Newstar FPMA-HAW100 flat panel wall mount
Contents
1. Swivel angle of Long Arm can be up to 180 degrees 180 S e Do not hold the arm as support to get up Swivel angle of Front Arm can be up to 370 degrees S Do not hang unnecessary objects on the arm Pivot upwards to 20 amp downwards to 35 20110307 E C2. then take out the cover of wall hanger Do not discard SO ae ene amp i Please insert the cable to the monitor complete the circuit and the cover of wall hanger after take it out SA A owen seen dy LS NLA then fix the cap 3 Put the wall hanger on the exact place amp height that OMe So E eae Seo omer re you want and have 4 marks on the wall the cables to go through if necessary 4 Install the wall hanger on the wall with 4 expansion bolts eUse level gauge to help the wall mount installation SOMA RC wal computerproducts www NewStar nl Phone 31 0 23 547 88 88 Assembly Guide STEP 6 LCD Monitor grab handle 1 Please insert the grab handle into the 2 holes on the bottom of universal joint 2 Then fix the grab handle with 4 screws by 2 5 mm Allen Key to the 4 holes on the lower part of universal joint ae L X L a aie i D ho n 2 X4 p XI Adjustment For Loading Caution for weight capacity adjustment 1 Make sure you have checked out the weight of the panel you wish to mount 2 Support the arm throughout during assembly 3 Pull down the arm and take out the upper cap see as below figure when adjust Adjustment Use the Allen key provided to adjust the weight capacity Twist the Allen key in a clockwise direction for more weight counterclockwise direction for less weight FPMA HAW100 1 6 kg FPMA HAW100HC 6 12 kg Safety Notes Once assembled DO NOT di
3. FPMA HAW100 FPMA HAW100HC Series Before starting Assembly STEP 2 Only keep the drawing on the assembly guide STEP 3 l l Please spend some time reading this manual then follow the simple step AROG RIOYA OA Apa me eee A a A An by step guide to assembly 1 Place the bearings onto the spindle in figure Please keep the screws in order to screw back after the monitor e Some panels are viewed differently from the exploded drawing below 2 Place the arm onto the spindle and put the end cap on it Installation are completed Then pull out the cable in order to install the this is for extra clarity 3 Make sure C clip is fitted into groove of spindle securely for monitor ar Do not discard any of the packaging until you have checked all the parts collecting the cables VQ and the pack of fittings 4 Fix the cover on the wall mount and screw the cover f you are missing any of the parts contact store where you purchased AB Check list anette r STEP 4 LCD Monitor Assembly Fix the Monitor on the VESA mount using Allen Key and screws cables M4X12 O P 2 5mm X PIA lt arrange PR Pau Pum O k Z P wou R D ZA 4mm 05 pm moss XA Qf X2 eS xX as Assembly Guide STEP 1 Wall Hanger Assemble 1 Make sure the substantial wall before assembling 2 Please take screwdriver to loosen the wall hanger oy M4x35 Oo e X4 l ZA 2 5mm X o AXA STEP 5
4. s assemble Make sure that mounting screws are suitable for the vertical surface and adequate to hold the weight of the arm and the monitor Support the monitor and arm throughout assembly and mounting Keep small parts out of the reach of children Adjusting Universal Joint Tension When assembling the arm with monitors of different weights you may find that the tension of the universal joint needs to be adjusted to ease movement or to maintain the desired monitor position If so adjust as follows Make sure that the vertical Only use with LCD TFT monitors AN surface is substantial to take the that are VESA compliant weight of the arm and monitor 75 7 5MM 100 1 00MM Screw Head Nylon nut Sollid RC wall a Remove the plastic universal joint cover O ronioce berenean b Find the nylon nut not the screw head and use the provided weigh any more than between wrench to adjust the tension Fix the screw head by wrench at the same time when adjust FPMA HAW100 1 6 kg c Use one hand to support the monitor and adjust the tension of the universal joint eClockwise more tension eCounterclockwise less tension d When the desired tension is achieved replace the plastic cover B FPIMA HAWIOOHC 6 12kg Do Not Swing on Arm Caution g eSupport the monitor during the adjustment procedure e Only adjust the nylon nut not the screw head Do not disassemble the universal joint Arm Operation
Download Pdf Manuals
Related Search