e Jumper Settings 12V Selector JP2 J5 AUX Power JP1 5V Selector JP1 5V Selector Default The USB2 0 Bus Power is supplied by the motherboard PCI slot DC 5V supplied from PCB Settings power supply The USB2 0 Bus Power is supplied by the AUX power connector J5 This option provides more power for Powered USB devices but requires a connection to the computer Instruction Manual Jumper Settings Cont d JP2 12V Selector Settings Default The 12V power source of the Powered USB connectors are supplied by the PCI slot into which the card is installed The 12V power source of the Powered USB con nectors are supplied by the AUX power connector J5 This will require that a power cable be con nected from the computer power supply to J5 This option provides more power for the Powered USB devices over the USB2 0 cable PUSBADAP PUSBADAPLP JT USB Input Connector JP1 24V Power from Host USB port Source Selector 5 op 45 from Regulator B oo GN or External Power ce Hag DIN connector J3 External Input Power K DIN Connector E J5 lt AUX Power Connector J4 7 1 Ges 24V keyed gt Connector Power DIN Connector Pin J2 Le Assignment 12V Keyed Connector
7. emove a metal bracket that is adjacent to or near the one removed in step 2 and fasten PUSBADAP PUSBADAPLP directly to the metal rear panel of the computer case 6 Connect the remaining end of the 9 Pin USB Header Cable used in step 3 to the USB IN connector denoted as J1 USB Input Connector from Host USB port see diagram pg 3 on the PUSBADAP board 7 PCI312PUSB PEX312PUSB By default JP2 see pg 3 is set to PCI The card will draw power via the PCI PCI Express slot into which it is installed as such if you ve left the JP2 jumper in the default position there will be no need to connect PCI312PUSB to the computer power supply If JP2 has been switched to INT Internal you must connect PCI 312PUSB PEX312PUSB to the computer power supply by inserting an available LP4 connector into the AUX Power Connector PUSBADAP By default JP2 is set to INT commanding the card to draw power from the computer power supply As such insert an LP4 power connector from the power supply into the AUX Power Connector If JP2 has been set to EXT the PUSBADAP will draw power through the External Input Power DIN Connector and will require an external power source see http www startech com for accessories 8 Once both cards have been properly positioned and the necessary link has been made between them close the computer case and power on the computer PCI312PUSB LP or PEX312PUSB LP Only This section details how to install PC
8. hard to find easy since 1985 providing high quality solutions to a diverse IT and A V customer base that spans many channels including government education and industrial facilities to name just a few We offer an unmatched selection of computer parts cables A V products KVM and Serv er Management solutions serving a worldwide market through our locations in the United States Canada the United Kingdom and Taiwan Visit www startech com today for complete information about all our products and to access exclusive interactive tools such as the Cable Finder Parts Finder and the KVM Reference Guide StarT ech com makes it easy to complete almost any IT or A V solution Find out for yourself why our products lead the industry in perfor mance support and value
9. ny way to StarTech com Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech com or an endorsement of the product s to which this manual applies by the third party company in question Regardless of any direct acknowledgement elsewhere in the body of this document StarTech com hereby acknowl edges that all trademarks registered trademarks service marks and other protected names and or symbols contained in this manual and related documents are the property of their respective holders Table of Contents deet UO d EE 1 Feature Sairaan nsan aeree Sha ar TE E Arae EATEN TREE ERNE 1 Package Contents sccsscsosscssccscscescasesstsasscdbaccesatscasteussetsicensazses 1 Hardware Guide iiccscccecccscccccssetiececenecs concoct ceases cesseecssccebsstactucestecessece 2 PCISA2PUSB L_P PEX312PUSB L Pes tiisak adara 2 JUMPOSF S CHING EE PUSBADAP PUSBADAPLP Hardware Installation cccssssssecesseeessssssceeeeeeeneesseeeeeeeeeneeeseees 4 PCI312PUSB LP PEX312PUSB LP amp PUSBADAPILP wid PCI312PUSB LP or PEX312PUSB LP On 5 PUSBADAP PUSBADAPLP Only ceeeeeeeeeeeeeeeeeeeeeeeeee 6 Software Installation c cccscccsssseesssseessseceeessaceessseseesseneenseeeeens 7 SPECIFICATIONS 2 eccsceseccscieisesevcstctseecsctedascesivereesoterccerssecdudervsteszccerstes 8 Technical SODDOrEeeseeeeeeseeesgechee e tee dee cece ee ces EE
10. t was included with your computer at the time of purchase 2 Connect one end of the 9 Pin USB Header Cable provided to the USB IN connector denoted as J1 USB Input Connector from Host USB port see diagram pg 3 on the PUSBADAP board 3 By default JP2 is set to INT commanding the card to draw power from the computer power supply As such insert an LP4 power connector from the power supply into the AUX Power Connector If JP2 has been set to EXT the PUSBADAP will draw power through the External Input Power DIN Connector 4 Connect the remaining end of the 9 Pin USB Header Cable see step 6 Instruction Manual 2 to the USB Header connector on the host motherboard For further instructions on how to locate the appropriate connection on the motherboard please consult the documentation that was included with your motherboard computer at the time of purchase Software Installation PCI312PUSB LP and PEX312PUSB LP are natively supported by Win dows XP SP2 2000 SP4 and Vista As such no driver installation is required as long as the necessary updates have been made to the operating system s For Windows 98SE or Windows ME installations however driver instal lation is required To install the drivers necessary for PCI312PUSB LP or PEX312PUSB LP to function properly 1 With the host computer powered on insert the Driver CD that accompanied your purchase of PCI312PUSB PCI312PUSBLP into the CD DVD ROM dri
11. ve 2 On the Driver CD browse to the X USB 2 0 NEC folder where X de notes the designated CD DVD ROM drive on the host computer and locate the folder that corresponds with the host computer operating system 3 Open the appropriate folder and locate the U2v2_1 application file Execute the file by double clicking on the icon listing to begin installation 4 Follow the installation through until you are asked if you would like to reboot the computer Select Yes want to restart my computer now and click on Close Once the computer has rebooted the operating system will detect the presence of the card installation is complete Instruction Manual Instruction Manual PCI312PUSB PEX312PUSB PUSBADAP 3 x 12V Powered USB male connectors 1x 12v Power USB Connector 1x 24v Power USB Connector Connectors 1 x LP4 Connector 1x 4 pin Power Din Connector 1 x Internal USB 9 pin Header 1x Internal USB Connector Connector for expansion 1x Jumper Connector 1x LP4 Connector 1x Jumper Connector OS Support Windows 2000 ME 2003 XP Vista Dimensions 81 2 mm x 66 7 mm 120 mm x 66 7 mm L xW 3 2 in x 2 63 in 4 72 in x 2 63 in Regulatory Certified CE RoHS FCC Maximum Data Transfer 480Mbps Rate NEC D720101GJ NEC TI XIO2000A Chipset PCI Express N A D720101GJ to PCI Bus Translation Bridge Instruction Manual Technical Support StarTech com s lifetime techni
Download Pdf Manuals
Related Search