Home

Viewsonic PJ658 data projector

1. PICTURE AUTO KEYSTONE ZYEXECUTE IMAGE KEYSTONE 0 INPUT WHISPER NORMAL Select an item using the cursor buttons A on the MIRROR NORMAL VOLUME 16 projector or remote control and press the cursor button gt OPTION AUDIO on the projector or remote control or the ENTER button on the remote control to execute the item Then perform it EASY MENU referring to the following table Item Description AUTO KEY STONE EXE CUTE Selecting this item performs the Automatic keystone distortion cor rection Projector automatically corrects vertical keystone distortion due to the forward backward setup angle by itself This function will be executed only once when selected in the Menu When the slant of the projector is changed executes this function again When V INVERT or H amp V INVERT is selected to the MIRROR item in the SETUP menu if the projector screen is inclined or angled downward this function may not work correctly When the zoom adjustment is set to the TELE telephoto focus this correction may be excessive This function should be used when the zoom adjustment is set to the WIDE wide angle focus whenever possible When vertical degree is almost 0 degree the automatic keystone distortion correction may not work When vertical degree is over 30 degree the automatic keystone distortion correction may not work well This function will be unavailable when Transiti
2. 2 Remove the lens cover and set the power switch to E the ON position ERSA The power indicator will light up in steady orange Then 6 wait several seconds because the buttons may not func den tion for these several seconds m j 1 When AUTO ON in the OPTION menu is set to TURN ON The lamp will only be automatically turned on when the Power switch is turned on after the power was turned off by Power switch last time Afterwards the POWER indicator POWER will begin blinking in green When the power is completely eg ER FOR on the indicator will stop blinking and light in green PORER 2 When AUTO ON in the OPTION menu is set to TURN OFF el gt Blinking in green please see step 3 n Press the STANDBY ON button on the projector or the re o POWER mote control To display the picture select an input signal according to the sec tion Selecting an input signal Turning off the power Please pay special attention to below two points when you do 1 Please do not turn the projector on again for at least 10 minute in this case Neglect could shorten the lifetime of the lamp 2 During use or immediately after use do not touch around the lamp and vents of the projector It could cause a burn Press the STANDBY ON button on the projector or the remote control The message Power off will appear on the screen for about 5 l Steady green seconds gt Power off Press the STANDBY ON button
3. 83 mm 100 mm ViewSonic PJ658 62 Customer Support For technical support or product service see the table below or contact your reseller Note You will need the product serial number Country Region Web Site T Telephone F Fax E mail United States www viewsonic com support T 800 688 6688 F 909 468 1202 service us viewsonic com Canada www viewsonic com support T 866 463 4775 service ca viewsonic com United Kingdom www viewsoniceurope com uk T 0207 949 0307 service eu viewsoniceurope com Europe Middle East Baltic countries and North Africa www viewsoniceurope com Contact your reseller service eu viewsoniceurope com Australia and New Zealand www viewsonic com au support AUS 1800 880 818 NZ 0800 008 822 service au viewsonic com Singapore T 65 6273 4018 Malaysia www viewsonic com sg support service sg viewsonic com F 65 6273 1566 Thailand South T 886 2 2246 3456 Africa Other www viewsonic com service sd viewsonic com counties F 886 2 2249 1751 India www in viewsonic com T 91 44 52006500 service IN viewsonic com Hong Kong www hk viewsonic com support T 852 3102 2900 service hk viewsonic com Macau www hk viewsonic com support T 853 700 303 service hk viewsonic com Korea www viewsonic com T 080 2659 080 service kr vie
4. 1 Connect the connector of the power cord to the AC inlet of the projector 2 Firmly plug the power cord s plug into the outlet ViewSonic PJ658 14 EMMA CONN Putting batteries AWARNING Always handle the batteries with care and use them only as directed Battery may explode if mistreated Do not recharge disassemble or dispose of in fire And also improper use may result in cracking or leakage which could result in fire injury and or pollution of the surrounding environment Be sure to use only the batteries specified Do not use batteries of different types at the same time Do not mix a new battery with used one Make sure the plus and minus terminals are correctly aligned when loading a battery Keep a battery away from children and pets If swallowed consult a physician immediately for emergency treatment Do not short circuit or solder a battery Do not allow a battery in a fire or water Keep batteries in a dark cool and dry place If you observe a leakage of a battery wipe out the flower and then replace a battery If the liquid adheres to your body or clothes rinse well with water immediately Obey the local laws on disposing the battery 1 Remove the battery cover Slide back and remove the battery cover in the direction of the arrow 2 Insert the batteries Align and insert the two AA batteries according to their plus and minus termi nals as indicated in the remote control 3 Close the b
5. 44 OPTION Menu continued Item Description 1 3 If you have forgotten your PASSWORD 1 3 1 Follow the procedure in 1 1 1 to display the ENTER PASSWORD BOX 1 3 2 While the ENTER PASSWORD BOX is dis played press and hold the RESET button on SECUR UTYPASSRORD the remote control for about 3 seconds lupi ro eke eee The 10 digit Inquiring Code will be displayed NOTE If there is no key input for about 55 seconds Inquiring Code while the Inquiring Code is displayed the menu will PASSWORD close If necessary repeat the process from 1 3 1 1 3 3 Contact your dealer with the 10 digit Inquiring Code Your PASSWORD will be sent after your user registration information is confirmed 2 Using the MyScreen PASSWORD Function The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten 2 1 Turning on the MyScreen PASSWORD 4MyScreen PASSWORD SECURITY Function 2 1 1 Use the A Y buttons on the SECURITY menu to select MyScreen PASSWORD and press the button to display the MyScreen PASSWORD on off menu TURN ON TURN OFF MyScreen PASSWORD on off menu 2 2 Setting the PASSWORD 2 2 1 Display the MyScreen on off menu using the procedure in 2 1 1 MyScreen ENTER PASSWORD 0000 Z QUIT NEXT ENTER PASSWORD BOX small 2 2 2 Use the A V buttons on the MyScreen PASS WORD on off menu to select TURN ON Th
6. Start up MyScreen MyScreen lock Message Source name OPTION Menu 40 Auto search Auto keystone Auto on Auto off Lamp time Filter time My button Service Security Maintenance 50 LAMP isa asst are 50 Air filter llle 52 Other care 222222202 54 Troubleshooting 55 Related messages 55 Regarding the indicator lamps 56 Phenomena that may be easy to be mistaken for machine defects 58 Warranty and after service 61 Specifications 61 Customer Support 63 Limited Warranty 64 Projector features This projector is used to project various computer signals as well as NTSC PAL SECAM Component SD HD video signals onto a screen It requires just a little space for installation and gets a large image from short distance O High Brightness Newly developed 200W UHB Ultra High Brightness lamp gives you a higher brightness image on a screen The image can be still kept as bright and clean enough for use in bright rooms O Low Noise WHISPER mode is available for reducing acoustic noise to realize quieter operation It is perfect for use in low luminance rooms where low noise is more important than brightness O Rich Connectivity This projector has a variety of I O ports It can be easily connected to many sig nal sources like PC DVD and so on The rich connectivity provides you more options to make your pre
7. RGBIN1 gt RGBIN2 VIDEO gt S VIDEO gt COMPONENT VIDEO Press the RGB button on the remote control to select an input port for the RGB signal Each time you press the button the projector switches its RGB input port as below RGB INT RGB IN2 e f the RGB button is pushed when switching from VIDEO to RGB signals when TURN ON is selected for the AUTO SEARCH item in the OPTION menu the projector will check the RGB IN1 port first If no input is detected at the port the projector will check the RGB IN2 port VIDEO ROB SEARCH oO ASPECT AUTO BLANK N VN 7 ViewSonic PJ658 18 Selecting an input signal continued Press the VIDEO button on the remote control to select an input for video signal Each time you press the button the projector switches its video input port as below COMPONENT VIDEO S VIDEO VIDEO E e f the VIDEO button is pushed when switching from RGB to VIDEO signals when TURN ON is selected for the AUTO SEARCH item in the OPTION menu the projector will check the COMPONENT VIDEO port first If no input is de tected at the port projector will begin to check other ports in above order Searching an input signal 1 Press the SEARCH button on the remote control The projector will start to check its input ports in order to find any input signals When an input is found the projector will stop searching and display the image If no signal is found the projector will return to the state se
8. When there are no saved adjustment settings the following dialog is displayed ViewSonic PJ658 29 MG T MENU With the IMAGE menu items shown in the table below can be performed Select an item using the cursor buttons A on the projector or remote control and press the cursor button gt on the projector or remote control or the ENTER button on the remote control to execute the item Then perform it referring to the following table ASPECT 4 3 OVER SCAN 5 V POSITION 25 H POSITION 142 H PHASE 16 H SIZE 1344 EASY MENU AUTO ADJUST EXECUTE Description Using the buttons A switches the mode for aspect ratio For an RGB signal NORMAL amp 4 3 amp 16 9 amp SMALL ft lj ASPECT For a video signal s video signal or component video signal 4 3 16 9 amp 14 9 amp SMALL ft St For a no signal 4 3 fixed The NORMAL mode keeps the original aspect ratio of the signal Using the buttons A adjusts the over scan ratio Large It reduces picture lt gt Small It magnifies picture OVER SCAN This item can be selected only for a video s video and component signal When this adjustment is too large certain degradation may appear at the frame area of the picture In such a case please adjust small Using the buttons A adjusts the vertical position Up Down Over adjusting the vertical position may cause noise to appear on the screen If this occurs please reset
9. on the A N row to move the cursor to the name displayed on the first line and use the lt gt buttons to select character to be changed Once a character in the name is selected use the W button to move the cur sor back down to the character entry area to select and enter characters as described above 5 Select 7 and press the ENTER or IN PUT buttons when finished entering text To revert to the previous name without sav ing changes press the ESC or lt button and the INPUT button simultaneously ViewSonic PJ658 39 PINKON Menu With the OPTION menu the items shown in the table below can be performed AUTO SEARCH TURN OFF AUTO KEYSTONE TURN OFF Select an item using the cursor buttons A V on the projector or AUTO ON TURN OFF remote control and press the cursor button gt on the projector al Le or remote control or the ENTER button on the remote control to LAMP TIME Oh FILTER TIME Oh execute the item except for the items LAMP TIME and FILTER EW m Sr TIME Then perform it referring to the following table Item Description AUTO SEARCH Using the buttons A turns on off the automatic signal search func tion TURN ON amp TURN OFF When the TURN ON is selected detecting no signal automatically cycles through input ports in the following order The search is started from the current port Then when an input is found the proj
10. 45 minutes for the lamp to cool sufficiently Handling the lamp while hot can cause burns as well as damaging the lamp Never unscrew except the appointed marked by an arrow screws Do not open the lamp cover while the projector is suspended from the ceiling This is dangerous since if the lamp s bulb has broken the shards will fall out when the cover is opened In addition working in high places is dangerous so ask your local dealer to have the lamp replaced even if the bulb is not broken Do not use the projector with the lamp cover removed To replace the lamp make sure that the screws are tightened firmly Loose screws could result in damage or injury Use only the lamp of the specified type If the lamp breaks soon after the first time it is used it is possible that there are electrical problems elsewhere besides the lamp If this happens contact your local dealer or a service representative Handle with care jolting or scratching could cause the lamp bulb to burst during use Using the lamp for long periods of time could cause it dark not to light up or to burst When the pictures appear dark or when the color tone is poor please replace the lamp as soon as possible Do not use old used lamps this is a cause of breakage ViewSonic PJ658 50 Lamp continued A lamp has a finite product life Using the lamp for long periods of time could cause the pictures darker or the color tone poor Note th
11. 8 SE Ss lelvcleieiseiesises sls s s is e pag eet Riel el Oe eee EZ eel Oe ed EZ el nen cl oje Jo o ol lele ejolo siszlo vlo 9 S 5 JA SIR IP I Y IIIS a o Salciseici amp ieieieizieitisxiz z 18 2lso5leisjel l j o o eoj oj ol e c ols x g amp ge ge zx S c Du 6 7 S E ojo e rx ojo r o o o c6 T wm mwm eoj oljoj si vjr J oj c 1 oc E i g celelseiseisiwe e e amp lelwe iejlel s z E eilgalaieisie zi iwe s9jo jwol aqal o a ee s ass pe es e en ea 3 C MER Ello mlolalmlolalalalalom lt a P 9 I lt lt lt O S EA 5 IS a o Io Ee o ER 1 1 1 1 1 1 1 1 1 lt 3 5 2 e o we t elolelolsz o ielel te ala es oals xr 2 amp o 2 2 Ie u 2 lol IF g pgejgerrmejejej iz Ll S 8 c a lolol lelioleixleje zlvei 9 ES v e 9 o S 2 9 84 N S a o o Se a lalalalalalalalclalaiale Las d Sel coo u 2 lolo ejolz 9 z 9 9 S8I 8 8 9 Se lt o baud o H ed EZ E 4 8 38 9 9 ee ee epus Mjo Sle s r e xIg8 2 2 2 2 2 Oc we FPS PL IRI CIByoyelefelalal als 95 IE ND S S Sle lee 2 2 SI ee S og S t xl e l oj ve vel e x o 9 29 c5 KTH LK Js sIsn 15 Is IN o5 oc So Sz lelseielcialsis sie e sz s c D y EZ e elr ermE ejsejgIEIzizi amp I amp IS 5 a _ I 1 1 1 11 Bo we z tle l ej e x xleole ej e je 05 x gt o l eu we a o o co r o go 1T T 1 T T T T 1T T T T Le Sc S z iejsje s
12. BLANK BLACK Select an item using the cursor buttons A on the MM TE mai projector or remote control and press the cursor button gt OPTION y ee eae on the projector or remote control or the ENTER button SOURCE NAME on the remote control to execute the item Then perform it referring to the following table Description Using the buttons A switches the OSD On Screen Display language ENGLISH amp FRAN AIS amp DEUTSCH amp ESPANOL amp wail U LANGUAGE dd amp NEDERLANDS amp PORTUGU S amp Br BL SEM Rc Z SVENSKA PYCCKII amp SUOMI POLSKI amp T RK E 4 Using the buttons lt gt A adjusts the menu position MENU POSITION To quit the operation press the MENU button on the remote control or keep no operation for about 10 seconds Using the buttons A V switches the mode for the blank screen The blank screen is a screen for the temporarily blanking feature It is displayed by pressing the BLANK button on the remote control MyScreen amp ORIGINAL amp BLUE amp WHITE amp BLACK tt N BLANK MyScreen is a screen you can register as a desired screen The ORIGINAL screen is the existing standard screen BLUE WHITE and BLACK are non patterned plain screens in each color To avoid remaining as an afterimage the MyScreen and the ORIGINAL screens will change to the BLACK screen after several minutes For the MyScreen please refer to th
13. Stereo mini audio cable ViewSonic PJ658 12 Examples of connection with a VCR DVD player n the default setting the AUDIO IN3 L R port is the audio port for the VIDEO S VIDEO and COMPONENT VIDEO ports To change the settings refer to the AUDIO item in the SETUP menu Audio Video cable AUDIO IN2 VIDEO seo Video out Audio cable lt a AUDIO IN3 Audio R out Y AUDIO IN2 Audio L out IC A Es o S Video out S Video cable Component video out Y Oe Ca Ps CRIPR 4 Audio R out 1l Audio L out TI SCART cable G i B Ml R SCART Video ViewSonic PJ658 g g Bd lt Ww E ego AUDIO IN1 RGB OUT AUDIO OUT Ep _ ego RGB OUT AUDIO OUT Um 4g Component video cable AUDIO IN3 S VIDEO qm o RGB OUT AUDIO OUT eo Audio cable gt gt eg nnn ol IN1 A 5 pru AUDIO IN2 H VID EO RGB OUT AUDIO OUT CONTROL 13 Connecting power supply AC inlet Connector of the power cord
14. TURN ON is selected a moving picture is displayed more smoothly This function may cause a certain degradation of the picture In such a case please select the TURN OFF RGB IN Set the RGB input signal type for the RGB port 1 Use the lt gt buttons to select the RGB port to be set RGB1 amp RGB2 2 Use the A Y buttons to select the RGB input signal type SYNC ON G ON SYNC ON G OFF Selecting TURN ON turns on the SYNC ON G mode The SYNC ON G mode allows reception of SYNC ON G In the SYNC ON G mode the picture may be distorted with certain input signals In such a case remove the signal connector so that no signal is received and turn SYNC ON G off and then reconnect the signal RGB IN RGB1 RGB2 O b SYNC ON G ON SYNC ON G OFF ViewSonic PJ658 33 INPUT Menu continued Item Description The resolution for the RGB1 and RGB2 input signals can be set on this projector 1 In the INPUT menu select RESOLUTION using the A buttons and press the gt button The RESOLUTION menu will be displayed 2 In the RESOLUTION menu select the 1024x 768 resolution you wish to display using the A V STANDARD 1280x 768 buttons 1360x 768 Selecting AUTO will set a resolution appropri custom O 1440x 768 ate to the input signal c RESOLUTION MENU 3 Pressing the gt or Enter button when selecting a STANDARD resolution will auto matically adjus
15. Transition Detector CHECK PASSWORD rw 0000 w QUIT NEXT gt CHECK PASSWORD BOX Transition Detector COMPLETE 0000 ENTER EXIT PASSWORD BOX Pressing the ENTER button on the remote controll or the INPUT button on the projector will close the PASSWORD BOX NOTE Please do not forget your Transition Detector PASSWORD ViewSonic PJ658 48 OPTION Menu continued Item Description 4 3 Setting the Transition Detector off 4 3 1 Follow the procedure in 4 1 1 to display the Transition Detector on off menu 4 3 2 Select TURN OFF to display the ENTER PASSWORD BOX large Enter the registered PASSWORD and the screen will return to the Transition Detector on off menu If an incorrect PASSWORD is input the menu will close If necessary repeat the process from 4 3 1 SECURITY 4 4 If you have forgotten your PASSWORD 4 4 1 Follow the procedure in 4 1 1 to display the Transition Detector on off menu 4 4 2 Select TURN OFF to display the ENTER Transition Detector PASSWORD BOX large The 10 digit Inquir mL ing Code will be displayed inside the BOX Inquiring Code 4 4 3 Contact your dealer with the 10 digit Inquiring nn PASSWORD BOX Code Your PASSWORD will be sent after your large user registration information is confirmed ViewSonic PJ658 49 Maintenance Lamp A WARNING PA HIGH VOLTAGE AN HIGH TEMPERATURE A HIGH PRESSURE gt The projector uses a high press
16. and then perform the proper measure using the item descriptions below The lamp does not light and there is a possibil ity that interior portion has become heated Please turn the power off and allow the projector to Blinking cool down at least 20 minutes After the projector has In Red sufficiently cooled down please make confirmation of or the following items and then turn the power on again Blinking discre discre In Red tionary tionary Lighting Turned Lighting rend on Is there blockage of the air passage aperture In Red Is the air filter dirty Does the peripheral temperature exceed 35 C If the same indication is displayed after the remedy please change the lamp referring to the section Lamp The lamp cover has not been properly fixed Please turn the power off and allow the projector to cool down at least 45 minutes After the projector has Blinking Turned sufficiently cooled down please make confirmation of In Red off the attachment state of the lamp cover After perform ing any needed maintenance turn the power on again If the same indication is displayed after the remedy please contact your dealer or service company Blinking In Red or Lighting In Red ViewSonic PJ658 56 Regarding the indicator lamps continued LAMP TEMP indica indica Description tor tor POWER indicator The cooling fan is not operating Please turn the powe
17. on the projector or the remote control again while the message appears POWER The projector lamp will go off and the POWER indicator will begin E gt blinking in orange 9 Blinking in orange Then the POWER indicator will stop blinking and light in steady POWER orange when the lamp cooling is complete ia E oO ei ri e 3 Make sure that the power indicator lights in steady orange and nn set the power switch to the OFF position The POWER indicator will go off Attach the lens cover ViewSonic PJ658 17 Operating Adjusting the volume 1 Press the VOLUME button on the remote control Adialog will appear on the screen to aid you in adjusting the volume 2 Use the cursor buttons A V to adjust the volume To close the dialog and complete the operation press the VOLUME button again Even if you don t do anything the dia log will automatically disappear after a few seconds ol SASO ASPECT AUTO BLANK O OO Temporarily muting the sound ME aa G OO 1 Press the MUTE button on the remote control 1 Adialog will appear on the screen indicating that you have muted the sound ges To restore the sound press the MUTE or VOLUME button QQ aU Even if you don t do anything the dialog will automatically dis p d appear after a few seconds Selecting an input signal Press the INPUT button on the projector Each time you press the button the projector switches its input port as below j
18. this function is performed a certain extra such as a line may appear ViewSonic PJ658 27 PICTURE Menu continued Description Using the buttons A V switches the mode of color temperature HIGH DEFAULT amp HIGH CUSTOM amp MID DEFAULT amp MID CUSTOM gt LOW DEFAULT amp LOW CUSTOM amp Hi BRIGHT 1 DEFAULT Hi BRIGHT 1 CUSTOM gt Hi BRIGHT 2 DEFAULT amp Hi BRIGHT 2 CUSTOM To adjust CUSTOM Selecting the CUSTOM and then pressing the button gt or the ENTER button displays a dialog offset gt ul to aid you in adjusting the OFFSET and or GAIN f of the CUSTOM mode OFFSET adjustments change the color intensity on the whole tones of the test pattern 800 00 0B GAIN adjustments mainly affect color intensity WESEHEIIISISTNE on the brighter tones of the test pattern Choose an item using the buttons lt gt and adjust the level using the buttons A V You can display a test pattern for checking the effect of your adjust ment by pressing the ENTER button Each time you press the ENTER button the pattern changes as below No pattern gt Gray scale of 9 steps ft Ramp Gray scale of 15 steps When this function is performed a certain extra such as a line may appear Using the buttons A V adjusts the strength of whole color Strong Weak This item can be selected only for a video signal s video or com ponent vi
19. 0 GANMA DEFAULT 1 COLOR TEMP MIDDLE COLOR 0 TINT 0 SHARPNESS 3 MY MEMORY SAVE 1 EASY MENU Item Description BRIGHTNESS Using the buttons A V adjusts the brightness Light amp Dark CONTRAST Using the buttons A adjusts the contrast Strong amp Weak Using the buttons A switches the GAMMA mode 1 DEFAULT 1 CUSTOM 2 DEFAULT amp 2 CUSTOM 3 DEFAULT 5 CUSTOM 5 DEFAULT 4 CUSTOM 4 DEFAULT 3 CUSTOM To adjust CUSTOM Selecting a mode of CUSTOM and then pressing the button gt or the ENTER button displays a dialog to aid you in adjusting the mode This function is useful when you want to change the brightness of particular tones i Choose an item using the buttons lt gt and ed a Ss iis adjust the level using the buttons A V GAMMA You can display a test pattern for checking the effect of your adjust ment by pressing the ENTER button Each time you press the ENTER button the pattern changes as below No pattern gt Gray scale of 9 steps Ramp Gray scale of 15 steps The eight equalizing bars correspond to eight tone levels of the test pattern except the darkest in the left end If you want to adjust the 2nd tone from left end on the test pattern Gray scale of 9 steps use the equalizing adjustment bar 1 The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar When
20. E using V A button then press the gt button A dialog will appear 5 Press the A button to select RESET on the dia log It performs resetting the lamp time NOTE Please reset the lamp time only when you have replaced the lamp for a suitable indication about the lamp ViewSonic PJ658 51 Air filter AWARNING Before caring make sure the power switch is off and the power cable is not plugged in then allow the projector to cool sufficiently The care in a high temperature state of the projector could cause an electric shock a burn and or malfunction to the projector gt Use only the air filter of the specified type Do not use the projector with the air filter and the filter cover removed It could result in a fire and or malfunction to the projector gt The air filter should be cleaned periodically If the air filter becomes clogged by dust or the like internal temperatures rise and could cause a fire a burn and or malfunction to the projector NOTE Please replace the air filter when it is damaged or too soiled and also when you replace the lamp Please reset the filter time only when you have cleaned or replaced the air filter for a suitable indication about the air filter The projector may display the message such as CHECK THE AIR FLOW or turn off the projector to prevent the internal heat level rising If the air filter becomes clogged by dust or the like internal temperatures rise and could
21. ESET using the button A RESET CANCEL Please reset the lamp time only when you have replaced the lamp for a suitable indication about the lamp For the lamp replacement see the section Lamp The filter time is the time counted after the last resetting It is shown in the OPTION menu as the usage time of the air filter Pressing the RESET button on the remote control or the button gt of the projector displays a dialog To reset the filter time select the RESET using FILTER TIME the button A RESET CANCEL Please reset the filter time only when you have cleaned or replaced the air filter for a suitable indication about the air filter For the air filter cleaning see the section Air filter Sets the assigned function for the MY BUTTON1 and 2 buttons on the included remote control RGB1 Sets port to RGB1 RGB2 Sets port to RGB2 COMPONENT Sets port to COMPONENT S VIDEO Sets port to S VIDEO MY BUTTON VIDEO Sets port to VIDEO INFORMATION Displays INPUT INFORMATION AUTO KEYSTONE EXECUTE Performs automatic KEYSTONE correction MY MEMORY Loads MY MEMORY settings PICTURE MODE Changes the PICTURE mode FILTER RESET Displays the filter time reset confirmation dia logue ViewSonic PJ658 41 OPTION Menu continued Item Description SERVICE Selecting this item displays the SERVICE menu Select an item using the buttons A Y and press the button gt or the E
22. NTER button on the remote control to execute the item FAN SPEED AUTO ADJUST GHOST FILTER MESSAGE KEY LOCK L FACTORY RESET amp INFORMATION amp REMOTE FREQ J FAN SPEED Using the buttons A switches the rotation speed of the cooling fans The HIGH is the mode for use at highlands etc Note that the projector is noisier when the HIGH is selected HIGH amp NORMAL AUTO ADJUST Using the buttons A V enables disables the automatic adjustment When DISABLE is selected the automatic adjustment feature is disabled although rough adjustment is automatically performed depending on the basic setting ENABLE DISABLE Depending on conditions such as input image signal cable to the projec tor environment around the projector etc the automatic adjustment may not work correctly In such a case please choose DISABLE to disable the automatic adjustment and make adjustment manually GHOST 1 Select a color element of ghost using the buttons lt P gt 2 Adjust the selected element using the buttons A to disappear ghost FILTER MESSAGE Use the A F button to set the timer for the interval to show the message for cleaning up the air filter 50h amp 100h amp 200h amp 300h amp TURN OFF After selecting 50h 100h 200h or 300h the message RE MINDER HRS PASSED AFTER THE LAST FILTER CHECK will appear after the timer reaches the interval time set by the menu When the TURN OFF is chose
23. ON Blinking In Red or Lighting In Red Blinking In Red or Lighting In Red Lighting Alternative In Green blinking in Red NOTE When the interior portion has become overheated for safety purposes the power source is automatically turned off and the indicator lamps may also be turned off In such a case press the O OFF side of the power Switch and wait at least 45 minutes After the projector has sufficiently cooled down please make confirmation of the attachment state of the lamp and lamp cover and then turn the power on again ViewSonic PJ658 57 Phenomena that may be easy to be mistaken for machine defects AWARNING P Never use the projector if abnormal operations such as smoke strange odor excessive sound damaged casing or elements or cables penetration of liquids or foreign matter etc should occur In such cases imme diately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped contact your dealer or service company Before requesting repair please check in accor dance with the following chart This operation sometimes resolves your problem If the situation cannot be corrected 2 The projector s microprocessor may need to be e reset Please push the Restart switch by using a cocktail stick or similar and the projector will restart 3 Some setting may be wrong Please use the FACTORY RESET fun
24. ON 4 INPUT INFORMATION SERVICE mm So on FRAME LOCK AUTO SCART RGB The FRAME LOCK message on the dialog means the frame lock function is working The SCART RGB message means the COMPONENT VIDEO port is working as a SCART RGB input port Please refer to the COMPONENT item in this menu This item can t be selected for no signal and sync out FACTORY RESET Selecting RESET using the button A performs this function By this function all the items in all of menus will collectively return to the initial setting Note that the items LAMP TIME FILTER TIME LAN GUAGE and OPTION SECURITY are not reset RESET CANCEL ViewSonic PJ658 43 OPTION Menu continued Item Description SECURITY Please contact your local dealer 1 Using Security Features 1 1 Inputting the PASSWORD 1 1 1 Use the A buttons on the OPTION menu to select SECURITY and press the gt but ton The ENTER PASSWORD box will be displayed The factory default PASSWORD is 5847 This PASSWORD can be changed 1 2 Changing the PASSWORD NOTE It is strongly recommended the factory default PASSWORD to be changed as soon as possible 1 1 2 Use the A lt gt buttons to enter the registered PASSWORD Move the cursor to the right side of the ENTER PASSWORD BOX and press the button to display the SECURITY menu If an incorrect PASSWORD is input the ENTER PASSWORD BOX will be displayed again If incorrect PASSWORD is inpu
25. Phenomena that may be easy to be mistaken for machine defects continued Refer Phenomenon Cases not involving a machine defect ence page The signal cables are not correctly connected 12 13 Correctly connect the audio cables The MUTE function is working Restore the sound pressing the MUTE or VOLUME button 18 Sound does not on the remote control come out The volume is adjusted to an extremely low level Adjust the volume to a higher level using the menu function 18 or the remote control The AUDIO setting is not correct 36 Correctly set the AUDIO item in the SETUP menu The lens cap is attached 17 Remove the lens cover The signal cables are not correctly connected 12 13 Correctly connect the connection cables The brightness is adjusted to an extremely low level No pictures are nn ee s higher level using the menu func 25 displayed ion or the remote control The computer cannot detect the projector as a plug and play monitor 11 Make sure that the computer can detect a plug and play monitor using another plug and play monitor The BLANK screen is displayed 22 Press the BLANK button on the remote control Video screen The FREEZE function is working 22 display freezes Press the FREEZE button to restore the screen to normal Color settings are not correctly adjusted Colors havea Perform picture adjustments by changing the COLOR 26 28 faded out TEMP COLOR TINT an
26. SSED AFTER THE LAST FILTER CHECK FILTER MAINTENANCE IS ESSEN TIAL TO REMOVE WARNING MES SAGE RESET FILTER TIMER SEE MANUAL FURTHER INFO A note of precaution when cleaning the air filter Please immediately turn the power off and clean or change the air filter referring to the Air Filter section of this manu al After you have cleaned or changed the air filter please be sure to reset the filter timer ViewSonic PJ658 55 Regarding the indicator lamps Lighting and flashing of the POWER indicator the LAMP indicator and the TEMP indicator have the meanings as described in the table below Please follow the instructions within the table If the same indication is displayed after the remedy or if an indication other than the following is displayed please contact your dealer or service company LAMP TEMP indica indica Description tor tor POWER indicator Lighting Turned Turned The projector is in a standby state In Orange off off Please refer to the section Power On Off Blinking Turned Turned The projector is warming up In Green off off Please wait Lighting Turned Turned The projector is in an on state In Green off off Ordinary operations may be performed Blinking Turned Turned The projector is cooling down In Orange off off Please wait The projector is cooling down A certain error has been detected Please wait until the POWER indicator finishes blink ing
27. T GAMMA 2 DEFAULT DYNAMIC COLOR TEMP HIGH DEFAULT GAMMA 3 DE FAULT BOARD BLACK COLOR TEMP Hi BRIGHT 1 DEFAULT GAMMA 4 DEFAULT BOARD GREEN COLOR TEMP Hi BRIGHT 2 DEFAULT GAMMA 4 DEFAULT WHITEBOARD COLOR TEMP MID DEFAULT GAMMA 5 DEFAULT When the combination of GAMMA and COLOR TEMP differs from pre assigned modes above the display on the menu for the PICTURE MODE is CUSTOM Please refer to the GAMMA and COLOR TEMP items in the PICTURE menu When this function is performed a certain extra such as a line may appear BRIGHTNESS Using the buttons lt gt adjusts the brightness See the item BRIGHTNESS in the PICTURE menu ViewSonic PJ658 25 EASY Menu continued Item Description CONTRAST Using the buttons lt gt adjusts the contrast See the item CONTRAST of section PICTURE menu COLOR Using the buttons lt gt adjusts the strength of whole color See the COLOR item in the PICTURE menu TINT Using the buttons lt gt adjusts the tint See the TINT item in the PICTURE menu SHARPNESS Using the buttons lt gt adjusts the sharpness See the SHARPNESS item in the PICTURE menu There may be some noise when an adjustment is made This is not a malfunction WHISPER Using the buttons lt P gt turns off on the whisper mode See the WHISPER item in the SETUP menu MIRROR Using the butt
28. ViewSonic PJ658 LCD Projector User Guide Guide de l utilisateur Bedienungsanleitung Guia del usuario Guida dell utente Guia do usu rio Anv ndarhandbok K ytt opas PyKoBOACTBO NONB30BAaTenA dE dE AFS AF eru Aj eam A RU ViewSonic Model No VS11361 Compliance Information For U S A This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 The device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the s
29. about 30 minutes passed When no input is detected after the power on and AUTO OFF time is set to 1 to 99 the projector will be turned off after the passed time reaches at the set time If one of the projector s buttons or the remote control buttons is pressed or one of the commands except get commands is transmitted from the control port during the corresponding time projector will not be turned off ViewSonic PJ658 40 OPTION Menu continued Item Description Using the buttons A adjusts the time to count down to automati cally turn the projector off Long max 99 minutes Short min 0 minute DISABLE 4 AUTO OFF X ey When the time is set to 0 the projector is not turned off automati AUTO OFF cally When the time is set to 1 to 99 and when the passed time with no signal or an unsuitable signal reaches at the set time the projector lamp will be turned off If one of the projector s buttons or the remote control buttons is pressed or one of the commands except get commands is trans mitted from the control port during the corresponding time projector will not be turned off Please refer to the section Turning off the power The lamp time is the time counted after the last resetting It is shown in the OPTION menu as the usage time of the lamp Pressing the RESET button on the remote control or the button gt of the projector displays a dialog To reset the lamp time select the LAMP TIME R
30. al seconds with no C2 operation and the projector will enter the MAGNIFY mode ao olo Use the cursor buttons A Y to adjust the zoom level To move the zoom area press the POSITION button in the MAGNIFY mode then use the cursor buttons A V 4 to move the area And to finalize the zoom area press the POSITION button again To exit the MAGNIFY mode and restore the screen to normal press the OFF button of MAGNIFY on the remote control e The projector automatically exits the MAGNIFY mode when the input signal is changed or when the display condition is changed e Although in the MAGNIFY mode the keystone distortion condition may vary it will be restored when the projector exits the MAGNIFY mode ViewSonic PJ658 21 Freezing the screen 1 Press the FREEZE button on the remote control The FREEZE indication will appear on the screen and the DIO projector will enter the FREEZE mode OUO QO O OJO To exit the FREEZE mode and restore the screen to normal G SOE press the FREEZE button again e The projector automatically exits the FREEZE mode when the input signal changes or when one of the projector s buttons or the remote control buttons of STANDBY ON SEARCH RGB VIDEO BLANK AUTO ASPECT VOL UME MUTE KEYSTONE POSITION MENU MAGNIFY and MY BUTTON is pressed e f the projector continues projecting a still image for a long time the LCD panel might possibly be printed Do not leave the proj
31. ar the projec tor Do not use aerosols or sprays ACAUTION Please take right care of the projector according to the follow ing Incorrect care could cause not only an injury but adverse influence such as discoloration peeling paint etc gt Do not use cleaner or chemicals other than those listed below gt Do not polish or wipe with hard objects Inside of the projector In order to ensure the safe use of your projector please have it cleaned and in spected by your dealer about once every year Caring for the lens If the lens is flawed soiled or fogged it could cause deterioration of display qual ity Please take care of the lens being cautious of handling Turn the projector off and unplug the power cord Allow the projector to cool sufficiently After making sure that the projector is cool adequately lightly wipe the lens with a commercially available lens cleaning wipe Do not touch the lens di rectly with your hand Caring for the cabinet and remote control Incorrect care could have adverse influence such as discoloration peeling paint etc 1 Turn the projector off and unplug the power cord Allow the projector to cool sufficiently 2 After making sure that the projector is cool adequately lightly wipe with gauze ora soft cloth If soiling is severe dip soft cloth in water or a neutral cleaner diluted in water and wipe lightly after wringing well Then wipe lightly with a soft dry cloth ViewSoni
32. at each lamp has a dif ferent lifetime and some may burst or burn out soon after you start using them Preparation of a new lamp and early replacement are recommended To prepare a new lamp contact your dealer and tell the lamp type number Type number RLC 017 Turn the projector off and unplug the power cord Allow the lamp to cool for atleast 45 minutes 2 Prepare a new lamp Ifthe projector is mounted on the ceiling or if the lamp has broken also ask the dealer to replace the lamp gt Lamp cover In the case of replacement by yourself 3 Loosen the lamp cover screw marked by arrow and then slide the lamp cover to the side to re move it 4 Loosen the 2 screws marked by arrow of the lamp and slowly pick up the lamp by the handles 5 Insert the new lamp and retighten firmly the two screws that are loosened in the previous process to lock it in place 6 Slide the lamp cover back in place and firmly fas ten the lamp cover a screw Turn the projector on and reset the lamp time us SEIT ing the LAMP TIME function in the OPTION menu li ay 1 Press the MENU button to display a menu Only Handle when the EASY MENU has appeared please per form the next step 2 2 Point at the Go to Advanced Menu in the menu using V A button then press the button 3 Point at the OPTION in the left column of the menu using V A button then press the button 4 Point at the LAMP TIM
33. attery cover Replace the battery cover in the direction of the arrow and snap it back into place ViewSonic PJ658 15 Using the remote control ACAUTION P Be careful in handling the remote control Do not drop or expose the remote control to physical impact Do not get the remote control wet or place it on wet objects It may result in malfunction Remove the batteries from the remote control and store them in a safe place if you won t be using the remote control for an extended period Replace the batteries whenever the remote control starts malfunctioning When strong lights such as direct sunlight or light from an extremely close range such as from an inverter fluorescent lamp hit the projector s remote sensor the remote control may cause to function Adjust the direction of the projector to keep the light from directly hitting the projector s remote sensor The signal settings for the remote control transmitter and the projector s remote sensor can be changed If the remote control does not function properly try changing the signal setting Changing the signal setting for the remote control transmitter 1 Setting 1 FREQ NORMAL Simultaneously press and hold the MUTE and RESET buttons for about 3 seconds 2 Setting 2 FREQ HIGH Simultaneously press and hold the MAGNIFY OFF and ESC buttons for about 3 seconds Setting 1 is the factory default setting When the batteries are removed from the remote con
34. c PJ658 54 Nroubleshooting Related messages When the unit s power is on messages such as those shown below may be dis played When any such message is displayed on the screen please follow the instructions described below If the same message is displayed after the remedy or if a message other than the following appears please contact your dealer or Service company Although these messages will be automatically disappeared around several min utes it will be reappeared every time the power is turned on Message Description NO INPUT IS DETECTED xokck There is no input signal Please confirm the signal input connection and the status of the signal source SYNC IS OUT OF RANGE xk fH gt gt kHz fV KHZ The horizontal or vertical frequency of the input signal is not within the specified range Please confirm the specs for your projector or the signal source specs CHECK THE AIR FLOW The internal temperature is rising Please turn the power off and allow the projector to cool down at least 20 minutes After having confirmed the follow ing items please turn the power ON again Is there blockage of the air passage aperture s the air filter dirty Does the peripheral temperature exceed 35 C If the same indication is displayed after the remedy please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH REMINDER HRS PA
35. cause a fire a burn and or malfunction to the projector When the indicators or a message prompts you to clean the air filter clean the air filter as soon as pos sible Please check and clean the air filter periodically even if there is no message Please replace the air filter when it is damaged or too soiled Preparation of a new air filter is recommended To prepare a new air filter contact your dealer and tell the air filter type number And also when you replace the lamp please replace the air filter An air filter of specified type will come together with a replacement lamp for this projector Turn the projector off and unplug the power cord Allow the lamp to cool for at least 45 minutes When the projector is suspended from the ceiling apply the vacuum cleaner to and around the filter cover first to prevent pen etration of dust or the like 3 While supporting the projector with one hand use your other hand to pull the filter cover forward in the direction of the arrow Remove the air filter Handle Filter cover ViewSonic PJ658 52 Air filter continued Apply a vacuum cleaner to the air filter and the filter cover Please replace the air filter when it is damaged or too soiled Replace the air filter in its original po sition Secure the air filter in place by pressing each of the six D locations Make sure there is no dust or dirt remain ing after the cover is in place If any
36. consumer purchaser What the warranty does not cover 1 Any product on which the serial number has been defaced modified or removed 2 Damage deterioration or malfunction resulting from a Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied with the product Repair or attempted repair by anyone not authorized by ViewSonic Any damage of the product due to shipment Removal or installation of the product Causes external to the product such as electric power fluctuations or failure Use of supplies or parts not meeting ViewSonic s specifications Normal wear and tear Any other cause which does not relate to a product defect 3 p product exhibiting a condition commonly known as image built in which results when a static image is displayed on the product for an extended period of time 4 Removal installation and set up service charges How to get service 1 For information about receiving service under warranty contact ViewSonic Customer Support You will need to provide your product s serial number 2 To obtain warranted service you will be required to provide a the original dated sales slip b your name c your address d a description of the problem and e the serial number of the product Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSon
37. control during this opera tion Selecting this item performs the automatic adjustment feature For an RGB signal The vertical position the horizontal position the horizontal phase and the horizontal size will be automatically set to default And the aspect ratio will be automatically selected Make sure that the application window is set to its maximum size prior to attempting to use this feature A dark picture may still be incorrectly adjusted Use a bright picture when adjusting For a video signal or s video signal The video format best suited for the respective input signal will be AUTO ADJUST selected automatically EXECUTE This function is available only when the AUTO mode is selected to the VIDEO FORMAT item in the INPUT menu For a component video signal the signal type is identified automatically independent ly of this function For a video signal s video signal or component video signal The vertical position horizontal position and aspect ratio will be automatically set to default For a component video signal The horizontal phase will be automatically set to default The automatic adjustment operation requires about 10 seconds Also please note that it may not function correctly with some input ViewSonic PJ658 31 ANA MENU With the INPUT menu the items shown in the table below can be performed Select an item using the cursor buttons A on the projector or remote control and press the cur
38. ct CES AUTO or MANUAL operation and press the button to OO OQ perform the following 1 AUTO executes automatic vertical keystone correction 2 MANUAL displays a dialog for vertical keystone correction Use the buttons A V for adjustment To close the dialog and complete this operation press the KEYSTONE button again Even if you don t do anything the dialog will automatically disappear after a few seconds e The adjustable range for correction will vary among inputs For so function may not work well e When V INVERT or H amp V INVERT is selected to the MIRROR item in the SETUP menu if the projector screen is inclined or angled downward the Auto Keystone function may not work correctly e When the zoom adjustment is set to the TELE telephoto focus this correction may be excessive This function should be used when the zoom adjustment is set to the WIDE wide angle focus whenever possible e When vertical degree is almost 0 degree the automatic keystone distortion cor rection may not work e When vertical degree is almost 30 degree the automatic keystone distortion correction may not work well e This function wil be unavailable when Transition Detector is on 0 um KEYSTONE A this Using the magnify feature 1 Press the ON button of MAGNIFY on the remote control SAGO The MAGNIFY indication will appear on the screen al 5 pex though the indication will disappear in sever
39. ction of the SERVICE item in the OPTION menu to reset all settings to factory default Then if the problem is not removed after the remedy please contact your dealer or service company Refer Phenomenon Cases not involving a machine defect ence page The electrical power cord is not plugged in 44 Correctly connect the power cord The power switch is not set to the on position 47 Set the power switch to On The main power source has been interrupted during operation such as by a power outage blackout etc 47 Power does not Please turn the power off and allow the projector to cool come on down at least 2 minutes then turn the power on again Either there is no lamp and or lamp cover or either of these has not been properly fixed Please turn the power off and allow the projector to cool down 56 57 at least 45 minutes After the projector has sufficiently cooled i down please make confirmation of the attachment state of the lamp and lamp cover and then turn the power on again The signal cables are not correctly connected Correctly connect the connection cables 123 Neither sounds Signal source does not correctly work nor pictures are Correctly set up the signal source device by referring to the outputted manual of the source device The input changeover settings are mismatched 18 19 Select the input signal and correct the settings ViewSonic PJ658 58
40. d or COLOR SPACE settings us 32 appearance or ing the menu functions Color tone is COLOR SPACE setting is not suitable poor Change the COLOR SPACE setting to AUTO RGB 32 SMPTE240 REC709 or REC601 ViewSonic PJ658 59 Phenomena that may be easy to be mistaken for machine defects continued Phenomenon Cases not involving a machine defect The brightness and or contrast are adjusted to an extremely low level Adjust BRIGHTNESS and or CONTRAST settings to a high er level using the menu function Pictures appear The WHISPER function is working dark Select NORMAL for the WHISPER item in the SETUP menu The lamp is approaching the end of its product life time Replace the lamp Either the focus and or horizontal phase settings are not properly adjusted Pictures appear Adjust the focus using the focus ring and or H PHASE us blurry ing the menu function The lens is dirty or misty Clean the lens referring to the section Caring for the lens NOTE Although bright spots or dark spots may appear on the screen this is a unique characteristic of liquid crystal displays and it does not constitute or imply a machine defect ViewSonic PJ658 60 Warranty and after sejvice If a problem occurs with the equipment first refer to the Troubleshooting and run through the suggested checks If this does not resolve the problem please contact your dealer or service company They will tell you
41. deo signal Using the buttons A adjusts the tint Greenish amp Redish This item can be selected only for a video signal s video or com ponent video signal Using the buttons A V adjusts the sharpness Strong Weak SHARPNESS There may be some noise and or the screen may flicker for a mo ment when an adjustment is made This is not a malfunction COLOR TEMP ViewSonic PJ658 28 PICTURE Menu continued Description Selecting a mode of MY MEMORY using the buttons A and then pressing the button or the ENTER button performs each function m LOAD2 LOADS LOAD4 SAVEA SAVE3 SAVE2 SAVE1 This projector has 4 numbered memories for adjustment data Performing the LOAD1 LOAD2 LOADS or LOADA loads the data on the memory whose number corresponds to the command s number and adjusts the picture automatically depending on the data Performing the SAVE1 SAVE2 SAVE3 or SAVE4 saves the current adjustment data on the memory whose number corresponds to the command s number MY MEMORY The current adjustment data of the items in the PICTURE menu is stored There may be some noise and or the screen may flicker for a mo ment when data is loaded to memory This is not a malfunction When the current settings are not saved to memory the following dialog is displayed Temporary condition MEMORY MEET Ml EST WEG UGS GEM wit To load saved adjustment settings press the MEMORY button
42. displayed ViewSonic PJ658 24 SAD MEHU AUTO KEYSTONE EXECUTE i i i i KEYSTONE e With the EASY MENU items shown in the table below can PICTURE MODE NORMAL be performed BRIGHTNESS 2 CONTRAST _ Select an item using the cursor buttons A V on the UR projector or remote control Then perform it referring to the SHARPNESS LCS i WHISPER NORMAL following table ISTE NORMAL RESET FILTER TIME Oh LANGUAGE ENGLISH Go to Advanced Menu EASY MENU RGB1 Item Description ASPECT Using the buttons lt gt switches the mode for aspect ratio See the ASPECT item in the IMAGE menu AUTO KEY Using the button gt executes the auto keystone function STONE EXE See the AUTO KEYSTONE EXECUTE item in the SETUP menu CUTE This function will be unavailable when Transition Detector is on Using the buttons lt gt corrects the keystone distortion KEYSTONE See the item KEYSTONE of section SETUP menu This function will be unavailable when Transition Detector is on PICTURE MODE Using the buttons lt gt switches the mode of picture type The modes of picture type are combinations of a mode of GAMMA and a mode of COLOR TEMP Choose a suitable mode according to the projected source C NORMAL amp CINEMA amp DYNAMIC WHITEBOARD amp BOARD GREEN amp BOARD BLACK NORMAL COLOR TEMP MID DEFAULT GAMMA 1 DEFAULT CINEMA COLOR TEMP LOW DEFAUL
43. dust or dirt remains use a vacuum cleaner to remove it as when placing the filter cover on the air filter Reattach the filter cover to the projector by aligning the filter cover with the grooves on the projector While holding the handle push down on the filter cover until it locks firmly in place Turn the projector on and reset the filter time using the FILTER TIME function in the OP TION menu 1 Press the MENU button to display a menu When the EASY MENU has ap peared please skip the next step 2 2 Point at the OPTION in the left column of the menu using V A button then press the button 3 Point at the FILTER TIME using V A button then press the button A dialog will appear 4 Press the A button to select RESET on the dialog It performs resetting the filter time knob Air filter Filter cover ViewSonic PJ658 53 Other care AWARNING P Before caring make sure the power switch is off and the power cable is not plugged in and then allow the projector to cool sufficiently The care in a high temperature state of the projector could cause a burn and or malfunction to the projector gt Never try to care for the inside of the projector personally Doing is so dan gerous gt Avoid wetting the projector or inserting liquids in the projector It could result in a fire an electric shock and or malfunction to the projector Do not put a container containing water cleaner or chemicals ne
44. e ENTER PASSWORD BOX small will be dis played 2 2 3 Use the A lt P buttons to enter the PASS WORD Move the cursor to the right side of the ENTER PASSWORD BOX small and press the button to display the CHECK MyScreen CHECK PASSWORD a 0000 v QUIT NEXT gt PASSWORD BOX enter the same PASS CHECK PASSWORD WORD again BOX ViewSonic PJ658 45 OPTION Menu continued Item Description 2 2 4 Move the cursor to the right side of the CHECK PASSWORD BOX and press the gt WyScreen button to display the PASSWORD for about COMPLETE 20 seconds please make note of the PASS 0000 WORD during this time After the PASSWORD has displayed for about 20 seconds the screen EMEN P will return to the MyScreen PASSWORD on off menu Pressing the ENTER button on the remote control or INPUT button on the projector will close the PASS WORD box When a PASSWORD is set for MyScreen The MyScreen registration function and menu will be unavailable The START UP setting will be locked on MyScreen and the menu will be unavailable Turning the MyScreen PASSWORD off will allow normal operation of both functions 2 3 Turning the PASSWORD off 2 3 1 Follow the procedure in 2 1 1 to display the MyScreen PASSWORD on off menu 2 3 2 Select TURN OFF to display the ENTER PASSWORD BOX large Enter the registered PASSWORD and the screen will return to the SECURITY MyScreen on off menu If an inco
45. e MyScreen item ViewSonic PJ658 37 SCREEN Menu continued Description START UP Using the buttons A switches the mode for the start up screen The start up screen is a screen displayed when no signal or an unsuitable signal is detected MyScreen amp ORIGINAL amp TURN OFF ft f MyScreen is a screen you can register as a desired screen The ORIGINAL screen is the existing standard screen When TURN OFF is selected the BLACK screen is used To avoid remaining as an afterimage the MyScreen and the ORIGINAL screens will change to the BLANK screen after several minutes If also the BLANK screen is the MyScreen or ORIGINAL it will change to the BLACK screen For the MyScreen please refer to the item MyScreen below For the BLANK screen please refer to the BLANK item This function will be unavailable and fixed to Myscreen when MyScreen Password in the Security Menu is on MyScreen This item functions for capturing the MyScreen of the blank screen and the start up screen Please execute displaying the input includ ing the picture you want to capture 1 Selecting this item displays a dialog titled MyScreen It will ask you if you start capturing the picture from the current screen Please wait for the target picture to be displayed and press the ENTER button on the remote control when the picture is displayed The picture will freeze and the frame for capturing appears To stop
46. e unit has been damaged in any way such as if the power supply cord or plug is damaged if liquid is spilled onto or objects fall into the unit if the unit is exposed to rain or moisture or if the unit does not operate normally or has been dropped ViewSonic PJ658 ii Copyright Information Copyright ViewSonic Corporation 2006 All rights reserved Macintosh and Power Macintosh are registered trademarks of Apple Computer Inc Microsoft Windows Windows NT and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries ViewSonic the three birds logo OnView ViewMatch and ViewMeter are registered trademarks of ViewSonic Corporation VESA is a registered trademark of the Video Electronics Standards Association DPMS and DDC are trademarks of VESA PS 2 VGA and XGA are registered trademarks of International Business Machines Corporation Disclaimer ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from furnishing this material or the performance or use of this product In the interest of continuing product improvement ViewSonic Corporation reserves the right to change product specifications without notice Information in this document may change without notice No part of this document may be copied reproduced or transmitted by any means for any purpose without
47. ector in the FREEZE mode for too long Temporarily blanking the screen 1 Press the BLANK button on the remote control The blank screen will be displayed instead of the screen of input signal Please refer to the BLANK item in the SCREEN menu el ASPECT AUTO BLANK EEE EN To exit the blank screen and return to the input signal screen press the BLANK button again e The projector automatically returns to the input signal screen when one of the projector s buttons or the remote control buttons is pressed or one of the com mands except get commands is transmitted from the control port ViewSonic PJ658 22 Operating the computer screen NOTE It may not be possible to control notebook PC and other computers with built in pointing device e g track ball using this remote control In this case before connecting go into BIOS system setup and select external mouse and disable the pointing device In addition the mouse may not function if the computer does not have the needed utility program See your computer s hardware manual for details The USB control can be used with Windows 95 OSR 2 1 or higher It may not be possible to use the remote control depending on the computer s configurations and mouse drivers The USB control can be used only for the functions listed below You cannot do things like press two buttons at once for instance pressing two buttons at the same time to move the mouse pointer diagona
48. ector will stop searching and display the image RGB IN1 gt RGB IN2 gt COMPONENT VIDEO gt S VIDEO gt VIDEO ft AUTO KEY STONE Using the buttons A turns on off the automatic keystone function TURN ON amp TURN OFF TURN ON Automatic keystone distortion correction will be execut ed whenever changing the slant of the projector TURN OFF This function is disabled Please execute the AUTO KEYSTONE EXECUTE in the SETUP Menu for automatic keystone distortion correction When the projector is suspended from the ceiling this feature will not function properly so select TURN OFF This function will be unavailable when Transition Detector is on AUTO ON Using the buttons A turns on off the AUTO ON function TURN ON amp TURN OFF When set to TURN ON the lamp will only be automatically turned on when the Power switch is turned on after the power was turned off by Power Switch last time The lamp will not be automatically turned on when the Power switch is turned on if the lamp was turned off with the following procedures The lamp was turned off with a remote control projector button or power turn off command The lamp was turned off with an AUTO OFF function The lamp was turned on by an AUTO ON function and was turned off about 30 minutes after no signal had been detected When no input is detected after the power on and AUTO OFF time is set to 0 the projector will be turned off after
49. egal rights and you may also have other rights which vary from state to state Some states do not allow limitations on implied warranties and or do not allow the exclusion of incidental or consequential damages so the above limitations and exclusions may not apply to you Sales outside the U S A and Canada For warranty information and service on ViewSonic products sold outside of the U S A and Canada contact ViewSonic or your local ViewSonic dealer Warranty Projectors Rev 1d lofl 4 3 Projector Warranty Release Date 03 31 05 ViewSonic PJ658 64 Pe means ROO ViewSonic
50. ejs e co o e x e oE Oo c cIcoIcja ano a jo o N o geE ej J L I jgjgegjejsegel B Ng o OF 8 lo seloelelelelelsisisaisisals So 3 s RA Jo IT IS S IS IN ISIS S La PJ658 ViewSonic Adjusting the projector s elevator You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you otherwise need to adjust the angle of projection The adjustment range of the elevator feet is O to 9 degrees Elevator feet Elevator button 1 After making sure that the projector is cool adequately press and hold in the elevator buttons while holding the projector The elevator buttons and the elevator feet are on the both sides 2 Raise or lower the projector to the desired height and release the elevator buttons When you release the elevator buttons the elevator feet will lock into posi tion 3 If necessary you can also finely adjust the height of the projector by twisting the elevator feet by hand ViewSonic PJ658 9 Using the Security Bar A commercial anti theft chain or wire can be attached to the security bar on the projector How to attach An anti theft chain or wire can be at tached as shown in the illustration Anti theft chains or wires of up to 10mm in diameter can be used Anti theft chain or wire sold separately ViewSonic PJ658 10 Connecting your devices NOTE Whenever attempting to connect a laptop computer to the pr
51. em to operate AUTO KEISTONEZS SE KEYSTONE e 4 Use the cursor buttons lt P gt to operate the item RR y CONTRAST In the Advanced MENU E 3 Use the cursor buttons A Y to select a menu MIRO mm If you want to change it to the EASY MENU select the pii dd AMENS did ndis Then press the cursor button on the projector or remote ee eee control or the ENTER button on the remote control to select an item The display of the selected menu will be active 3 Use the cursor buttons A V to select an item to operate Then press the cursor button on the projector or remote control or the ENTER button on the remote control to progress The operation menu of the selected item will appear 4 Use the cursor buttons A to operate the item e When you want to reset the operation press the RESET button on the remote control during the operation Note that items whose functions are performed simultaneously with operation ex LANGUAGE H PHASE VOLUME etc cannot be reset e In the advanced menu when you want to return to the previous display press the cursor button lt on the projector or remote control or the ESC button on the remote control Press the MENU button on the remote control again to close the menu and complete this operation Even if you don t do anything the dialog will auto matically disappear after about 10 seconds e Some functions cannot be performed when a certain input port is selected or when a certain input signal is
52. eparation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Warning To assure continued FCC compliance the user must use grounded power supply cord and the cables which are included with the equipment or specified Also any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device For Canada This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada For European Countries CE Conformity The device complies with the requirements of the EEC directive 89 336 EEC as amended by 92 31 EEC and 93 68 EEC Art 5 with regard to Electromagnetic compaty and 73 23 EEC as amended by 93 68 EEC Art 13 with regard to Safety User Information for all Countries Notice Use the cables which are included with the unit or specified ViewSonic PJ658 i Important Safety Instructions 1 2 10 11 12 13 14 Read these instructions completely before using the equipment Keep these instructions in a safe place Heed all warnings Follow all instructions Do not use this equipment near water Warning To reduce the risk of fire or electric shock do not expose this a
53. he optimum mode The AUTO operation may not work well at some signals In such a case it might be good to select a suitable mode except AUTO VIDEO NR ViewSonic PJ658 32 INPUT Menu continued Item Description Using the buttons A V switches the function of COMPONENT VIDEO port COMPONENT amp SCART RGB COMPONENT When the SCART RGB is selected the COMPONENT VIDEO port function as a port for a SCART RGB signal input and VIDEO port function as a port for SCART RGB sync input A SCART adapter and SCART cable realize a SCART RGB input to the projector For details contact your dealer VIDEO FORMAT Set the video format for the s video port and video port 1 Use the lt gt buttons to select the input port VIDEO FORMAT 2 Using the buttons A switches the mode S VIDEO VIDEO for video format AUTO amp NTSC amp PAL amp SECAM ft N PAL amp M PAL NTSC4 43 4 This item is performed only for a video signal from the VIDEO port or the S VIDEO port The AUTO mode automatically selects the optimum mode The AUTO operation may not work well for some signals If the picture becomes unstable ex an irregular picture a color lack please select the mode depending on the input signal FRAME LOCK Using the buttons A V turns the frame lock function on off TURN ON amp TURN OFF This item performs only at a RGB signal with vertical frequency of 50 to 60 Hz When the
54. ic For additional information or the name of the nearest ViewSonic service center contact ViewSonic 5 For applicable models with the PIN code security feature only This projector contains a personal identification number PIN that restricts access to authorized users If you forget to record the PIN code in the User Guide with your Serial Number you will have to send in the unit for service so the code can be reset However if you register your product serial number with ViewSonic along with your PIN code it will be retained on file with your registration should you need it in the future Limitation of implied warranties There are no warranties express or implied which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose Exclusion of damages ViewSonic s liability is limited to the cost of repair or replacement of the product ViewSonic shall not be liable for 1 Damage to other property caused by any defects in the product damaged based upon inconvenience loss of use of the product loss of time loss of profits loss of business opportunity loss of goodwill interference with business relationships or other commercil loss even if advised of the possibility of such damages 2 Any other damages whether incidental consequential or otherwise 3 Any claim against the customer by other party Effect of state law This warranty gives you specific l
55. io port for the RGB IN1 port however it is possible to AUDIO IN3 L R port change the settings In the default setting the AU DIO IN3 L R port is the audio port for the VIDEO S VIDEO RGB IN1 port and COMPONENT VIDEO ports however it is possible to Restart switch change the settings RGB IN2 port RGB OUT port COMPONENT VIDEO rt AUDIO IN3 pan Boy E egmb dgs dij AUDIO OUT port C RGB IN1 RGB IN2 RGB OUT AUDIO OUT CB PB ai auno IN1 CR PR Oo amom g 3 VIDEO 1 UBB VIDEO port suoeo f Bose S VIDEO port USB port AUDIO IN2 port In the default setting the AUDIO CONTROL port IN2 port is the audio port for the RGB IN2 port however it is pos Kensington lock slot sible to change the settings NOTE About Restart switch This projector is controlled by an internal microprocessor Under certain exceptional circumstances the projector may not operate correctly and the microprocessor will need to be reset In such a case please push the Restart switch by using a cocktail stick or similar and before turning on again make the projector cool down at least 10 minutes without operating Only push the Restart switch in these exceptional instances ViewSonic PJ658 5 Control buttons idu LAMP indicator TEMP indicator Cursor buttons Teme A V 4 POWER POWER indicator STANDBY ON button S ANDBY ON FN INPUT N A CY INPUT button Remo
56. lable only when the AUTO mode is selected to the VID EO FORMAT item in the INPUT menu For a component video signal the signal type is identified automatically independently of this function O For a video signal s video signal or component video signal The vertical position horizontal position and aspect ratio will be automatically set to default O For a component video signal The horizontal phase will be automatically set to default e The automatic adjustment operation requires about 10 seconds Also please note that it may not function correctly with some input Adjusting the position Olo olo 1 Press the POSITION button on the remote control S Ar Toy The POSITION indication will appear on the screen OG 2 Use the cursor buttons A lt gt to adjust the picture posi S tion GAN When you want to reset the operation press the RESET button on the remote control during the operation To complete this operation press the POSITION button again Even if you don t do anything the dialog will automatically disappear after a few seconds e When this function is performed at a video signal a certain extra such as a line may appear outside a picture ViewSonic PJ658 20 Correcting the keystone distortions Press the KEYSTONE button on the remote control A dialog ls will appear on the screen to aid you in cor SSUE OO OK recting the distortion BL E old OO 2 Use the cursor buttons A V to sele
57. lected before the operation RGB IN 1 gt RGB IN 2 gt COMPONENT VIDEO gt S VIDEO gt VIDEO Selecting an aspect ratio 1 Press the ASPECT button on the remote control Each time you press the button the projector switches the mode for aspect ratio in turn O For an RGB signal NORMAL gt 4 3 gt 16 9 gt SMALL Mo O For a video signal s video signal or component video signal 4 3 gt 16 9 gt 14 9 gt SMALL ql ll O For a no signal 4 3 fixed e The NORMAL mode keeps the original aspect ratio of the signal e Performing the automatic adjustment initializes the aspect ratio setting Adjusting the zoom and focus Zoom ring Focus ring u 1 Use the zoom ring to adjust the screen size III EZ 2 Use the focus ring to focus the picture ViewSonic PJ658 19 Using the automatic adjustment feature 1 Press the AUTO button on the remote control el O For an RGB signal OOO O The vertical position the horizontal position the horizontal phase and the horizontal size will be automatically adjusted MASAA And the aspect ratio will be automatically set to default Make sure that the application window is set to its maximum size prior to attempting to use this feature A dark picture may still be incorrectly adjusted Use a bright picture when adjusting O For a video signal or s video signal The video format best suited for the respective input signal will be selected automatically This function is avai
58. lly This function is not available while the lamp is warming up the POWER indicator flashes green and while adjusting the volume and display correcting for trapezoidal distortion zooming in on the screen using the BLANK function or displaying the menu Screen USB mouse and keyboard control 1 Connect the projector s USB port to the computer via the mouse cable Available function Remote control operation Move pointer Use A V 4 buttons Left click with mouse Press ENTER button Right click with mouse Press RESET button Press keyboard s HOME key Press HOME button ViewSonic PJ658 23 Multifunctional settings Using the menu function This projector has the following menus PICTURE IMAGE INPUT SETUP SCREEN OPTION and EASY MENU EASY MENU consists of functions often used and the other menus are classified into each purpose Each of these menus is operated using the same methods The basic operations of these menus are as follows MENU button ENTER button Cursor buttons RESET button jii Press the MENU button on the remote control or one of the cursor buttons on the projector The Advanced MENU or EASY MENU will appear In the EASY MENU 2 If you want to change it to the Advanced MENU select the Go to Advanced Menu EASY MENU RGB1 SETUP SCREEN OPTION EASY MENU MY MEMORY SAVE 1 3 Use the cursor buttons A Y to select an it
59. n the air filter cleaning message will not appear Please check and clean the air filter periodically even if there is no message If the air filter becomes to be blocked by dust or others the internal temperature will rise which could cause malfunction or reduce the lifetime of the projector It is recommended to choose 100h in general Please be careful with the operating environment of the projector and the condition of the air filter especially when the 200h 300h or TURN OFF is chosen KEY LOCK Using the buttons A V turns on off the key lock feature When TURN ON is selected the buttons on the projector except the STANDBY ON button are locked TURN ON amp TURN OFF Please use to avoid a mischief and touching accidentally This function does not have any effect on the remote control ViewSonic PJ658 42 OPTION Menu continued Item Description REMOTE FREQ Use the A Y button to change the Projector s remote sensor set ting 1 NORMAL amp 2 HIGH Items with a checkmark are on The factory default setting is for both 1 NORMAL and 2 HIGH to be on If the remote control does not function correctly set the this to either only 1 or only 2 as de Scribed in Remote Control Settings Neither can be turned off at the same time INFORMATION Selecting this item displays a dialog titled INPUT INFORMATION It shows the information about the current input 4 INPUT INFORMATION 4 INPUT INFORMATI
60. nu will close If necessary repeat the process from 3 1 1 con Ense Afterwards anytime the projector is restarted after the power switch is turned off the PIN BOX will be displayed Enter the registered PIN Code N BOX The projector can be used after entering the regis tered PIN Code If an incorrect PIN Code is input the PIN BOX will be displayed again If an incorrect PIN Code is input 3 times the projector will turn off Afterwards the projector will turn off every time an incorrect PIN Code is input The pro jector will also turn off if there is no key input for about 5 minutes while the PIN BOX is displayed This function will activate only when the projector is started after the power SECURITY switch was turned off NOTE Please do not forget your PIN Code 3 2 Turning Off the PIN LOCK Function 3 2 1 Follow the procedure in 3 1 1 to display the PIN LOCK on off menu Use the A buttons to select TURN OFF and the PIN BOX will be displayed Enter the registered PIN Code to turn the PIN LOCK function off If an incorrect PASSWORD is entered the menu will close 3 3 If you have forgotten your PIN Code PIN BOX 3 3 1 While the PIN BOX is displayed press and nahe ine Code hold the RESET button for three seconds The 10 digit Inquiring Code will be displayed NOTE If there is no key input for about 5 minutes le while the Inquiring Code is displayed the projector will turn off 3 3 2 Contact you
61. ojector be sure to activate the laptop s RGB external image output set the laptop to CRT display or to simultaneous LCD and CRT display For details on how this is done please refer to the instruction manual of the corresponding laptop computer Secure the screws on the connectors and tighten Some computers may have multiple display screen modes Use of some of these modes will not be possible with this projector For some RGB signal modes the optional Mac adapter is necessary When the image resolution is changed on a computer depending on an input automatic adjustment function may take some time and may not be completed In this case you may not be able to see a check box to select Yes No for the new resolution on Windows Then the resolution will go back to the original It might be recommended to use other CRT or LCD monitors to change the resolution About Plug and Play capability Plug and Play is a system composed of the computer its operating system and peripheral equipment i e display devices This projector is compatible with VESA DDC 2B Plug and Play can be achieved by connecting this projector to a computer is VESA DDC display data channel compatible Please take advantage of this function by connecting the accessory RGB cable to the RGB IN1 port DDC 2B compatible Plug and Play may not work properly if any other type of connection is attempted Please use the standard drivers in your computer as this pr
62. ojector is a Plug and Play monitor ViewSonic PJ658 11 Examples of connection with a computer In the default setting the AUDIO IN1 port is the audio port for the RGB IN1 and the AUDIO IN2 port is the audio port for the RGB IN2 ports To change the settings refer to the AUDIO item in the SETUP menu RGB cable USB cable E aa ua TT LH Ps is 39 i RGB out Audio out RS 232C USB 5 Ep E t t VIDEO use i 5 svinco iR x RS 232C cable Stereo mini audio cable Stereo mini audio cable 94 m Audio out AUDIO IN a gt BOUT AUDIO OUT AUDIO IN1 T UDIO IN2 gt RGB cable Connecting to a monitor output m ee ciu Ir In lo RGB IN1 RGB IN2 Rif AUDIO OUT 1 i AUDIO IN2 ees vipEo UB38uU RGB cable S VIDEO Connecting to a speaker with amplifier output AUDIO IN3 Audio in ee quoq E RGB IN2 RGB OUT AUDD OUT a A AUDIO IN1 1 mm a AUDIO IN2 y cu O CONTROL VIDEO gt us seo
63. on Detector is on KEYSTONE Using the buttons A V corrects the keystone distortion Upper in the data Lower in the data The adjustable range of this function will vary with the type of input signal At some signals this function may not work well This function will be unavailable when Transition Detector is on WHISPER Using the buttons A V turns off on the whisper mode NORMAL amp WHISPER When the WHISPER is selected acoustic noise and screen bright ness are reduced ViewSonic PJ658 35 SETUP Menu continued Description Using the buttons A V switches the mode for mirror status d A d amp MIRROR ENS H INVERT V INVERT H amp V did n If Sen Detector is TURN ON and MIRROR Sms is changed Transition Detector Alarm will be displayed when projector is re started after the power switch is turned off Using the buttons A V adjusts the volume High amp Low Allocates the audio ports Choose a picture input port using the buttons A F 1 then select the audio port to be in terlocked with the input port using the buttons lt P gt 2 When off is selected all audio ports do not work for the input port 1 RGB1 RGB2 amp COMPONENT amp S VIDEO amp VIDEO 2 182830 VOLUME ViewSonic PJ658 36 SOREN Menu With the SCREEN menu the items shown in the table be PICTURE LANGUAGE ENGLISH low can be performed IMAGE MENU POSITION INPUT
64. ons lt gt switches the mode for mirror status See the MIRROR item in the SETUP menu If Transition Detector is TURN ON and MIRROR status is changed Transition Detector Alarm will be displayed when projector is re started after the power switch is turned off Performing this item resets all of the items of EASY MENU except FILTER TIME and LANGUAGE A dialog is displayed for confirmation Selecting RESET using the button A performs resetting FILTER TIME Performing this item resets the filter timer which counts usage time of the air filter A dialog is displayed for confirmation Selecting RESET using the button A performs resetting See the FILTER TIME item in the OPTION menu LANGUAGE Using the buttons lt gt selects the LANGUAGE item to toggle the menu language Refer to description of LANGUAGE in the SCREEN menu Go to Advanced Menu ViewSonic PJ658 Select Go to Advanced Menu and press the button or the EN TER button to use the menu of PICTURE IMAGE INPUT SETUP SCREEN or OPTION 26 PICTURE Menu With the PICTURE menu the items shown in the table be low can be performed Select an item using the cursor buttons A on the projector or remote control and press the cursor button gt on the projector or remote control or the ENTER button on the remote control to execute the item Then perform it referring to the following table SELECT BRIGHTNESS 0 CONTRAST
65. ot place the projector in direct sunlight or near a hot object such as a heater Put nothing about lens and vents of the projector Put nothing on the projector Put nothing that is sucked or sticks to the bottom of projector This projector has some intake vents also on the bottom gt Do not place the projector on the place that gets wet Damping the projector or inserting liquid in the projector could cause a fire an electric shock and or malfunction to the projector Do not place the projector in a bathroom or the outdoors Put nothing containing the liquid near the projector ACAUTION P Avoid a smoky humid or dusty place Placing the projector in such place could cause a fire an electric shock and or malfunction to the pro jector Do not place the projector near a humidifier a smoking space or a kitchen gt Adjust the direction of the projector to keep the light from directly hitting the projector s remote sensor ViewSonic PJ658 Refer to the illustrations and tables below to determine the screen size and projection distance The values shown in the table are calculated for a full size screen 1024x768 a The screen size diagonal Arrangement I1 1 1 1 1 1 1 1 lt I lt I1SI lt SIS oIcoIo ls 2 o o S S NX amp m e e zx izlio e r i9e wS se E g S ge gejgpmrejej iz ic c o 5 s ol lI li lelelelioeo xielixl e e ES Sje eN EJ 2 S 2 S
66. performing press the RESET or ESC button on the re mote control Using the buttons lt P A adjusts the frame position Please move the frame to the position of the picture which you want to use The frame may not be able to be moved for some input signals To start registration press the ENTER button on the remote con trol To restore the screen and return to the previous dialog press the RESET or ESC button on the remote control Registration takes several minutes When the registration is com pleted the registered screen and the message MyScreen registra tion is finished are displayed for several seconds If the registra tion failed the message A capturing error has occurred Please try again is displayed This function will be unavailable when MyScreen Password in the Security Menu is on NOTE The KEYSTONE cannot be adjusted while using the MyScreen function MyScreen Lock Using the buttons A turns on off the MyScreen lock function TURN ON amp TURN OFF When the TURN ON is selected the item MyScreen is locked Use this function for protecting the current MyScreen This function will be unavailable when MyScreen Password in the Security Menu is on ViewSonic PJ658 38 SCREEN Menu continued Description Using the buttons A V turns on off the message function TURN ON amp TURN OFF When the TURN ON is selected the following message function works AUTO IN PROGRESS
67. pparatus to rain or moisture Clean with a soft dry cloth If further cleaning is required see Cleaning the Display in this guide for further instructions Do not block any ventilation openings Install the equipment in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other devices including amplifiers that produce heat Do not attempt to circumvent the safety provisions of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade and the third prong are provided for your safety If the plug does not fit into your outlet consult an electrician for replacement of the outlet Protect the power cord from being tread upon or pinched particularly at the plug and the point where if emerges from the equipment Be sure that the power outlet is located near the equipment so that it is easily accessible Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the equipment When a cart is used use caution when moving the cart equipment combination to avoid injury from tipping over Unplug this equipment when it will be unused for long periods of time Refer all servicing to qualified service personnel Service is required when th
68. prior written permission from ViewSonic Corporation Product Registration To meet your future needs and to receive any additional product information as it becomes available please register your product on the Internet at www viewsonic com The ViewSonic Wizard CD ROM also provides an opportunity for you to print the registration form which you may mail or fax to ViewSonic For Your Records Product Name PJ658 ViewSonic LCD Projector Model Number VS11361 Document Number PJ658 1_UG_ENG Rev 1C 06 20 06 Serial Number Purchase Date Personal Identification Number PIN N The lamp in this product contains mercury Please dispose of in accordance with local state or federal laws ViewSonic PJ658 iii Projector PJ658 Users Manual Operating Guide Contents of package 1 Projector 2 Remote control with two AA batteries 3 Power cord 4 RGB cable 5 Audio Video cable 6 Soft case 7 Quick Start Guide and ViewSonic Wizard CD 8 Lens cover Rivet and Strap NOTE Keep the original packing materials for future reshipment For moving the projector be sure to use the original packing materials Use special caution for the lens part NUN MEMEL Various symbols are used in this manual The meanings of these symbols are described below AWARNING This symbol indicates information that if ignored could possibly result in personal injury or even death due to incorrect handling ACAUTION This s
69. r dealer with the 10 digit Inquiring Code Your PASSWORD will be sent after your user registration information is confirmed ViewSonic PJ658 47 OPTION Menu continued Item Description 4 Using the Transition Detector Function While the Transition Detector function is ON when power switch is started to supply to the projector it might react as below Transition Detector alarm shown below might appear on screen if the pro jector has been moved or re installed Transition Detector alarm might appear on screen if the MIRROR setting has been changed Keystone adjustment feature has been prohibited as long as the Transition Detector function is ON 4 1 Turning On the Transition Detector Function 4 1 1 Use the A Y buttons on the SECURITY menu to select Transition Detector and press the or the 4 Transition Detector ENTER button to display the Transition Detector FEGEN on off menu Select TURN ON and the current angle mirror and keystone setting will be recorded NOTE This feature may not function properly if the projector Transition Detector is not in a stable position when TURN ON is selected on off menu 4 1 2 If this function is set to TURN ON when the lt lt TRANSITION DETECTOR 0N gt gt vertical angle of the projector mirror or key ha rojector ha Ich tated stone setting at which the projector is turned visae eda armia laces on is different than the previously recorded the Sleds Tee ee acta T
70. r off and allow the projector to cool down at least 20 minutes After the projector has Turned Blinking sufficiently cooled down please make confirmation off In Red that no foreign matter has become caught in the fan etc and then turn the power on again If the same indication is displayed after the remedy please contact your dealer or service company There is a possibility that the interior portion has become heated Please turn the power off and allow the projector to cool down at least 20 minutes After the projector has sufficiently cooled down please make confirmation of Turned Lighting the following items and then turn the power on again off In Red Is there blockage of the air passage aperture s the air filter dirty Does the peripheral temperature exceed 35 C If the same indication is displayed after the remedy please set FAN SPEED of the SERVICE item in the OPTION menu to HIGH It is time to clean the air filter Please immediately turn the power off and clean or Lighting Simultaneous change the air filter referring to the section Air Filter In Green blinking in Red After cleaning or changing the air filter please be sure to reset the filter timer After the remedy reset the power to ON There is a possibility that the interior portion has become overcooled Please use the unit within the usage temperature pa rameters 5 C to 35 C After the treatment reset the power to
71. ransition Detector Alarm will be displayed and the projector will not display the input signal Transition Detector Alarm Either set the Transition Detector off in the SECURITY menu or set the projector at the recorded angle mirror and keystone setting to display the input signal SECURITY If the Transition Detector ALARM is displayed for about 5 minutes the lamp will turn off This function will activate only when the projector is started after the power switch was turned off 4 2 Setting the Transition Detector PASSWORD 4 2 1 Use the A buttons on the SECURITY menu to select Transition Detector and press the or the ENTER button to display the Transition Detector on off menu 4 2 2 Use the A V buttons on the Transition Detector on off menu to select TURN ON The ENTER Transition Detector ENTER PASSWORD A 0000 NZ PASSWORD BOX small will be displayed 4 2 3 Use the A lt gt buttons to enter a PASSWORD Move the cursor to the right side of the ENTER PASSWORD BOX small and press the button to display the CHECK PASSWORD BOX enter the same PASSWORD again 4 2 4 Move the cursor to the right side of the CHECK PASSWORD BOX and press the button to display the PASSWORD for about 20 seconds please make note of the PASSWORD during this time After the PASSWORD has displayed for about 20 seconds the screen will return to the Transition Detector on off menu QUIT NEXT ENTER PASSWORD BOX small
72. rrect PASSWORD is input the menu will close If necessary repeat the process from 2 3 1 2 4 If you have forgotten your PASSWORD 2 4 1 Follow the procedure in 2 1 1 to display the MyScreen PASSWORD on off menu 2 4 2 Select TURN OFF to display the ENTER EL Um PASSWORD BOX large The 10 digit Inquir inquiring Code ing Code will be displayed inside the BOX 0123456789 QUIT ENTER PASSWORD BOX large 2 4 3 Contact your dealer with the 10 digit Inquir ing Code Your PASSWORD will be sent after your user registration information is confirmed 3 Using the PIN LOCK Function PIN LOCK is a function which prevents the projector from being used unless a registered Code is input 3 1 Registering the PIN Code PIN LO 3 1 1 Use the A buttons on the SECURITY menu ERCEN to select PIN LOCK and press the button or the ENTER button to display the PIN LOCK on off menu PIN LOCK on off 3 1 2 Use the amp buttons on the PIN LOCK on off ding menu to select TURN ON and the PIN BOX will be displayed ViewSonic PJ658 46 OPTION Menu continued Item Description 3 1 3 Input a 4 part PIN Code using the A lt gt RGB and INPUT buttons PIN BOX A CONFIRMATION BOX will appear Reenter the Input PIN Code same PIN Code This will complete the PIN Code EJNESBESBEZNCEJYE registration PIN BOX NOTE If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the me
73. sentation impressive O Compact Body Even with its many features this projector is extremely compact and slim which gives you more flexibility and usability to use it where you want About contents of package Please see the Contents of package of the User s Manual Quick Guide Your projector should come with the items shown there Contact immediately your deal er if anything is missing NOTE Keep the original packing materials for future reshipment For moving the projector be sure to use the original packing materials Use special caution for the lens part Fastening the lens cover To avoid losing the lens cover please fasten it the lens cap to the projector using the strap 7 Strap ring L 1 Fix the strap to the strap ring of the lens cover Strap hole 2 Put the strap into the groove on the rivet 3 Push the rivet into the strap hole ViewSonic PJ658 3 PPartemames Projector z Control buttons as ae a s Lamp cover EA Lamp unit is inside S s 2282 Remote sensor Speaker Zoom ring Focus ring Security bar Use for attaching a com mercial anti theft chain or Vent wire Elevator button Elevator foot Filter cover Air filter and intake vent are inside Bottom side ViewSonic PJ658 Qe switch AC inlet Ports See below Elevator button Elevator foot Rear Left side Vent AUDIO IN1 port In the default setting the AUDIO IN1 port is the aud
74. sor button gt on the projector or remote control or the ENTER button on the remote control to execute the item Then perform it referring to the following table PROGRESSIVE TV VIDEO NR MID COLOR SPACE AUTO COMPONENT COMPONENT VIDEO FORMAT AUTO FRAME LOCK TURN ON RGB IN RESOLUTION Item Description Using the buttons A switches the progress mode TV FILM TURN OFF This function is performed only for an interlaced signal of a VIDEO input an S VIDEO input or COMPONENT VIDEO input of 525i 480i When TV or FILM is selected the screen image will be sharp FILM adapts to the 2 3 Pull Down conversion system But these may cause a certain defect for example jagged line of the picture for a quick moving object In such a case please select TURN OFF even though the screen image may lose the sharpness Using the buttons A V switches the noise reduction mode HIGH amp MID amp LOW This function performs only at a VIDEO input an S VIDEO or COMPONENT VIDEO input of 525i 480i or 625i 576i signal When this function is excessive it may cause a certain degrada tion of the picture Using the buttons A V switches the mode for color space AUTO RGB SMPTE240 amp REC709 amp REC601 ft 5r This item can be selected only for an RGB signal or a component COLOR SPACE video signal except signals of SCART RGB from the component video port The AUTO mode automatically selects t
75. t 3 times the projector will turn off After wards the projector will turn off every time an incorrect PASSWORD is input 1 2 Changing the PASSWORD 1 2 1 Use the A Y buttons on the SECURITY menu to select SECURITY PASSWORD CHANGE and press the button to display the ENTER NEW PASSWORD BOX 1 2 2 Use the A V 4 buttons to enter the new PASSWORD 1 2 3 Move the cursor to the right side of the EN TER NEW PASSWORD BOX and press the gt button to display the NEW PASSWORD AGAIN BOX enter the same PASSWORD again 1 2 4 Move the cursor to the right side of the NEW PASSWORD AGAIN BOX and press the gt button and the NOTE NEW PASSWORD BOX will be displayed for about 20 seconds please make note of the PASSWORD during this time Pressing the ENTER button on the re mote controll or INPUT button on the projector will close the NOTE NEW PASSWORD BOX NOTE Please do not forget your PASSWORD This projector is equipped with security functions User registration is required before using the security functions SECURITY ENTER PASSWORD a 0000 v QUIT NEXT ENTER PASSWORD BOX SECURITY PASSWORD CHANGE MyScreen PASSWORD TURN OFF TRANSITION DETECTOR TURN OFF SECURITY MENU SECURITY ENTER NEW PASSWORD ENTER NEW PASSWORD BOX SECURITY NEW PASSWORD AGAIN NEW PASSWORD AGAIN BOX SECURITY NOTE NEW PASSWORD 0000 ENTER EXIT NOTE NEW PASS WORD BOX ViewSonic PJ658
76. t the horizontal and vertical 4 INFORMATION positions clock phase and horizontal size RGB1 and automatically select an aspect ratio The 1280x 768 60 INFORMATION dialog will be displayed 4 To set a custom resolution use the A V RESOLUTION buttons to select CUSTOM and the CUSTOM CUSTOM RESOLUTION 2 RESOLUTION BOX will be displayed Set the horizontal HORZ and vertical VERT resolutions using the A W lt gt buttons 1 5 To save the setting place the cursor on the right most digit and press the button The horizontal and vertical positions clock phase and horizontal size will be automati cally adjusted and an aspect ratio will be automatically selected After the INFORMATION dialog has displayed for about 10 seconds the screen will return to the RESOLUTION menu displaying the changed resolution 6 To revert back to the previous resolution without saving changes place the cursor on the left most digit and press the lt button HORZ x VERT 40992 x 0744 NZ QUIT SET CUSTOM RESOLUTION BOX 4 INFORMATION RGB1 992x 744 60 STANDARD O 1024x 768 1280x 768 1360x 768 The screen will then return to the RESOLUTION menu displaying the previ ous resolution 1 Not all resolutions are guaranteed 2 For some pictures this function may not work well ViewSonic PJ658 34 SEINUPR Menu With the SETUP menu the items shown in the table below can be performed
77. te control SEARCH button STANDBY ON button RGB button Cs amp SEARCH AUTO button VIDEO button es 5 a AUTO BLANK button ASPECT button O PAGE UP button HOME button je HOME PAGE UP OIO de VOLUME button MAGNIFY 2 END PAGEDOUN le ON button COO OO MUTE button OFF button gms PAGE DOWN button END button KEYSTONE button FREEZE button MY BUTTON button POSITION button MENU button ESC button Cursor buttons rs A Vd gt ENTER button RESET button Battery cover on the back ViewSonic PJ658 Seid ore NUT AWARNING Place the projector in a stable position horizontally A fall or a turnover could cause an injury and or damage to the projector Then using damaged projector could result in a fire and or an electric shock Do not place the projector on an unstable slant or vibrant surface such as a wobbly or inclined stand Do not place the projector in the side front rear up position except cleaning the air filter Place the projector in a cool place and pay attention enough to ventilation The high temperature of the projector could cause a fire a burn and or malfunc tion to the projector Do not stop up block and cover the projector s vents Keep a space of 30 cm or more between the sides and other objects such as walls Do not place the projector on a metallic thing or anything weak in heat Do not place the projector on a carpet cushion or bedding Do n
78. the vertical position to the V POSITION default setting Pressing the RESET button when V POSITION is selected will reset the V POSITION to the default setting For a video signal s video signal or component video signal The adjustable range of V POSITION depends on the OVERSCAN setting It is not possible to adjust when the OVERSCAN is set to 10 Using the buttons A adjusts the horizontal position Left amp Right Over adjusting the horizontal position may cause noise to appear on the screen If this occurs please reset the horizontal position to H POSITION the default setting Pressing the RESET button when H POSITION is selected will reset the H POSITION to the default setting For a video signal s video signal or component video signal The adjustable range of H POSITION depends on the OVERSCAN setting It is not possible to adjust when the OVERSCAN is set to 10 Using the buttons A adjusts the horizontal phase to eliminate flicker H PHASE Right amp Left This item can be selected only for an RGB signal or a component video signal ViewSonic PJ658 30 IMAGE Menu continued Description Using the buttons A adjusts the horizontal size Large amp Small This item can be selected only for an RGB signal When this adjustment is excessive the picture may not be dis played correctly In such a case please reset the adjustment by pressing the RESET button on the remote
79. trol user specified settings are saved for about half a day If the batteries are removed from the remote control for longer than half a day the remote will reset to Setting 1 Changing the signal setting for the projector s remote sensor Switch between Setting 1 and 2 using the SERVICE REMOTE FREQ item found in OP TION MENU If the remote control does not seem to function properly try changing the settings for the remote control and the projector s remote sensor The remote control will not function properly if the remote control transmitter settings and the projector s remote sensor settings are not the same The remote control works with the projector s remote sensor P m e C approx 3 meters 7 30 E T _ UY U The range of the remote sensor is 3 meters with a 60 degree range 30 degrees to the left and right of the remote sensor Also a remote signal reflected in the screen etc may be available If it is difficult to send a remote signal to the sensor directly please try to use the reflected signal Since the remote control uses infrared light to send signals to the projector Class1 LED be sure to use the remote control in an area free from obstacles that could block the re mote control s output signal to the projector ViewSonic PJ658 16 Turning on the power c fi DBY ON POWER Make sure that the power cord is firmly and cor nM D indicator rectly connected to the projector and the outlet
80. ure mercury glass lamp The lamp can break with a loud bang or burn out if jolted or scratched handled while hot or worn over time Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them In addition when the bulb bursts it is possible for shards of glass to fly into the lamp housing and for gas containing mercury to escape from the projector s vent holes gt About disposal of a lamp This product contains a mercury lamp do not put it in a trash Dispose of it in accordance with environmental laws For lamp recycling go to www lamprecycle org in the US For product disposal contact your local government agency or www eiae org in the US or www epsc ca in Canada For more information call your dealer If the lamp should break it will make a loud bang when it does unplug the power cord from the outlet and make sure to request a replacement lamp from your local dealer Note that shards of glass could damage the inside of the projector or cause injury during handling so please do not try Disconnect to clean the projector or replace the lamp yourself theplug If the lamp should break it will make a loud bang when it does ventilate fromthe the room well and make sure not to breathe the gas that comes out of the pel projector vents or get it in your eyes or mouth Before replacing the lamp turn the projector off and unplug the power cord then wait at least
81. utting batteries 15 Using the remote control 16 Power on off 17 Turning on the power 17 Turning off the power 17 Operating 18 Adjusting the volume 18 Temporarily muting the sound 18 Selecting an input signal 18 Searching an input signal 19 Selecting an aspect ratio 19 Adjusting the zoom and focus 19 Using the automatic adjustment feature 20 Adjusting the position Correcting the keystone distortions 21 Using the magnify feature 21 Freezing the screen 22 Temporarily blanking the screen 22 Operating the computer screen 23 Multifunctional settings 24 Using the menu function 24 EASY Menu 00 ViewSonic PJ658 Aspect Auto keystone Execute Key stone Picture mode Brightness Con trast Color Tint Sharpness Whisper Mirror Reset Filter time Language Go to advanced menu PICTURE Menu 27 Brightness Contrast Gamma Col or temp Color Tint Sharpness My memory IMAGE Menu 30 Aspect Over scan V position H position H phase H size Auto adjust execute INPUT Menu 32 Progressive Video NR Color space Component Video format Frame lock RGB in Resolution SETUP Menu 35 Auto keystone Execute Keystone Whis per Mirror Volume Audio SCREEN Menu 37 Language Menu position Blank
82. what warranty condition is applied Specifications NOTE These specifications are subject to change without notice Item Specification Product name Liquid crystal projector Liquid Panel size 1 6 cm 0 63 type Crystal Drive system TFT active matrix panel Pixels 786 432 pixels 1024 horizontal x 768 vertical Lens Zoom lens F 1 7 1 9 f 18 9 22 6 mm Lamp 200W UHB Speaker 1W x 1 Power Supply AC100 120V 3 3A AC220 240V 1 4A Power Consumption 310W Temperature range 5 35 C Operating 306 W x 83 H x 249 D mm Size Not including protruding parts Please refer to the following figure Weight mass 3 0 kg RGB input Audio output RGB IN1 D sub 15pin mini x1 AUDIO OUT Stereo mini x1 RGB IN2 D sub 15pin mini x1 Video input RGB output COMPONENT VIDEO Ports RGB OUT D sub 15pin mini x1 Y CB PB CR PR RCA x3 Audio input S Video Mini DIN x1 AUDIO 1 Stereo mini x1 Video RCA x1 AUDIO 2 Stereo mini x1 Communication port AUDIO 3 RCAx2 CONTROL D sub 9pin x1 USB ee USB B x1 Lamp RLC 017 we Air filter Please consult your dealer Others Please consult your dealer ViewSonic PJ658 61 Specifications continued ll 249 mm
83. while automatically adjusting NO INPUT IS DETECTED SYNC IS OUT OF RANGE Searching while searching for the input MESSAGE Detecting while an input signal is detected The indication of the input signal displayed by changing The indication of the aspect ration displayed by changing The indication of the My Memory displayed by changing The indication of the Picture Mode displayed by changing The indication of FREEZE and Il while freezing the screen by pressing the FREEZE button When the TURN OFF is selected please remember if the picture is freezing Do not mistake freezing for a malfunction Each input port for this projector can have a name applied to it 1 Use the A V buttons on the SCREEN 4 SOURCE NAME menu to select SOURCE NAME and press C NB N the gt button The SOURCE NAME menu RGB2 DESKTOP PC will be displayed COMPONENT DVD S VIDEO CAMERA 2 Use the A V buttons on the SCREEN VIDEO VIR NAME menu to select the port to be named and press the button The SOURCE Poi UND NAME dialog will be displayed until a name is specified 3 The current name will be displayed on IUE UH the first line Use the A V and EN RGBI TER or INPUT buttons to select and enter ar LACK characters The RESET button can be used to erase 1 character at a time The name SOURCE NAME can be a maximum of 16 characters 4 To change an already inserted charac ter press the A button while the cursor is
84. wsonic com ViewSonic PJ658 63 Limited Warranty ViewSonic Projector What the warranty covers ViewSonic warrants its products to be free from defects in material and workmanship during the warranty period If a product proves to be defective in material or workmanship during the warranty period ViewSonic will at its sole option repair or replace the product with a like product Replacement product or parts may include remanufactured or refurbished parts or components How long the warranty is effective North and South America Three 3 years warranty for all parts excluding the lamp three 3 years for labor and one I year for the original lamp from the date of the first consumer purchase Europe except Poland Three 3 years warranty for all parts excluding the lamp three 3 years for labor and ninety 90 days for the original lamp from the date of the first consumer purchase Poland Two 2 years warranty for all parts excluding the lamp two 2 years for labor and ninety 90 days for the original lamp from the date of the first consumer purchase Other regions or countries Please check with your local dealer or local ViewSonic office for the warranty information Lamp warranty subject to terms and conditions verification and approval Applies to manufacturer s installed lamp only AII accessory lamps purchased separately are warranted for 90 days Who the warranty protects This warranty is valid only for the first
85. ymbol indicates information that if ignored could possibly result in personal injury or physical damage due to incorrect han dling Please refer to the pages written following this symbol NOTE The information in this manual is subject to change without notice The manufacturer assumes no responsibility for any errors that may appear in this manual The reproduction transfer or copy of all or any part of this document is not permitted without express written consent Trademark acknowledgment VGA and XGA are registered trademarks of International Business Machines Corporation Apple and Mac are registered trademarks of Apple Computer Inc VESA and SVGA are trademarks of Video Electronics Standard Association Windows is a registered trademark of Microsoft Corporation All other trademarks are the properties of their respective owners ViewSonic PJ658 1 About this manual 1 Content 2 Projector features 3 Preparations 3 About contents of package 3 Fastening the lens cover 3 Part names 4 Projector 2 2222222220 4 Control buttons 6 Remote control 6 Setting up esee 7 Arrangement 22 222222 8 Adjusting the projector s elevator 9 Using the Security Bar 10 Connecting your devices 11 Connecting power supply 14 Remote control 15 P

Viewsonic PJ658 data projector

Contents

Download Pdf Manuals

Related Search

Related Contents