M14T 1.0.indd
Contents
1. 3 Install four M 3 screws into these holes 2 Align and Secure y the HDD onto the 2 drive tray with 4 M 3 screws r M 3 Screw 11 SUPER CSE M14T Mobile Rack User s Guide 3 5 3 Installing Hard Disk Drives into the Mobile Rack Procedures 1 After you ve installed a hard disk drive into a drive tray as indicated in Section 3 5 2 you are ready to install the HDD into the mobile rack 2 Insert a hard drive into a drive bay located in the mobile rack as shown below 1 Insert a hard drive into the drive bay 3 Push the HDD inward until it is fully seated into the drive bay 4 Press the handle toward the locking position When the handle is in the correct position the handle will automatically lock 4 When the handle is in the correct position the release tab will automatically lock 12 Rear Window Removal 3 6 Rear Window Removal Optional Procedures 1 Follow the procedures listed on Section 3 4 to remove the cooling fan from the CSE M14T 2 After the cooling fan is detached remove the four screws from the CSE M14T as shown below 2 Remove the screws 3 Pull the rear window away from the mobile rack to remove it 3 Once the screws are removed pull the rear window away from the CSE M14T to remove it Procedures Rear Window Installation Reverse the steps listed above to install the Rear Window onto the CSE M14T 13 SUPER CSE M14T2. CSE M14T Mobile Rack USER S GUIDE Rev 1 0 SUPER CSE M14T Mobile Rack User s Guide The information in this User s Guide has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com SUPERMICRO COMPUTER reserves the right to make changes to the product described in this manual at any time and without notice This product including software if any and documenta tion may not in whole or in part be copied photocopied reproduced translated or reduced to any medium or machine without prior written consent IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of
3. California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Supermicro s total liability for all claims will not exceed the price paid for the hardware product Manual Revision Rev 1 0 Release Date April 7 2006 Unless you request and receive written permission from SUPER MICRO COMPUTER Inc you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2006 by SUPER MICRO COMPUTER INC All rights reserved Printed in the United States of America Table of Contents Chapter I 1 1 1 2 1 3 Chapter 2 2 1 2 A 2 B Chapter 3 3 1 3 2 3 3 3 4 3 5 3 5 1 3 5 2 3 5 3 3 6 Table of Contents IMtOCUCTI ON iyar ce ul dken dan Ki rae vedan detent deh a Gude YEL K Kuda cd SE SE kw EV KEV ER 4 Overview ea Product Features a nad MEL Sekina aKa o G eyar e a ab Parek E save kin 4 Contacting Supermicro l ii iiEkkkkkkkk kk kkk kek EKA KAK AKAN AA AKA WAA 5 Technical Specifications c seers eee keke 6 SASM14V Backplane ccccccccceccceeeseeeeeeeseeeeeeeseeaeeeeseeeeeeeasseeeeeeseneeeeeeas 6 SASM14V Front Panel sack kincin Aas one eid Ane Ales 6 SASM14V Back Panel niaren otani aei eea AE 7 Installat
4. Mobile Rack User s Guide Notes 14
5. Removal Note If your CSE M14T Mobile Rack is a stand alone model you will need to install the cooling fan onto the CSE M14T before using it Procedures Fan Installation 1 Attach the cooling fan to the CSE M14T Mobile Rack and secure it to the Mobile Rack with two screws on both sides of the fan 2 Connect the cooling fan cable to the Fan Connector as shown below 1b Install two screws to secure it to the e mobile rack 2 Fan Connector Procedures Cooling Fan Removal Reverse the steps listed above to remove the cooling fan from the CSE M14T SUPER CSE M14T Mobile Rack User s Guide 3 5 HDD Installation 3 5 1 Removing the HDD Drive Tray Before installing the hard disk into the CSE M14T you will need to remove the HDD drive trays from the cage Procedures 1 Press the release tab toward the right to release the HDD drive tray from the CSE M14T cage 2 Once the drive tray is unlocked pull it out from the CSE M14T 1 Press the release tab toward the right to release it 3 Follow the procedures above to remove other HDD drive trays 10 HDD Installation 3 5 2 Installing the Hard Disk Drive into the Drive Tray Procedures 1 Place a 2 5 Hard Drive Disk on top of the drive tray 2 Align the HDD against the drive tray 3 Secure the HDD onto the drive tray by installing four M 3 Screws into the holes as shown below 1 Place the HDD a1 top of the drive tray
6. bile Rack Slim design small size form factor SFF 5 8 W x 1 7 H x 7 9 D e Supports 4 x 2 5 hot swap SFF HDD e Supports up to 5V 10A Average and 12V 10A Average Running up to 3 Gbps Supports SAS SATA Operating Systems supported Windows 2000 Windows XP and Windows 2003 Linux Red Hat and SuSE Upgradable in the future System Monitoring Overheat Fan Fail LED indicators and audible alarm indicating system overheat or fan failure Drive Activity LED to indicate the activity status of each disk drive An Important Note to the User The pictures or graphics shown in this User s Guide were based upon the latest PCB revision available at the time of the publishing of this manual The CSE M14T Mobile Rack you ve received may or may not look exactly the same as the graphics shown in this manual Contacting Supermicro 1 3 Contacting Supermicro Headquarters Address Tel Fax Email Web Site Europe Address Tel Fax Email Asia Pacific Address Tel Fax Web Site SuperMicro Computer Inc 980 Rock Ave San Jose CA 95131 U S A 1 408 503 8000 1 408 503 8008 marketing supermicro com General Information support supermicro com Technical Support www supermicro com SuperMicro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands 31 0 73 6400390 31 0 73 6416525 sales supermicro nl General Information support supermicro
7. ion Instructions sassssssssnunnssnnnnnnnnnnnnnnnnnnnnnnennnnnnnnna 8 Packing listeron aea a e ana Sa bran Va Vek eE Kak ey Ae eV ek d Ve S Tools needed Jsi Important Safety Guidelines ccccesecceeseseeeeeeeeeeeeeeeeeeeeeeeseeeeeeeseeees 8 Cooling Fan Installation and Removal ccssseeeeeeeseeeeeeeeeeeeeeeeeee 9 HDD Installation Removing the HDD Drive Tray ui kk kk kk k Installing the Hard Drive Disk into the Drive Tray Installing the Hard Drive Disk into the Drive Tray Rear Window Removal Optional ccccsseecceeeeseceeeeseeeeeeeeeeeeeeeeas SUPER CSE M14T Mobile Rack User s Guide Chapter 1 Introduction 1 1 Overview This manual is written for system integrators PC technicians and knowledgeable PC users who intend to integrate Supermicro s intelligent highly expandable and cost effective mobile rack solutions into their systems It provides the user with detailed information for the installation and use of the CSE M14T Mobile Rack The Supermicro CSE M14T Mobile Rack supporting up to four hot swap SAS SATA hard drives packaged in the small size form factor 5 8 W x 1 7 H x 7 9 D and running up to 3 Gbps showcases today s most advanced technology innovations in modular connectivity and data transferability laying the foundation for reliable effective and scalable solutions for tomorrow s data communications industry 1 2 Product Features The CSE M14T Mo
8. nl Technical Support rma supermicro nl Customer Support SuperMicro Taiwan 4F No 232 1 Liancheng Road Chung Ho 235 Taipei Hsien Taiwan R O C 886 2 8226 3990 886 2 8226 3991 www supermicro com tw Technical Support Email support supermicro com tw SUPER CSE M14T Mobile Rack User s Guide Chapter 2 SASM14V Backplane 2 A SASM14V Front Panel Front View J1 J3 SAS SATA 0 SAS SATA 2 SUPER SASM14V SAS SATA 1 SAS SATA 3 EID13 LED 2 A 1 Front Connectors Front Connectors J1 SAS SATA O J2 SAS SATA 1 J3 SAS SATA 2 J4 SAS SATA 3 2 A 2 Front LED Indicators Front LED Indicators D3 Overheat LED D4 Fan Failure LED D12 SAS SATA 0 ACT LED D13 SAS SATA 1 ACT LED D14 SAS SATA 2 ACT LED D15 SAS SATA 3 ACT LED Technical Specifications 2 B SASM14V Rear Panel JP22 Rear View JP26 eaters YS ACT In Fan lt a C O ee TT LU En 3 WE N HILL i ji V GND GND HN H e u 4 Pin PWR R sfl JP18 e Hun BBE nn TIT 0 alP25 2 B 1 Rear Side Connectors JP10 4 pin power connector pin Power Connector Pin Definitions There is a 4 Pin Power Connector Te Pin Definition JP10 located on the rear side of the SEN SASM14V Backplane This power con 2 Ground necto
9. r damaged please contact your retailer immediately One 4 drive Mobile Rack Cage CSE M14 B P Four hot swap 2 5 HDD trays One cooling fan assembly 40MM One screw set for 4 HDDs One SAS SATA Backplane CSE SAS M14EV One SATA Big4 to individual port fan out cable CBL 0103 3 2 Tools Needed The following tools are needed for the installation of the mobile rack into chassis 1 Phillips Screw Driver 2 Antistatic Strap recommended 3 3 Important Safety Guidelines This product shall only be accessed assembled and serviced by techni cally qualified personnel or technicians To avoid personal injury and property damage please carefully follow all the Safety Guidelines listed below before accessing or servicing the CSE M14T Safety Steps Before accessing the Mobile Rack 1 Turn off all peripheral devices and the power supply connected to the chassis and unplug all power cords from the system or the wall outlets 2 Disconnect all the cables and label the cables for easy identification 3 Use a grounded wrist strap designed to prevent static discharge when handling components 5 Save all the screws and fasteners for later use If necessary label these screws or fasteners for easy identification 6 Follow the instructions given in the following section to remove and install the cooling fan hard disks and the rear window Cooling Fan Installation and Removal 3 4 Cooling Fan Installation and
10. r must be connected to your power ji 3 Ground supply to provide adequate power to the n a HE backplane See the table on the right for la j gt _ pin definitions JP11 SAS In connector JP22 3 pin Fan Header Fan Header There is a 3 pin fan header JP22 lo Pin Definitions JP22 cated on the rear side of the SASM14V Pin Definition Backplane Connect a cable to the fan 1 Ground header to provide cooling to the back 2 12V plane See the table on the right for pin 2 Tachometer definitions JP26 ACT In Header Act ln Header A 4 pin Act In header JP26 located on Pin Definitions JP26 the rear side of the SASM14V Backplane Pin Definition indicates the activity status of SAS SATA Open Act In 0 3 Default slots that are installed on the front side of 1 Act In 0 the backplane See the table on the right 2 Act In 1 for pin definitions 3 Act In 2 2 B 2 Rear Side Jumpers 4 Act n a Jumper Description Definition JP18 Open Default Normal Closed Buzzer Reset JP25 Open Set Overheat Temperature to 45 C Pins 1 2 Default Set Overheat Temperature to 50 C Pins 2 3 Set Overheat Temperature to 55 C JP42 Open Fan Disabled Closed Default Fan Enabled 7 SUPER CSE M14T Mobile Rack User s Guide Chapter 3 Installation Instructions 3 1 Packing List Examine the following items that are included in your shipping package If any items are missing o
Download Pdf Manuals
Related Search