Quickie® P-220 P-222SE Integrated CG Tilt User
Contents
1. A B QTRONIX Power Module 930478 Rev A 12 VI Operating Guide TO OPERATE THE C G TILT A TOGGLE SWITCH ACTIVATION A 1 To operate push the toggle switch A forward to tilt back or pull toggle backward to return to neutral until tilted into the desired posi L tion 2 The toggle switch will return to neutral when released and the seating system will stop moving B SINGLE SWITCH ACTIVATION 1 Depress and hold single switch to tilt back into the desired position 2 Depress and hold single switch to return to neutral until tilted into the desired position C INTEGRAL JOYSTICK ACTIVATION OPTIONAL From the off position 1 Push the on off button A once to turn the chair on 2 Push either tilt button B or C to activate tilt mode 3 Push forward on joystick D to tilt back 4 Pull backward on joystick D to tilt forward 5 Push either tilt button B or C to deactivate and resume drive mode D REMOTE JOYSTICK ACTIVATION OPTIONAL From the off position 1 Push the on off mode select toggle switch A down once to turn the chair on 2 Push the on off mode select toggle switch A up twice to move index to tilt mode noted by two 2 actuator lights B 3 Push the joystick C forward to tilt backward or backward to tilt forward 4 Push the on off mode select toggle switch A up once to2. 13 A Maintenance ove y ved va ee eee eee EXE EN a evene ERN RE VERE 13 B Troubleshooting Tips fete eeu io den e eoe rever ee egre recita sel open 13 VIII WIRING DIAGRAMS ederet ero eere trop teen etae anne no aoa 14 IX SUNRISE LIMITED nnne 16 930478 Rev A optional P 220 Headrest 4 III Your Chair amp Its Parts 1 ISS 8 Quickie P 220 P 222SE Integrated C G Tilt 1 Push Handle 4 Swing Away Footrest Hanger 2 Dual Post Height Adjustable 5 Footrest Release Lever Armrest optional 6 Angle Adjustable Footplate 3 Remote Joystick 7 Backrest 8 9 standard P 222 SE Seat Pan with optional cushion 930478 Rev A III Chair Your amp Its Parts 5 Joystick P 220 Standard integral right hand or left hand mount Option remote left hand or right hand mount Option swing away retractable joystick Joystick P 222SE Standard remote left hand or right hand mount Option swing away retractable joystick Batteries 2 batteries required to operate chair Option GP 24 deep cycle gel Option 22 NF deep cycle gel Battery Charger Standard off board Lester Seat Frame Dimensions Seat Frame width standard 14 20 Seat depth 14 20 adjustable Solid seat back Aluminum seat pan Optional cushions Jay Cushions CG Tilt 0 50 3
3. eto DOES diea dese deus 6 D Changes amp 6 V SET UP ADJUSTMENT amp nenne 7 A Battery Removals cues on Lene decrease duro eee RUE sans 7 B Solid Seat Back amp Lateral Thoracic Supports 8 EE 8 D Foam Back 9 E Seat Tilt Adjustments amp Drive Lock out eeeeeeeeeeeeennne 9 E Seat Depth ettet de tene cara se 9 Gs Backfest seo i ree oe eere aere veo eae eter 10 Seat Height Adjustment ceeeeeeeeeeeseeeeeeeeeeee nennen nenne 10 I TM40 Single or Dual Switch Actuator 10 Ji CHECK OUb E 11 VI OPERATING GUIDE noa reg ieu dada epus 12 A Toggle Switch Activation esee 12 B Single Switch Activation sssini terrre errorae yh areas resa EY e 12 C Integral Joystick Activation 12 D Remote Joystick Activation ssssssssssessseeeeeeeeeeeceeeeeeeeeeeeeeeeeeeeeeeeees 12 E Specialty Drive 5 12 VII MAINTENANCE amp TROUBLESHOOTING TIPS
4. 53 Backrest Standard Non folding 15 20 Straight Backpost standard Footrest Standard Swing away with angle adjustable footplates and heel loops Option elevating legrests and multiposition Armrests Standard dual post flip back Option height adjustable dual post or single post with desk or full length waterfall pads or stan dard armpads Swing Away Lateral Thoracic Supports Option Curved Option Straight Headrest Standard 8 x 5 or 7 x 4 5 headrest pad All features may not be available with some chair setups or in conjunction with another chair feature Please consult your supplier for more information Your authorized supplier can also provide you with more information on accessories 930478 Rev A 6 IV Warnings V Set up Adjustment amp Use A SOLID SEAT BACK AWARNING Do not use the Solid Seat Back to push or lift the wheelchair Improper use may cause the back to unexpectedly detach from the wheelchair B DRIVING AWARNING You should drive your chair with the tilt at the minimum angle C TILTING AWARNING To prevent damage and personal injury avoid tilting near objects such as walls tables or chairs To avoid injury ensure other people especially children are clear of the system If using a swing away abductor be sure not to tilt with the abductor swung away Otherwise the abductor may collide with the tilt actuator when returning to the untilted position
5. D CHANGES amp ADJUSTMENTS AWARNING Never use non Quickie parts or make changes to your chair unless authorized by Sunrise Doing so will void the warranty and may create a safety hazard 1 If you modify or adjust this chair it may increase the risk of fall or tip over 2 Modifications unauthorized by Sunrise constitutes remanufacturing of the wheelchair This voids the warranty The rider then assumes all future liability for the wheelchair 930478 Rev A TOOLS YOU WILL NEED 1 Basic Tool Kit To set up adjust and maintain your chair you will need the following tools e 5 32 Allen wrench e 3 16 Allen wrench e 5 16 Allen wrench e 9 16 box and open end wrench e 1 2 box and open end wrench e Phillips screwdriver 1 e Standard slot screwdriver NOTE Setting the wheelchair on a flat surface such as a table or a workbench helps make these procedures easier A BATTERY REMOVAL To remove the batteries for transporting or servicing Remove Batteries a Remove seat and main frame from power drive unit using quick release levers C b Lift battery compartment lid E off of power drive unit c Prevent the power drive unit from tipping for ward by placing a solid object underneath the front of the power drive unit d Disconnect battery leads from power harness e Lift rear most battery out using the battery straps F f Pull the front battery rearward disconnect it and remove it using the battery straps
6. due to the vertical movement of this adjustment collar clamp D will have to be moved in conjunction 3 Retighten both the 3 16 Allen and the set screws A with a 3 32 Allen wrench pivot plate b Reposition the backrest to the desired position Note Substitute Bolt D with rear back rest pivot plate bolt C for 18 seat depth c Replace and retighten bolts on each side of the backrest pivot plate 930478 Rev A 930478 Rev A 10 V Set up Adjustment amp Use V Set up Adjustment amp Use 11 G BACKREST A backrest angle adjustment is standard 1 Adjustment on Seat Frame a Remove the front securing bolt C on the side of the backrest hinge plate b Loosen the lower rear bolt D c Set at desired angle There are four holes in 4 increments to choose from d Reinstall the front bolt and tighten both bolts securely H SEAT HEIGHT ADJUSTMENT The front seat height can be adjusted from 19 75 to 21 75 in 1 increments Adjust front seat frame posts X up or down to desired height The rear seat height can be adjusted to change the seat angle relative to the front seat height The com ponents to change rear seat height are include with each P 220 P 222 SE Installing 2 each of part number 540176 will elevate the rear 1 from standard Installing 2 each of part number 540177 will elevate the rear 2 It is recommended that a qualified dealer provide this service if desired I T
7. 1 YEAR We warrant other electronic components such as the single switch actuator controller for one 1 year from the date of first consumer purchase ADDITIONAL WARRANTY We warrant all other original components such as upholstery plastic rubber parts and painted surfaces for three 3 months from the date of first consumer purchase 930478 Rev A SUNRISE MEDICAL Sunrise Medical 7477 East Dry Creek Parkway Longmont Colorado 80503 USA 800 333 4000 In Canada 800 263 3390 9 2002 Sunrise Medical 5 02 930478 Rev A
8. A WARNING Batteries may weigh up to 55 lbs 25 kg Care must be taken to avoid injury when lifting ES 930478 Rev A 8 V Set up Adjustment amp Use V Set up Adjustment amp Use 9 B SOLID SEAT BACK amp LATERAL THORACIC SUPPORTS D FOAM BACK 1 To adjust the height of the lateral support Secure the foam and cover to the shell mount loosen the adjustment screw until the To secure the back foam and cover on the Solid Seat Back slide the top edge receiver slides freely on the back posts Tighten of the cover over the top lip of the shell Press the back in place against the the adjustment screw when the proper height is shell determined E SEAT TILT ADJUSTMENTS amp DRIVE LOCK OUT 2 Assess and fit the lateral thoracic supports Assess client for proper positioning of the later al thoracic supports Each support is indepen dent and may be adjusted for your client s clini 1 Maximum Tilt Angle Maximum tilt angle can be adjusted to a limit of 50 a Remove access cover on the actuator housing b Position the most forward switch such that the actuator shuts down when cal need the desired maximum tilt is achieved A WARNING c Tighten the switch to the track and replace the cover on the actuator A minimum of 1 2 5 cm of clearance should housing exist between the top of the lateral support 2 Drive Lock out Angle and the user s arm pit The drive lock out angle is adjust
9. M40 SINGLE OR DUAL SWITCH ACTUATOR CONTROLLER Refer to diagram on next page The TM40 actuator controller can be used to activate the tilt mechanism with either single or dual switch controls 1 Plug limit switch harness assembly A into TM4O limit switch jack B 2 Plug single switch into TM40 single switch jack D OR plug dual switch E into TM40 dual switch jack F 3 Plug TM40 into the QTRONIX Power Module G 4 Use mating plugs H to connect the TM40 to the tilt actuator 930478 Rev A J CHECK OUT Once the tilt assembly is adjusted it should actuate smoothly and easily All accessories should also perform smoothly Verify seat can achieve full tilt and will return to neutral Verify the motor cuts out once the neutral position is reached Verify no debris is interfering with the glide bearings Verify all hardware is securely tightened Verify that the drive lock out switch is positioned to prevent driving if the system is tilted to an angle of greater than 15 AWARNING If the actuator stop switches are not properly adjusted the actuator will cur rent limit or stall at the end of the stroke Repeated stall conditions will shorten the life of the actuator Hn __ amp d TM 40 Stereo Jack F
10. Quickies P 220 P 222SE Integrated C G Tilt SUPPLIER RIDER THIS MANUAL MUST BE BEFORE USING THIS GIVEN TO THE RIDER OF WHEELCHAIR READ THIS THIS WHEELCHAIR ENTIRE MANUAL AND SAVE FOR FUTURE REFERENCE SUNRISE MEDICAL User Instruction Manual amp Warranty I Introduction Note QUICKIE P 220 P 222SE INTEGRATED C G TILT USER INSTRUCTION MANUAL SUPPLEMENT NOTE This supplement contains information on the operation and adjustments for the Integrated C G Tilt System of a Quickie P 220 P 222SE wheelchair ONLY Please refer to the Quickie P 220 P 222SE User Instruction Manual for additional notices EMI infor mation warnings tips for attendants set up adjustment and use information operat ing guide battery and maintenance information wiring diagrams and warranty infor mation regarding the Quickie P 220 P 222SE 930478 Rev A Sunrise Medical Customer Service Department 7477 East Dry Creek Parkway Longmont Colorado 80503 303 218 4500 or 800 333 4000 II Table of Contents 3 I INTRODUCTION NOTE conire e scectvcsdisceceissscnceotscescvescctcseceevesesvosotenstiases 2 II TABLE OF 3 III YOUR CHAIR AND ITS PARTS 4 IAM n 6 A Solid Seat Back erri eere Dr ertet reete een nenne eaae cha PE dna 6 E M 6 Cop TINO de deveras san Data rece ee
11. able a To adjust the height angle or width of the a Tilt the seat back at least 15 20 lateral thoracic support pads loosen the top b Remove the access cover on the actuator bolts and slide to correct width Tighten bolt c Adjust the middle limit switch until the desired lock out position is to bolt plate If more adjustment is neces achieved sary loosen the internally mounted bolts d Replace the access cover on the actuator housing and slide in the track to the desired height NOTE The drive lock out should be set such that the chair cannot be driven with the and width The angle is obtained by tilting seat tilted to an angle of greater than 15 the bracket as needed Tighten the bolts b To adjust the depth of the lateral thoracic SEAT DEPTH pads turn the middle bracket so that the The seat depth can be adjusted in one inch increments slots are on side Adjust to desired depth Re 1 Seat Frame Depth Adjustment tighten the bolts a To adjust remove the two bolts C amp D p 10 from each side of the backrest C HEADREST 1 Mounting a headrest The Solid Seat Back has a headrest plate mounted to it Care should be taken to use the proper screw length when mounting 2 To position the headrest use the double clamp and the collar clamp B C D to obtain the proper height and distance For clamp B use a 3 32 Allen set screw A and a 3 16 Allen cap screw Clamp B positions the headrest forward and aft However
12. g use a foreign matter may have come into contact with the glide bearings If this occurs use a clean dry cloth or compressed air to clear or if needed please see your authorized Sunrise supplier If your tilt system will not function check to ensure the tilt lock out sensor is seated properly in its mount The wires should lead out of the sensor toward the front of the chair 930478 Rev A VIII Wiring Diagrams 14 TM40 ACTUATOR CONTROLLER Independent switch control and Integral Joystick 7 VIII Wiring Diagrams 15 930478 Rev ALM ACTUATOR CONTROLLER Through drive control Integral Joystick 930478 Rev A 16 Ix Sunrise Limited Warranty FOR THREE 3 YEARS We warrant the C G power tilt seating system seat frame sub base frame actuator and structural components of this wheelchair against defects in materials and workmanship for three 3 years from the date of first consumer purchase FOR TWO 2 YEARS We warrant the ALM Actuator Lights Module actuator controller for two 2 years from the date of first consumer purchase FOR ONE
13. return to drive mode E SPECIALTY DRIVE CONTROLS OPTIONAL Please refer to your QTRONIX USCM User Instruction Manual CAUTION The power base drive lock out feature will activate and the chair cannot be driven if the seating system is tilted more than 20 930478 Rev A VII Maintenance amp Troubleshooting Tips 13 A MAINTENANCE You should check the items on this chart at the indicated intervals If any of the items are loose worn bent or distorted immediately have them checked and or repaired by your authorized Sunrise supplier Frequent maintenance and servicing will improve per formance and extend wheelchair life NOTE Check weekly and use a clean dry cloth or compressed air as needed to keep glide bearings free of debris CHECK Charge Batteries Glide bearings free of debris Check tires for proper inflation level Check batteries for proper electrolyte level wet cell only Check plugs and connectors for proper connections Check all moving parts for wear Inspect all nuts bolts and fasteners for looseness or wear Inspect upholstery for wear Remove and inspect motor brushes Servicing by authorized Supplier Check front mount bolts for looseness Check actuator limit switch position Check front mount for excessive wear B TROUBLESHOOTING TIPS If you should notice your C G Tilt system binding up not running in a smooth fash ion or emitting an unusual noise durin
Download Pdf Manuals
Related Search