Trendnet 300Mbps Wireless N Hot Spot Access Point
Contents
1. TRENDnet Quick Installation Guide Ss A LA Poi A TEW 636APB H W V1 0R Table of Contents E O O Li 1 1 Before YOU Start oo cic cccesccssseccsseecsesesensesenseessresenreseneessneseneeennens 1 2 Hardware Installation c cccccccccccsssssscsssscsscssescscssesecsessesscassesecaveseeneaven 2 3 Configure the Access Point csecsen 3 A A 6 Version 03 24 2008 7 1 Before You Start Package Contents e TEW 636APB e User s Guide CD ROM e Quick Installation Guide e AC Power Adapter 12V DC 1A e 1 RJ 45 cable Installation Requirements Web Browser Internet Explorer 5 5 or higher e A computer with a network adapter or wireless adapter properly installed e A network Switch or Hub with an available network LAN port e ARJ 45 network cable e TEW 621PC version 2 or TEW 623PI version 2 Optional Application 300Mbps Wireless N HotSpot Access Point P a e Notebook with 300Mbps Wireless N PC Card Workstation with 300Mbps TEW 621PC Wireless N PCI Adapter TEW 623PI E Internet gt Y Cable DSL 4 Port Gigabit Firewall Router Workstation with 300Mbps Modem TWG BRF114 Wireless N USB Adapter TEW 624UB Ml 300Mb Rumi 10 100Mbps 2 Hardware Installation Note Locate an optimum location for the Access Point The best place for the Access Point is usually at the center of your wireless network Please connect the computer configuring the TEW 636APB2. on to the access point configuration page from a wired computer Click Wireless gt Virtual AP Click on the desired Virtual AP and then click Configure If you still encounter problems or have any questions regarding the TEW 636APB please contact TRENDnet s Technical Support Department Certifications This equipment has been tested and found to comply with FCC and CE Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received Including interference that may cause undesired operation Waste electrical and electronic products must not FC T be disposed of with household waste Please recycle where facilities exist Check with you Local Authority or Retailer for recycling advice n NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT ADVERTENCIA En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentac n necesario para su funcionamiento El uso de un adaptador distinto al mencionado puede producir da os fisicos y o da os al equipo conectado El adaptador de alimentaci n debe operar con voltaje y frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalaci n TRENDNET Customer S
3. to the same switch hub 1 Connect a RJ 45 cable from the Switch Hub to the LAN port of the Access Point 2 Connect the AC Power Adapter to the Access Point and then to a power outlet 3 Verify that the following panel lights are on Power and WLAN E 3 Configure the Access Point Note It is recommended that you configure the Access Point from a wired computer 1 Open your web browser type http SCXXXXXX in the Address bar and then press Enter XXXXXX represents the last 6 F about blank Microsott Intermezi Explorer Ele Edt sem Fakes Too Halo Qee x El e ya Seno Str Faros sid hips oona digits of the Mac Address You can find the Mac Address on the bottom of the router Connect to scxooona 2 Enter the User name and Password and then click OK User Name admin o Password password 5 3 Click System and then click Basic Settings Select your country or domain from the drop down menu click Fixed IP Address and type in an IP address Subnet Mask Gateway and DNS to match your current network settings Click Save q Ga map n S TRENDNET Wireless N Hotapet Ascess Paini CS 4 Click Wireless and then click re Basic Settings Select the desired Wireless Mode select Access Point for Operating mode and then click Save Virtual AP Satiinga ar a WAF heen FLED eva 5 Click Virtual APs Select a Virtual AP click Enab
4. le and then click Configure a A Be pd er Note The example below is for WPA PSK security If your wireless adapters do not support WPA PSK then select WEP TRENDNET Wireless M Mot Spot cosa Poi 6 Enter a SSID select the desired E Security System enter the Network Key click Save and then click Back Ron Brita D gnp Kop piaia Piy Libri a pelada Dmg ri see ar dde rm 7 Repeat step 5 and 6 for each subsequent Virtual AP 8 Click Management and then click Admin Login Wiroless N HotSpot Access Point TEW GIEAPS 9 If desired enter a new user name Sa check Change Admin Password enter a new password retype the new password and then click Save By default Admin Connections Enable HTTP Admin conmections HTTP Pert Number 0 O Enable HTTPS secure HTTP Admin connections User Name admin Password password 2 TRENDNET 10 Click Apply and then click A Reboot Note If you skip this step any settings that you changed will NOT be saved Your installation is now complete For detailed information regarding the TEW 636APB s configuration and advanced settings please refer to the User s Guide included on the Driver CD ROM or TRENDnet s website at www trendnet com Register Your Product To ensure the highest level of customer service and support please take a moment to register your product Onli
5. ne at www trendnet com register Thank you for choosing TRENDnet Troubleshooting E Q1 I typed http SCXXXXXX in my Internet Browser s Address Bar but an error message says The page cannot be displayed How can get into the TEW 636APB s web configuration page A1 First check your hardware settings again by following the instructions in section 2 Second make sure the LAN and WLAN lights are lit Third verify the Mac Address of the access point Look at the bottom of the access point Copy the last six digits of the Mac Address Then open up your browser and type in http SCXXXXXX XXXXXX represents the last six digits of the Mac Address and then Enter Fourth perform a factory reset Take a pin or paperclip press on the reset button for 15 seconds and then let go Q2 All the settings are correct but can not make a wireless connection to the Access Point A2 First double check that the WLAN light on the Access Point is lit Second power cycle the Access Point Unplug the power to the Access Point Wait 15 seconds then plug the power back in Third contact the manufacturer of your wireless network adapter Make sure the wireless network adapter is configured with the proper SSID The default SSID of the Access Point is wireless 0 If you have enabled any encryption on the Access Point make sure to configure the wireless network adapter with the same Pre shared key If you do not remember the encryption key log
6. upport Visit www trendnet com support Email support trendnet com Europe Germany France Italy Spain Switzerland UK Toll Free Telephone 00800 60 76 76 67 English Espanol 24 7 Worldwide Telephone 31 0 20 504 05 35 English Espanol 24 7 Product Warranty Registration Please take a moment to register your product online Go to TRENDnet s website at http www trendnet com register TRENDNET 20675 Manhattan Place Torrance CA 90501 USA Copyright 2008 All Rights Reserved TRENDnet
Download Pdf Manuals
Related Search