Akasa 2.5" Enclosure - Integral P2
Contents
1. ENGLISH AKASA Company notices The information contained in this document Is subject to change without notice All rights reserved Reproduction adaptation or translation of this material is prohibited without prior written permission of AKASA except as allowed under copyright laws The only warranties for AKASA products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty AKASA shall not be liable for technical or editorial errors or omissions contained herein Acknowledgements Microsoft Windows Windows NT and Windows XP are registered trademarks of MicrosoftCorporation Adobe and Acrobat are trademarks of Adobe Systems Incorporated Copyright 2006 AKASA ASIA Corporation General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners AKASA disclaims any and all rights in those marks Getting Started To install your new Enclosure you will need e Hard Disk Drive HDD not included e Micro Philips head screwdriver not included e Mounting screws included e USB 2 0 Data Cable included e USB to DC Power Cable included Installation 1 Undo the securing screws from the housing unit and open the back of the enclosure by sliding the tray out of the aluminum housing Note the IDE connector for the 2 5 HDD IDE Connecto2. If using the CD recording software Toast the extension driver for USB 2 0 must be installed Mac OS 8 6 For USB port installations on Mac OS 8 6 the USB Mass Storage Support 1 3 5 application must be installed Downloads of this software are available from the Apple Software Updates section at www apple com FCC Compliance Statement This Device complies with part 15 of the FCC Rules Operation is subiect to the following two conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may cause undesired operation
3. or written to the drive the LED will flash System Setup Setup instructions are outlined for each type of enclosure based on the computer s operating system i e Windows XP Windows 98 or Mac OS Windows XP 1 Windows XP will auto detect the new device and automatically load an embedded USB driver The following notification will appear in the bottom right hand corner of the screen Found New Hardware USB 2 0 Storage Device USB Device Found New Hardware Your new hardware is installed and ready to use 2 If the installed hard drive has not already been formatted in order for the computer to recognize the drive it must be initialized partitioned and formatted Click on Start and open the Control Panel Select Administrative Tools and open Computer Management Select Disk Management to launch the New Disk Wizard TE PR SS y p a a p y mr a ika be ikeen ihih 3 Follow the Wizard screens to initialize the drive irp twkre ane Gort Geek iirc Select hka to inini Wey rue miiie a dit hiii Lorca Dies Hiinaga Gar acces i Taari pae or ere Sain ig one Completing the Initialize and Convert Disk Wizard Su hee macceeetudy onegia ee ire rd Cae 4 The new device can now be viewed in Disk Management To launch the New Partition Wizard right button click in the Disk 1 area and select New Partition ina lee ee re Ct Kew Parliam Wuni Welcome to the New Par
4. r 2 Place the HDD on top of the tray and line up the IDE connectors with the drive Tray IDE Connector HDD IDE Connector 3 Gently insert the HDD into the tray s IDE connector until the connection is secure 4 While supporting the HDD with your hand gently turn the tray over and locate the HDD mounting holes Use the four 4 mounting screws provided to secure the HDD to the tray 5 Gently insert the tray back into the housing until the back panel fits against the housing integral 7 Plug the small flat end of the USB cable Mini B connector into the back of the enclosure 8 Insert the other end of the USB cable Type A Connector into any available active USB port on the computer F Note The 2 5 enclosure can draw power from the USB bus the cable carries both data and power In some cases the enclosure may require additional DC current for operation The additional USB to DC power converter cable is provided integral 9 If the HDD requires more power connect the USB portion Type A Connector of the USB to DC power cable to any available active USB port on the computer 10 Insert the other end of the USB to DC cable into the DC power port on the enclosure Note The integral logo on the front bezel serves two operational purposes It illuminates when power is being supplied to the enclosure and when there is drive activity i e when data is being read
5. tithon Wizard Tht Sel Paice jp Sree es eee ie b AAZ M el Oe PR A aati amd ippen des pe cane ary wees Meee oe MICE be Set de be Sa or Rte haul Pig coimas dii Page integral 5 Follow the wizard screens to complete the partitioning and formatting Select Primary Partition Set for maximum size ebk i Sia ae Pia i ia es et Re ded Se a beeg iya Later or Pa Fee sere pany fe gee dere mia ia jian pa ka paa papie 10 Assign the file format from the list displayed FAT32 or NTFS and select Perform a quick format Format Partii Te doe etn oe ey paion jay mit Et tt ine Oheces shana yay artis onal open peg hal eee pra eet te D Dar bye Pa Corte Completing the New Partition Wizard Tau hance ucceme uly completed fre fee Ppor gerd integral 6 Open My Computer The drive is now displayed and ready for use 11 12 Windows 98 When installing large capacity hard disk drives into the enclosure and in use with Win98 the Win98 OS may not properly recognize the full capacity of the HDD In order to remedy this situation Win98 may automatically ask to format the drive to its default capacity and or you may need to use a 3rd party application Mac OS 9 0 or later The Mac OS will auto detect the new device Once the Integral is installed on the computer via the USB an icon for the device will be displayed on the desktop
Download Pdf Manuals
Related Search