Cyrus Quattro User Guide Manual
Contents
1. Cyrus Quattro Making Recordings Selecting the source to record Select the required source for recording with the front panel Input key then set the Tape Recorder to Record CAUTION Do not select the TAPE input whilst making a recording from the Quattro a loud noise may occur due to feedback in the tape recorder Record level setting Record level where necessary should be set at the recorder The volume control of the Quattro will not affect the record level Digital recordings High quality digital recordings may be easily made from the Quattro CD player to a Digital Tape or Disc Recorder connected to the Quattro CD digital output No adjustment is necessary to the Quattro once the CD player is set to play Listening through headphones The Quattro is equipped with a standard 6 35mm headphone connector located on the rear panel When headphones are connected to the Quattro for personal listening the sound from the system speakers will automatically be muted REMOTE CONTROL Key to the remote control drawing Fig 3 25 Standby 30 Search forward reverse 26 Mute 31 Numeric keypad 27 Input select 32 Store 28 Change track 33 Play pause 29 Stop 34 Volume All front panel controls of the Cyrus Quattro feature on the remote handset The remote control handset also provides access to some additional features of the Cyrus Quattro Input source selection The Input Source keys enabl2. Pausing Press the Play Pause key to pause the current track The disc will be held at the point of interruption and the Pause symbol will show on the display Fig 4b Press the Play Pause key again to resume playing the disc Fast Forward Reverse Search You can search forward or backward to locate a specific point within a track by holding down the scan keys The search will commence initially at a slow speed increasing after a few seconds if the key is held down Stopping the disc When a disc is playing press the Stop Open Key once to stop the disc immediately If the disc is already stationary one touch of the Stop Open key will open the tray Listening to Radio only with tuner module fitted Selecting Tuner input Select the TUNER input with the front panel Input key Searching for a station Press one of the Scan keys to search for a station When a station is found the station name will be shown on the display Fig 4d If the station does not broadcast name data the station frequency will be shown Fig 4c Volume control The volume level is controlled from the front panel with the Volume up down keys Listening to an External Source Aux Tape Selecting Aux or Tape input Select the correct input with the front panel Input key Volume control The volume level is controlled from the front panel with the Volume up down keys GB Downloaded From Disc Player com Cyrus Manuals
3. MC Bus Output of the power amplifier to the MC Bus Input of the Quattro Fig 5 User Instructions OPERATION Key to the front panel drawing Fig 2 13 CD Loading Tray 19 Volume up 14 Standby Key 20 Volume down 15 Standby Light 21 Input Select 16 Remote Eye 22 Next Track 17 Display Window 23 Previous Track 18 Stop Open 24 Play Pause Switching On The mains power to the Quattro should normally be left on unless left unattended for a long period when the mains power at the wall socket should be switched off or the product disconnected from the AC supply When power is applied the front panel STANDBY key is used for power control The Standby light shows red when the Quattro is in Standby and green when operational Listening toa CD Selecting CD input Select the CD input with the front panel Input key Loading aCD Press the STOP OPEN key to open the CD tray Place a CD in the tray with the label side upward Press the STOP OPEN key again The CD tray will load into the player The Quattro display will show Reading while checking the contents of the disc Volume control The volume level is controlled from the front panel with the Volume up down keys The display will switch briefly to show the volume level setting Fig 4e Selecting a track Press the Scan keys briefly to move forward or backward through the tracks on the CD Track indications appear on the display Fig 4a
4. product service or technical advice contact only authorised Cyrus service centres The Cyrus distributors are listed at the end of this instruction manual Cyrus Quattro Welcome to the world of Cyrus Congratulations on your choice of Cyrus Hi fi products Our state of the art design technology and outstanding quality of manufacture has won countless awards around the world We are confident that you will derive great pleasure from owning a product from one of the most recognised and respected manufacturers of hi fi equipment Please read these instructions carefully before commencing installation They provide full guidance to help you install your Cyrus Quattro safely and correctly Preparations for Installation Before installing the Quattro check that the following items are included in the accessory box Warranty Card with instruction manual AC Mains Cable Remote Control Handset 2 x Phono leads for MC BUS connection After removing these items please retain the packaging Install the Quattro in a well ventilated location away from sources of high temperature dust or humidity Never stand the Quattro under another unit or on any surface likely to hamper its cooling or ventilation The Quattro System Cyrus Quattro Power amplifier Loudspeaker system As supplied the Cyrus Quattro may be connected to just a Cyrus power amplifier and a pair of speakers to provide a full featured CD playing hi fi system The first se
5. User Instructions Cyrus Quattro Cyrus Quattro SSOSOSSS 1 325 noa oc a QD nn oz zaoz P cano Fi 4 si HI a Ce gt Bi 1 Cyrus SmartPower Fig 5 Downloaded From Disc Player com Cyrus Manuals User instructions Quattro User Instructions IMPORTANT Read before operating this equipment CAUTION The exclamation mark is to draw your attention to important instructions and safety procedures in this manual ATTENTION The lightning flash warns you of the risk of electrical shock presented by components inside this AN product Unauthorised personnel must not open this unit WARNING To reduce the risk of electrical shock do not remove any unit covers or panels There are no user serviceable parts in this product WARNING To reduce the risk of electric shock do not expose this equipment to rain or moisture HEED WARNINGS All warnings on the product and in the operating instructions should be adhered to READ ALL THE INSTRUCTIONS All the safety and operating instructions should be read before the product is operated RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference FOLLOW INSTRUCTIONS All operating and use instructions should be followed CLEANING Unplug this product from the mains before cleaning Do not use liquid or ae
6. ction of these instructions provides details of setting up and operating such a system Upgrade options which may be fitted internally include e The option of the Quattro FM tuner module to add high quality radio reception The option of the Quattro Multi room kit which will in conjunction with additional power amplifiers feed three more rooms in your home with high quality sound from the main Quattro unit The wireless remote control included in the kit adds the convenience of a handset which can control the Quattro through the walls of the house Note Both the FM tuner module and the Multi room kit must be fitted internally to the Quattro by an authorised Cyrus dealer The Cyrus Quattro as a CD Tuner source Alternatively with a small internal adjustment carried out by an authorised Cyrus agent the Quattro may be connected to provide direct CD and tuner outputs to an external Cyrus integrated amplifier pre amplifier or surround decoder For such an installation refer to the section Connection and Operation of the Quattro as a CD Tuner Downloaded From Disc Player com Cyrus Manuals User Instructions INSTALLATION Key to the rear panel drawing Fig 1 1 Aerial connector 7 Multi room outputs 2 Preamp output 8 MC Bus connections 3 CD direct output 9 Multi room receiver connector 4 Tape Output 10 CD Digital output 5 Aux Input 11 Power Inlet 6 Tape Input 12 Headphone Output Connecting a Power Amp
7. during a lightning storm or when it is left unattended or unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges CAUTION POLARISED CONNECTOR CANADA and USA To prevent electrical shock match wide blade of plug to wide slot fully insert Do not alter or remove this plug if it does not fit your mains power socket Have a suitable socket installed by a competent electrician POWER SUPPLY The moulded IEC connector of the AC cord supplied plugs into the power inlet onthe rear of the unit The mains supply requirement for your Cyrus Quattro is marked on a label on the rear panel Before connecting check that this voltage is the same as your mains supply 230V Products Voltage Range 220V 240V 115V Products Voltage Range 110V 120V If you move to an area with a different mains voltage contact your local Cyrus distributor to have your product converted There are no user replaceable fuses in this unit NOTE FOR UK CUSTOMERS The Cyrus Quattro is supplied with a power cable terminated by a fused 13A mains plug This plug should not be removed but if it is removed dispose of it safely and do not re use it To connect a new 13A plug proceed as follows Connect the brown wire to the terminal marked L or coloured red Connect the blue wire to the terminal marked N or coloured black The internal pl
8. e direct access to each of the four available input sources Volume control The Volume control keys enable remote setting of volume levels Mute The Mute key will temporarily reduce the volume level to zero Press the Mute key again to restore the previous volume setting CD operation keys When a CD is playing the remote control includes keys for Track Selection Stop Fast Forward Reverse Search and Play pause Tracks can be selected directly with the numbers of the Numeric Keypad If the disc playing has more than 10 tracks the Quattro will pause briefly awaiting for the entry of a second digit where appropriate Tuner operation keys When listening to the tuner the remote control includes keys which will Step through the presets or Search the band for a station When presets stations have been stored in the memory see next section they can be selected directly with the numbers of the Numeric Keypad As each preset is selected the display will briefly show the station number and frequency before displaying the station name where available Storing preset radio stations For convenience the Quattro has nine preset memories 1 9 in which stations can be stored for quick access To store a station follow this sequence 1 Tune to a station with the Search keys 2 Press the Store key The display will read Store 3 From the Numeric Keypad press a key 1 9 for your chosen
9. e erento eae As plate on rear of unit from whom the equipment was purchased This warranty excludes Power Consumption Playing 10W e Damage caused through neglect accident misuse wear and Standby rein Annan ariel adandana 5W tear or through incorrect installation adjustment or repair by Safety Requirement un EN60065 unauthorised personnel Any unauthorised servicing will result in Enclosure loss of guarantee Dimensions WxHxD 215 x 75 x 365mm e Liability for damage or loss occurring in transit to or from the Weight ss cattec canta ee nee 3 2Kg purchaser i i e Consequential damage loss or injury arising from or in Audio Performance CD amplifier conjunction with this equipment Input sensitivity Tape AUX 200mV Equipment for attention under warranty should be consigned return Output Level pre out s 242mV carriage paid If returned equipment is found to comply with the Output Level CD direct out 2 0V published specification CYRUS reserves the right to raise a charge Output Impedance pre out 220Q Output Impedance CD direct out 100Q Frequency Response s s s Channel Separation c cccccessssscsssssessssssssesssssseneeees The above conditions do not affect your statutory rights as a consumer SNR using silent CD track SNR AUX input ref 1V o p THD CD 10dB 3 ss ananas 0 005 THD AUx input rase attente A
10. k for the pause symbol on the display Tuner module not fitted No radio stations can be found poor quality radio sound Signal strength inadequate Arrange for a better aerial No Remote Operation The handset batteries may need to Remove the battery compartment be replaced cover located underneath the unit Remove the batteries and replace with new ones carefully noting the orientation marked in the bottom of the battery case Display reads WRONG R MOTE The Quattro has been converted to operate as a CD Tuner The Audio Commander remote control supplied with Cyrus amplifiers must be used after this conversion The batteries in the remote control unit should only be replaced with new batteries type AA I E C L R06 User Instructions Cyrus Quattro Laser Product WARRANTY This label on the rear panel tells The warranty card enclosed should be completed by the Dealer and you that the unit contains a Laser CLASS 1 th h d returned to CYRUS or its Distributor within 8 d component Opening this unit will LASER PRODUCT REE ge EU area eee Pople warden M aaa of purchase No Dealer or Distributor may vary the terms of this expose the user to radiation from laser tate ca warranty which is personal to the original Purchaser and is not transferable SPECIFICATIONS Please retain the sales receipt as proof of purchase Power Supply Warranty claims must wherever possible be made through the Dealer Voltage tec eee c
11. lifier and Speakers Connect a suitable stereo phono interconnect to the Pre amp output sockets of the Quattro and the input of the power amplifier Refer to the handbook for the power amplifier for speaker connection instructions Connecting an Additional Source An additional sound source may be connected to play through the AUX input of the Quattro Suitable signal sources may include a television CD changer a music keyboard or personal computer Connect the line output of the source to the rear panel AUX input connections with a suitable phono interconnect Connecting a Cassette or Disc Recorder A cassette or disc recorder may be connected to record and play through the Quattro system Connect the line output play of the recorder to the TAPE input connections of the Quattro with a suitable phono interconnect Connect the line input record of the recorder to the rear panel TAPE output connections Connecting an External Aerial If the Quattro is equipped with an internal FM tuner module it will be necessary to connect an aerial to the unit The aerial is connected to the rear panel FM aerial socket and the quality of the aerial will directly affect the performance of your Quattro Indoor aerials are not generally suitable for FM receivers and may result in a limited selection of stations and a high level of background noise We would therefore advise that you contact an aerial installation expert in yo
12. mander supplied with Cyrus amplifiers will control all system functions for the Quattro and other components Note The remote control supplied with the Quattro will no longer operate the unit CD Dir TAPE OUT MC BUS 0000 ad Quattro mo Qdoooooa DJ MC BUS 0600000000 Yoo Cyrus 7 690 6606000608 GOO EST TU in CD in Downloaded From Disc Player com Cyrus Manuals User Instructions TROUBLESHOOTING GUIDE If your Cyrus Quattro is not operating properly disconnect the power and check all connections using the notes in this handbook If problems persist the checklist below may help If you are in any doubt consult your dealer Switch off the power to the audio system and check that connections have been correctly made from the Cyrus Quattro to the power amplifier Disc Spinning with no sound from the speakers Switch on amplifier Disconnect headphones Press the PLAY PAUSE key again on the front panel or handset to cancel pause Skipping tracks or distorted sound The disc may be dirty or badly Try playing another disc If the other scratched disc plays ok try cleaning the 1st disc Indication Disc error on the display The disc will not read It may be dirty or defective Unable to select FM radio Power amplifier not switched on Headphones connected to the rear panel socket Pause may have been set Chec
13. n 0 0025 Audio Performance optional FM radio module Sensitivity Mono 30dB S N cssceeseeseeseeeseesneseeseeeseeteessneeeeeesnees Sensitivity Stereo 50dB S N Pilot Tone Suppression Stereo Separation sentent S N Ratio mono SIN Ratio stereo 0 0 0 THD mono 1kHz 50kHz Dev THD stereo 1kHz 50kHz Dev 0 35 Cyrus reserves the right to change all specifications without notice E amp OE Downloaded From Disc Player com Cyrus Manuals
14. nded by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer ATTACHMENTS Do not use attachments not recommended by the product manufacturer as they may cause hazards MOVING THE PRODUCT A product and cart combination should be moved with care Sudden stops excessive force and uneven surfaces may cause the product and cart to overturn POWER SOURCES This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions OVERLOADING Never overload wall outlets extension cords or integral convenience receptacles This can result in an increased risk of fire or electric shock GB Downloaded From Disc Player com Cyrus Manuals Cyrus Quattro POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product NAKED FLAMES No naked flame sources such as candles must be placed on this product LIGHTNING For added protection for this product
15. preset number and the station will be stored for later recall 4 Repeat the sequence to store your other favourite radio stations Cyrus Quattro Connection and Operation of the Quattro as a CD Tuner Source The Quattro may be supplied or converted to provide the functions of a high quality CD and Tuner source when optional tuner module is fitted in a Cyrus system When this conversion has been made the legend Pre amp will no longer appear as an installed option on the display when the Quattro is connected to the AC power Connecting the CD output to the amplifier Connect the CD Direct Outputs from the Quattro to the CD input of the amplifier Connecting the tuner output to the amplifier If a tuner module is fitted the output signal will be routed through the Tape Output of the Quattro Connect the Tape Outputs from the Quattro to the Tuner input of the amplifier MC Bus connection The Quattro may be connected into an MC Bus loop with other Cyrus products to enable remote system power control from the main amplifier Refer to the amplifier instructions for an MC Bus wiring diagram Front panel operation The front panel keys for controlling CD and tuner functions will still operate but there will be no response from the keys for Input Source Selection or Volume Control these functions will be available from the system amplifier Remote Control Operation A Cyrus System remote control such as the Audio Com
16. rosol cleaners Use a damp cloth for cleaning WATER AND MOISTURE Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like The product must not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the product HEAT The product should be situated away from heat sources such as radiators stoves or any other products including amplifiers that produce heat VENTILATION Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to OBJECT OR LIQUID ENTRY Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock ACCESSORIES Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recomme
17. ug fuse should be 3A SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel CONDITIONS REQUIRING SERVICE Unplug this product from the wall outlet and refer servicing to qualified service personnel when When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the product If the product has been exposed to rain or water If the product has been dropped or damaged in any way If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions Improper adjustment of other controls may result in damage requiring extensive work by a qualified technician to restore the product to its normal operation When the product exhibits a distinct change in performance REPLACEMENT PARTS When replacement parts are required be sure the service technician has used replacements specified by the manufacturer or have the same characteristics as the original part Unauthorised substitutions may result in fire electric shock or other hazards SAFETY CHECK Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition PRODUCT SERVICE CENTRES For
18. ur local area or consult your dealer concerning the installation of an external aerial In areas where FM cable transmission is available the reception should be adequate Connecting to the CD Digital Output ACD Digital Output is available from the Quattro which can be connected to any compatible product with a suitable Digital Input The CD Digital Output is particularly suitable for making direct digital recording to Digital Tape or Disc recorders Connect the CD Digital Output of the Quattro to the Digital Input of the other unit with a suitable phono cable intended for digital signals Multi room Connections The Multi room connections for Zone 1 Zone 2 and Zone 3 and for the Multi room comms unit should not be connected unless the Multi room upgrade has been fitted internally by your dealer When this upgrade is fitted the front panel display will read Multi room as an installed option when first connected to mains power A separate handbook is included with the Multi room module which includes wiring and operational instructions for this unit Caution Damage may result from the connection of any other equipment to these sockets MC Bus System Connection Optional MC Bus is an optional connection for remote power control of the system power amplifier If the power amplifier has MC Bus connections first connect the MC Bus Output of the Quattro to the MC Bus Input of the power amplifier Then connect the
Download Pdf Manuals
Related Search