Autodesk AutoSketch 10, Commercial Full, EN
Contents
1. 16 Tutorial 3 Create an Office Layout Drawing You are ready to add the furniture to the office layout Add Furniture In this exercise you learn to Choose symbols by using the Wizard Tools toolbar and the Content Librarian Add a workstation symbol to the interior office Move and rotate a symbol Place symbols in precise locations using the Absolute Coordinates dial Once the interior walls doors and windows are in the drawing you can add a workstation and other furniture to the office 1 On the Wizard Tools toolbar click the Private Offices button On the right side of the AutoSketch window the Content Librarian dis plays thumbnail images of different private offices 2 In the Content Librarian locate RPrivOffProSta The symbol is an office workstation Add Furniture 17 3 Click RPrivOffProSta and drag it into the interior office section of the drawing Do not release the mouse button yet 4 On the keyboard press the F5 key until the office workstation is rotated counter clockwise and the desk and chairs are on the right side in the inte rior office SHIFT F5 rotates the workstation clockwise Tip You can also use the numeric keypad on the right side of the keyboard to rotate entities To rotate entities clockwise press the minus sign To rotate entities counter clockwise press the plus sign 5 Click to place the workstation and then right click to end the command Your dra2. Then move the pointer up and to the left slightly and click to place the door so that it opens into the interior office space 7 Right click to end the command Your drawing should match the following illustration 8 Save your work Now add some windows to the office space 14 Tutorial 3 Create an Office Layout Drawing To add windows 1 On the Wizard Tools toolbar click and hold the Doors button 2 On the toolset drag the pointer to select Windows On the right side of the AutoSketch window the Content Librarian dis plays thumbnail images of different office window sizes and types 3 In the Content Librarian locate SingleFixWin60 You add this window type to two locations in your drawing 4 Click and hold SingleFixWin60 and drag it on the side wall at the upper left as shown in the following illustration Add Doors and Windows 15 5 With the symbol still active click the top wall at the upper left to place the second window there as shown in the following illustration Then right click to end the command Next add a slightly larger window to two locations outside the internal office 6 In the Content Librarian click and hold SingleFixWin72 and drag it to the top wall close to the right side Click again to place the symbol 7 Click the vertical wall close to the top Then right click to end the command Your drawing should look similar to the following illustration 8 Save your work
3. by setting dimensions adding a title to the draw ing and placing the entities on appropriate layers Use what you learned in the second tutorial Create a Birdhouse Drawing to complete this drawing Remember that you can always get detailed information from the Help system by clicking AutoSketch Help on the Help menu 22
4. suit your project You can always change the options after you ve completed the wizard This tutorial guides you through using the wizard To start a drawing using the Office Layout wizard 1 In the Start Up dialog box Wizard tab select Office Layout 2 Click OK On the next page of the wizard you set the size of the building that con tains your office space You also set the thickness of the walls Start a Drawing Using the Office Layout Wizard 3 3 Do the following In the row of office shell buttons click the square shape the first shape In the A box enter 25 for the length In the B box enter 15 for the width In the Wall Thickness box enter 0 6 4 Click Next The next page of the wizard lists database reports that you can add to your drawing 4 Tutorial 3 Create an Office Layout Drawing 5 Clear all of the check boxes on this page You don t need database reports in this tutorial Click Next On the next page of the wizard select the layers for the drawing and the fields in the database Note Because you did not select any database reports on the previous wizard page AutoSketch will ignore the Fields settings So you can leave the database fields as they are preset on this page 6 In the Layers list clear the check boxes next to Electrical Cable Equip ment Panel and Personnel Then click Next Now choose the page orientation that best displays the office
5. September 2008 AutoSketch 10 Create an Office Layout Drawing 2008 Autodesk Inc All rights reserved Except as otherwise permitted by Autodesk Inc this publication or parts thereof may not be reproduced in any form by any method for any purpose Certain materials included in this publication are reprinted with the permission of the copyright holder Trademarks The following are registered trademarks or trademarks of Autodesk Inc in the USA and other countries 3DEC design logo 3December 3December com 3ds Max ADI Alias Alias swirl design logo AliasStudio Alias Wavefront design logo ATC AUGI AutoCAD AutoCAD Learning Assistance AutoCAD LT AutoCAD Simulator AutoCAD SQL Extension AutoCAD SQL Interface Autodesk Autodesk Envision Autodesk Insight Autodesk Intent Autodesk Inventor Autodesk Map Autodesk MapGuide Autodesk Streamline AutoLISP AutoSnap AutoSketch AutoTrack Backdraft Built with ObjectARX logo Burn Buzzsaw CAiCE Can You Imagine Character Studio Cinestream Civil 3D Cleaner Cleaner Central ClearScale Colour Warper Combustion Communication Specification Constructware Content Explorer Create gt what s gt Next gt design logo Dancing Baby image DesignCenter Design Doctor Designer s Toolkit DesignKids DesignProf DesignServer DesignStudio Design Studio design logo Design Web Format DWF DWG DWG logo DWG Extreme DWG TrueConvert DWG TrueView DXF Ecotect Exp
6. alog box To set units reference grid and scale 1 In a blank area of the drawing right click and then click Drawing Options 2 In the Drawing Options dialog box Units tab under Length click the arrow to the right of the Decimal Precision box and select 1 from the list 3 On the Grid tab select the Rectangular subtab as shown in the following illustration and then change these settings In the Snap Interval box enter 6 In the Major Interval box enter 1 8 Tutorial 3 Create an Office Layout Drawing 4 On the Scale tab select the Architectural subtab as shown in the follow ing illustration In the list of scale settings select 1 4 1 5 Click OK to close the Drawing Options dialog box and save your changes Create Office Partition Walls 9 The drawing should now match the grid settings in the following illustration Now that you have set the units reference grid and scale of the office layout you can create the partition walls of the office Create Office Partition Walls In this exercise you learn to Add a partition wall to the office space Zoom to display all entities in the drawing using the Extent command Choose a corner polyline using the Wizard Tools toolbar Set the width and lengths of the walls using the edit bar To create office partition walls 1 On All In One toolbar click and hold the Zoom button 2 On the Zoom toolset drag the pointer to sel
7. ames or trademarks belong to their respective holders Disclaimer THIS PUBLICATION AND THE INFORMATION CONTAINED HEREIN IS MADE AVAILABLE BY AUTODESK INC AS IS AUTODESK INC DISCLAIMS ALL WARRANTIES EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE REGARDING THESE MATERIALS Published by Autodesk Inc 111 Mclnnis Parkway San Rafael CA 94903 USA 1 Tutorial 3 Create an Office Layout Drawing In this tutorial you learn how to use the Office Layout wizard to set up a drawing You also learn how to set units grid and scale for the drawing use symbols to represent the interior components of your drawing replace symbols and create a circular array More information about each of the concepts in this tutorial is available in the Help system In this tutorial Start a Drawing Using the Office Layout Wizard Set Units Reference Grid and Scale Create Office Partition Walls Add Doors and Windows Add Furniture Create a Round Table and Chairs 2 Tutorial 3 Create an Office Layout Drawing Start a Drawing Using the Office Layout Wizard In this exercise you learn to Set up an office layout drawing using the Office Layout wizard The Office Layout wizard like the other wizards provided by AutoSketch steps you through predefined options to create a drawing that will best
8. at are available to you in AutoSketch You can see how powerful this feature is by using symbols in your office layout To add doors and windows 1 On the Snap toolbar click the Snap button to turn off Snap settings Note When Snap settings are turned off all of the buttons in the toolbar are deselected as shown in the following illustration You won t need to use precision snap settings in this exercise 2 On the Wizard Tools toolbar click the Doors button On the right side of the AutoSketch window the Content Librarian dis plays thumbnail images of different door sizes and types 12 Tutorial 3 Create an Office Layout Drawing 3 In the Content Librarian locate Door 3 6 a door that is 3 ft 6 inches wide 4 Click Door 3 6 and drag it into the drawing When the symbol is close to the bottom left corner of the drawing release the mouse button Then move the pointer up slightly and click to place the door so that it opens into the office space Tip You can always undo an action like the placement of the door by pressing CTRL Z on the keyboard 5 Right click to end the command Your drawing should match the following illustration Add Doors and Windows 13 Next add a door to the interior office 6 In the Content Librarian click and hold Door 3 0 and drag it into the drawing When the vertical part of the symbol is close to the bottom right corner of the interior office release the mouse button
9. eating each chair individually create one chair by rubber stamping an existing chair Then create a circular array a selection set arranged in a circular pattern of four chairs arranging them around the table 6 In the interior office space on the left side of the drawing click the chair that faces the other two chairs 7 On the All In One toolbar click Rubber Stamp Then drag the rubber stamped chair and when the Absolute Coordinates dial reads 16 6 9 6 click to place the chair next to the round table Then right click to end the command Your drawing should match the following illustration 8 Click the chair you just created to select it 20 Tutorial 3 Create an Office Layout Drawing 9 On the All In One toolbar click and hold the Rubber Stamp button 10 On the toolset drag the pointer to select Circular Array 11 In the Circular Array dialog box in the Angular Duplication area select the Regular option and enter 4 in the first box and 72 in the second Then click OK Create a Round Table and Chairs 21 12 In the drawing window move the pointer over the edge of the table until the Centerpoint snap is displayed Then click to add the arrayed chairs Your drawing should match the following illustration Great work You have completed the third tutorial You should now be able to create entities place symbols set dimensions add layers use wizards and create arrays You can finish this drawing
10. ect View Extent The drawing window now includes the entire office shell 3 On the Wizard Tools toolbar click Corner Polyline The edit bar displays tools related to editing a corner polyline The pointer in the drawing window changes to a hollow circle 10 Tutorial 3 Create an Office Layout Drawing 4 On the edit bar in the Width box enter 0 6 This sets the wall width to match the one you selected for the building in the Office Layout wizard Now set the length of the first wall 5 On the edit bar in the Corner Length 1 box enter 10 8 Then set the length of the second wall 6 On the edit bar in the Corner Length 2 box enter 14 0 7 In the drawing click the wall on the left side and then click the wall at the top to place the wall 8 Right click to end the command The interior walls you defined using the edit bar are now displayed in the drawing 9 Save your work Now it s time to create the doors and windows in the office layout Add Doors and Windows 11 Add Doors and Windows In this exercise you learn to Choose symbols by using the Wizard Tools toolbar and the Content Librarian Add doors and windows to precise locations in your drawing Up to this point you have created your own lines arcs polygons and other entities to represent elements in your drawings In this exercise you learn how to use just a few of the thousands of predrawn entities called symbols th
11. layout Start a Drawing Using the Office Layout Wizard 5 7 Select Landscape from the list and then click Next On the next page of the wizard you can select a grid setting Because you will set a specific grid setting in the next exercise you can accept the pre selected setting Paneling on this page 8 Click Next Now choose a toolbar to display in the drawing window 9 In the Toolbars box click the check box next to Symbol Library You will use that toolbar later 10 Below the Toolbars box clear the check box next to the Help icon Then click Finish You have just completed the Office Layout wizard 6 Tutorial 3 Create an Office Layout Drawing In the AutoSketch window the following drawing is displayed 11 On the File menu click Save 12 In the Save Drawing File dialog box navigate to the following location C Program Files Autodesk AutoSketch10 Drawings 13 In the File Name box enter My_Office and then click Save Next set units a reference grid and the scale Set Units Reference Grid and Scale 7 Set Units Reference Grid and Scale In this exercise you learn to Right click to access the Drawing Options dialog box Set units reference grid and scale in the Drawing Options dialog box The office layout drawing you are creating requires some adjustment of the preset units reference grid and scale settings You can adjust all of these settings in the Drawing Options di
12. osure Extending the Design Team FBX Filmbox FMDesktop Freewheel GDX Driver Gmax Green Building Studio Heads up Design Heidi HumanIK IDEA Server i drop ImageModeler iMOUT Incinerator Inventor Inventor LT Kaydara Kaydara design logo Kynapse Kynogon LandXplorer LocationLogic Lustre Matchmover Maya Mechanical Desktop MotionBuilder Movimento Mudbox NavisWorks ObjectARX ObjectDBX Open Reality Opticore Opticore Opus PolarSnap PortfolioWall Powered with Autodesk Technology Productstream ProjectPoint ProMaterials RasterDWG Reactor RealDWG Real time Roto REALVIZ Recognize Render Queue Retimer Reveal Revit Showcase ShowMotion SketchBook SteeringWheels Stitcher StudioTools Topobase Toxik TrustedDWG ViewCube Visual Visual Construction Visual Drainage Visual Landscape Visual Survey Visual Toolbox Visual LISP Voice Reality Volo Vtour Wiretap and WiretapCentral The following are registered trademarks or trademarks of Autodesk Canada Co in the USA and or Canada and other countries Backburner Discreet Fire Flame Flint Frost Inferno Multi Master Editing River Smoke Sparks Stone and Wire The following are registered trademarks or trademarks of Moldflow Corp in the USA and or other countries Moldflow MPA MPA design logo Moldflow Plastics Advisers MPI MPI design logo Moldflow Plastics Insight MPX MPX design logo Moldflow Plastics Xpert All other brand names product n
13. wing should look similar to the following illustration You have rotated and placed the workstation in the interior office space 6 On the File menu click Save You are ready to create a table and chairs for the outer office 18 Tutorial 3 Create an Office Layout Drawing Create a Round Table and Chairs In this exercise you learn to Create a round table using the All In One toolbar and the edit bar Set a precise radius using the edit bar Use the Absolute Coordinates dial to place items in precise locations Rubber stamp an existing chair and place it in another location Create a circular array of four additional chairs that are placed around the table To create a round table and chairs 1 On the Snap toolbar click Snap to turn on snap settings you turned them off earlier when you placed the doors and windows 2 On the All In One toolbar click and hold the Circle button 3 On the toolset drag the pointer to select Center Radius Circle The edit bar displays tools related to editing a center radius circle The pointer becomes a hollow circle with four points 4 On the edit bar set the radius to 2 0 5 On the right side of the drawing click when the Absolute Coordinates dial shows 19 0 10 0 Then right click to end the command Your drawing should match the following illustration Create a Round Table and Chairs 19 Now place five chairs around the round table Instead of cr
Download Pdf Manuals
Related Search