DeLonghi ESAM 4200.S
Contents
1. ssss 14 Cleaning the coffee spouts 14 Cleaning the pre ground coffee funnel 14 Cleaning the infuser sss 14 DESCALING iion neReee 15 SETTING WATER HARDNESS 16 Measuring water hardness Set water hardness sssseses TECHNICAL SPECIFICATION 16 DISPOSAL aeo iaaea 16 MEANING OF LIGHTS DURING NORMAL OPERATION n 17 MEANING OF THE ALARM LIGHTS 18 TROUBLESHOOTING 19 INTRODUCTION SAFETY Thank you for choosing the ESAM4 automatic coffee and cappuccino maker We hope you enjoy using your new appliance Take a few minutes to read these instructions This will avoid all risks and damage to the ma chine Symbols used in these instructions Important warnings are identified by these symbols These warnings must absolutely be respected A Danger Failure to observe the warning could result in possibly life threatening injury from electric shock A Important Failure to observe the warning could result in in jury or damage to the appliance A Danger of burns Failure to observe the warning could result in scalds or burns g Please note This symbol identifies important advice or infor mation for the user Letters in brackets The letters in brackets refer to the legend in the Description of the appl2. The appliance does not come on e Itis not plugged into the mains socket e Plug into the mains socket e The main switch A2 is not turned on e Place the main switch in the position fig 3 When the steam hot water knob is turned to the position steam hot water is not delive red from the cappucci no maker e The holes in the cappuccino maker and or steam nozzle are blocked e Clean the cappuccino maker as described in the section Cleaning the cappuccino maker after use The infuser assembly cannot be removed for cleaning e The appliance is on or has not completed the turning off cycle e The infuser can only be removed when the appliance has been turned off correctly see the section Turning off 20
3. or C7 WD light stays on until delivery is complete i Please note While the machine is making coffee delivery can be interrupted at any moment by pres sing one of the two coffee buttons S or KZ XZ e Atthe end of delivery to increase the quantity of coffee in the cup just press within 3 secon ds one of the coffee buttons CZ or CZ KZ Once the coffee has been made the appliance is ready to use again i Please note For hotter coffee see the section Tips for a hot ter coffee page 11 A Important e Ifthe coffee is delivered a drop at a time too weak and not creamy enough or too cold read the tips in the Troubleshooting sec tion on page 19 e Lights may be displayed on the control pa nel during use Their meaning is given in the section Meaning of Ights on page 17 Making coffee using pre ground coffee A Important Never add pre ground coffee when the ma chine is off or it could spread through the inside of the machine and dirty it This could damage the appliance e Never use more than one level measure or it could dirty the inside of the machine or block the funnel g Please note If you use pre ground coffee you can only make one cup of coffee at a time 1 Turn the coffee taste selection knob anticlockwise as far as it will go to the position 2 Make sure the funnel is not blocked then add one level measure of pre ground coffee fig 13 3 Place a
4. Cleaning the infu S ser The inside of the appliance Clean the appliance thoroughly is very dirty The light flashes The service door is open If you cannot close the door make 10 e O O sure the infuser is correctly inser EN ts A ted D o Z m The lights flash alternately The coffee maker has been switched on with the steam knob in the open position Turn the steam knob clockwise un til delivery stops Below is a list of some of the possible malfunctions If the problem cannot be resolved as described contact Customer Services PROBLEM POSSIBLE CAUSE SOLUTION The coffee is not hot The cups were not preheated Warm the cups by rinsing them with hot water N B you can use the hot water function The infuser has cooled down because 2 3 minutes have elapsed since the last coffee was made Before making coffee heat the infuser by pressing the button The coffee is weak or not creamy enough The coffee is ground too coarsely Turn the grinding adjustment knob one click anticlockwise towards 1 while the coffee mill is in operation fig 7 Continue one click at a time until coffee delivery is satisfactory The effect is only visible after delivering 2 coffees see the section Adjusting the coffee mill on page 11 The coffee is unsuitable Use pre ground coffee for espresso coffee makers The coffee is delivered
5. Please note e When using the appliance for the first time you need to make 4 5 cups of coffee or 4 5 cappuccinos before the appliance starts to give satisfactory results TURNING THE APPLIANCE ON i Please note Before turning the appliance on make sure the main switch on the back of the appliance is in the l position fig 3 Each time the appliance is turned on it performs an automatic preheat and rinse cycle which can not be interrupted The appliance is ready for use only after comple tion of this cycle N Danger of burns During rinsing a little hot water comes out of the coffee spouts and is collected in the drip tray un derneath Avoid contact with splashes of water e To turn the appliance on press the D but ton fig 4 The and CP lights flash while the appliance is heating up and perfor ming an automatic rinse cycle By circulating the hot water the appliance heats both the boiler and the internal circuits During this phase the light flashes When the and S7 lights remain on ste adily the appliance is at temperature TURNING THE APPLIANCE OFF Each time the appliance is turned off it performs an automatic rinse cycle which cannot be inter rupted A Danger of burns During rinsing a little hot water flows from the coffee spouts Avoid contact with splashes of water To turn the appliance off press the d button fig 4 The appliance performs a rinse
6. cup under the coffee spouts 4 Press the X cup coffee button fig 11 5 Preparation begins and can be interrupted at any moment by pressing one of the two coffee buttons Cv oro 7 To deactivate the pre ground coffee function turn the knob to one of the other positions g Please note A few seconds may elapse between energy sa ving mode and delivery of the first coffee MAKING CAPPUCCINO A Important Danger of burns During preparation steam is given off Take care to avoid scalds 1 When preparing cappuccino make the cof fee in a large cup 2 Filla container with about 100 grams of milk for each cappuccino to be made In choosing the size of the container bear in mind that the milk doubles or triples in volu me g Please note For a richer denser froth use skimmed or partially skimmed milk at refrigerator tempe rature about 5 C To avoid milk with poor froth or large bub bles always clean the cappuccino maker as described in the section Cleaning the cap puccino maker after use 3 Press the button The corresponding light flashes indicating that the appliance is heating up 5 Turn the cappuccino maker outwards and immerse in the milk container fig 14 6 When the light stops flashing and co mes on steadily turn the steam knob to the position Steam is delivered from the cappuc cino maker giving the milk a creamy frothy appearance and making it more voluminous 7 F
7. CONTENTS INTRODUCTION 7 Symbols used in these instructions 7 Letters in brackets s sss 7 Troubleshooting and repairs 7 didum c 7 Fundamental safety warnings 7 DESIGNATED USE 8 INSTRUCTIONS 8 DESCRIPTION Description of the appliance Description of control panel PRELIMINARY CHECKS Checking the appliance Installing the appliance Connecting the appliance Using the appliance for the first time 9 TURNING THE APPLIANCE ON 9 TURNING THE APPLIANCE OFF 10 SETTING AUTO OFF STAND BY 10 ENERGY SAVING 10 MAKING COFFEE 10 Selecting the coffee taste 10 Selecting the quantity of coffee in the cup 11 MAKING CAPPUCCINO 12 Cleaning the cappuccino maker after use 13 HEATING WATER 13 CLEANING e eroe xxn 13 Cleaning the coffee maker 13 Cleaning the coffee grounds container 13 Cleaning the drip tray 14 Cleaning the inside of the machine 14 Cleaning the water tank
8. ble for damage deriving from failure to respect these in structions i Please note Keep these instructions If the appliance is passed to other persons they must also be provided with these instructions DESCRIPTION miei of the appliance page 3 A A1 Grinding adjustment knob A2 Main switch on back of appliance A3 Beans container A4 Beans container lid A5 Pre ground coffee funnel lid A6 Compartment for measure A7 Cup shelf A8 Pre ground coffee funnel A9 Steam spout A10 Cappuccino maker removable A11 Steam nozzle removable A12 Water tank A13 Power cable A14 Cup tray A15 Drip tray A16 Infuser door A17 Coffee grounds container A18 Coffee spout adjustable height A19 Coffee guide A20 Infuser A21 Control panel Description of control panel page 3 B B1 d button turns the appliance on and off stand by B2 1 cup and coffee temperature OK light B3 V button to make 1 cup of coffee B4 2cups and coffee temperature OK light B5 PT button to make 2 cups of coffee B6 Steam and steam temperature OK light B7 button to select the steam function B8 Coffee quantity selection knob short stan dard or long B9 Selection knob to choose coffee taste for a mild standard or strong coffee or use pre ground coffee amp B10 Steam hot water knob B11 light no water or water tank absent B12 lj light grounds container full or absent B13 Alight genera
9. by turning the steam knob to the 0 po sition Please note If Energy Saving mode is active you may have to wait a few seconds before the hot water is delivered To produce steam immediately after prepa ring hot water you should open the steam knob for a few seconds to empty the water circuits LEANIN Cleaning the coffee maker The following parts of the machine must be cle aned regularly coffee grounds container A17 drip tray A15 water tank A12 Coffee spouts A18 pre ground coffee funnel A8 inside of the machine accessible after ope ning the infuser door A16 infuser A20 A Important Do not use solvents abrasive detergents or alcohol to clean the coffee maker With De Longhi superautomatic coffee ma kers you need not use chemical products to clean the machine The descaler recommen ded by De Longhi is made from natural and completely biodegradable substances e None of the components can be washed in a dishwasher e Do not use metal objects to remove encru stations or coffee deposits as they could scratch metal or plastic surfaces Cleaning the coffee grounds container When the ts light flashes the coffee grounds container needs emptying Unless you clean the grounds container the light will continue to flash and the appliance cannot be used to make coffee To clean with the machine on e Open the service door on the front of the ap plianc
10. cycle then goes off g Please note If the appliance is not used for an extended pe riod place the main switch in the 0 position fig A Important To avoid damaging the appliance never place the main switch fig 6 in the 0 position while the appliance is on SETTING AUTO OFF The appliance is set by default to go off if not used for two hours The time can be changed so that the appliance switches off after 15 or 30 minutes or after 1 2 or 3 hours 1 With the appliance off but the main switch in the position fig 3 press and hold the ECO button until the lights at the bottom of the control panel come on see image after point 2 2 Select the required period of time 15 or 30 minutes or 1 2 or 3 hours by pressing the dh button see the light time table below 15min 30min 1h ts A E eco 3 Press the ECO button to confirm the selec tion Auto off is programmed Ci Please note To disconnect the appliance completely place the main switch at the back of the appliance in the 0 position fig 6 ENERGY SAVING Use this function to activate or deactivate energy saving mode This reduces energy consumption in compliance with current European regula tions ECO mode is active by default ECO light on To deactivate the function press the ECO button The light goes off To reactivate the function press the ECO button again the light comes on i Please note A few s
11. e extract the drip tray fig 18 empty and clean e Empty the grounds container and clean tho roughly to remove all residues left on the bottom A Important When removing the drip tray the grounds con tainer must be emptied even if it contains few grounds If this is not done when you make the next cof fees the grounds container may fill up more than expected and clog the machine Cleaning the drip tray A Important If the drip tray is not emptied regularly the water could overflow from the edge and seep inside or around the machine This could damage the machine the surface it rests on or the surrounding area The drip tray is fitted with a level indicator red showing the level of water it contains fig 19 Before the indicator protrudes from the cup tray the drip tray must be emptied and cleaned To remove the drip tray 1 Remove the drip tray and the grounds con tainer fig 18 2 Empty the drip tray and grounds container and wash them 3 Replace the drip tray and grounds container Cleaning the inside of the machine A Danger of electric shock Before cleaning internal parts the machine must be turned off see Turning off and unplugged from the mains power supply Never immerse the coffee maker in water 1 Check regularly about once a month that the inside of the appliance accessible after removing the drip tray is not dirty If neces sary remove coffee deposits wi
12. econds may elapse between energy sa ving mode and delivery of the first coffee as the appliance must heat up again MAKING COFFEE Selecting the coffee taste Turn the coffee taste selection knob B8 to se lect the required taste Turning it clockwise incre ases the quantity of coffee beans the appliance will grind and therefore the strength of the coffee obtained MAX Ci Please note e The first time you use the appliance you will need to make a number of coffees to identify the correct knob position through trial and error e Make sure not to turn the knob too far clockwise otherwise the coffee may be de livered too slowly a drop at a time particu larly when making two cups of coffee Selecting the quantity of coffee in the cup Adjust the coffee quantity selection knob B9 to set the required quantity w w Turning it clockwise increases the amount of cof fee obtained g Please note The first time you use the appliance you will need to make a number of coffees to identify the correct knob position through trial and error Adjusting the coffee mill The coffee mill is set by default to prepare cof fee correctly and should not require regulating initially However if after making the first few coffees you find that the coffee is either too weak and not creamy enough or delivery is too slow a drop at a time this can be corrected by adjusting the grinding adjustment knob fig 7 g Plea
13. fee mill is very noisy this means a small stone in the coffee beans has blocked the mill Contact Customer Services 4o B 0000 B o 4 o B es A o oa 3 The light flashes The machine must be de scaled The descaling procedure described in the section Descaling needs to be performed as soon as possible There is an unusual noise and the lights flash alternately The infuser has not been replaced after cleaning Leave the service door closed and the infuser out of the coffee maker Press the CZ or CP VP but tons together until the four lights go off Only when all four lights are off can the door be opened and the infuser inserted 18 LIGHTS me OO DESCRIPTION The lights flash alternately MEANING The coffee maker has just been turned on the infu ser is not inserted correct ly and the service door is not correctly closed WHAT TO DO Press the word PUSH on the infu ser until it clicks into place Make sure the two red buttons have snapped out Close the service door and turn the appliance on again The lights flash The pre ground coffee Empty the funnel with the help of a 8 e e O O funnel is clogged brush as described in the section amp ow A Cleaning the pre ground coffee funnel The light is on The infuser has not been Insert the infuser as described in 9 9 gt O O steadily replaced after cleaning the paragraph
14. h The coffee maker is not ready to make Coffee the water has not yet reached the ideal temperature Wait for the lights to come on steadily before making coffee 660 The lights are on steadily The coffee maker is at the right tempera ture and ready to make coffee 56600 The light is on steadily The appliance is delivering one cup of coffee 5060 The light is on steadily The appliance is delivering two cups of coffee 5666 The steam light is flashing The coffee maker is heating up to the ideal temperature to produce steam Wait for the light to remain on steadily before using the steam function 2 5666 The steam light is on stea dily The appliance is ready to deliver steam 2 50400 The lights flash alternately The appliance is turning off see the sec tion Turning Off The lights flash You must turn the steam knob to posi tion The lights flash alternately You must turn the steam knob to posi tion 0 The light is on steadily The appliance is in energy saving mode ge O amp te A amp H eo 09 The light is on steadily The automatic descaling programme is i t A AM underway MEANING OF THE ALARM LIGHTS LIGHTS m oe O00 DESCRIPTION The light is on steadily MEANING Insufficient water in tank or tank not correctly in place WHAT TO DO Fill the tank with water and or in sert it co
15. iance on page 3 Troubleshooting and repairs In the event of problems first try and resolve them following the information given in the sec tions Meaning of the alarm lights on page 18 and Troubleshooting on page 19 If this does not resolve the problem or you re quire further information you should consult Customer Services by calling the number given on the annexed Customer Service sheet If your country is not among those listed on the sheet call the number given in the guarantee If repairs are required contact De Longhi Custo mer Services only The addresses are given in the guarantee certifi cate provided with the machine Fundamental safety warnings A Danger This is an electrical appliance and may therefore cause electric shock You should therefore respect the following safety warnings e Never touch the appliance with damp hands or feet e Never touch the plug with damp hands e Make sure the socket used is freely accessi ble at all times enabling the appliance to be unplugged when necessary e Unplug directly from the plug only Never pull the power cable as you could damage it e To disconnect the appliance completely pla ce the main switch at the back of the applian ce in the 0 position fig 6 e Ifthe appliance is faulty do not attempt to repair Turn it off unplug from the mains so cket and contact Customer Services e If the plug or power cable is damaged it mu
16. ining acid flows from the cap puccino maker Avoid contact with splashes of water 5 Press the f button and hold it down for at least 5 seconds to confirm that you have added the solution and begin the descaling procedure The light in the button remains on steadily to indicate that the descaling pro gramme has begun The CZ VT and lights flash simultaneously telling you to turn the steam knob to the position cof fee cannot be made 6 Turn the steam knob anticlockwise to the position The descaler solution flows out of the cappuccino maker into the underlying container The descale programme automatically per forms a series of rinses and pauses to remo ve limescale deposits from inside the machi ne After about 30 minutes the water tank is empty the 5S light comes on and the CZ O CZ and lights alternate Turn the steam knob clockwise as far as it will go to the 0 position The appliance is now ready for rinsing through with clean water 11 Empty the container used to collect the de scaler solution and replace it empty under the cappuccino maker Remove the water tank empty rinse under running water fill with clean water and repla ce The Z Y and dh lights flash simultaneously Turn the steam knob a half turn anticlockwise to the I position Hot water comes out of the spout When the water tank is completely empty the light goes out and the KS and Z SV lights flash Tu
17. l alarm B14 f button to select rinsing or descaling B15 Descaling light B16 ECO button to select energy saving mode B17 Energy saving mode light PRELIMINARY CHECKS Checking the appliance After removing the packaging make sure the product is complete and undamaged and that all accessories are present Do not use the appliance if it is visibly damaged Contact De Longhi Customer Services Installing the appliance A Important When you install the appliance you should re ad the following safety warnings The appliance gives off heat After positio ning the appliance on the worktop leave a space of at least 3 cm between the surfaces of the appliance and the side and rear walls and at least 15 cm above the coffee maker e Water penetrating the appliance could cau se damage Do not place the appliance near taps or sinks e The appliance could be damaged if the water it contains freezes Do not install the applian ce in a room where the temperature could drop below freezing point e Arrange the power cable in such a way that it cannot be damaged by sharp edges or con tact with hot surfaces e g electric hot pla tes Connecting the appliance A Important Check that the mains power supply voltage cor responds to the value indicated on the rating pla te on the bottom of the appliance Connect the appliance to an efficiently earthed and correctly installed socket with a minimum curren
18. leaning the cappuccino maker a little hot water is delivered Avoid contact with splashes of water 1 Deliver a little water for a few seconds by ro tating the steam knob to the position Then turn the steam knob to the 0 position to stop the flow of hot water 2 Wait for a few minutes for the cappuccino maker to cool down Grip the handle of the cappuccino maker tube firmly in one hand and with the other rotate the cappuccino maker anticlockwise fig 15 and remove by pulling downwards fig 16 3 Wash all parts of the cappuccino maker tho roughly with a sponge and warm water 4 Make sure the holes shown by the arrows in fig 17 are not blocked If necessary clean with a pin 5 Wash all parts of the cappuccino maker tho roughly with a sponge and warm water 6 Reinsert the nozzle and replace the cappuc cino maker on the nozzle turning it and pu shing it upwards until it is attached HEATING WATER 1 1 A Important Danger of burns Never leave the machine unsupervised while de livering hot water As shown below stop delivery of hot water when the cup is full The cappuccino maker becomes hot while water is being delivered and must be held by the handle only 1 Place a container under the cappuccino ma ker as close as possible to avoid splashes 2 Check that the and S7 lights are on steadily 3 Turn the steam knob a half turn anticlockwise as far as it will go Delivery begins 4 Stop
19. o exit the menu lava nrando The machine is now reprogrammed with the new water hardness setting TECHNICAL SPECIFICATION Voltage 220 240 V 50 60 Hz max 10A Absorbed power 1450W Pressure 15 bar Water tank capacity Tar L Size LxHxD 280x364x400 mm Cable length 15m Weight 10 8 kg C The appliance complies with the fol lowing EC directives e Stand by Directive no 1275 2008 Low Voltage Directive 2006 95 EC and sub sequent amendments e EMC Directive 2004 108 EC and subsequent amendments e Materials and accessories coming into con tact with food conform to EEC regulation 1935 2004 DISPOSAL Important information for correct disposal of the product in accordance with EC Directive 2002 96 EC At the end of its working life the product must not be disposed of as urban waste It must be taken to a special local authority dif ferentiated waste collection centre or to a dealer providing this service Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from inappro priate disposal and enables the constituent mate rials to be recovered to obtain significant savings in energy and resources As a reminder of the need to dispose of house hold appliances separately the product is mar ked with a rubbish bin bearing a cross MEANING OF LIGHTS DURING NORMAL OPERATION LIGHTS DESCRIPTION MEANING 5066 The lights flas
20. or a creamier froth rotate the container with slow movements in an upward direc tion You should not discharge steam for more than 3 minutes at a time 8 When you have obtained the required froth stop steam delivery by turning the steam knob back to the 0 position A Important Danger of burns Always turn the steam knob to the 0 position before removing the container with the fro thed milk to avoid burns caused by splashes of boiling milk 9 Add the milk froth to the cup of coffee pre pared previously The cappuccino is ready Sweeten to taste and if desired sprinkle the froth with a little cocoa powder Please note If immediately after making cappuccino and deactivating the steam function by pressing the steam button you press the Por XZ button because you want to make another coffee the coffee maker will be too hot the and CZ GF lights flash to in dicate an unsuitable temperature You must wait about ten minutes for the appliance too cool down sufficiently To cool it down more quickly after deactiva ting the steam function open the steam knob and let the water flow out of the cappuccino maker into a container until the lights C7 and CZ CZ stop flashing A Danger of burns Avoid contact with splashes of water Cleaning the cappuccino maker after use Clean the cappuccino maker each time you use it to avoid the build up of milk residues or blocka ges A Important Danger of burns When c
21. rn the knob to the 0 position fill the water tank again and the appliance goes off auto matically To use the appliance turn it on by pressing the d button 12 15 SETTING WATER HARDNESS The f light comes on after a period of time established according to water hardness The machine is set by default for a hardness va lue of 4 very hard water The machine can also be programmed according to the hardness of the mains water in the various regions so that the machine needs to be descaled less often Measuring water hardness 1 Remove the TOTAL HARDNESS TEST indi cator paper attached to this manual from its pack 2 Immerse the paper completely in a glass of water for one second 3 Remove the paper from the water and shake lightly After about a minute 1 2 3 or 4 red squares form depending on the hardness of the water Each square corresponds to one level Level 1 N Level 2 EN Level 3 mi iii Level 4 NENN Set water hardness 1 Make sure the appliance is off but connec ted to the mains electricity supply and with the main switch in the I position 2 Press and hold the button for at least 6 seconds The KS A W lights come on simultaneously 3 Press the ECO button to set the actual water hardness as measured by the indicator pa zs EH n per Level Level Level Level 1 2 3 4 o o QO a A 3M 4 Press the button t
22. rrectly pushing it as far as it will go until it clicks into place The tank is dirty and or clogged Rinse or descale the tank e OO The light flashes The grinding is too fine and the coffee is delivered too slowly Repeat coffee delivery and turn the grinding adjustment knob fig 10 one click clockwise towards T while the coffee mill is in ope ration If after making at least 2 coffees delivery is still too slow repeat the correction procedure turning the grinding adjustment knob another click until delivery is correct see the section Adju sting the coffee mill The machine is not able to make coffee If the problem persists turn the steam knob to the position and deliver water from the cappuccino maker O The light is on steadily The grounds container is full or missing Empty the grounds container and drip tray clean and replace fig 18 Important when removing the drip tray the grounds container MUST be emptied even if it contains few grounds If this is not done when you make the next coffees the grounds con tainer may fill up more than expec ted and clog the machine The light flashes The pre ground coffee function amp has been selected without placing any pre ground coffee in the funnel Place pre ground coffee in the fun nel or deselect the pre ground function The coffee beans have run out Fill the beans container If the cof
23. se note The grinding adjustment knob must only be tur ned when the coffee mill is in operation To obtain delivery not a drop at a time turn one click clockwise towards 7 For fuller bodied creamier coffee turn one click anti clockwise towards 1 do not turn more than one click at a time otherwise the cof fee could be delivered a drop at a time These adjustments will only be evident after at least 2 cups of coffee have been made If this adjustment does not obtain the desired result turn the knob another click Tips for a hotter coffee For hotter coffee you should e before delivering the coffee perform a rinse cycle by pressing the f button Hot water is delivered from the spout heating the inter nal circuits of the appliance and thus raising the coffee temperature e warm the cups by rinsing them with hot wa ter using the hot water function Making coffee using coffee beans A Important Do not use caramelised or candied coffee beans as they could stick to the coffee mill and make it unusable 1 Fill the container with coffee beans fig 8 2 Place under the coffee spouts 1 cup if you want 1 coffee fig 9 2 cups if you want 2 coffees 3 Lower the spouts as near as possible to the cup This makes a creamier coffee fig 10 4 Press the button corresponding to the num ber of coffees required 1 cup or 2 cups WX figs 11 and 12 5 Preparation begins and the
24. sliding it onto the internal support and pin at the bottom then push the PUSH symbol fully in until it clicks into place Q i Please note If the infuser is difficult to 2 insert before insertion EZ adapt it to the right size Ne by pressing the two levers shown in the figure Once inserted make sure the gt two red buttons have snapped out Replace the drip tray and grounds container Close the service door N ES o Descale the appliance when the f light on the panel flashes A Important Descaler contains acids which may irritate the skin and eyes It is vital to respect the manufacturer s safety warnings given on the descaler pack and the warnings relating to the procedure to follow in the event of contact with the skin and eyes i Please note Use De Longhi descaler only Under no circumstances should you use sulp hamic or acetic based descalers Their use in validates the guarantee Failure to descale the appliance as described above also invalidates the guarantee 1 Turn the machine on 2 Empty the water tank A12 3 Pour the descaler diluted with water respec ting the proportions indicated on the desca ler pack into the water tank Place an empty container with a minimum capacity of 1 5 litres under the hot water spout 4 Wait for the and S lights to come on steadily N Important Danger of burns Hot water conta
25. st be replaced by De Longhi customer services only to avoid all risk Important Keep all packaging plastic bags polystyrene foam away from children AN Important The appliance is not intended for use by persons including children with reduced physical sen sory or mental capabilities or lack of experien ce and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their sa fety Children must be supervised to ensure they do not play with the appliance A Danger Risk of burns This appliance produces hot water and steam may form while it is in operation Avoid contact with splashes of water or hot ste am DESIGNATED USE This appliance is designed and made to prepare coffee and heat drinks All other use is conside red improper This appliance is not suitable for commercial use The manufacturer is not liable for damage deri ving from improper use of the appliance This is a household appliance only It is not in tended to be used in e staff kitchen areas in shops offices and other working environments farm houses e by clients in hotels motels and other resi dential type environments e bed and breakfast type environments INSTRUCTIONS Read these instructions carefully before using the appliance Failure to respect these instructions may re sult in burns or damage to the appliance e The manufacturer is not lia
26. t rating of 10A only If the power socket does not match the plug on the appliance have the socket replaced with a suitable type by a qualified professional Using the appliance for the first time g Please note e Coffee has been used to factory test the ap pliance and it is therefore completely normal for there to be traces of coffee in the mill The machine is however guaranteed to be new e You should customise water hardness as soon as possible following the instructions in the section Setting water hardness on page 16 1 Remove the water tank fill to the MAX line with fresh water then replace in the appliance fig 1 2 Turn the cappuccino maker outwards and place a container with a minimum capacity of 100 ml underneath fig 2 3 Plug the appliance into the mains socket and place the main switch on the back of the ap pliance in m l D fig 3 4 Press the d fig 4 button fig 4 The Z7 JF b flash simultaneou sly 5 Turn the steam knob a half turn anticlockwise as far as it will go to position I fig 5 Water is delivered from the cappuccino maker it is normal forthe appliance to make some noise 6 Wait for delivery of hot water to stop auto matically The Z2 ZO lights flash to indicate that you must close the steam tap by turning the steam knob to the 0 position 7 Turn the steam knob to the O position The appliance goes off automatically To use the appliance turn it on i
27. th a brush and a sponge 2 Remove the residues with a vacuum cleaner fig 20 Cleaning the water tank 1 Clean the water tank A12 regularly about once a month and whenever you replace the water softener filter if provided with a damp cloth and a little mild washing up liquid 2 Fill the tank with fresh water and put back in the appliance Cleaning the coffee spouts 1 Clean the coffee spouts with a sponge or cloth fig 21 2 Check the holes in the coffee spout are not blocked If necessary remove coffee depo sits with a toothpick fig 22 Cleaning the pre ground coffee funnel Check regularly about once a month that the pre ground coffee funnel A8 is not blocked If necessary remove coffee deposits with a brush Cleaning the infuser The infuser A20 must be cleaned at least once a month A Important The infuser may not be extracted when the ma chine is on 1 Make sure the machine is correctly turned off see Turning off 2 Open the service door 3 Extract the drip tray and the grounds contai ner fig 18 4 Press the two red release buttons inwards and at the same time pull the infuser ou twards fig 23 AN Important RINSE WITH WATER ONLY NO WASHING UP LIQUID NO DISH WASHER Do not use washing up liquid to clean the infuser as it could cause damage 5 Soak the infuser in water for about 5 minu tes then rinse under the tap 6 After cleaning replace the infuser by
28. too slowly or a drop at a time The coffee is ground too finely Turn the grinding adjustment knob one click clockwise towards 7 while the coffee mill is in operation fig 7 Continue one click at a time until coffee delivery is satisfactory The effect is only visible after delivering 2 coffees see the section Adjusting the coffee mill on page 11 19 PROBLEM POSSIBLE CAUSE SOLUTION Coffee does not come out of one of the spouts e The spouts are blocked e Clean the spouts with a toothpick The coffee does not come out of the spouts but from around the service door e The holes in the spouts are clogged with dry coffee dust e The coffee guide inside the service door is blocked and cannot swing e Clean the spouts with a toothpick sponge or hard bristled kitchen brush e Thoroughly clean the coffee guide particularly near the hinges The frothed milk has large bubbles e The milk is not cold enough or is not semi skimmed e You should ideally use skimmed or semi skimmed milk at refrigerator temperature about 5 C If the result is not as you wished try changing brand of milk The milk is not frothed e Cappuccino maker dirty e Clean as described in the section Cleaning the cappuccino maker after use Steam delivery stops e A safety device stops steam delivery after 3 minutes e Wait then activate the steam function again
Download Pdf Manuals
Related Search