Philips Professional LCD TV 26HFL3350D
Contents
1. 2 Continue with the instructions provided with your VESA compatible wall bracket EN 9 NOTE When securing the VESA compatible wall bracket to your TV use M4 bolts for 26 inch models M6 bolts for 32 inch models or M8 bolts for larger models bolts not supplied 4 3 Connect the antenna cable a gt a a of 1 Locate the TV ANTENNA connector at the back of the TV 2 Connect one end of an antenna cable not supplied to the TV ANTENNA connector Use an adaptor if the antenna cable does not fit 3 Connect the other end of the antenna cable to your antenna outlet ensuring that the cable is tightly secured at both ends 4 4 Connect the mains cord A WARNING Verify that your mains voltage corresponds with the voltage printed at the back of the TV Do not insert the mains cord if the voltage is different 1 Locate the AC IN mains connector at the back or on the bottom of the TV 2 Connect the mains cord to the AC IN mains connector 3 Connect the mains cord to the mains ensuring that the cord is tightly secured at both ends WARNING Before you connect the TV to the power outlet ensure that the power voltage matches the value printed under the cable cover To easily disconnect the TV from the power outlet ensure that you have full access to the power cord at all times When you disconnect2. 23 9 Trouble shooting 24 9 1 Communication issues 24 9 2 Picture issues 24 93 Other issues ensen 24 10 HdE en varen eere ee ee de ee 25 EN 1 2008 Koninklijke Philips Electronics N V All rights reserved Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly The material in this manual is believed adequate for the intended use of the system If the product or its individual modules or procedures are used for purposes other than those specified herein confirmation of their validity and suitability must be obtained Philips warrants that the material itself does not infringe any United States patents No further warranty is expressed or implied Warranty e Risk of injury damage to TV or void of warranty Never attempt to repair the TV yourself e Use the TV and accessories only as intended by the manufacturer e The caution sign printed on the back of the TV indicates risk of electric shock Never remove the TV cover Always contact Philips for service or repairs RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR nd ADVERTENCIA NO ABRIR RIESGO DE CHOQUE ELECTRICO e Any operation expressly prohibited in this man
3. Press A or v to select options or make adjustment e Display standby Set the brightness level of the clock display when the TV is in standby mode e Display ON Set the brightness level of the clock display when the TV is switched on Time setting Set the time of the clock display manually 6 Note This option is only available if Time download is OFF Time download Set the time of the clock display automatically via Teletext The clock will be automatically synchronised to the correct time Download Program Select the time from the teletext transmission of a channel Make this download program the same as the startup channel Time offset Set the time difference between the time received from Teletext to the current time at your location Buzzer volume Set the volume of the alarm buzzer Press w to select Store go right and press gt to save setting 7 12 Set auto scart Set the TV to switch to the source where scart signal is detected 1 2 Enter Setup menu Press w to select Auto scart j Setup menu Auto scart Maximum volume 100 Switch on channel Power on Low power standby Clock Auto scart USB break in Monitor out Press gt to enter Auto scart Press A or W to select the desired option AV1 Select to switch TV automatically to AV1 when scart cable is connected to the AV1 connector Power ON SCART Select to switch the TV on from standby mode wh
4. a J 3 Switch on the TV and wait for the CAM to be activated This may take several minutes 6 Note Do not remove the CAM from the slot Removing the CAM will deactivate the digital services 4 6 2 Access CAM services Enter Setup menu Press v to select OSD display gt Enable CI slot Press A to select On EN 11 42 OSD display Enable Cl slot OSD display Display message Welcome message line 1 Welcome message line 2 Welcome message ti Enable CI slot Enable teletext Enable MHEG 4 Press MENU or M to exit EN 12 5 Remote control overview This section provides a detailed overview of remote control features Ci 1 GUIDE 19 e 2 18 zed co usr av i dn e e e e 5 ALARM ALARM Ger 6 OFF 17 Ca j s5 Ce el j Ee 8 9 er Ae 13 ij ee o je 12 PHILIPS TELEVISION w ox 10 11 12 13 14 15 16 17 0 Switches the TV on from standby or back to standby GUIDE Toggles the Electronic Programme Guide on or off Only active with digital channels AV Selects connected devices SUBTITLE Activates or deactivates subtitles Colour keys Selects tasks teletext pages ALARM OFF Deactivates the alarm function Only for
5. gt to enter OSD display Press A or to select a setting Press gt to enter OSD display On Display normal screen information Off Suppress screen information Display message On Display the welcome message after the TV set is turned on Off Disable the welcome message Welcome message line 1 2 Press A or W to create the first or second line of the welcome message You can create up to a maximum of 20 alphanumeric characters for each line Press the red button to cancel green button to exit yellow button to clear all the characters or blue button to delete any character Welcome message timeout Select the time out period for the welcome message Enable Cl slot Select On to access CAM services Enable teletext Select On to access teletext Enable MHEG Select On to access MHEG Enable EPG Select On to access EPG Enable Subtitles Select On to display subtitles 7 6 Set switch on volume When the user switches the TV on it will play at the specified volume level set 1 Enter Setup menu 2 Press w to select Switch on volume 3 Press p to enter Switch on volume Switch on volume Setup menu BDS mode Local keyboard locked Remote control OSD display Switch on volume Maximum volume 100 Switch on channel Power on 4 Press A or w to select the desired volume level 5 Press v to select Store go right and press gt t
6. legal requirements and to stay well within the EMF standards applicable at the time of producing the products Philips is committed to develop produce and market products that cause no adverse health effects Philips confirms that if its products are handled properly for their intended use they are safe to use according to scientific evidence available today Philips plays an active role in the development of international EMF and safety standards enabling Philips to anticipate further developments in standardisation for early integration in its products Mains fuse UK only This TV is fitted with an approved moulded plug Should it become necessary to replace the mains fuse this must be replaced with a fuse of the same value as indicated on the plug example 10A 1 Remove fuse cover and fuse 2 The replacement fuse must comply with BS 1362 and have the ASTA approval mark If the fuse is lost contact your dealer in order to verify the correct type 3 Refit the fuse cover In order to maintain conformity to the EMC directive the mains plug on this product must not be detached from the mains cord Copyright VESA FDMI and the VESA Mounting Compliant logo are trademarks of the Video Electronics Standards Association Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and or other countries Kensington and Micro Saver are registered US trade
7. the European Directive 2002 96 EC Never dispose this product with other household waste Inform yourself or ask your dealer about local environmentally safe recycling regulations The correct disposal of your old product helps prevent potentially negative consequences on the environment and human health The remote control supplied with this product operates on batteries covered by the European Directive 2006 66 EC and cannot be disposed with normal household waste Inform yourself about the local regulations on the separate collection of batteries EN 5 Your TV Connection overview EXT 1 First SCART connector for DVD players VCRs digital receivers game consoles and other SCART devices Supports Audio L R CVBS in out RGB EXT 2 Second SCART connector Supports Audio L R CVBS in out EXT 3 Component video Y Pb Pr and Audio L R input connectors for DVD players SPDIF OUT AUDIO OUT Sound output connectors for home theatres or other audio systems SERV U Connector for service use do not insert the headphones here EN 6 10 11 12 HDMI 1 2 3 HDMI input connectors for Blu ray disc players digital receivers game consoles and other high definition devices AUDIO IN Mini jack connector for PC audio in when connecting a PC via DVI HDMI adaptor TV ANTENNA IR LINK Connector for an IR link compliant device e g set top box
8. AUDIO L R Audio L R input connectors for composite and S Video devices VIDEO Video input connector for composite devices S VIDEO S Video input connector for S Video devices 13 USB USB connector for storage devices 14 HDMI Additional HDMI connector for mobile high definition devices 15 COMMOM INTERFACE Slot for Conditional Access Modules Note Refer to the user manuals for the respective devices for details of connection 2 1 1 Side controls and indicators FA gt voe 4 O 3 ooa 2 e 1 5 1 POWER 2 PROGRAM 3 MENU 4 VOLUME 5 Power indicator remote control sensor 6 Clock EN 7 3 Remote control For advanced information about the remote control see Chapter 5 Remote control overview Guest mode remote control For setup and configuration purposes e Gerd CO SESSIES ALARM ALARM DOE DE PHILIPS EN 8 Setup remote control This remote control may be purchased separately for Institutional TV Professional and Business Solutions features and SmartCard settings TEXT SMART SLEI Lj 5 0 Peso 0 0000 B 5 m 000 PHILIPS STV 4 Get started This section helps you position and install the TV 41 Position the TV In addition to reading and und
9. with setup remote control 16 Side Controls 7 EN 26 SPDIF OUT 6 S VIDEO 6 T Trouble shooting 24 TV 9 antenna 6 connection overview 6 position 9 prepare for digital services 11 setup 15 side controls 7 stand 9 USB 7 Vv VESA 3 compatible wall bracket 9 VIDEO 6 Volume buzzer 21 maximum 19 switch on 19 W Warranty 2 PHILIPS 2008 Koninklijke Philips Electronics N V All rights reserved
10. Philips Professional and Business Solution 22HFL3350D 26HFL3350D 32HFL3350D PHILIPS EN SETUP MANUAL PHILIPS Table of contents 1 Important 00 e eee eee WA Safety eeen Netra es 1 2 Screen care 13 Recycling ons stenen imss 2 YoUrTV verrees eee 2 1 Connection overview 3 Remote control 4 Get started 41 Position the TV 42 Wall mount the TV 4 3 Connect the antenna cable 44 Connect the mains cord 4 5 Insert the remote control batteries 4 6 Prepare TV for digital services 5 Remote control overview 6 First time setup 7 Setup BDS mode 7 1 Access setup menu 7 2 Switch on BDS mode 7 3 Lock local keyboard 74 Select remote control setting 7 5 Select OSD display 7 6 Set switch on volume 7 7 Set maximum volume 7 8 Select switch on channel 7 9 Set power on status 7 10 Set low power standby 711 Select clock settings 10 11 7 12 Set auto scart 21 7 13 Set USB break in 21 7 14 Select monitor out 21 7 15 Select blank current channel 22 7 16 Save settings 22 8 Clone configuration 23 8 1 From Cloning toTV 23 82 FromTV to Cloning
11. en a scart signal is detected or when no scart signal is detected the TV will go to standby mode Off Switch off this feature 5 Press v to select Store go right and press gt to save setting 7 13 Set USB break in Set the TV to automatically detect USB devices 1 Enter Setup menu 2 Press w to select USB break in N Setup menu USB break in Switch on channel Power on ejjj Low power standby Clock Auto scart USB break in Monitor out Blank current Channel 3 Press p to enter USB break in 4 Press A or to select the desired option On Enable plug and play auto detection of USB devices Off Disable plug and play auto detection of USB devices 5 Press v to select Store go right and press to save setting 7 14 Select monitor out Select to output audio and video from TV via relevant AV connectors 1 Enter Setup menu 2 Press w to select Monitor out EN 21 Setup menu Monitor out Power on Low power standby Clock Auto scart USB break in Monitor out Blank current Channel Store go right 3 Press p to enter Monitor out 4 Press A or Ww to switch ON or OFF this feature 5 Press v to select Store go right and press gt to save setting 7 15 Select blank current channel Disable only the video display on screen Used on channels for radio transmission music etc 1 Enter Setup menu 2 Press w to select B
12. eration No respond from TV when using guest mode remote control This means that high security mode has been set to On Select Setup menu gt Remote control Set High security mode to Off BDS mode not working e Check that the mode is not switched on Switch the TV off and on to reset Remote control does not work e Check that the batteries are not faulty EN 24 Check that the remote control is not locked See Section 7 4 Select remote control setting for details 10 Index A AUDIO IN 6 UR 6 Auto scart 21 B BDS mode setup 16 Cc Channel install manually 19 switch on 19 Clock 7 display on 20 display standby 20 settings 20 time download 21 time offset 21 time setting 20 Clone configuration from Cloningto TV 23 From Cloning to TV 23 Common Interface Conditional Access Module 11 Connect 10 antenna cable 10 mains cord 10 EMF 2 EXT 1 6 EXT 2 6 EXT 3 6 G Get started 9 H HDMI 7 HDMI 1 6 HDMI 2 6 HDMI 3 6 Important information 4 K Kensington lock 9 M MHEG 13 Mute 13 Oo OSD display 18 Pay TV EN 25 setup 16 Power indicator low standby 20 on status 19 R Recycling 5 Remote control 8 basic use 8 batteries 10 locked 17 multi 18 overview 13 sensor setting 1 smart 18 S Safety 4 SCART 6 Screen care 5 SERV U 6 Setup menu 76 with guest mode remote control 16
13. erstanding the safety instructions in Section 1 1 consider the following before positioning your TV e The ideal viewing distance for watching TV is three times its screen size e Position the TV where light does not fall on the screen e Connect your devices before you position your TV e Your TV is equipped with a Kensington Security Slot at the back of the TV If connecting an anti theft Kensington lock not supplied position the TV within reach of a permanent object such as a table that can be easily attached to the lock 4 2 Wall mount the TV WARNING Wall mounting of the TV should only be performed by qualified installers Koninklijke Philips Electronics N V bears no responsibility for improper mounting that results in accident or injury Step 1 Purchase a VESA compatible wall bracket Depending on the size of your TV screen purchase one of the following wall brackets TV VESA compatible wall bracket type mm Special instructions screen size inches cm 22 56cm Adjustable None 100 x 100 26 66cm Adjustable None 100 x 200 32 81cm Adjustable 300 x 300 The VESA compatible bracket must be adjusted to 200 x 300 before securing to the TV 42 107cm Fixed 400 x 400 None or larger Step 2 Secure the VESA compatible wall bracket to the TV 1 Locate the four mounting nuts at the back of the TV
14. g do not remove the USB stick All remote control command and control buttons on the TV are disabled 6 Switch off and then on to reset the TV after cloning 8 2 From TV to Cloning Copy TV configuration data from TV to USB stick 1 Enter Setup menu 2 Press v to select TV to Cloning 3 Press p to enter TV to Cloning 4 Press p to load data to the USB stick B Setup menu TV to Cloning Clock Auto scart USB break in Monitor out Blank current Channel Store go right Cloning to TV TV to Cloning 6 Note During the process of copying do not remove the USB stick All remote control command and control buttons on the TV are disabled 5 Switch off and then on to reset the TV after cloning EN 23 9 Trouble shooting This section describes commonly encountered issues and accompanying solutions 9 1 Communication issues The TV does not communicate with external interactive terminal e Check that the card slot is enabled See Section 4 6 2 Access CAM services for details 9 2 Picture issues No picture e Check that the Blank current channel feature is not switched on See Section 7 16 Select blank current channel for details 9 3 Other issues The character F appears on the TV screen This means that the TV is currently in factory mode e Press and hold the MENU button at the side of the TV for a few seconds This will reset the TV to normal op
15. ked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on 4 Select Setup menu gt Remote control gt High security mode On Access the BDS Hotel Mode Setup Menu via the setup remote control only Off Access the BDS Hotel Mode Setup Menu via the setup remote control or guest mode remote control 7 2 1 Enter Setup menu Switch on BDS mode 2 Press p to enter BDS mode 3 Press A to select On The user menus blocked and all settings of the BDS mode setup menu are in effect To operate the TV as a normal consumer TV select Off Setup menu BDS mode BDS mode Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on 4 Press w to select Store go right and press gt to save setting 7 3 Locklocal keyboard 1 Enter Setup menu Press w to select Local keyboard locked 2 3 Press to enter Local keyboard locked 4 Press A to select On The VOLUME PROGRAM and MENU buttons on the TV control are locked To unlock select Off Setup menu BDS mode Local keyboard locked Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on 5 Press v to select Store go right and press gt to save setting 7 4 Select remote control setting 1 Enter Setup menu 2 P
16. lank current Channel N Setup menu Blank current Channel Low power standby Clock Auto scart USB break in Monitor out Blank current Channel Store go right Cloning to TV 3 Press to enter Blank current Channel 4 Press A or v to switch ON or OFF this feature 5 Press v to select Store go right and press gt to save setting 7 16 Save settings Select this option to save the settings EN 22 1 Select your desired options or adjustments 2 Press v to select Store go right Setup menu Clock Auto scart USB break in Monitor out Store go right Blank current Channel Store go right Cloning toTV TV to Cloning 3 Press p to enter Store go right 4 Press to confirm saving Tip You can save once after you have selected all the settings but before you exit the menu 8 Clone configuration 8 1 From Cloning to TV Copy TV configuration data from a USB stick to TV 1 Insert the USB stick to the USB connector at the side of the TV Enter Setup menu Press w to select Cloning to TV Press p to enter Cloning to TV Oi WN Press p to load data to the TV During this process the cloning files Setup menu Clock Auto scart USB break in Monitor out Cloning to TV Blank current Channel Store go right Cloning to TV TV to Cloning Note e During the process of copyin
17. marks of ACCO World Corporation with issued registrations and pending applications in other countries throughout the world All other registered and unregistered trademarks are the property of their respective owners EN 3 1 Important Read and understand all instructions before you use the TV If damage is caused by failure to follow instructions the warranty does not apply 1 1 Safety e Risk of electric shock or fire EN 4 Never expose the TV to rain or water Never place liquid containers such as vases near the TV If liquids are spilt on or into the TV disconnect the TV from the power outlet immediately Contact Philips to have the TV checked before use Never place the TV remote control or batteries near naked flames or other heat sources including direct sunlight To prevent the spread of fire keep candles or other flames away from this product at all times Never insert objects into the ventilation slots or other openings on the TV When the TV is swivelled ensure that no strain is exerted on the power cord Strain on the power cord can loosen connections and cause arcing Risk of short circuit or fire Never expose the remote control or batteries to rain water or excessive heat Avoid force coming on the power plugs Power plugs that are partly loosened can cause arcing or fire Risk of injury or damage to the TV e Two people are required to lift and carry a TV that weighs m
18. models with clock display OK Activates a setting Navigation keys Up a Down y Left and Right gt keys navigate the menu SLEEP Sets sleep timer P Switches to the next or previous channel Number buttons Selects a channel page or setting T Selects a picture format MHEG CANCEL Cancels digital text or interactive services UK only BK Mutes or restores sound A l Increases or decreases volume MENU Toggles the menu on or off ALARM ON Activates the alarm function Only for models with clock display EN 13 18 TELETEXT Toggles teletext on or off 19 Spilts the current channel or source on the left of the screen Teletext appears on the right EN 14 6 First time setup The first time the TV is switched on a language selection menu appears PHILIPS TVinstallation Press OK or the green colour key on your remote control to continue Select your language and follow the on screen instructions to setup the TV Tip You can skip the first time setup procedures by pressing MENU on the TV s control twice EN 15 7 Setup BDS mode The TV is designed to operate as BDS Hotel Mode which offers the following benefits Disable user menu Guests cannot change channel picture and sound settings Select a switch on volume and channel The TV will always start on the specified channel and volume level Set a maximum volume Setup Menu via the setup remote co
19. ntrol or guest mode remote control Blank out certain programmes Disable the VOLUME PROGRAM and MENU buttons on the TV Suppress screen information Note For BDS mode settings to take effect turn the TV set off then on again Tip To enter menu level press To leave menu level press lt 7 1 Access setup menu 7 1 1 With guest mode remote control 19 Cel J GJ eer GCI Goi MHEG oe II L we Co J Switch on the TV and select a TV channel 2 Press 3 1 9 7 5 3 and Kon the remote control within 20 seconds to display the Setup menu EN 16 Mo i 5 Setup menu BDS mode Local keyboard locked Remote control OSD display Switch on volume 50 BDS mode Maximum volume 100 Switch on channel Power on 3 Select Setup menu gt Remote control gt High security mode On Allows access to the BDS Hotel Mode Setup Menu via the setup remote control only Off Allows access to the BDS Hotel Mode Setup Menu via the setup remote control or guest mode remote control 7 1 2 With setup remote control Ol TEXT SMART oo 8 0000 0 1 Switch on the TV and select a TV channel 2 Slide the slider at the side of the remote control to SETUP 3 Press M to display the Setup menu BDS mode Setup menu BDS mode Local keyboard loc
20. o save setting 7 7 Set maximum volume The TV volume will not exceed the selected volume level set 1 Enter Setup menu 2 Press w to select Maximum volume 3 Press gt to enter Maximum volume Setup menu Maximum volume BDS mode Local keyboard locked Remote control OSD display Switch on volume 50 gt Maximum volume Switch on channel Power on lt gt Press A or v to select the desired volume level 5 Press w to select Store go right and press gt to save setting 7 8 Select switch on channel When the user switches the TV on it will tune to the specified channel 1 Enter Setup menu 2 Press w to select Switch on channel Switch on channel 1 Digital 5 Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on 3 Press p to enter Switch on channel 4 Press A or w to select the desired channel 5 Press v to select Store go right and press gt to save setting 7 9 Set power on status When the user switches the TV on it will enter the specified mode of operation selected 1 Enter Setup menu 2 Press w to select Power on EN 19 Power on Setup menu Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on Low power standby Press gt to enter Power on P
21. ore than 55 Ibs e If you stand mount the TV use only the supplied stand Secure the stand to the TV tightly Place the TV on a flat level surface that can support the weight of the TV and stand e The TV must be mounted on the wall bracket designed for this TV and on a wall that can safely hold the weight of the TV Koninklijke Philips Electronics N V bears no responsibility for improper wall mounting that results in accident or injury Risk of injury to children Follow these precautions to prevent the TV from toppling over and causing injury to children e Never place the TV on a surface covered by a cloth or other material that can be pulled away e Ensure that no part of the TV hangs over the edge of the mounting surface e Never place the TV on tall furniture such as a bookcase without anchoring both the furniture and TV to a suitable support such as a concrete wall e Educate children about the dangers of climbing on furniture to reach the TV Risk of overheating Never install the TV in a confined space such as a bookcase Always leave a space of at least four inches around the TV for ventilation Ensure curtains or other objects never cover the ventilation slots on the TV Risk of injury fire or power cord damage Never place the TV or any objects on the power cord Disconnect the TV from the power outlet and antenna before lightning storms During lightning storms never touch any part of the TV po
22. ress A or W to select the desired status On The TV will always turn on after the mains power is connected Standby The TV will always turn to standby after the mains power is connected Last status The TV will always turn on the last power status after the mains power is connected Press v to select Store go right and press gt to save setting 7 10 Set low power standby Set the different power saving option when the TV is in standby mode Enter Setup menu 2 Press v to select Low power standby D Setup menu Low power standby Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on Low power standby Clock 3 Press p to enter Low power standby 4 Press A or v to select the desired status EN 20 Green The TV will enter a low standby mode to achieve minimum power consumption e Fast The TV will enter a semi standby mode to achieve fast power up 5 Press v to select Store go right and press to save setting 7 11 Select clock settings Select and configure the clock settings 1 Enter Setup menu 2 Press w to select Clock Setup menu Switch on volume 50 Maximum volume 100 Switch on channel Power on Low power standby Clock Auto scart USB break in 3 Press p to enter Clock 4 Press A or v to select the setting that you want to configure Press p to select the settings
23. ress w to select Remote control J Remote control ES Setup menu BDS mode Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on Press gt to enter Remote control Press A or to select a setting EE a Press gt to enter Remote control locked On Locks standard remote control buttons EN 17 Off Unlock remote control buttons e Multi remote control Off Disable multi remote control function e Blue Select to use the blue guest remote control e Red Select to use the red guest remote control Green Select to use the green guest remote control Yellow Select to use the yellow guest remote control Smart RC On Select to use the smart remote control Off Disable the use the smart remote control e Pay TV setup Select RO R1 or R2 setting for the various pay TV channels e High security mode On Access the BDS Hotel Mode Setup Menu via the setup remote control only Off Access the BDS Hotel Mode Setup Menu via the setup remote control or guest mode remote control 7 5 Select OSD display 1 Enter Setup menu 2 Press w to select OSD display EN 18 oy Ow Setup menu BDS mode Local keyboard locked Remote control OSD display Switch on volume 50 OSD display Maximum volume 100 Switch on channel Power on Press
24. the power cord always pull the plug never the cable To connect the mains cord Note The location of the mains connector varies according to TV model EN 10 4 5 Insert the remote control batteries 1 Slide the battery cover off the back of the remote control 2 Insert the two supplied batteries Size AAA Type LRO3 Be sure the and ends of the batteries line up with the markings inside the case 3 Slide the cover back into position 6 Note Remove the batteries if not using the remote control for an extended period of time 4 6 Prepare TV for digital services Scrambled digital TV channels can be decoded with a Conditional Access Module inserted with a smart card CAM provided by a digital TV service operator The CAM may enable several digital services depending on the operator and services you choose for example pay TV Contact your digital TV service operator for more information about services and terms 4 6 1 Using the Conditional Access Module A WARNING Switch off your TV before inserting a CAM Be sure to follow the instructions described below Wrong insertion of a CAM may damage both the CAM and your TV 1 Following the directions printed on the CAM gently insert the CAM into the Common Interface slot on the side of the TV a N A 2 Push the CAM in as far as it will go
25. ual or any adjustments and assembly procedures not recommended or authorised in this manual shall void the warranty Open source software This television contains open source software Philips GBU Hospitality hereby offers to deliver or make available upon request for a charge no more than the cost of physically EN 2 performing source distribution a complete machine readable copy of the corresponding source code on a medium customarily used for software interchange To obtain the source code write to Philips Singapore Pte Ltd Philips GBU Hospitality Software Development Manager 620A Lorong 1 Toa Payoh Singapore 319762 This offer is valid for a period of 3 years after the date of purchase of this product Pixel characteristics This LCD product has a high number of color pixels Although it has effective pixels of 99 999 or more black dots or bright points of light red green or blue may appear constantly on the screen This is a structural property of the display within common industry standards and is not a malfunction Compliance with EMF Koninklijke Philips Electronics N V manufactures and sells many products targeted at consumers which like any electronic apparatus in general have the ability to emit and receive electromagnetic signals One of Philips leading Business Principles is to take all necessary health and safety measures for our products to comply with all applicable
26. wer cord or antenna cable Risk of hearing damage Avoid using earphones or headphones at high volumes or for prolonged periods of time Never allow children to climb on or play with the TV Place the TV where it cannot be pushed pulled over or knocked down If the TV is transported in temperatures below 5 C Remove the TV from the box Wait until the TV temperature matches the room temperature Install the TV 2 Screen care Avoid stationary images as much as possible Stationary images are images that remain on screen for extended periods of time Examples include on screen menus teletext pages black bars stock market information TV channel logos and time displays If you must use stationary images reduce screen contrast and brightness to avoid screen damage Unplug the TV before cleaning Clean the TV and frame with a soft damp cloth Never use substances such as alcohol chemicals or household cleaners on the TV Risk of damage to the TV screen Never touch push rub or strike the screen with any object To avoid deformations and colour fading wipe off water drops as soon as possible 3 Recycling This product is designed and manufactured with high quality materials and components which can be recycled and reused This product is designed and manufactured for material recycling When you see the crossed out wheel bin symbol attached to a product it means the product is covered by
Download Pdf Manuals
Related Search