Sigma SC-SAE412-S3
Contents
1. software automatically Recommended then click Next Note Most systems will install the driver automatically after inserting driver CD Click Finish remove the driver CD and restart Windows to complete the installation To Verify Windows 2000 XP Server 2003 Installation 1 2 os Right click My Computer and click Manage Select Device Manager Double click SCSI and RAID Controllers then double click Silicon Image Sil 3132 Controller to display driver properties A message This device is working properly is displayed in the dialog box the driver has been correctly installed 32 bit Windows Vista New 32 bit Windows Vista Installation 1 Install the board and follow Microsoft procedures to install Windows accordingly At Where do you want to install Windows click Load Driver Insert driver CD then click Browse Double click CD Drive D change D to match your CD ROM drive letter Highlight Floppy folder then click OK Select Silicon Image Sil 3132 Controller D Floppy SI3132 inf then click Next Follow on screen instructions to complete Windows Vista installation Existing 32 bit Windows Vista Installation 1 Install the board and boot up Windows 2 At the Found New Hardware Wizard insert the driver CD select Locate and install driver software Recommended then click Continue 3 Click Next then Close 4 Remove the driver CD and restart Windows to complet2. O COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SHG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA SATAIIPCle Proisa trademark of SHG Inc SIIG and the SHG logo are registered trademarks of SHUG Inc Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Mac and Mac OS are registered trademarks of Apple Computer Inc Othernames usedin this publication are for identification only and may be trademarks of their respective companies December 2007 Copyright 2007 by SIIG Inc All rights reserved
3. XP w SP2 or later Server 2003 w SP1 or later select No not this time then click Next Note Most systems will install the driver automatically after inserting driver CD Insert driver CD select Install the software automatically Recommended then click Next Click Next then click Finish Restart Windows tocomplete the driver installation 64 bit Windows XP Server 2003 New 64 bit Windows XP Server 2003 Installation A new installation of Windows XP Server 2003 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 64bit folder found on the driver CD ontoa blank floppy disk then follow the directions below 1 Install the board and follow Microsoft procedures to install Windows accordingly Restart your system when prompted during Windows installation At the Windows Setup screen press F6 to continue Insert the driver diskette Press S then press Enter Select Silicon Image SiI 3132 Controller 64 bit Extended and press Enter Press Enter to continue and follow on screen instructions to complete the installation Existing 64 bit Windows XP Server 2003 Installation 1 2 Install the board and boot up Windows At the Found New Hardware Wizard XP w SP1 or earlier Server 2003 continue to step 3 XP w SP2 or later Server 2003 w SP1 or later select No not this time then click Next Insert the driver CD select Install the
4. Z SATA Il PCle Pro J Quick Installation Guide Introducing the SATA II PCle Pro The SATA II PCIe Pro is an ultra high speed dual channel Serial ATA Generation 2 controller for usein PCI Express enabled system Features and Benefits e Compliant with PCI Express Base Specification 1 0a e Compliantwith Serial 1 0a specification withsupport for full complement of SATA II optional features e PCTExpress 1 lane x1 SATA II adapter works with PCI Express slots with different lane width e Installsinany available PCI Express slot and support data transfer rates up to 3 0Gbps 300MBps e Supports Native Command Queuing NCQ Non zero offsets NCQ and Out of order date delivery NCQ System Requirements PC e PCI Express enabled system with an available PCI Express slot e Windows 2000 XP 32 64 bit Server 2003 32 64 bit Vista 32 64 bit Mac e PCI Express enabled system with an available PCI Express slot Mac OS 10 4 or later 04 0397B 1 Package Contents e SATA II PCIe Pro adapter e Driver CD e Quick Installation Guide Board Layout HDD LED pins Front chassis LED connects horizontally External _ connectors HDD Activity LED Figure 1 SATA II PCIe Pro Board Layout Hardware Installation General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further inform
5. ation if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Turn OFF the power to your computer Unplug the power cord and remove your computer s cover Remove the slot bracket from an available PCle slot Carefully align the card to the selected PCIe slot push the board down firmly but gently until it is well seated Replace the slot bracket holding screw to secure the card Replace the computer cover and reconnect the power cord Windows Driver Installation This section provides information on how to install the SATA II PCle Pro drivers Windows 2000 New Windows 2000 Installation A new installation of Windows 2000 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the Floppy folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow Microsoft procedures to install Windows 2000 accordingly Restart your system when prompted during Windows installation At the Windows 2000 Setup screen press F6 to install the driver Insert the driver diskette Press S then press Enter Select Silicon Image Sil 3132 Controller for Windows 2000 and press Enter 6 Press Enter to continue and foll
6. ds 4 A pcil095 3132 should be displayed Hot Plugging Hard Disk Drives To remove a drive from a powered up system do the following 1 Click and drag icon into the Trash 2 Youcan now remove the target disk 10 Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analysts will promptly respond SIIG offers a lifetime manufacturer warranty with this product Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then RMA to submit a request to SIG RMA If the product is determined to be defective an RMA number willbe issued SIIG RMA department can also be reached at 510 413 5333 Step 2 After obtaining an RMA number ship the product Properly pack the product for shipping All software cable s and any other accessories that came with the
7. e the installation 64 bit Windows Vista New 64 bit Windows Vista Installation 1 Install the board and follow Microsoft procedures to install Windows accordingly 2 At Where do you want to install Windows click Load Driver 3 Insert driver CD then click Browse Double click CD Drive D change D to match your CD ROM drive letter Double click 64bit folder highlight AMD64 then click OK Select Silicon Image Sil 3132 Controller D 64bit AMD64 SI3132 inf then click Next Follow on screen instructions to complete Windows Vista installation Existing 64 bit Windows Vista Installation 1 2 Install the board and boot up Windows At the Found New Hardware Wizard insert the driver CD select Locate and install driver software Recommended then click Continue Click Next then Close Remove the driver CD and restart Windows to complete the installation To Verify Windows Vista Installation 1 2 3 Rightclick Computer click Manage click Continue Select Device Manager Double click Storage controllers then double click Silicon Image Si13132 Controller to display driver properties A message This device is working properly is displayed in the dialog box the driver has been correctly installed BIOS Configuration The SATA II PCIe BIOS will appear everytime your system starts up If the bios doesn t show please try your controllerin another PCle slot During this Post process the bios
8. original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in1985 SHG Inc isa leading computer upgrade manufacturer ofI O connectivity products including PCI amp ISA serial and parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b networking sound cards and other accessories SIIG is the premier one stop source of upgrades SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and throughe commerce sites PRODUCT NAME SATA II PCle Pro FCC RULES TESTED T
9. ow on screen instructions to complete the installation Existing Windows 2000 Installation 1 Install the board and boot up Windows 2000 2 At the Found New Hardware Wizard click Next 3 Select Search for a suitable driver for my device recommended and click Next 4 InsertthedriverCD check CD ROM drives uncheck the other boxes and click Next Click Next again to continue 5 Click Finish and restart Windows to complete the driver installation 32 bit Windows XP Server 2003 New 32 bit Windows XP Server 2003 Installation A new installation of Windows XP Server 2003 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the Floppy folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow Microsoft procedures to install Windows accordingly 2 Restart your system when prompted by Windows installation 3 Atthe Windows Setup screen press F6 to install the driver 4 Insert the driver diskette Press S then press Enter 5 Select Silicon Image Sil 3132 Controller for Windows XP and Server 2003 and press Enter 6 Press Enter to continue and follow on screen instructions to complete Windows installation Existing 32 bit Windows XP Server 2003 Installation 1 a 4 5 Install the board and boot up Windows At the Found New Hardware Wizard XP w SP1 or earlier Server 2003 continue to step 3
10. will show up and indicate the devices attached to it External Device Connection External Serial ATA devices should come with their own accessories In most cases you just need to power up the external device and connect it to the external port For more information please refer to the external device s manual Hot Plugging Hard Disk Drives To remove a drive from a powered up system do the following 1 Right click My Computer and click Manage 2 For Windows Vista click Continue If not please continue on step 3 3 Select Device Manager 4 Click Disk Drives right click the target disk and select Disable Enable 5 You can now remove the target disk Mac OS Driver Installation This section provides information on how to install the SATA II PCle Pro drivers 1 Install the SATA IJ PCle Pro and boot up your system 2 InsertdriverCD Atthe desktop double click Drivers icon 3 Double click Mac folder 4 Double click il3132_1 1 9u_S 1_Pkg pkg 5 Click Continue Continue Continue then Agree 6 In OS 10 5 click Change Install Location If not please continue with step 7 7 Select destination drive then click Continue then click Install 8 AtAuthenticate enter password if there s any then OK 9 Click Close and restart system to complete the installation To Verify Mac Installation 1 At the Desktop click Go then click Utilities 2 Double click System Profiler 3 Click PCI Car
Download Pdf Manuals
Related Search