Sun StorageTek 5800 System Site Preparation Guide
Contents
1. 2 Cabinet Specifications and Site Requirements Dimension and Weight 5 Environmental Requirements 6 Temperature Humidity and Altitude 6 Airflow and Heat Dissipation 7 Maximum Heat Output 7 Power Reguirements 8 Network Reguirements 8 A Configuration Worksheet 11 5 iv Undefined BookTitleFooter June 2008 Figures vi Undefined BookTitleFooter June 2008 Tables TABLE 2 1 TABLE 2 2 TABLE 2 3 TABLE 2 4 TABLE 2 5 TABLE 2 6 TABLE 2 7 TABLE A 1 Sun Rack STK5800 Cabinet Dimensions 5 Sun Rack STK5800 Cabinet and Component Weights 6 Cabinet Temperature Humidity and Altitude 6 5800 System Relative Humidity RH Noncondensing 7 Remaining Power Available in Rack After 5800 System is Installed 7 Rack AC Power Requirements 8 Power Cords Required for the 5800 System 8 5800 System Configuration Worksheet 12 vii viii Undefined BookTitleFooter June 2008 Preface This guide describes facilities and system requirements for installing the Sun StorageTek 5800 System Follow the guidelines as outlined in this document when planning your installation Note This guide describes what you must do to prepare your site for the installation of the 5800 system The actual installation must be performed by qualified Sun Service personnel Before You Read This Book Before you begin to install the 5800 system read the regulatory and safety requirements described in this book m Sun Stora2. C for every 3280 ft 1000 m above sea level TABLE 2 4 lists the acceptable humidity ranges in which the 5800 system is designed to operate TABLE 2 4 5800 System Relative Humidity RH Noncondensing Maximum Rate of Change Specification per Hour Operating range 20 to 80 Storage range 10 to 93 Transit range 5 to 95 Maximum dew point 79 F 26 C Maximum gradient 10 per hour Airflow and Heat Dissipation Rack airflow is from front to back Allow at least 30 inches 76 2 cm in front of the rack and at least 24 60 96 cm inches behind the rack for service clearance proper ventilation and heat dissipation Maximum Heat Output The maximum heat output for the 5800 system is as follows m Half cell 2420 watts 8257 BTU hr m Full cell 4420 watts 15082 BTU hr m Dual cell 8840 watts 30163 BTU hr TABLE 2 5 lists the remaining power available for additional equipment in a rack when a 5800 system is installed in the rack TABLE 2 5 Remaining Power Available in Rack After 5800 System is Installed Installed 5800 System Power Available for Additional Equipment in Rack Half cell 11660 watts Full cell 9660 watts Chapter 2 Cabinet Specifications and Site Requirements 7 Power Requirements The AC power sources must provide the correct voltage current and frequency specified on the component model and serial number label The cabinet can run within the limits shown in TABLE 2 6 TABLE 2 6 Ra
3. MTP server IP address 129 146 11 86 Authorized clients IP addresses AII External Logger IP address 10 7 224 10 DNS enable or disable disable Domain name sfbay sun com DNS search path sfbay sun com sun com Primary DNS server IP address 129 146 11 51 Secondary DNS server IP address 129 146 11 103 Alert email recipient address None To Cell ID 0 Note If this is a multi cell configuration you must supply the cell ID at installation You can use host names instead of IP addresses for these values if DNS is enabled 12 Sun StorageTek 5800 System Site Preparation Guide June 2008
4. SS amp o SUN microsystems Sun StorageTek 5800 System Site Preparation Guide Sun Microsystems Inc WWW SUN COM Part No 820 1635 11 June 2008 Revision A Submit comments about this document at http www sun com hwdocs feedback Copyright 2007 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 U S A All rights reserved Sun Microsystems Inc has intellectual property rights relating to EE is described in this document In particular and without limitation these intellectual property rights may include one or more of the U S patents listed at http www sun com patents and one or more additional patents or pending patent applications in the U S and in other countries This documentand the product to which it pertains are distributed under licenses restricting their use copying distribution and decompilation No part of the product or of this document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the s produtt may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and in other countries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo Java AnswerBook2 docs sun com Sun StorEdge Sun StorageTek and Solaris are tra
5. ck AC Power Requirements Parameter Requirements Nominal voltages 200 to 240 VAC Operating voltage 180 to 264 VAC Frequency range 50 to 60 Hz Single Phase Current 32A 2 x 16A maximum AC power plug NEMA L6 20P North American IEC 309 16A 3 Position International AC power receptacle NEMA L6 20R North American IEC 309 16A 3 Position International Power cords required 2 for half cell and full cell configurations 4 for dual cell configurations TABLE 2 7 Power Cords Required for the 5800 System Power Cord Type Part Number Domestic Sun MEG PN 595 6715 02 20A 250V International Sun MFG PN 595 6716 02 16A 200 250V Network Requirements Your network must include the following features to allow for successful installation and administration of the 5800 system 8 Sun StorageTek 5800 System Site Preparation Guide June 2008 If you want to administer the 5800 system using the command line interface CLI the system from which you want to access the CLI must be running a secure shell SSH client If you want to administer the 5800 system using the graphical user interface GUI you must have a Java enabled web browser on your network Refer to the Sun StorageTek 5800 System Release Notes for versions of Java that are supported You must reserve three IP addresses on your network per half cell or full cell for data administration and service access There must be at least one Network Time Protoc
6. demarks or registered trademarks of Sun Microsystems Inc in the U S and in other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S and in other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees viho implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements U S Government Rights Commercial use Government users are subject to the Sun Microsystems Inc standard license agreement and applicable provisions of the FAR and its supplements DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 2007 Sun Microsystems Inc 4150 Network Circle Santa Clara Californie 95054 Etats Unis Tous droits r serv s Sun Mic
7. e called class options Replace command line variables You must be superuser to do this with real names or values To delete a file type rm filename The settings on your browser might differ from these settings Preface xi xii Related Documentation The following table lists the documents for this product The online documentation is available at http docs sun com app docs prod stortek 5800 hic Title Sun StorageTe 5800 System Regulatory and Safety Compliance Manual Sun StorageTek 5800 System Administration Guide Sun StorageTek 5800 System Overview Sun StorageTek 5800 System Release Notes Sun StorageTek 5800 System Client API Reference Guide Sun StorageTek 5800 System SDK Developer s Guide Part Number 819 3809 xx 820 4118 xx 820 4119 xx 820 4120 xx 820 4796 xx 820 4797 xx Format HTML PDF HTML PDF HTML PDF HTML PDF PDF PDF Location Online Online Online Online Online Online Sun StorageTek 5800 System Site Preparation Guide June 2008 Documentation Support and Training Sun Function URL Documentation http www sun com documentation Support http www sun com support Training http www sun com training Third Party Web Sites Sun is not responsible for the availability of third party web sites mentioned in this document Sun does not endorse and is not responsible or liable for any content adve
8. eTek 5800 System Site Preparation Guide June 2008 CHAPTER 2 Cabinet Specifications and Site Requirements This chapter describes the physical environmental and electrical requirements for the Sun Rack 1000 38 STK5800 cabinet which is the cabinet used for the Sun StorageTek 5800 System The floor area at the installation site must provide enough stability to support the weight of the cabinet and installed trays sufficient space for installation and servicing of the cabinet and components and sufficient ventilation to provide a free flow of air to the cabinet To ensure safe and proper operation of the system and ease of maintenance make sure that all of these requirements are met before using the cabinet It contains the following sections m Dimension and Weight on page 5 m Environmental Reguirements on page 6 m Power Reguirements on page 8 m Network Reguirements on page 8 Dimension and Weight TABLE 2 1 provides the physical dimensions of the Sun Rack STK5800 cabinet TABLE 2 1 Sun Rack STK5800 Cabinet Dimensions Dimensions Height Width Depth American 74 in 23 5 in 35 4 in Metric 188 cm 59 7 cm 89 9 cm A fully loaded Sun Rack 1000 38 STK5800 cabinet has a maximum weight capacity of 1500 pounds 680 4 kilograms The total weight of your Sun Rack STK5800 cabinet depends on the number and type of components installed in the cabinet TABLE 2 2 displays the weights of each diffe
9. eliberately and make sure that the floor is free from foreign objects and cables that the cabinet could roll over A Caution To avoid injury wear protective footwear when moving a system Secure Installation Requirements To minimize personnel injury in the event of a seismic occurrence you must securely fasten the cabinet to a rigid structure extending from the floor to the ceiling or from the walls of the room in which the cabinet is located Install the cabinet on a level surface At each corner on the base of the cabinet are adjustable nonskid pads Extend these pads when the cabinet is installed to prevent the cabinet from rolling Do not use these pads to level the cabinet 2 Sun StorageTek 5800 System Site Preparation Guide June 2008 Placement of a Sun Product Allow enough room surrounding the cabinet for access to the cabinet and arrays for maintenance Caution Do not block or cover the openings of your Sun product Never place a Sun product near a radiator or heat register Failure to follow these guidelines can cause overheating and affect the reliability of your Sun product Air cools the system cabinets from front to back Air enters at the front circulates and is expelled at the back of the cabinet The front and back door clearances provide sufficient space for cooling See Chapter 2 for specific clearance specifications Site Wiring and Power Reguirements The AC power distribution boxes
10. es les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux tats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc L interface utilisateur graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconna t les efforts de pionniers de Xerox dans la recherche et le SC pement du concept des interfaces utilisateur visuelles ou graphiques pour l industrie informatique Sun d tient une license non exclusive de Xerox sur l interface utilisateur graphique Xerox cette licence couvrant galement les licenci s de Sun impl mentant les interfaces utilisateur graphiques OPEN LOOK et se conforment en outre aux licences crites de Sun LA DOCUMENTATION EST FOURNIE EN L TAT ET TOUTES AUTRES CONDITIONS DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES DANS LA LIMITE DE LA LOI APPLICABLE Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALIT MARCHANDE L APTITUDE UNE UTILISATION PARTICULI RE OU A L ABSENCE DE CONTREFA ON SC BA Adobe PostScript Contents Preface ix 1 Planning for the Installation 1 Customer Obligations 1 Safety Information 1 Handling Precautions 2 Secure Installation Requirements 2 Placement of a Sun Product 3 Site Wiring and Power Requirements 3
11. geTek 5800 System Regulatory and Safety Compliance Manual How This Book Is Organized Chapter 1 describes the requirements for preparing your site for installation of the 5800 system Chapter 2 describes the physical environmental and electrical requirements for the cabinet in which the 5800 system is installed Appendix provides worksheets to help you gather the information you need to complete the installation Using UNIX Commands This document might not contain information on basic UNIX commands and procedures such as shutting down the system booting the system and configuring devices Refer to the following for this information m Software documentation that you received with your system m Solaris Operating System documentation which is at http docs sun com x Sun StorageTek 5800 System Site Preparation Guide June 2008 Shell Prompts Shell Prompt C shell machine name C shell superuser machine name Bourne shell and Korn shell Bourne shell and Korn shell superuser Typographic Conventions Typeface Meaning Examples AaBbCc123 The names of commands files Edit your login file and directories on screen Use 1s a to list all files computer output You have mail AaBbCc123 What you type when contrasted su with on screen computer output password AaBbCc123 Book titles new words or terms Read Chapter 6 in the User s Guide words to be emphasized These ar
12. in the cabinet use common industrial wiring Consider the following information when preparing the cabinet installation site m AC power source The AC power source must provide the correct voltage current and freguency specified on the module model and serial number label m Earth ground Site wiring must include an earth ground connection to the AC power source m Circuit overloading Power circuits and associated circuit breakers must provide sufficient power and overload protection To prevent possible damage to the AC power distribution boxes and other components in the cabinet use an external independent power source that is isolated from large switching loads such as air conditioning motors elevator motors and factory loads m Module power distribution All units attached to the two power strips inside that cabinet must be autoranging between 180 and 264 VAC 47 63 Hz m Power interruptions The cabinet and modules will withstand the following applied voltage interruptions with or without an integrated uninterruptible power supply UPS Input transient OV for 1 cycle with no interruption Duration 70 percent of nominal for 0 5 seconds and OV for 5 seconds recoverable with user intervention m Power failures If a total power failure occurs when power is restored the nodes within the cabinet automatically perform a power on recovery Chapter 1 Planning for the Installation 3 4 Sun Storag
13. ol NTP server available on the network If you want to have system alerts emailed to an administrator you must have an email address available for this purpose and a Simple Mail Transfer Protocol SMTP server available on the network None of the hosts located on the same subnet as the 5800 system can use the following addresses which are reserved for use by the 5800 system a 10 123 0 1 n 10 123 0 2 n 10 123 45 1 n 10 123 45 100 through 10 123 45 116 n 10 123 45 200 through 10 123 45 220 Chapter 2 Cabinet Specifications and Site Requirements 9 10 Sun StorageTek 5800 System Site Preparation Guide June 2008 APPENDIX A Configuration Worksheet DO NOT ATTEMPT TO INSTALL THIS PRODUCT The 5800 system must be installed upgraded and expanded only by qualified Sun service personnel or a qualified Sun service partner To contact Sun service personnel g0 to http www sun com service contacting Use the worksheets in this appendix to help you collect the information you need to provide to the authorized Sun service personnel TABLE A 1 lists the information you need to collect TABLE A 1 5800 System Configuration Worksheet Factory Default our configuration Administrative IP address 10 7 227 101 Data IP address 10 7 227 102 Service node IP address 10 7 227 100 Subnet mask 255 255 252 0 Gateway IP address 10 7 227 254 NTP servers IP addresses 129 145 155 32 129 146 17 39 S
14. rent configuration Use these weights to estimate the total weight of your system based on the number of components installed in the cabinet Record the total weight in an easy to find place to reference when checking flooring load or elevator weight restrictions TABLE 2 2 Sun Rack STK5800 Cabinet and Component Weights Component Total Weight 8 node cell nodes switches and cables 705 lbs 319 8 kgs 16 node cell nodes switches and cables 990 Ibs 449 1 kgs Dual cell nodes switches and cables 1265 lbs 573 8 kgs Environmental Requirements This section describes the environmental conditions that are prerequisite to installing Sun Rack cabinets Temperature Humidity and Altitude TABLE 2 3 lists operating and nonoperating temperature relative humidity and altitude ranges for the STK5800 rack TABLE 2 3 Cabinet Temperature Humidity and Altitude Specification Operating Nonoperating Temperature 41 F to 95 F 45 4 F to 154 4 F 5 C to 35 C 43 C to 68 C Relative humidity RH 7 to 93 93 noncondensing at noncondensing 104 F 40 C for 5 days Altitude 0 to 10498 7 feet 0 to 0 to 40 026 2 feet 0 to 3 2 km at 104 F 40 C 12 2 km at 32 F 0 C for 4 hours 6 Sun StorageTek 5800 System Site Preparation Guide June 2008 If you plan to operate a system at an altitude between 3280 ft to 10 000 ft 1000 m to 3048 m above sea level lower the environmental temperature 3 3 F 1 7
15. rosystems Inc poss de les droits de propri t intellectuels relatifs la technologie d crite dans ce document En particulier et sans limitation ces droits de propri t intellectuels peuvent inclure un ou plusieurs des brevets am ricains list s sur le site 7 http www sun com patents un ou les plusieurs brevets suppl mentaires ainsi que les demandes de brevet en attente aux les Etats Unis et dans d autres pays Ce document et le produit auquel il se rapporte sont prot g s par un copyright et distribu s sous licences celles ci en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne peut tre reproduite sous aucune forme par quelque moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bailleurs de licence s il y en a Tout logiciel tiers sa technologie relative aux polices de caract res comprise est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit peuvent d river des syst mes Berkeley BSD licenci s par l Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun Java AnswerBook2 docs sun com Sun StorEdge Sun StorageTek et Solaris sont des marques de fabrique ou des marques d pos es de Sun Microsystems Inc aux tats Unis et dans d autres pays Tout
16. rtising products or other materials that are available on or through such sites or resources Sun will not be responsible or liable for any actual or alleged damage or loss caused by or in connection with the use of or reliance on any such content goods or services that are available on or through such sites or resources Contacting Sun Technical Support If you have technical questions about this product that are not answered in this document go to http www sun com service contacting Sun Welcomes Your Comments Sun is interested in improving its documentation and welcomes your comments and suggestions You can submit your comments by going to http www sun com hwdocs feedback Preface xiii Please include the title and part number of your document with your feedback Sun StorageTek 5800 System Site Preparation Guide part number 820 1635 11 xiv Sun StorageTek 5800 System Site Preparation Guide June 2008 CHAPTER 1 Planning for the Installation This chapter describes the requirements for preparing the customer site for installation of the 5800 system This chapter contains the following sections m Customer Obligations on page 1 m Safety Information on page 1 m Site Wiring and Power Reguirements on page 3 Customer Obligations The customer is obliged to inform Sun Microsystems Inc of any and all ordinances and regulations that might affect the installation The customer is re
17. sponsible for meeting all government codes and regulations concerning facilities The customer is also reguired to do the following m Comply with all local national and international codes covered in this specification The subjects covered include fire and safety building and electrical codes m Document and inform Sun Microsystems Inc of any deviations from this specification Safety Information Install the 5800 system in accordance with the local safety codes and regulations at the facility site Make sure that you read the safety precautions in the Sun StorageTek 5800 System Regulatory and Safety Compliance Manual The following sections contain additional safety information for the local facility m Handling Precautions on page 2 m Secure Installation Reguirements on page 2 m Placement of a Sun Product on page 3 Note Do not make mechanical or electrical modifications to the equipment Sun Microsystems Inc is not responsible for regulatory compliance of a modified Sun product Handling Precautions Caution A fully populated cabinet can weigh in excess of 1280 pounds 580 6 kilograms Ensure that all surfaces this system will move over can withstand this load The cabinet is equipped with wheels so you can move it Use enough personnel when moving the cabinet especially on sloped loading docks and ramps to gain access to a raised computer room floor Move the cabinet slowly and d
Download Pdf Manuals
Related Search