VCD 4612 Quick Reference
Contents
1. communication between terminal and cradle Rechargeable battery in terminal or spare battery did not charge Probable Cause Cradle driver not loaded Action Ensure that the cradle driver is loaded Cradle mode not enabled Enable cradle mode via the appropriate API Terminal improperly installed in cradle Battery failed Remove terminal from cradle and re insert Replace battery Terminal or battery was removed from cradle too soon OR Battery or terminal improperly installed in cradle Replace terminal and or spare battery in cradle and begin charging over Bat tery requires 2 hours to recharge fully Quick Reference Regulatory Information Radio Frequency Interference Requirements United States This device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the Federal Communications Commissions Rules and Regulation These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generate uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment ina residential area is likely to cause harmful interference in which case the user will be required to correct the interfer2. for mounting connecting operating and troubleshooting the VCD 4612 vehicle mount cradle Information on the standard cradle can be found in the CRD4600 Cradle Quick Reference Guide p n 70 15861 XX Quick Reference Parts of the Cradle Lock Upper Step Half VGA Lower Step Full Screen Mounting Bracket J Attachment Clips for Half VGA Display Only Lower Holding Brackets Power LED Spare Battery Charging LED Spare Battery Charging Slot Quick Reference Installing the Vehicle Cradle The vehicle cradle can be mounted on the floor or dash of a truck Each cradle includes a vehicle power supply capable of power conditioning in an operating range of 10 48 volts To install the vehicle cradle 1 Release the cradle from the metal bracket by removing the four 8 phillips head screws in the cradle as shown below Install the mounting bracket on the dash or other appropriate mounting surface a Position the bracket on the mounting surface b Fasten using the appropriate hardware Oo ofJUZJo FU Remove Bracket for Positioning on Mounting Surface Position the cradle against the mounting bracket Fasten using the four 8 phillips head screws removed in Step 1 Insert the power connector in the power port on the bottom of the cradle Quick Reference 6 If the power connector is e
3. 3 610 5 545 889 5 552 592 5 578 810 5 581 070 5 589 679 5 589 680 5 608 202 5 612 531 5 619 028 5 664 229 5 668 803 5 675 139 5 693 929 5 698 835 5 714 746 5 723 851 5 734 152 5 734 153 D305 885 D341 584 D344 501 D359 483 D362 435 D363 700 D363 918 D370 478 D383 124 D391 250 Invention No 55 358 62 539 69 060 69 187 Taiwan No 1 601 796 1 907 875 1 955 269 Japan European Patent 367 299 414 281 367 300 367 298 UK 2 072 832 France 81 03938 Italy 1 138 713 rev 4 98 70 17024 03 Revision A June 1998
4. VCD 4612 Quick Reference 1995 1998 SYMBOL TECHNOLOGIES INC All rights reserved Symbol reserves the right to make changes to any product to improve reliability function or design Symbol does not assume any product liability arising out of or in connection with the application or use of any product circuit or application described herein No license is granted either expressly or by implication estoppel or otherwise under any patent right or patent covering or relating to any combination system apparatus machine material method or process in which Symbol products might be used An implied license only exists for equipment circuits and subsystems contained in Symbol products Symbol is a registered trademark of Symbol Technologies Inc Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged Symbol Technologies Inc One Symbol Plaza Holtsville New York 11742 1300 http www symbol com Quick Reference Introduction Cradles are optional devices which can be used for charging the terminal s battery and for communicating with the host or with other cradle chains The PPT 4600 offers several cradle configurations a standard cradle that can be tabletop or wall mounted and a cradle for vehicle use About This Guide This guide provides the operator and system administrator with instructions
5. ation technology Equipment EN 50 082 1 Electromagnetic Compatibility Generic Immunity Standard Part 1 Res idential commercial Light Industry IEC 801 2 Electromagnetic Compatibility for Industrial Process Measurement and Control Equipment Part 2 Electrostatic Discharge Requirements IEC 801 3 Electromagnetic Compatibility for Industrial Process Measurement and Control Equipment Part 3 Radiated Electromagnetic Field Requirements IEC 801 4 Electromagnetic Compatibility for Industrial Process Measurement and Control Equipment Part 4 Electrical Fast Transients Requirements EN 60 950 Amd 1 Amd 2 Safety of Information Technology Equipment Including Electrical Business Equipment EN 60 825 1 EN 60 825 Safety of Devices Containing Lasers Quick Reference Warranty Information In the U S A for service information warranty information or technical assistance call the Symbol Support Center 1 800 653 5350 If you purchased your Symbol product from a Symbol Business Partner contact that Business Partner for service Outside North America contact your local Symbol representative Warranty Symbol products are warranted against defects in workmanship and materials for a period of one year from the date of shipment provided that the product remains unmodified and is operated under normal and proper conditions This warranty is limited to repair or replacement at Symbol s option with reasonable promptnes
6. ence at his own expense However there is no guarantee that interference will not occur in a particular installation If the equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Radio Frequency Interference Requirements Canada This Class A digital apparatus meets the requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la Classe A respecte toutes les exigences du Reglement sur le Materi l Brouilleur du Canada CE Marking and European Union Compliance Products intended for sale within the European Union are marked with the CE Mark which indicates compliance to applicable Directives and European Normes EN as follows Amendments to these Directives or ENs are included Applicable Directives e Electromagnetic Compatibility Directive 89 336 EEC e Low Voltage Directive 73 23 EEC Quick Reference Applicable Standards EN 55 022 Limits and Methods of Measurement of Radio Interference Characteristics of Inform
7. not secure and may not make solid contact with the power and communications connectors 1 Slide Base Behind Bracket PPT 4600 Secured in the VCD 4612 Quick Reference 2 The terminal powers on automatically The terminal s Communications LED turns solid green if the terminal is enabled and flashes if the terminal also has control of the bus The Communications LED does not light if the cradle is not enabled To lock the terminal in the cradle push down the lock at the top of the cradle A key is provided with the cradle 1 ee Lock in Place YZ FA Tl Key Lock Quick Reference Removing the PPT 4600 from the VCD 4612 If necessary unlock the cradle using the key provided Grip the 4600 by a side panel With your thumb press up on the wing s notch to release the terminal Press on Wing Lift Terminal Out of Cradle 4 Pull the terminal straight up and out of the cradle Caution Removing the terminal from the cradle when the COMMU NICATIONS LED is blinking may disrupt communications between the terminal and communicating device Quick Reference Recharging the Battery in the Terminal The cradle automatically recharges the battery when the terminal is properly inserted in the cradle Note Charge the battery fully before using the terminal Note Ensure that the terminal placed in the cradle has a battery installed Note T
8. o charge the spare battery pack it must be inserted in the cradle before the terminal is inserted refer to the Recharging the Spare Battery Pack section To charge a battery pack in the terminal 1 Verify that the cradle has power Connect the cradle s power supply jack as described in Installing the Vehicle Cradle Insert the terminal in the cradle and verify that it is properly seated The terminal automatically powers on if the necessary software driver is loaded in the terminal and the Battery Charging LED turns amber The terminal s Battery Charging LED shows amber while charging When the battery pack is close to being charged the LED toggles between amber and green and switches to solid green once the pack is fully charged Leave the terminal in the cradle for a minimum of 1 hour The cradle requires up to 2 hours to recharge a fully discharged battery To prevent overcharging the cradle power shuts off once the battery is fully charged Quick Reference Recharging the Spare Battery Pack To charge a spare battery pack it must be inserted in the cradle before a terminal is placed in the cradle To recharge a spare battery pack 1 Verify that the cradle has power Connect the cradle s power supply jack as described in In stalling the Vehicle Cradle Insert the battery pack in the charging slot until it is firmly D seated 3 The battery begins cha
9. quipped with a cigarette adapter 10 48V plug the adapter into the cigarette lighter receptacle If the power connector is equipped with a standard 10 48V wire connect connect the cable directly to a fuse panel Note This must be done by a qualified installer Quick Reference Other Connectors Cradle Configurations The ports illustrated below are located on the bottom of the E With Power Port With Power Port and RJ 41 Port Connection to SMG To connect a vehicle cradle to the Symbol Mobile Gateway SMG 1 Insert the RJ 41 connector in the RJ 41 port on the base of the cradle Insert the other connector in the communications port in the back of the SMG Connection to Serial Device To connect a vehicle cradle for serial connectivity e g a printer 1 Using the RS 232 cable insert the 6 pin connector in the port on the base of the cradle Insert the other connector in the serial port on the other device Quick Reference Placing the PPT 4600 in the Cradle To place the PPT 4600 in the VCD 4612 For a full screen terminal remove the clips from the lower Note holding bracket before seating the terminal Slide the terminal base in behind the lower holding bracket and snap the terminal back in one motion The wings automatically slide over the 4600 s shoulders to secure the unit in position Note Do NOT pull up on the wings to lay the terminal in the cradle The unit is
10. rging immediately 4 Check the cradle LEDs to determine the spare pack s charging status Quick Reference e Ifthe Spare Battery Charge LED is amber the pack is still charging and should not be used e The LED toggles between amber and green when the pack is close to being fully charged e When the LED changes to green the battery pack is fully charged When the pack is fully charged remove the battery from the charging slot Depress the battery pack release switch and lift the pack out of the charging slot Quick Reference Indicator Lights LED LED Color Cradle Power LED Green Power on Cradle Battery Charging LED Green Spare battery in cradle slot is fully charged OR No spare battery in cradle Amber Spare battery charging Amber lt gt Green Spare battery is ALMOST fully charged Terminal Battery Charging LED Amber Battery pack in terminal is charging Amber lt gt Green Spare battery is ALMOST fully charged Green Battery pack in terminal is fully charged Terminal COMM LED Off Cradle mode disabled and or terminal not in cradle Solid Green Cradle mode enabled and terminal in cradle Terminal not controlling the bus Flashing Green Cradle mode enabled and terminal in cradle Terminal is controlling the bus Quick Reference Troubleshooting Symptom No
11. s after being returned to Symbol by a carrier selected and paid for by the customer These provisions do not prolong the original warranty term for any product which has been repaired or replaced by Symbol This warranty applies to the original owner and does not extend to any product which has been subject to misuse neglect accidental damage unauthorized repair or tampering Preventive maintenance activities are not covered by warranty Quick Reference Patents This product is covered by one or more of the following U S and foreign Patents U S Patent No 4 360 798 4 369 361 4 387 297 4 460 120 4 496 831 4 593 186 4 603 262 4 607 156 4 652 750 4 673 805 4 736 095 4 758 717 4 816 660 4 845 350 4 896 026 4 897 532 4 923 281 4 933 538 4 992 717 5 015 833 5 017 765 5 021 641 5 029 183 5 047 617 5 103 461 5 113 445 5 130 520 5 140 144 5 142 550 5 149 950 5 157 687 5 168 148 5 168 149 5 180 904 5 229 591 5 230 088 5 235 167 5 243 655 5 247 162 5 250 791 5 250 792 5 262 627 5 262 628 5 266 787 5 278 398 5 280 162 5 280 163 5 280 164 5 280 498 5 304 786 5 304 788 5 306 900 5 321 246 5 324 924 5 337 361 5 367 151 5 373 148 5 378 882 5 396 053 5 396 055 5 399 846 5 408 081 5 410 139 5 410 140 5 412 198 5 418 812 5 420 411 5 436 440 5 444 231 5 449 891 5 449 893 5 468 949 5 471 042 5 478 998 5 479 000 5 479 002 5 479 441 5 504 322 5 519 577 5 528 621 5 532 469 5 54
Download Pdf Manuals
Related Search