Supermicro
Contents
1. Figure 5 5 Installing the Hard Drive Carrier into the Hard Drive Cage 8 Insert the hard drive carrier into the hard drive cage sliding it towards the back of the the hard drive cage until it clicks into a locked position 9 If desired each hard drive carrier may be secured to the exterior of the hard drive cage using optional screws 10 Rotate the hard drive cage 90 degrees inward returning it to the closed operational position in the chassis 11 Connect the related cables to the hard drives Chapter 5 Chassis Setup and Maintenance 5 6 Installing the UO Shield and Motherboard The SC731 supports a micro ATX motherboard which is sold separately and comes with an I O shield specific to the motherboard UO Shield Figure 5 6 I O Shield Placement UO Shield An UO shield holds the motherboard ports in place Install the I O shield before you install the motherboard Installing the 1 0 Shield 1 Review the documentation that came with the motherboard Become familiar with component placement requirements and safety precautions 2 Disconnect the chassis from any power source 3 With the illustrations facing the outside of the chassis slide the shield into the space provided 4 Once installed the motherboard will hold the I O shield in place Permanent Motherboard Standoffs The SC731 provides permanent motherboard stan2. baaa 5 1 Removing Power from the System 5 1 Removing Bue 5 2 Rotating the Hard Drive Cage una 5 3 Removing and Installing Hard Drives sisne eanais 5 4 Installing the I O Shield and Motherboard neen eneen 5 7 VO Shieldi NES 5 7 Permanent Motherboard Standoffs Motherboard Installation t ter teet 5 8 Installing an Peripheral Device L L Eke keke kk kk ek KAS 5 9 Installing Expansion Cards sarria n nadiy ra xaney ard za teet ca 5 10 Long Expansion Card Setup oit reete ka 5 11 Installing the System Fan Installing the Front Bezel Power Supply Appendix A Cables Screws and Other Accessories Appendix B SC731 Power Supply Specifications vi Chapter 1 Introduction Chapter 1 Introduction 1 1 Overview Supermicro s SC731 chassis features a unique and highly optimized design allow ing most configuration of the chassis to be accomplished without tools or screws The chassis is equipped with high efficiency power supply High performance fans provide ample optimized cooling for FB DIMM memory modules and four hot swap drive bays offer maximum storage capacity 1 2 Shipping Lists Please visit the following link for the latest shiping lists and part numbers for your particular chassis model http www supermicro com products chassis tower chs 731 SC731 Chassis Model Drives UO Slots Power Supply 4x 3 5 300W SC731D 300B 2x 5 2
3. 7252 072201 ONIDV 192010 PW n 190 Tip i530 TINA p2950111 nan IN NIPAT 2199 181522 NOOI NN NP v 2 2 Chapter 2 Warning Statements for AC Systems Ann dal ef Guat ol Se Al Al ai ies je Dal es Sil gall ye Leal ll ale de Sila gl ule Dax l d AL yell Saal ga sl E Bs dl A gl GLa all A a ule 0S Lis All yaad US les ve paill Ghul af exsul EECH i ro p fijo BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwings symbool betekent gevaar U verkeert in een situatie die lichamelijk letsel kan veroorzaken Voordat u aan enige apparatuur gaat werken dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico s en dient u op de hoogte te zijn van de standaard procedures om ongelukken te voorkomen Gebruik de nummers aan het eind van elke waarschuwing om deze te herleiden naar de desbetreffende locatie BEWAAR DEZE INSTRUCTIES 2 3 SC731 Chassis Manual Installation Instructions A Warning Read the installation instructions before connecting the system to the power source eue TS ZER Beg DINE an FEE atb FEO PHAR ERE ce gt Hi A ES D HEAR G BECH Warnung Vor dem Anschlie en des Systems an die Stromquelle die Installationsanweisungen lesen iAdvertencia Lea las instrucciones de instalaci n antes de conectar el sistema a la red de alimentaci n Attention Avant de brancher le syst me sur la source d alimentation c
4. Diese Einheit ist zur Installation in Bereichen mit beschr nktem Zutritt vorgesehen Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug Schloss und Schl ssel oder einer sonstigen Sicherheitsvorkehrung m glich iAdvertencia Esta unidad ha sido dise ada para instalaci n en reas de acceso restringido S lo puede obtenerse acceso a una de estas reas mediante la utilizaci n de una herramienta especial cerradura con llave u otro medio de seguridad Attention Cet appareil doit tre install e dans des zones d acc s r serv s L acc s une zone d acc s r serv n est possible qu en utilisant un outil sp cial un m canisme de verrouillage et une cl ou tout autre moyen de s curit 2 9 SC731 Chassis Manual n 212 103 OY TIN LON nya nii TWA ma 02247 072 WW DRA mem ns ppna v 721 51135 DPE 7292 TNV 75 nb dll Ga jl ias Join yanadi gi als Bla plaste JAS ya da 5 Rana is el saa dl Sa OL 5 zal Aba s sl sl c Uia y J aa ol JAE duel AA FIN SAGES JINEYA STET te x B 7 He 7g ek Tz E SAA At AS Sol EI Wed Waarschuwing Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te maken van speciaal gereedschap slot en sleutel of andere veiligheidsmaatregelen Battery Handling A Warning There is the danger of explosion if the battery is replaced incorrectly Replac
5. components of the SC731 do not require tools or screws to set them up Those components which must be secured with screws require only a Phillips screwdriver 5 2 Removing Power from the System Before performing some setup or maintenance tasks use the following procedure to ensure that power has been removed from the system 1 Use the operating system to power down the system following the on screen prompts 2 After the system has completely shut down carefully grasp the head of the power cord and gently pull it out of the back of the power supply If your sys tem has dual power supplies remove the cords from both power supplies 3 Disconnect the cord from the power strip or wall outlet 5 1 SC731 Chassis Manual 5 3 Removing the Chassis Cover Cover Handle B o Slide Tab A Toward Handle B Figure 5 1 Removing the Chassis Cover Removing the Chassis Cover 1 Power down the system as described in Section 5 2 Slide the release tab A towards the cover handle B Grasp the cover handle with your fingers Slide the cover toward the rear of the chassis Remove the cover from the chassis Caution Except for short periods of time do not operate the server without the cover in place The chassis cover must be in place to allow proper airflow and prevent overheating 5 2 Chapter 5 Chassis Setup and Maintenance 5 4 Rotating the Hard Drive Cage Release Tab A HDD
6. n las instrucciones del fabricante TIAN rona v arpn R Ta 29901 172 299105 YW pis n130 NIP D nn n 013 ONINT 1102 129705 nx yon MRI 55 9399 v mwaiwan moon pIo Elei Asus j y play Lal Jac Alla il Ge jas dlia dy Lal A iriall AS Al 43 Oue d Les Lala Le gl E all akla L dla 4S LAN lala G y Aerial ol Hall ja al am Meer SHEA xxx Yen 29 930 EU 71E ME 2 Ss HN BASE ESS SHS Meijden aa ao ut az Y Hal ok 4230 AE el esr SAAL E Oh Waarschuwing Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt Vervang de batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd te worden 2 11 SC731 Chassis Manual Redundant Power Supplies A Warning This unit might have more than one power supply connection All connections must be removed to de energize the unit JURE TODAY dB EIR TD BEEN TW AUDIE Lzy ORZA DIEUX TN TORE INEEN x XI E V kr REES gt ADE m ERUIT Be IE IR AT S R I je Ee E V tz BEBE ITE TT ARA gt OI ERA Be Pr LE WERA EN E de Warnung Dieses Ger t kann mehr als eine Stromzufuhr haben Um sicherzustellen dass der Einheit kein trom zugef hrt wird m ssen alle Verbindungen
7. sur la s curit Mat riel interdit l utilisation de UL ou CSA c bles certifi s qui ont UL ou CSA indiqu sur le code pour tous les autres appareils lectriques que les produits d sign s par Supermicro seulement AC RX o gt awn gums WN AC PARNA D PDD 0 222 VANWA W WIA AN D PPNA WR IN top 01149 919 INN ONNA IN 525 bon WIW gt DW 129107 1791 TION OP mmo ppm Yawn 0922 sg PN D YY san xp Ow Tp DY VDM 3805 CSA 2 IN UL 2 550157 D 2222 vinum 292 PPD vm YY mms NAW INN YAWN 131 99 1129 UL CSA Asi E DUS ge Jm gill GUIS plast casa gal Cus yi aie aa Gell Jul CN saas Gijs A dhe d jan us 5 Y ga y A ai of uil cela Wine UL j CSA SUSI alaA las dada y sil al ya AG Sll 5 je I J ya Bacine Supermicro J ya Aia Casel A e A AL w 5 sl el UL CSA Aale Jami A 78 11 AFS AAE uou SAY AAA ADA IEA AAA ACH HEE l t Beh WE CHE elei HES WH LE le ade u VE A72 ELAN Electrical Appliance and Material Safety Law 2 4013949 JAH ASS Soe 1949 GS A7 FAES 8 ULEE CSAIA AGA del AA Ho UL CSA7E EA SA ARES aA gud ul de Waarschuwing Bij het installeren van het product gebruik de meegeleverde of aangewezen kabels stroomkabels en adapters Het gebruik van andere kabels en adapters kan leiden tot een storing of een brand Elektrisch apparaat en veiligheidsinformatiebladen wet verbiedt het gebruik van UL of CSA gecertificeerde kabels die UL of CSA die op de code voor andere ele
8. 23 TI BE 5 RES gt ER T Supe rmi c ro HE EN En EAM ARTI PEA E EE ARE UL OSA Jon gt SUN Leger CAE be DL Hr E BS f Y Warnung Bei der Installation des Produkts die zur Verf gung gestellten oder benannt Anschlusskabel Stromkabel und Netzteile Verwendung anderer Kabel und Adapter kann zu einer Fehlfunktion oder ein Brand entstehen Elektrische Ger te und Material Safety Law verbietet die Verwendung von UL oder CSA zertifizierte Kabel UL oder CSA auf der Code f r alle anderen elektrischen Ger te als Produkte von Supermicro nur bezeichnet gezeigt haben Advertencia Al instalar el producto utilice los cables de conexi n previstos o designados los cables y adaptadores de CA La utilizaci n de otros cables y adaptadores podr a ocasionar un mal funcionamiento o un incendio Aparatos El ctricos y la Ley de Seguridad del Material proh be el uso de UL o CSA cables certificados que tienen UL o CSA se muestra en el c digo de otros dispositivos el ctricos que los productos designados por Supermicro solamente 2 18 Chapter 2 Warning Statements for AC Systems Attention Lors de l installation du produit utilisez les bables de connection fournis ou d sign L utilisation d autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie Appareils lectrom nagers et de loi
9. 5 4x FF High efficiency 1x 3 5 for card reader e 4x 3 5 4x FF 300W dede 2x 5 25 High efficiency 1 1 SC731 Chassis Manual 1 3 Contacting Supermicro Headquarters Address Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A Tel 1 408 503 8000 Fax 1 408 503 8008 Email marketing supermicro com General Information support supermicro com Technical Support Web Site www supermicro com Europe Address Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands Tel 31 0 73 6400390 Fax 31 0 73 6416525 Email sales supermicro nl General Information support supermicro nl Technical Support rma supermicro nl Customer Support Web Site www supermicro com Asia Pacific Address Super Micro Computer Inc 3F No 150 Jian 1st Rd Zhonghe Dist New Taipei City 235 Taiwan R O C Tel 886 2 8226 3990 Fax 886 2 8226 3992 Email support supermicro com tw Tel 886 2 8226 3990 Web Site www supermicro com tw 1 2 Chapter 1 Introduction 1 4 Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required be fore any warranty service will be rendered You can obtain service by calling your vendor for a Returned Merchandise Authorization RMA number When returning to the manufacturer the RMA number should be prominently displayed on the outside of the shipping carto
10. Cage B Figure 5 2 Rotating the Hard Drive Cage In order to access and install components in the chassis interior it is necessary to rotate the hard drive cage This will provide sufficient room to install and configure the chassis components Rotating the Hard Drive Cage 1 Power down the system as described in Section 5 2 and remove the chassis cover 2 Lift the release tab A 3 Rotate the hard disk drive cage B outward 5 3 SC731 Chassis Manual 5 5 Removing and Installing Hard Drives Release Tabs Figure 5 3 Removing the Hard Drive Carrier from the Hard Drive Cage Removing and Installing Hard Drives 1 Power down the system as described in Section 5 2 and remove the chassis cover 2 Rotate the hard drive cage outward 90 degrees as described previously 3 Disconnect all of the cables from the hard drive 4 Press the release tab on the side of the hard drive carrier that is to be re moved from the hard drive cage 5 Gently slide the hard drive carrier out of the hard drive cage 5 4 Chapter 5 Chassis Setup and Maintenance Figure 5 4 Removing the Hard Drive from the Hard Drive Carrier 6 If a hard drive is already present remove it by carefully pulling the sides of the hard drive carrier outward 7 Insert the new hard drive into the hard drive carrier 5 5 SC731 Chassis Manual Optional Screws
11. Chassis Manual 5 11 Power Supply The SC731 chassis includes a 300 Watt power supply In the unlikely event that it becomes necessary to replace the power supply follow the instructions below Power Supply ef Figure 5 13 Removing the Power Supply Changing the Power Supply 1 Disconnect the chassis from any power source 2 Disconnect the motherboard cables 3 Remove the screws securing the power supply to the chassis which are located on the rear of the chassis Set these screws aside for later use 4 Gently lift the power supply out of the chassis 5 Replace the failed power supply with an identical power supply model 6 Secure the new power supply using the screws previously set aside 7 Plug the AC power cord back into the module and power up the server 5 14 Appendix A Chassis Cables Appendix A Cables Screws and Other Accessories A 1 Overview This appendix lists the supported cables for the SC731 chassis It only includes the most commonly used components and configurations For more compatible cables refer to the manufacturer of the motherboard and our Web site at www supermicro com A 2 Cables Included with SC731 Chassis SC731D 300B SC731i 300B Part Type Quantity Description CBL 0087 Cable 1 Front panel cable 16 pin
12. INT Dapp YAWN pn naxin ng nan TPE npn daleiall Ail gll y SIZAN al all Jar Of cas Aio w ll Glaeall Gus Y el je Sls 7 51 23449 2 572 37 1491 44 9 E 44319 uu Waarschuwing Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften Product Disposal A Warning Ultimate disposal of this product should be handled according to all national laws and regulations ROBES TOBE BERL DAA ID BURT SAC OEE RINGE LES E BEDS DUES RAL E CT Ar m J e EE IR DERT A ERAAN NT gt Ex A E CT EDERT EV EUX gt ATETI NE ER gt Warnung Die Entsorgung dieses Produkts sollte gem allen Bestimmungen und Gesetzen des Landes erfolgen SC731 Chassis Manual iAdvertencia Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales Attention La mise au rebut ou le recyclage de ce produit sont g n ralement soumis des lois et ou directives de respect de l environnement Renseignez vous aupr s de l organisme comp tent 55 pro rms msn PINT nma ONNA NPD 3 n AT 231 PU DID P12 0 Agile dl ei gil ul jill are li Ass Jalil Ar geel D ye All yal sie 73 51 e AS AS 3719 xp Wat B 1149 ue user 97 Waarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen Hot
13. SUPERG SC731 CHASSIS SERIES SC731D 300B SC731i 300B USER S MANUAL 1 0c The information in this User s Manual has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com Super Micro Computer Inc Supermicro reserves the right to make changes to the product described in this manual at any time and without notice This product including software if any and documentation may not in whole or in part be copied photocopied reproduced translated or reduced to any medium or machine without prior written consent IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any dis
14. Swap Fan Warning A Warning The fans might still be turning when you remove the fan assembly from the chassis Keep fingers screwdrivers and other objects away from the openings in the fan assembly s housing Vey RAT Y TO Zar DEN 7 END AUTRE 7 7 DETER U TOS REMO EK 3 TIO J FAN 354 OBI OZ EOU 7xvY C FEW EI BEN MESSE UR TI RE THE RNCS FE RE AI VK SET XUR 2 16 Chapter 2 Warning Statements for AC Systems E de El GE BECK SER ilg gt JEST E TI TEBI gt Iu ERD SH NET A Warnung Die L fter drehen sich u U noch wenn die L fterbaugruppe aus dem Chassis genommen wird Halten Sie Finger Schraubendreher und andere Gegenst nde von den ffnungen des L ftergeh uses entfernt iAdvertencia Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador del chasis Mandtenga los dedos los destornilladores y todos los objetos lejos de las aberturas del ventilador Attention Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez le bloc ventilateur du ch ssis Prenez garde ce que doigts tournevis et autres objets soient loign s du logement du bloc ventilateur mms V OTD 7779 DWNT TIN NAA MND Pon DA 0507 UND man TANI cnn ONW may 23 MYILRN AN MVI prin pmn ell casa IS ope a y yall AES AN 5 Ae sal JI ji e shall cl Sall e cl all Sis y TRAY As y pall AES
15. al device Slide the device into the chassis If desired screws may be used where indicated below B to secure the opti cal device into chassis Optional Screw B N Figure 5 8 Installing the Optical Device 5 9 SC731 Chassis Manual 5 8 Installing Expansion Cards The SC731 chassis includes four slots for expansion cards The number of cards you can use depends on your motherboard model Protective Bracket Figure 5 9 Locating the Expansion Card Installation Components Installing Expansion Cards 1 Depress the release latch A that holds the protective bracket B which secures the extension card brackets to the chassis Lower the protective bracket from over the top of the extension card dummy brackets as shown in the lower illustration Remove the dummy brackets from their slots Simultaneously slide the card and its bracket into the slot on the chassis and insert the card into its slot on the motherboard If desired screws can be used to secure the cards brackets to the chassis Close the protective bracket over the tops of the card brackets 5 10 Chapter 5 Chassis Setup and Maintenance Long Card Holders Figure 5 10 Installing a Long Expansion Card Long Expansion Card Setup The SC731 chassis includes clips to accomodate the use of long length expan sion cards These clips support and stabilize the long cards preventing them from contacting any undesi
16. amaged If the chassis itself shows damage file a damage claim with the carrier 3 3 Where to Get Replacement Components Infrequently you may need replacement parts for your system To ensure the highest level of professional service and technical support we recommend purchasing ex clusively from our Supermicro Authorized Distributors System Integrators Resellers A list of Supermicro Authorized Distributors System Integrators Resellers can be found at http www supermicro com Click the Where to Buy link 3 2 Chapter 4 System Interface Chapter 4 System Interface 4 1 Overview The chassis includes a control panel on the front that houses power buttons and status monitoring lights These elements are described in this chapter with possible responses Bes ie ste 2220 All in One Power Card Reader Button Power USB Ports Button o r c o E 6 000 oO 202 LEDs LEDs SC731D 300B SC731i 300B Figure 4 1 Front Chassis Panels 4 1 SC731 Chassis Manual 4 2 Control Panel Buttons Power The main power switch is used to apply or remove power from the power supply to the server system Turning off system power with this button removes the main power but keeps standby power supplied to the system Therefore you must unplug system before performing most maintenance tasks 4 3 Control Panel LED
17. doffs molded into the chassis floor These standoffs prevent short circuits by creating space between the moth erboard and the chassis surface 5 7 SC731 Chassis Manual Motherboard Installation Installing the Motherboard 1 Review the documentation that came with your motherboard Become familiar with component placement requirements precautions and cable connec tions Disconnect the chassis from any power source Rotate the hard drive cage 90 degrees outward Lay the motherboard in the chassis Secure the motherboard to the chassis using the rounded Phillips head screws provided Do not exceed eight inch pounds of torque when tightening the motherboard Secure the CPU s heatsinks and other components to the motherboard as described in the motherboard documentation Connect the cables between the motherboard and power supply e Figure 5 7 Installing the Motherboard 5 8 Chapter 5 Chassis Setup and Maintenance 5 7 Installing an Peripheral Device The SC731 chassis has two bays for peripheral devices such as a DVD drive Installing a Peripheral Device 1 Remove the front bezel from the chassis by lifting it upwards from the bottom and pulling off the front of the chassis Remove the cover plate from the bay on the front of the chassis Install the bracket rail A onto one side of the device by inserting the pins of the bracket into the mounting holes on the sides of the optic
18. e installation and use of the SC731 chassis Installation and maintenance should be performed by experienced technicians only Supermicro s SC731 chassis features a unique and highly optimized design allow ing the user to install components with minimal or no use of screws or tools The chassis is equipped with a 300 Watt whisper quiet high efficiency power supply for superb power savings This manual lists compatible parts available when this document was published Always refer to the our Web site for updates on supported parts and configurations at www supermicro com SC731 Chassis Manual Manual Organization Chapter 1 Introduction The first chapter provides a description of the main components included with this chassis and describes the main features of the SC731 chassis This chapter also includes contact information Chapter 2 Warning Statements for AC Systems This chapter lists warnings precautions and system safety It is recommended that you thoroughly familiarize yourself with the safety precautions before installing and servicing this chassis Chapter 3 System Interface Refer to this chapter for details on the system interface which includes the functions and information provided by the control panel on the chassis as well as other LEDs located throughout the system Chapter 4 Chassis Setup and Maintenance Follow the procedures given in this chapter when installing removing or reconfiguring your chassi
19. e the battery only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions iil MOR ENI APA ELST DIVE DIGIT BAO TET 450 ES SAT SEL X HEEF ZIEL KI O 5O 2e1 PE BPS O AA DTMAUT FEW Ex FB2U SE HEN TIBA YETA k Tg FD TSS HE ER SRE HER HII UTR TH ABI rot HRABE gt IAEA H E gt ra ZE E HATE AREER gt HAN fu AL EE EE ET Al Ge EI THIS BCE TH d AJ EE E AR 2 10 Chapter 2 Warning Statements for AC Systems Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers Attention Danger d explosion si la pile n est pas remplac e correctement Ne la remplacer que par une pile de type semblable ou quivalent recommand e par le fabricant Jeter les piles usag es conform ment aux instructions du fabricant iAdvertencia Existe peligro de explosi n si la bater a se reemplaza de manera incorrecta Reemplazar la bater a exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante Desechar las bater as gastadas seg
20. ei der Wartung iAdvertencia Cuando el sistema est en funcionamiento el voltaje del plano trasero es peligroso Tenga cuidado cuando lo revise Attention Lorsque le syst me est en fonctionnement des tensions lectriques circulent sur le fond de panier Prendre des pr cautions lors de la maintenance 2 13 SC731 Chassis Manual nrs 5353 nnn rms 72902 Ann v no yan 91990 para AND 2192 nn n150 nip max A slll cle Basa sall ABUSE sf Aa ESH LA Gye jha lua Zeal Jae Lans Ae yaa CS dJ el BA Ss aie 73 1 NARO 52 EA d FER Backplane E AAF AH epu z way Bd AMA 4 Soa Waarschuwing Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het systeem in gebruik is Voorzichtigheid is geboden tijdens het onderhoud Comply with Local and National Electrical Codes Warning Installation of the equipment must comply with local and national electrical codes HIT UT OD ABU PERO EU CE DHS UMD EEN ab E P We n ZED EAS A TH EES EL B SEDE AAA RA e Warnung Die Installation der Ger te muss den Sicherheitsstandards entsprechen iAdvertencia La instalacion del equipo debe cumplir con las normas de electricidad locales y nacionales Chapter 2 Warning Statements for AC Systems Attention L quipement doit tre install conform ment aux normes lectriques nationales et locales zin YAWN pin DNN gums JOP S
21. entfernt werden Advertencia Puede que esta unidad tenga m s de una conexi n para fuentes de alimentaci n Para cortar por completo el suministro de energ a deben desconectarse todas las conexiones Attention Cette unit peut avoir plus d une connexion d alimentation Pour supprimer toute tension et tout courant lectrique de l unit toutes les connexions d alimentation doivent tre d branch es SAN GD n D P ax mmu TPN naa Dy aman bo pg von v 290 20 308 mno nv v mm APT DN 2 12 Chapter 2 Warning Statements for AC Systems AGUA aal lan sa Y LA ae jal lid So A el ll e as al dal ONLY AUS ATI 5 casa 7A at o BANS RA olde AA FE HAT AAs MS UE ol BAe AAL AU AAT LE AA UAE amore quu Waarschuwing Deze eenheid kan meer dan n stroomtoevoeraansluiting bevatten Alle aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken Backplane Voltage A Warning Hazardous voltage or energy is present on the backplane when the system is operating Use caution when servicing NIFV DEE ZAT LORDS SERIE EE FAKTEN DN ITU bizo C353 EERS DENKER EL HRAT gt HIR E HIRE KIN HR HE gt DEPTH HD Ns gt r1 ARIEL HIR EERE ME BI gt HEATHER e Warnung Wenn das System in Betrieb ist treten auf der R ckwandplatine gef hrliche Spannungen oder Energien auf Vorsicht b
22. ents for AC Systems jAdvertencia El sistema debe ser disconnected de todas las fuentes de energia y del cable el ctrico quitado de los m dulos de fuente de alimentaci n antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema Attention Le syst me doit tre d branch de toutes les sources de puissance ainsi que de son cordon d alimentation secteur avant d acc der l int rieur du chassis pour installer ou enlever des composants de syst me wad paona san 525 nx Pon 09 Dawn nmpn 229 0997 NN pI v 022231 0305 AN nipna TNE msn b e man pon nu 10 Yael bas y yo oly w ll Al AN 5 ELAN An aren pe aUaill ued Gas J AULII les c la Sa AI del Ball Aa AHA A J gt d AAW FEE Wap sp see use dcs en A HEEN AU DIAZ dads BE AAW ANTES Bellot Waarschuwing Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren of verwijderen van systeem onderdelen dient u alle spanningsbronnen en alle stroomkabels aangesloten op de voeding en van de behuizing te verwijderen 2 7 SC731 Chassis Manual Equipment Installation A Warning Only trained and qualified personnel should be allowed to install replace or service this equipment Fan OD ent E 27725205 BENE ANI TAC O B FLO Hit SER Fiel EA if nf ANTUOKT AREA ERFAHREN DT BETTER eS gt EE gt RARGH alll LAA AA TEE ERRE Tha ti Warnun
23. g Das Installieren Ersetzen oder Bedienen dieser Ausr stung sollte nur geschultem qualifiziertem Personal gestattet werden jAdvertencia Solamente el personal calificado debe instalar reemplazar o utilizar este equipo Attention ll est vivement recommand de confier l installation le remplacement et la maintenance de ces quipements des personnels qualifi s et exp riment s TINTIN TPA hay NW nnb IN 3135 nW PYNT ppnnd RWI 1292 now nm Joli a Lans A Sail y 2 Oe nelle Cale gall cils sall L raus Of ay o H EUS da Edu ate o hu 2 BA MA EE MAS FMS su Chapter 2 Warning Statements for AC Systems Waarschuwing Deze apparatuur mag alleen worden ge nstalleerd vervangen of hersteld door geschoold en gekwalificeerd personeel Restricted Area A Warning This unit is intended for installation in restricted access areas A restricted access area can be accessed only through the use of a special tool lock and key or other means of security This warning does not apply to workstations 727 AU BR bek 2O22 HE ts ZIEK kle HEE NZ RL CL E TI AB HL KEE ID BEE DEN TOMO LA SUT4 0 TER UL TO AH HANETT ga PESTEN DE DUE LB APTE RAE ao a gt BIRI PRET e T BELT SUR a A ERASE il EA JA EA HI E Je TR TERE DAR 7K BAA REEN NER e Warnung
24. ktrische apparaten dan de producten die door Supermicro alleen 2 19 SC731 Chassis Manual Notes 2 20 Chapter 3 Components Chapter 3 Chassis Components This chapter describes some common components included with your chassis For the latest information and shipping lists visit http www supermicro com 3 1 Components Drive Bays The chassis supports all of the below Four 3 5 SAS SATA internal drive trays SAS or enterprise SATA hard disk drives are recommended Hard drives must be purchased separately Two 5 25 external bays that can house additional hard drives removable media drives or other peripheral drives One 3 5 external bay that can house a card reader additional hard drives or other peripheral drives Motherboard Support The maximum motherboard size is 9 6 x 9 6 micro ATX supporting Intel and AMD single processors Power Supply Each chassis includes a high efficiency power supply The 300W unit has an 80 Bronze level certification Fans The chassis includes a 9cm rear fan with 25db whisper quiet operation and an optional 8cm front fan 3 1 SC731 Chassis Manua UO Expansion slots The chassis includes four full height full length I O expansion slots Switches and Status Indicators The chassis includes a convenient power switch and LED status indicators 3 2 Unpacking the System Inspect the box in which the chassis was shipped and note if it was d
25. ls ll ye lazer clad jo la pue y Zal MAENE d AVES AAE xus sue AVE PREEK eeu Aan Erpel IMA FA BES dall LAAR Waarschuwing Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het ventilatorsamenstel uit het chassis Houd uw vingers schroevendraaiers en eventuele andere voorwerpen uit de buurt van de openingen in de ventilatorbehuizing 2 17 SC731 Chassis Manual Power Cable and AC Adapter A Warning When installing the product use the provided or designated connection cables power cables and AC adaptors Using any other cables and adaptors could cause a malfunction or a fire Electrical Appliance and Material Safety Law prohibits the use of UL or CSA certified cables that have UL CSA shown on the code for any other electrical devices than products designated by Supermicro only WPI REACT A7 A BEDELS SAA VRK JA JR SET TV FER REACT RT A ZIEH P amp O DT 7 6o7y 27 ARENT DE NEP R RO ANITA DES EUH mL RTE ULE 7 IRAN CO ie 7 JW UL CSEv 775a FICK oU Supermicro fH FS ADU MEETS S c LC SL TOES ZERE aft TE GEH AS Er pe DE SUR EB XE BARA EO PA EEN an GEM H HE de ol BESS Ee HE OX gt ERY Supe rmi c roffa EAI am BSH All A TEE ELIE ZA IE BE FHZRZEULERCSATA ERIBA RM FAH RUL CSARFS Ee zi H x A E Ta 6 HE FE ZI D EA GH EA ERA EEE es Sl FE Ti zk Ri JN
26. micro chassis These warnings may also be found on our web site at http www supermicro com about policies safety information cfm Warning Definition A Warning This warning symbol means danger You are in a situation that could cause bodily injury Before you work on any equipment be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents BEDEK WET Sf PVE XEWE LES NEELIE RIED BO 370 C d TUO MER C LINER Bite SACA EEE EPA BH LE JN DM U FEU TS AER o EEM FREZEN ER D EE EADE LEGGEN UE LE Z BE gt AAI SUUS FERNS SED LFRREN DELIFER ARE EE EES AE EEE SEE ZE s ERE LUI A e HEEE gt AE RE SAE TI RE IR LIFE gt TERA Ea ZA HI XERA FRAY abe gt PATS ADT AEE AE gt AR ESR HERE AGA EN ERHAN gt I en SC731 Chassis Manual Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr Sie befinden sich in einer Situation die zu Verletzungen f hren kann Machen Sie sich vor der Arbeit mit Ger ten mit den Gefahren elektrischer Schaltungen und den blichen Verfahren zur Vorbeugung vor Unf llen vertraut Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisu
27. n and mailed prepaid or hand carried Shipping and handling charges will be applied for all orders that must be mailed when service is complete For faster service RMA authorizations may be requested online http www super micro com support rma Whenever possible repack the chassis in the original Supermicro carton using the original packaging material If these are no longer available be sure to pack the chassis securely using packaging material to surround the chassis so that it does not shift within the carton and become damaged during shipping This warranty only covers normal consumer use and does not cover damages in curred in shipping or from failure due to the alteration misuse abuse or improper maintenance of products During the warranty period contact your distributor first for any product problems 1 3 SC731 Chassis Manual Notes Chapter 2 Warning Statements for AC Systems Chapter 2 Standardized Warning Statements for AC Systems 2 1 About Standardized Warning Statements The following statements are industry standard warnings provided to warn the user of situations which have the potential for bodily injury Should you have questions or experience difficulty contact Supermicro s Technical Support department for assistance Only certified technicians should attempt to install or configure components Read this appendix in its entirety before installing or configuring components in the Super
28. ngsnummer nach der jeweiligen bersetzung in den bersetzten Sicherheitshinweisen die zusammen mit diesem Ger t ausgeliefert wurden BEWAHREN SIE DIESE HINWEISE GUT AUF INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este s mbolo de aviso indica peligro Existe riesgo para su integridad f sica Antes de manipular cualquier equipo considere los riesgos de la corriente el ctrica y familiar cese con los procedimientos est ndar de prevenci n de accidentes Al final de cada advertencia encontrar el n mero que le ayudar a encontrar el texto traducido en el apartado de traducciones que acompafia a este dispositivo GUARDE ESTAS INSTRUCCIONES IMPORTANTES INFORMATIONS DE S CURIT Ce symbole d avertissement indique un danger Vous vous trouvez dans une situation pouvant entra ner des blessures ou des dommages corporels Avant de travailler sur un quipement soyez conscient des dangers li s aux circuits lectriques et familiarisez vous avec les proc dures couramment utilis es pour viter les accidents Pour prendre connaissance des traductions des avertissements figurant dans les consignes de s curit traduites qui accompagnent cet appareil r f rez vous au num ro de l instruction situ la fin de chaque avertissement CONSERVEZ CES INFORMATIONS mmus nns mpn moan 155 wanwan DN vum nio YY WYND 320 9 by nma 79 mikan nmn n nn Dap oy Wp mx v 9093 m yan 012207 IN NRW v TTPA NWR MPD pasan DN 77419 IN Pena PRVI
29. onsulter les directives d installation nna pn NIN mmn 7159 nona nmm nx RP v AGUA une col AUS Jae gi Ud cas jill cul il NAGS Ado Ads do 24 UE erred filo Waarschuwing Raadpleeg de installatie instructies voordat u het systeem op de voedingsbron aansluit 2 4 Chapter 2 Warning Statements for AC Systems Circuit Breaker A Warning This product relies on the building s installation for short circuit overcurrent protection Ensure that the protective device is rated not greater than 250 V 20 A poy hI COD LS RARE QI EURO EECH PRETO ERA 250 V 20 AZERA OTE ZIRA PEW HEP EI SLR jD PRI EN BR SCHE Ta RA PRP DE HL RAAF 250V 20A aras BEZET IES GER En PRESE EH ESE PIA DESEE Aa fe De D TEPKA OR AT EE MAAN 250V 20A Warnung Dieses Produkt ist darauf angewiesen dass im Geb ude ein Kurzschluss bzw berstromschutz installiert ist Stellen Sie sicher dass der Nennwert der Schutzvorrichtung nicht mehr als 250 V 20 A betr gt jAdvertencia Este equipo utiliza el sistema de protecci n contra cortocircuitos o sobrecorrientes del edificio Aseg rese de que el dispositivo de protecci n no sea superior a 250 V 20 A Attention Pour ce qui est de la protection contre les courts circuits surtension ce produit d pend de l installation lectri
30. putes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Super Micro s total liability for all claims will not exceed the price paid for the hardware product California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warn ing applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate WARNING Handling of lead solder materials used in this product may expose you to lead a chemical known to the State of California to cause birth defects and other repro ductive harm Manual Revision 1 0c Release Date January 21 2014 Unless you request and receive written permission from Super Micro Computer Inc you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2014 by Super Micro Computer Inc All rights reserved Printed in the United States of America Preface Preface About This Manual This manual is written for professional system integrators and PC technicians It provides information for th
31. que du local V rifiez que le courant nominal du dispositif de protection n est pas sup rieur 250 V 20 A 5 xm v an p nian 071292 npn mun Yy TND AT 3372 250 V 20 A 15 IP R NIT YAWN EPT 352 1150 TWIN Leift Ai B w ll il gall Cu Adan lame le dins all D 2 20A 250V ie IST oel EN Ll andi Gh ge ast 2 5 SC731 Chassis Manual AX o ale 1499 Sha AJ el NN dao de wa AA Saul gs BA REEN 250V E 20A 0AE SEA EE ot Ht Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging overspanning van uw electrische installatie Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 220V 20A Power Disconnection Warning A Warning The system must be disconnected from all sources of power and the power cord removed from the power supply module s before accessing the chassis interior to install or remove system components EMUO RS ZAT ANR POMO NETO ALO RDA Var M ILA FAA VAFLOEPUET SN Y ARDEN el FIERE SO NT BRMBOET me FATE EAS ER DORA SE RTE JETER ARE At ESL ERAS RATA DAR ARTE gt REMER Warnung Das System muss von allen Quellen der Energie und vom Netzanschlusskabel getrennt sein das von den Spg Versorgungsteilmodulen entfernt wird bevor es auf den Chassisinnenraum zur ckgreift um Systemsbestandteile anzubringen oder zu entfernen 2 6 Chapter 2 Warning Statem
32. red surfaces Installing Long Expansion Cards 1 Locate the long card holders A on the opposite side of the chassis from the card brackets 2 Begin by installing the long card as described in the previous section 3 Push the long card holder all the way down onto the end of the card to se cure it in the chassis 5 11 SC731 Chassis Manual 5 9 Installing the System Fan Figure 5 11 Installing the System Fan The SC731 includes a super quiet system fan that provides cooling for the chassis No tools or screws are required to install the system fan Installing the System Fan 1 Disconnect all power to the chassis 2 Insert the four rubber pins into the four mounting holes surrounding the fan grill on the rear of the chassis 3 Place the system fan on top of the fan grill aligning the mounting holes of the fan grill with the mounting holes of the system fan 4 Pull the rubber pins through the mounting holes of the system fan to secure the fan to the chassis 5 Connect the fan cable to the motherboard 5 12 Chapter 5 Chassis Setup and Maintenance 5 10 Installing the Front Bezel Front Bezel Installation Remove the dummy cover A for peripheral device from the front bezel d 2 Push the front bezel onto the front of the chassis Remove the Dummy Cover A Figure 5 12 Installing the Front Bezel 5 13 SC731
33. s Appendix A Chassis Cables Screws and Other Accessories Appendix B Power Supply Specifications Preface Contents Chapter 1 Introduction E 1 2 1 3 1 4 Overview Shipping d E i e enden ne E E aa AN 1 1 Go nlacling S p Fl O EE 1 2 Returning Merchandise for Service 1 3 Chapter 2 Standardized Warning Statements for AC Systems 2 1 About Standardized Warning Statements keke 2 1 Waning eu 2 1 Installation Instructions 2 4 Circuit EE 2 5 Power Disconnection Warning essen an 2 6 Equipment EE Le TEE Restricted E Battery Handling tine arena ae Redundant Power Supplies Backplane e Te E Comply with Local and National Electrical Codes nennen 2 14 Product Disposal ici eer ente atn Ak AE k Ha k k Ak H ka eens 2 15 Hot Swap Fan W rning E 2 16 Power Cable and AC Adapter LE kek kek K k nnne 2 18 Chapter 3 Chassis Components 3 1 3 2 3 3 VO Expan Le Ee 3 2 Switches and Status Indicators 3 2 Unpacking N SV SIG T E 3 2 Where to Get Replacement Components keke 3 2 Chapter 4 System Interface 4 1 4 2 4 3 ONT 4 1 Control Panel B ttOns iii dE 4 2 ControlP nel LEDS Seconds ERE vae EEGEN ka TIE 4 2 Overheating SC731 Chassis Manual Chapter 5 Chassis Setup and Maintenance 5 1 5 2 5 3 5 4 5 5 5 6 5 7 5 8 5 9 5 10 5 11 OVE IU
34. s There are three LEDs that provide status information about the system HDD Indicates activity on the HDDS or peripheral drives when flashing E NIC1 Indicates network activity when flashing 4 2 Chapter 4 System Interface O 0 Information LED Alerts operator of several states as noted in the table below Information LED Status Description An overheat condition has occured EE This may be caused by cable congestion Blinking red 1Hz Fan failure check for an inoperative fan Blinking red 0 25Hz Power failure check for a non operational power supply Local UID has been activated Use this function to locate Solid blue the server in a rack mount environment Blinking blue Remote UID is on Use this function to identify the server from a remote location Overheating There are several possible responses if the system overheats If the system overheats 1 Use the LEDs to determine the nature of the overheating condition 2 Confirm that the chassis cover is installed properly 3 Check the routing of the cables and make sure all fans are present and operat ing normally 4 Verify that the heatsinks are installed properly 4 3 SC731 Chassis Manual Notes Chapter 5 Chassis Setup and Maintenance Chapter 5 Chassis Setup and Maintenance 5 1 Overview This chapter covers the steps required to install components and perform main tenance on the chassis Most
35. tical systems whose failure to per form be reasonably expected to result in significant injury or loss of life or catastrophic property damage Accordingly Supermicro disclaims any and all liability and should buyer use or sell such products for use in such ultra hazardous applications it does so entirely at its own risk Furthermore buyer agrees to fully indemnify defend and hold Supermicro harmless for and against any and all claims demands actions litigation and proceedings of any kind arising out of or related to such ultra hazardous use or sale B 2
36. to 16 pin CBL 0263L Cable 1 USB cable SC731i only CBL 0084L Cable 1 Split converter cable A 1 SC731 Chassis Manual A 3 Chassis Screws The accessory box includes all the screws needed to set up your chassis This section lists and describes the most commonly used screws Your chassis may not require all of the parts listed M B HARD DRIVE 2 Pan head Flat head 6 32 x 5 mm 6 32 x 5 mm 0 197 0 197 DVD ROM CD ROM and FLOPPY DRIVE g y Pan head Flat head Round head Round head 6 32x 5 mm 6 32 x 5 mm M3 x5 mm M2 6 x 5 mm 0 197 0 197 0 197 0 197 M B STANDOFFS M B standoff 6 32 to 6 32 A 2 Appendix B Power Supply Specifications Appendix B SC731 Power Supply Specifications This appendix lists power supply specifications for your chassis system The SC731 chassis includes a power supply rated at 80 Plus Bronze Level BRONZE Bronze Level 80 PLUS Certified Power Supplies SC731D 300B SC731i 300B 300W with PFC MER Part PWS 305 PQ Input 100 127 200 240Vac A 5A 50 60Hz 5V 19 Amps 12V 11 Amps 12Vcpu 11 5 Amps 3 3V 16 Amps 12V 0 15 Amps 5Vaux 2 Amps B 1 SC731 Chassis Manual Disclaimer cont The products sold by Supermicro are not intended for and will not be used in life sup port systems medical equipment nuclear facilities or systems aircraft aircraft devices aircraft emergency communication devices or other cri
Download Pdf Manuals
Related Search