SC933/SC833 Air Shroud User`s Guide
Contents
1. SC933 833 osscssazs xxonconr ose R A A la la The SC933 SC833 air shroud is customizable into a single configuration for 3U Supermicro SC933 SC833 series chassis systems see Figure 3 4 and Table 3 2 for details Table 3 2 SC933 SC833 Air Shroud Configurations Configuration Description Component parts A and D are attached for Intel Xeon DP 5500 5400 5100 5000 Configuration 1 12 x 13 form factor mainboards with 6 PCI slots and 12 8 4 memory DIMM slots optimized for use with Supermicro X7Dxx X8Dxx series mainboards 3 4 Chapter 3 Configuration and Installation 3 5 Installing the SC933 SC833 Air Shroud To install the SC933 SC833 air shroud follow the procedure below This procedure is the same for all configurations of the SC933 SC833 air shroud in 3U systems Installing the SC933 SC833 Air Shroud in SC933 SC833 Chassis Systems 1 Configure the air shroud to fit in your system See Section 3 4 for details on configuring the air shroud 2 Secure the forward edge of the SC933 SC833 to the forward part of the chassis interior so that the SC933 SC833 mounting tabs are locked in with the mounting slots of the chassis see Figure 3 5 Figure 3 5 Inserting Air Shroud onto a System Mainboard Component Part A Mounting Tabs Mounting Slots in Top Front Edge of Chassis Interior 3 52. SC933 SC833 Air Shroud User s Guide 3 Make sure the SC933 SC833 air shroud is mounted directly on the mainboard of its system so that the air shroud covers the system mainboard over the CPU s and memory slots see Figure 3 6 Figure 3 6 Air Shroud Mounted in System m m I fn Attach Securely Mount Flush with to Chassis Power Supply NOTE The air shroud should be mounted flush with the power supply housing f if installing properly and that some cable is supposed to go under the air shroud 4 Secure the top cover back on your system 3 6 Disclaimer The products sold by Supermicro are not intended for and will not be used in life support systems medical equipment nuclear facilities or systems aircraft aircraft devices aircraft emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage Accordingly Supermicro disclaims any and all liability and should buyer use or sell such products for use in such ultra hazardous applications it does so entirely at its own risk Furthermore buyer agrees to fully indemnify defend and hold Supermicro harmless for and against any and all claims demands actions litigation and proceedi
3. away from the system or on a table so that they won t accidentally be stepped on e While working on the system do not wear loose clothing such as neckties and unbuttoned shirt sleeves which can come into contact with electrical circuits or be pulled into a cooling fan Remove any jewelry or metal objects from your body which are excellent metal conductors that can create short circuits and harm you if they come into contact with printed circuit boards or areas where power is present After accessing the inside of the system replace the blade module s cover before installing it back into the blade enclosure 2 3 Electrostatic Discharge Precautions Electrostatic discharge ESD is generated by two objects with different electrical charges coming into contact with each other An electrical discharge is created to neutralize this difference which can damage electronic components and printed circuit boards The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD Use a grounded wrist strap designed to prevent static discharge Keep all components and printed circuit boards PCBs in their antistatic bags until ready for use e Touch a grounded metal object before removing the board from the antistatic bag Do not let components or PCBs come into contact with your clothing which may retain a charge even if you are wearing a wrist strap Hand
4. of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Super Micro s total liability for all claims will not exceed the price paid for the hardware product FCC Statement This eguipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the eguipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instruction manual may cause harmful interference with radio Communications Operation of this eguipment in a residential area is likely to cause harmful interference in which case you will be reguired to correct the interference at your own expense California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warning applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate for further details WARNING HANDLING OF LEAD SOLDER MATERIALS USED IN THIS A PRODUCT MAY EXPOSE YOU TO LEAD A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM Manual Revison 1 0 Re
5. optimized for use with Supermicro SC933 SC833 series chassis designs and for Supermicro X8Dxx X7Dxx series mainboards See Chapter 3 for configuration details 1 2 Product Checklist of Typical Components The SC933 SC833 air shroud comes packaged with components and parts as shown in Table 1 1 Table 1 1 SC933 SC833 Air Shroud Parts and Components Part Number Description Quantity MCP 310 38002 0N SC933 SC833 Intel DP plastic air shroud supports up to 12 memory DIMM slots MCP 310 38005 1N SC933 SC833 X8 air shroud component part A 1 MCP 310 28006 1N X8 air shroud universal component part D tear drop Mylar module 2 2 55mm wide 1 NOTE Each individual part for the SC933 SC833 air shroud is labeled with its f component part letter for easy identification 1 1 SC933 SC833 Air Shroud User s Guide 1 3 Features The SC933 SC833 air shroud includes the following features e Main air shroud component One detatchable component for multiple configurations e Breakable section for power cable management e Clear plastic material construction for ease of viewing 1 4 Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered You can obtain service by calling your vendor for a Returned Merchandise Authorization RMA number When returning to the manufacturer the RMA number should be prominently displayed on
6. 390 31 0 73 6416525 sales supermicro nl General Information support supermicro nl Technical Support rma supermicro nl Customer Support Super Micro Computer Inc 4F No 232 1 Liancheng Rd Chung Ho 235 Taipei County Taiwan R O C 886 2 8226 3990 886 2 8226 3991 www supermicro com tw support supermicro com tw 886 2 8228 1366 ext 132 or 139 SC933 SC833 Air Shroud User s Guide Notes Chapter 2 System Safety Please read and follow all safety precautions below before using your Supermicro product 2 1 Electrical Safety Precautions Basic electrical safety precautions should be followed to protect yourself from harm and the server from damage Be aware of how to power on off the enclosure power supplies and the individual blades as well as the room s emergency power off switch disconnection switch or electrical outlet If an electrical accident occurs you can then quickly remove power from the system Do not work alone when working with high voltage components Power should always be disconnected from the blade module when removing or installing such system components as the mainboard memory modules and processors When working around exposed electrical circuits another person who is familiar with the power off controls should be nearby to switch off the power if necessary Use only one hand when working with powered on electrical equipment This is to avoid making a complete ci
7. SUPERMICR SC933 SC833 Air Shroud User s Guide Revison 1 0 SC933 SC833 Air Shroud User s Guide The information in this User s Guide has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com Super Micro Computer Inc Supermicro reserves the right to make changes to the product described in this manual at any time and without notice This product including software if any and documentation may not in whole or in part be copied photocopied reproduced translated or reduced to any medium or machine without prior written consent IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer and customer shall be governed by the laws
8. Vi W ese ee ee iris 1 1 1 2 Product Checklist of Typical Componen e 1 1 1 S Eeature8 n hin alain anti Ge EG Deed 1 2 1 4 Returning Merchandise for Service 1 2 1 5 Contacting Supermicro ee ee se ek ee Ge GR Re Ge GR RR Ge Ge RR Ge Re 1 3 Chapter 2 System Safety 2 1 2 1 Electrical Safety Precauti0nS ese see ee ee ee RR Re ee GR GR ER ee Ge GR Re 2 1 2 2 General Safety Precautions 2 2 2 3 Electrostatic Discharge Precautions U 2 2 2 4 Operating Precautions 2 2 Chapter 3 Configuration and Installation 3 1 3 l OVEFVISW EE RE EE N 3 1 3 2 SC933 SC833 Air Shroud Components EEEEEEE 3 1 3 3 Removing Breakable Sections for Cabling 3 3 3 4 Configuring the SC933 SC833 Air Shroud 3 4 3 5 Installing the SC933 SC833 Air Shroud ee ee ee ee RR Re 3 5 SC933 SC833 Air Shroud User s Guide Notes Vi Chapter 1 Introduction 1 1 Overview The SC933 SC833 air shroud is a configurable air shroud for system mainboards to enable maximum efficient air flow through the system It can be configured to fit different sized Intel Xeon DP 5500 5400 5100 5000 series system mainboards of the same general shape and size The SC933 SC833 air shroud is
9. le a board by its edges only do not touch its components peripheral chips memory modules or contacts e When handling chips or modules avoid touching their pins Put the mainboard and peripherals back into their antistatic bags when not in use For grounding purposes make sure the blade enclosure provides excellent conductivity between the power supplies the blade modules and the mainboard 2 4 Operating Precautions Care must be taken to assure that the cover of the blade unit is in place when the blade is operating to assure proper cooling Out of warranty damage to the blade can occur if this practice is not strictly followed Any drive carrier without a hard drive installed must remain fully installed in the drive bay when the blade module is operating to ensure proper airflow 2 2 Chapter 3 Configuration and Installation 3 1 Overview This chapter covers the configuration and installation of the SC933 SC833 air shroud into a server or into a chassis The main section component part A can be connected to component part D to make a single configuration 3 2 SC933 SC833 Air Shroud Components Figure 3 1 SC933 SC833 Air Shroud Components Table 3 1 SC933 SC833 Air Shroud Components Item Description A SC933 SC833 X7 X8 air shroud component part A D X8 air shroud universal component part D tear drop Mylar module 2 2 55mm wide The SC933 SC833 air shroud comes with one detachable comp
10. lease Date April 27 2009 Unless you request and receive written permission from Super Micro Computer Inc you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2009 by Super Micro Computer Inc All rights reserved Printed in the United States of America Preface About this Manual This manual is written for professional system integrators Information Technology professionals service personnel and technicians It provides information for the installation and use of Supermicro s SC933 SC833 air shroud Installation and maintenance should be performed by experienced professionals only Manual Organization Chapter 1 Introduction The first chapter provides a checklist of the main components included with the SC933 SC833 air shroud and describes its main features Chapter 2 System Safety You should familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SC933 SC833 air shroud Chapter 3 Configuration and Installation Refer here for details on installing the SC933 SC833 air shroud on a computer system mainboard SC933 SC833 Air Shroud User s Guide Notes Table of Contents Chapter 1 Introduction 1 1 1 1 OVer
11. ngs of any kind arising out of or related to such ultra hazardous use or sale SC933 SC833 Air Shroud User s Guide Notes
12. onent Figure 3 1 and Table 3 1 See below for details on these various components These components create a single configuration for use in Intel Xeon DP 5500 5400 5100 5000 series systems The SC933 SC833 air shroud is optimized for use with Supermicro X8Dxx and X7Dxx series mainboards See Section 3 4 for further details on configurations 3 1 SC933 SC833 Air Shroud User s Guide Component Part D Figure 3 2 Component Part D _7 Component Part A a Alignment Slots The SC933 SC833 air shroud s component part D 2 2 55mm wide tear drop Mylar module see Figure 3 2 can be mounted on the underside of component part A by inserting its locking tabs into the component part A alignment slots provided It detaches by pushing component part D forward and then down as shown in the figure Chapter 3 Configuration and Installation 3 3 Removing Breakable Sections for Cabling Figure 3 3 Removing the Breakable Tabs Breakable Tabs Component part A for the SC933 SC833 air shroud has breakable tabs on its bottom that can be permanently removed to allow cabling access if required for your system To remove simply cut or break the tabs off from their attachments with a pair of scissors and discard them SC933 SC833 Air Shroud User s Guide 3 4 Configuring the SC933 SC833 Air Shroud Figure 3 4 SC933 SC833 Air Shroud Configuration
13. rcuit which will cause electrical shock Use extreme caution when using metal tools which can easily damage any electrical components or circuit boards they come into contact with Do not use mats designed to decrease electrostatic discharge as protection from electrical shock Instead use rubber mats that have been specifically designed as electrical insulators The power supply power cords must include a grounding plug and must be plugged into grounded electrical outlets Power input requires 110 240 VAC depending upon your power supply module Mainboard Battery This battery must be replaced only with the same or an equivalent type recommended by the manufacturer CR2032 Lithium 3V battery Dispose of used batteries according to the manufacturer s instructions WARNING There is a danger of explosion if the onboard battery is installed A upside down which will reverse its polarities Mainboard replaceable soldered in fuses Self resetting PTC Positive Temperature Coefficient fuses on the mainboard must be replaced by trained service technicians only The new fuse must be the same or equivalent as the one replaced Contact technical support for details and support 2 1 SC933 SC833 Air Shroud User s Guide 2 2 General Safety Precautions Follow these rules to ensure general safety e Keep the area around the server clean and free of clutter e Place the blade module cover and any system components that have been removed
14. the outside of the shipping carton and mailed prepaid or hand carried Shipping and handling charges will be applied for all orders that must be mailed when service is complete For faster service RMA authorizations may be requested online at http www supermicro com support rma Whenever possible repack the chassis in the original Supermicro carton using the original packaging material If these are no longer available be sure to pack the chassis securely using packaging material to surround the chassis so that it does not shift within the carton and become damaged during shipping This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alteration misuse abuse or improper maintenance of products During the warranty period contact your distributor first for any product problems 1 2 Chapter 1 Introduction 1 5 Contacting Supermicro Headquarters Address Tel Fax Email Web Site Europe Address Tel Fax Email Asia Pacific Address Tel Fax Web Site Technical Support Email Tel Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A 1 408 503 8000 1 408 503 8008 marketing supermicro com General Information support supermicro com Technical Support www supermicro com Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands 31 0 73 6400
Download Pdf Manuals
Related Search