Sun Blade 100 Motherboard Update and Sun PGX64 Patch
Contents
1. A Type the root password and press the Enter key The system displays the prompt indicating that you are superuser 5 Insert the PGX64 CD into the CD ROM drive 6 At the prompt type mkdir cdrom 7 Type cd 8 To mount the CD ROM type mount F hsfs dev dsk c0t1d0s0 cdrom 9 To access the directory on the CD ROM which contains the patches type cd cdrom Solaris_8 Patches 10 Type 1s to determine the latest patch revision contained on the CD ROM 1s 108606 09 Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures 5 11 Type the patchadd command using the exact patch number in the Patches directory patchadd 108606 09 The system shows the packages being added and returns you to the command prompt 12 Power off the system The patch procedure is complete 6 Patch Procedure 2 Installing Earlier Solaris 8 Operating Environments and the Sun PGX64 Patch on Sun Blade 100 Workstations with Solaris 8 7 01 or Later Use this procedure if you have a workstation that has a motherboard part number 375 3106 with Solaris 8 7 01 or later installed and you want to install Solaris 8 10 00 1 01 or 4 01 Required Tools m Solaris 8 10 00 1 01 or 4 01 media kit m Sun PGX64 CD Recommended TTY Connection Procedure If possible you should use a TTY connection to install the Solaris 8 operating environment and the PGX64 patch If you don2. t use the TTY procedure you must complete an immediate system shutdown after installing Solaris 8 10 00 1 01 or 4 01 Therefore you may have to run fsck to clean the file system The immediate shutdown is necessary because the PGX 64 patch is added after installing the Solaris 8 operating environment and the system monitor is blank until the PGX64 patch is installed Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures July 2002 If you use the TTY connection to install the Solaris 8 operating environment and the PGX64 patch you can complete an orderly shutdown procedure and avoid the blank monitor problem and any file system repairs Power on the Sun Blade 100 workstation Note If you will not use a TTY connection begin your procedure with Installing the Solaris 8 Operating Environment on page 8 At the ok prompt type printenv to check the OpenBoot PROM parameters for the input and output devices ok printenv Set the input device to TTYA ok setenv input device TTYA Set the output device to TTYA ok setenv output device TTYA Reset the OpenBoot PROM parameters ok reset all resetting The TTY procedures are complete for the Sun Blade 100 system Now set the remote console to communicate with the Sun Blade 100 system Connect the remote console device to the TTYA serial port Using the remote console access the ok prompt and boot the Sun Blade 100 system in singl
3. S amp SUN microsystems Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures For Sun Blade 100 Systems with the Solaris 8 10 00 1 01 or 4 01 Operating Environments Sun Microsystems Inc 4150 Network Circle Santa Clara CA 95054 U S A 650 960 1300 Part No 816 7660 10 July 2002 Revision A Send comments about this document to docfeedback sun com Copyright 2002 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 U S A All rights reserved Sun Microsystems Inc has intellectual property rights relating to technology embodied in the product that is described in this document In particular and without limitation these intellectual property rights may include one or more of the U S patents listed at ttp www sun com patents and one or more additional patents or pending patent applications in the U S and in other countries This document and the product to which it pertains are distributed under licenses restricting their use copying distribution and decompilation No part of the product or of this document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the produet may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and in other co
4. TY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 2002 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 Etats Unis Tous droits r serv s Sun Microsystems Inc a les droits de propri t intellectuels relatants a la technologie incorpor e dans le produit qui est d crit dans ce document En particulier et sans la limitation ces droits de propri t intellectuels peuvent inclure un ou plus des brevets am ricains num r s a http www sun com patents et un ou les brevets plus suppl mentaires ou les applications de brevet en attente dans les Etats Unis et dans les autres pays Ce produit ou document est prot g par un copyright et distribu avec des licences qui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne peut tre reproduite sous aucune forme parquelque moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bailleurs de licence s il y ena Le logiciel d tenu par des tiers et quicomprend la technologie relative aux polices de caract res est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par l Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d aut
5. ULIERE OU A L ABSENCE DE CONTREFA ON LD Ca Adobe PostScript Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures Procedure Overview and Patch Description TM Installing a new motherboard into the Sun Blade 100 may cause the system monitor to go blank if the system is using certain Solaris releases A patch resolves the problem To order the patch kit contact your Sun service representative This procedure is only required for Sun Blade 100 workstations with motherboard part number 375 3106 and one of these Solaris releases m Solaris 8 10 00 m Solaris 8 1 01 m Solaris 8 4 01 These procedures should only be performed by experienced system administrators or authorized Sun service representatives Note There are two main procedures in this document Each procedure is distinctly different depending on the system configuration Be sure to follow the correct procedure for your system m Patch Procedure 1 is necessary if your Sun Blade 100 workstation is currently operating with Solaris 8 10 00 1 01 or 4 01 and requires a new motherboard part number 375 3106 m Patch Procedure 2 is necessary if you have a workstation that already has a motherboard part number 375 3106 with Solaris 8 7 01 or later installed and you want to install an earlier version of Solaris 8 10 00 1 01 or 4 01 Identifying the Motherboard All motherboards that require the patch will have part number 375 3106 on a labe
6. d Replacement Procedure 1 Follow the procedures in the Sun Blade 100 Service Manual to remove the CPU and DIMMs from the original motherboard 2 Install the CPU and DIMMs onto the new motherboard 3 Install the new motherboard into the Sun Blade 100 workstation 4 Connect all the cables to the system Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures 3 Patch Procedure 1 Installing the Sun PGX64 Patch on Sun Blade 100 Workstations with Solaris 8 10 00 1 01 or 4 01 Required Tools m Sun PGX64 CD Before You Begin Only use this procedure if your Sun Blade 100 workstation is currently operating with Solaris 8 10 00 1 01 or 4 01 Adding the PGX64 Patch 1 Power on the system 2 As soon as you see the Sun Blade 100 system banner press Stop A Sun Blade 100 UltraSPARC IIe Keyboard Present Copyright 1998 2002 Sun Microsystems Inc All rights reserved OpenBoot 4 6 128 MB memory installed Serial 516xxxxxx Ethernet address 0 x xx xx xx xx Host ID 8x1x3xxx The system stops loading the Solaris operating environment and displays the ok prompt 3 Boot the system in single user mode by typing ok boot s 4 Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures July 2002 The system boots and asks for your root password Resetting INIT SINGLE USER MODE Type control d to proceed with normal startup or give root password for system maintenance
7. e user mode ok boot s Both systems are now ready for the Solaris 8 installation and the PGX64 patch installation Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures 7 Installing the Solaris 8 Operating Environment 1 Install the Solaris 8 operating environment by following the directions provided in your Solaris media kit Note Following the Solaris installation the workstation monitor is blank If you are not using a TTY connection an immediate shutdown sequence is required before you can add the PGX64 patch If you are using a TTY connection an orderly shutdown is possible 2 If you are using a TTY connection halt the Sun Blade 100 system by typing sync and halt at the remote console sync halt Skip Step 3 and proceed with PGX64 patch installation 3 If you are not using a TTY connection a Press and hold the power button for four seconds to power off the Sun Blade 100 system Wait at least five seconds before powering on the system b Power on the Sun Blade 100 system again by pressing the power button Note You may need to run the fsck command to clean the file system after the power off and power on sequence Adding the Sun PGX64 Patch 1 If you have not already powered on the Sun Blade 100 workstation power on the workstation now 8 Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures July 2002 As soon as you see the Sun Blade 100 syst
8. em banner press Stop A Sun Blade 100 UltraSPARC IIe Keyboard Present Copyright 1998 2002 Sun Microsystems Inc All rights reserved OpenBoot 4 6 128 MB memory installed Serial 516xxxxxx Ethernet address 0 x xx xx xx xx Host ID 8x1x3xxx The system stops loading the Solaris operating environment and stops at the ok prompt Boot the Sun Blade 100 system in single user mode by typing 9 beoe s The system boots and asks for your root password Resetting INIT SINGLE USER MODE Type control d to proceed with normal startup or give root password for system maintenance Enter the root password and press the Enter key The system displays the prompt indicating that you are superuser Insert the PGX64 CD into the CD ROM drive At the prompt type mkdir cdrom Type cd To mount the CD ROM type mount F hsfs dev dsk c0t1d0s0 cdrom Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures 9 9 To access the directory on the CD ROM which contains the patches type cd cdrom Solaris 8 Patches 10 Type 1s to determine the latest patch revision contained on the CD ROM ls 108606 09 11 Type the patchadd command patchadd 108606 09 The system shows the packages being added and returns you to the command prompt 12 If you are using a TTY connection redirect the system to the OK prompt by ty
9. l or silk screened onto the board See FIGURE 1 5 mM o O aS 5 a D a I 5 DODUUDUDOUUOUUI COCODDDOOOOUUI OANA gt ONTAN D fa i 7 Couto TUUTTI o NOOU0000000000 3 LODO N00 J22 Battery J20 J30 O lo A ep 3 Q S g lt E g a re Z at o 3753 1060xxxxxx o JP2 CO Part Number FIGURE 1 The Motherboard Part Number Label or Silkscreen is Near the Edge Connector 2 Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures July 2002 Removing and Replacing the Motherboard CPU and DIMMs Required Tools and Documentation m A 2 Phillips screwdriver a Sun Blade 100 Service Manual 806 3416 Follow the procedures in the Sun Blade 100 Service Manual Chapter 8 Removing and Replacing the Motherboard and Related Components The service manual was provided on a CD ROM that shipped with your workstation The service manual is online at http www sun com documentation Click the following links Additional Hardware Documentation gt Desktop amp Workstation gt Sun Blade Workstations Then click on the link for the Sun Blade 100 Motherboar
10. ping sync halt If you are using a TTY connection you should reset the Sun Blade 100 OpenBoot PROM input device and output device parameters to keyboard and screen 13 Set the Sun Blade 100 input device to keyboard ok setenv input device keyboard 14 Set the Sun Blade 100 output device to screen ok setenv output device screen 15 Reset the Sun Blade 100 OpenBoot PROM parameters ok reset all resetting The Sun Blade 100 workstation reboots 10 Sun Blade 100 Motherboard Update and Sun PGX64 Patch Procedures July 2002
11. res pays et licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun Sun Blade AnswerBook2 docs sun com et Solaris sont des marques de fabrique ou des marques d pos es de Sun Microsystems Inc aux Etats Unis et dans d autres pays Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits protant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc L interface d utilisation graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconna t les efforts de pionniers de Xerox pour la recherche et le d veloppment du concept des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique Sun d tient une license non exclusive do Xerox sur l interface d utilisation graphique Xerox cette licence couvrant galement les licenci es de Sun qui mettent en place l interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences crites de Sun LA DOCUMENTATION EST FOURNIE EN L TAT ET TOUTES AUTRES CONDITIONS DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE A L APTITUDE A UNE UTILISATION PARTIC
12. untries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo Sun Blade AnswerBook2 docs sun com and Solaris are trademarks or registered trademarks of Sun Microsystems Inc in the U S and in other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S and in other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees who implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements Use duplication or disclosure by the U S Government is subject to restrictions set forth in the Sun Microsystems Inc license agreements and as provided in DFARS 227 7202 1 a and 227 7202 3 a 1995 DFARS 252 227 7013 c 1 ii Oct 1998 FAR 12 212 a 1995 FAR 52 227 19 or FAR 52 227 14 ALT IMI as applicable DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILI
Download Pdf Manuals
Related Search