Home

Netra ft 1800 Interim Update Instructrions

1. All operations must be performed at the OBP ok prompt or as root Netra ft 1800 release software occupies approximately 540 Mbytes of disk space 6 Netra ft 1800 Interim Update Instructions September 1999 Patch verified i Verifying the Prerequisites Before You Start If any of the following verifications fails consult Sun Enterprise Services General The system should be free from faults that is no red LEDs showing and running in sync see To Confirm the System is Running in Sync on page 11 To Verify Mandatory Patches Type showrev p grep 107369 The output should include Patch 107369 17 Obsoletes 106616 01 Requires Incompatibles Packages SUNWcsu SUNWftcar SUNWcmscu SUNWcmsr SUNWcmsu SUNWcmsdf SUNWftm SUNWftmuu SUNWftutr SUNWftutu SUNWpnet SUNWspltr SUNWspltu Patch 107369 16 Obsoletes 106616 01 Requires Incompatibles Packages SUNWftcar SUNWcmscu SUNWcmsr SUNWcmsu SUNWcmsdf SUNWftm SUNWftmuu SUNWftutr SUNWftutu SUNWpnet SUNWspltr SUNWspltu or Patch 107369 17 Obsoletes 106616 01 Requires Incompatibles Packages SUNWcsu SUNWftcar SUNWcmscu SUNWcmsr SUNWcmsu SUNWcmsdf SUNWftm SUNWftmuu SUNWftutr SUNWftutu SUNWpnet SUNWspltr SUNWspltu 8 or Patch 107369 16 Obsoletes 106616 01 Requires Incompatibles Packages SUNWftcar SUNWcmscu SUNWcmsr SUNWcmsu SUNWcmsdf SUNWftm SUNWftmuu SUNWftutr SUNWftutu SUNW
2. CMS Control of the ICN Subsystem CMS control of the ICN subsystem is implemented via four new cmsdefs Two are simple device cmsdefs u4ftmbox and icnio that are visible in cmsconfig but have no user changeable attributes However they can provide information that may be useful in diagnosing problems The other two icn and icn_system constitute the user interface they are described in detail below There are two u4ftmbox objects four icnio objects four icn objects and one icn_system object icn_system This is the master CMS object for the icn subsystem Its only visible user operations are enable and disable Its task is to provide overall control of the subsystem icn_system 0 can only be enabled if the system is split when the system is combined it remains in the disabled state unless an explicit enable is requested in which case it will go to the enable_failed state setting the info field to System is not split Under normal operation the act of enabling and disabling icn_system 0 is automatically undertaken by u4ftsplitd and thus no user intervention should be required Enabling icn_system 0 automatically brings the u4ftmbox objects online and then enables the individual icn objects in that order Disabling icn_system 0 disables the icn objects and takes the u4ftmbox objects offline again in that order If the u4 ftmbox objects fail to come online icn_system goes enable_failedand does not proceed to perform any ac
3. Enter the item number for A CPU then select the Action item Press 1 to enable A CPU Wait for a few seconds then press Return to redisplay the menu Repeat until the display shows that A CPU is enabled then press q to return to the cmsconfig menu Wait for the system to come back into sync This may take a few minutes To verify follow the procedure To Confirm the System is Running in Sync on page 11 Enter the item number for B CPU then select the Action item Press 0 to disable B CPU Wait for a few seconds then press Return to redisplay the menu Repeat until the display shows that B CPU is disabled then press q twice to return to the prompt Invoke the update program cd usr platform SUNW Ultra 4FT lib netra_ft_1800 flash update 10 You will be asked if you wish to upgrade the PROMs Answer y and then yes to upgrade A list of NVRAM variables will be displayed for you to note and reset later if different from the default values Note these for safety although it should not be necessary to use them You will be asked if you wish to continue Answer yes to continue The upgrade will proceed and the success or failure of the upgrade will be reported If the update fails note any error messages and contact your Sun Enterprise Services You will be asked Do you wish to halt the system now Answer no 17 18 39 cmsconfig started 40 41 B CPU 42 re enabled
4. Field Values description Serial multiplexer porto NULL A CAF_console portl NULL A CAF_modem port2 NULL B CAF_console port3 NULL B CAF_modem redundancy The redundancy level of the system mode_of_use The file system device used to access the subsystem ports_in_use List of ports in use 31 a Table 9 3 Console Subsystem States on page 9 6 Add an extra state as follows State Means not_known The subsystem cannot determine its level of redundancy this is an error state m Delete the paragraph following Table 9 3 on page 9 6 Reference Manual Manpages The following changes should be made m ttymuxadm 1M AVAILABILITY should be SUNWtt ymx On line 166 change B CAF to B CAF m ttymux 7d AVAILABILITY should be SUNWttymx 32 Solaris Y2K Patch Compatibility The following Y2K patches currently available on SunSolve have been tested with this patch but are not included as part of the patch Patch Software Description 105210 22 SunOS 5 6 libc and watchmalloc 105800 05 SunOS 5 6 usr bin admintool 106193 03 SunOS 5 6 sysid unzip 106828 01 SunOS 5 6 usr bin date 107492 01 SunOS 5 6 runacct cannot update var adm acct sum log 105621 17 SunOS 5 6 libbsm and cron 105464 02 OpenWindows 3 6 Multiple xterm fixes 105566 07 CDE 1 2 Calendar manager 1 All patches tested at time of document delivery Netra ft 1800 Interim Update Instructions September 1999
5. atch 107926 m Ifa line including the patch number 107926 is displayed circle Y in the box otherwise circle N 24 Netra ft 1800 Interim Update Instructions September 1999 NVRAM variables noted B CPU upgrade completed Keep system up cmsconfig started B o 6 10 11 12 13 14 Invoke the update program m If you entered 23 in Step 2 on page 9 enter the following at the command line cd usr platform SUNW Ultra 4FT 1lib netra_ft_1800 flash update 09 m If you entered 21 in Step 2 on page 9 enter the following at the command line cd usr platform SUNW Ultra 4FT lib netra_ft_1800 flash update 07 You will be asked if you wish to upgrade Answer y and then yes to upgrade A list of NVRAM variables will be displayed for you to note and reset later if different from the default values Note these for safety although it should not be necessary to use them You will be asked if you wish to continue Answer yes to continue The upgrade will proceed and the success or failure of the upgrade will be reported If the update fails note any error messages and contact Sun Enterprise Services You will be asked Do you wish to halt the system now Answer no Start cmsconfig cd usr platform SUNW Ultra 4FT SUNWcms sbin cmsconfig Enter the item number for A CPU then select the Action
6. System in sync B 43 44 Start cmsconfig cd usr platform SUNW Ultra 4FT SUNWcms sbin cmsconfig Enter the item number for B CPU then select the Action item Press 1 to enable B CPU Wait for a few seconds then press Return to redisplay the menu Repeat until the display shows that B CPU is enabled then press q twice to return to the main menu Wait for the system to come back into sync This may take a few minutes To verify follow the procedure To Confirm the System is Running in Sync on page 11 Type eeprom auto boot true Netra ft 1800 Interim Update Instructions September 1999 Go to OBP prompt Enable the OSdog Go to OBP prompt Enable the OSdog E a J 45 46 47 48 49 To Enable or Disable the OSdog The OSdog functionality is enabled or disabled at boot time based on values stored in the motherboard EEPROM These can only be modified by an OBP command If you require the OSdog to be enabled proceed to Step 45 If you do not require the OSdog proceed to Step 48 To Enable the OSdog Type init 0 At the ok prompt type ok setenv auto boot false ok reset all ok 4f set conf osdog ok setenv auto boot true The OSdog is now permanently enabled Proceed to Step 50 To Disable the OSdog Type init 0 At the ok prompt type ok setenv auto boot false ok reset all ok 0 set conf osdog ok seten
7. otherwise proceed to Step 36 Osdog patch 35 Re install the OSdog patch i Il nets ee m If patch 107926 04 still resides in the var tmp directory type cd var tmp 107926 04 installpatch m If patch 107926 04 no longer resides in the var tmp directory download it from SunSolve at http sunsolve sun comand install it according to the instructions provided with the patch v To Re install the QFE Patch Perform this step only if the QFE patch was backed out in Step 31 on page 27 otherwise proceed to Step 37 QFE patch Eo 36 Re install the QFE patch re installed m If the patch still resides in the var tmp directory enter cd var tmp 107778 04 installpatch m If the patch no longer resides in the var tmp directory re install the patch as described in the Netra ft 1800 Software Release Notes part no 805 4527 13 37 Finally reboot the system init 6 29 This page is intentionally blank 30 Netra ft 1800 Interim Update Instructions September 1999 Functionality Addendum This Addendum contains details of documentation changes and functional additions since the last update Documentation Changes User s Guide The following changes should be made to the Netra ft 1800 User s Guide m Section 9 2 1 Console Subsystem on page 9 5 All references to sm should be replaced with ft_serial a Table 9 2 Console Subsystem Fields on page 9 5
8. item Press 1 to enable A CPU 25 15 A CPU re enabled System in sync a 16 17 18 B CPU disabled PROM Update the a 20 21 22 23 A CPU upgrade 24 completed 19 Wait for a few seconds then press Return to redisplay the menu Repeat until the display shows that A CPU is enabled then press q to return to the cmsconfig menu Wait for the system to come back into sync This may take a few minutes To verify follow the procedure To Confirm the System is Running in Sync on page 11 Enter the item number for B CPU then select the Action item Press 0 to disable B CPU Wait for a few seconds then press Return to redisplay the menu Repeat until the display shows that B CPU is disabled then press q twice to return to the prompt Invoke the update program a If you entered 23 in Step 2 on page 9 enter the following at the command line cd usr platform SUNW Ultra 4FT lib netra_ft_1800 flash update 09 m If you entered 21 in Step 2 on page 9 enter the following at the command line cd usr platform SUNW Ultra 4FT lib netra_ft_1800 flash update 07 You will be asked if you wish to upgrade Answer y and then yes to upgrade A list of NVRAM variables will be displayed for you to note and reset later if different from the default values Note these for safety although it should not be necessary to use them You will be asked if
9. v 1 To Install the Patches Verify that all prerequisites have been met Refer to Verifying the Prerequisites Before You Start on page 6 through page 9 If step 1 is not satisfied contact Sun Enterprise Services to assist you in achieving the correct level of installation then repeat step 1 If you installed the Sun QFE P patch 107778 as part of Step 2 or in a previous installation you must backout the patch before proceeding Type cd var sadm patch 107778 04 backoutpatch 107778 04 Download patches 108181 01 and 108145 10 or the latest versions from the web site at SunSolve http sunsolve sun con Copy them into the subdirectory var tmp Extract the files cd var tmp zcat 108181 01 tar Z zcat 108145 10 tar Z tar xvf tar xvf Read the caution at the top of page 11 then install the Kernel Update patch cd 108181 01 installpatch cd usr platform SUNW Ultra 4FT lib 105181 14 installpatch When prompted type yes to confirm the installation When installation of the patch is complete do not reboot 12 Netra ft 1800 Interim Update Instructions September 1999 7 Install the Netra ft 1800 upgrade patch Netra ft 1800 patch installed cd var tmp 108145 10 installpatch When prompted type yes to confirm the installation Note The patch delivers an updated version of the Configuration Management Sy
10. 1800 Interim Update Instructions September 1999 v To Verify PROM Firmware Levels PROM upgrade 56 For each CPUset type verified cd usr platform SUNW Ultra 4FT SUNWcms sbin cmsfruinfo l x CPU i s EE CPU PROM PARTNO EE CPU PROM DASH where x is A for A CPU or B for B CPU For both CPUsets the output should be 2587354 10 Both sides should be at the same revision level that is both 10 57 Type prtconf V The output should be OBP 3 7 24 0 1999 06 24 14 24 The 24 indicates that the PROM level is 24 Backing Out Strategy The stages involved are as follows 1 Backout the PROM 2 Backout the QFE patch if installed 3 Backout the OSdog patch if installed 4 Backout the interim update patch D 5 Backout the kernel update 6 Re install the OSdog patch if required 7 Re install the QFE patch if required 8 Reboot the system v To Backout the PROM cmsconfig 1 Start cmsconfig started cd usr platform SUNW Ultra 4FT SUNWcems sbin cmsconfig 2 Enter the item number for A CPU then select the Action item 3 Press 0 to disable A CPU A CPU 4 Wait for a few seconds then press Return to redisplay the menu disabled Repeat until the display shows that A CPU is disabled then press q twice to exit from cmsconfig OSdog 5 Determine which patch you are reverting to by typing the installed Y N following at the command line patchadd p grep
11. 181 14 which is delivered as part of patch 108181 01 You can download both of these patches from SunSolve at http sunsolve sun com In order to upgrade the system successfully you must already have installed m The base system from the Netra ft 1800 Installation CD part no 704 6491 11 a The mandatory patches from the Netra ft 1800 Patch CD part no 704 6823 12 These patches are a 107369 16 or 17 Netra ft 1800 software patch a 106929 01 SunOs 5 6 usr uadmin patch and are also available from SunSolve Caution The mandatory patches listed above must be installed before you proceed with the upgrade In addition you may have also installed m 108065 03 Netra ft 1800 Bridge patch m 107926 04 Netra ft 1800 OSdog patch If you installed the Sun QFE P patch 107778 as part of the existing installation it will be necessary to back out the patch see Step 3 on page 12 and then re install it see Step 8 on page 13 following the instructions in this document Instructions for installing the base system and mandatory patches are contained in the Netra ft 1800 Software Release Notes part no 805 4527 13 Caution You must follow precisely the installation instructions in this document The installation procedure for the patches involves special instructions Installing the patches incorrectly can leave your system unusable requiring a complete re installation of all software which can take up to four hours
12. 33 The flow chart on page 4 and continued on page 5 shows the procedure for installing the upgrade START Pre Set system a to req d level PREREQUISITES QFE patch installed Backout patch 107778 04 Install patch Install patch Install Patch D 108181 01 108181 01 Install patch Install patch 105181 14 105181 14 RE Install patch Install patch 108145 10 108145 10 Re install patch 107778 04 INSTALL PATCH D FPGA Y at 08 N Install FPGAs UPGRADE FPGAs REBOOT v Continued on next page 4 Netra ft 1800 Interim Update Instructions September 1999 from previous page Update PROMs UPGRADE PROMs OSdog required OSDOG Enable OSdog Disable OSdog Vv Power OFF Cycle POWER RECYCLE CRN A Verify patch D installation Verify FPGA installation ean Verify PROM installation VERIFICATION Netra ft 1800 Interim Update Instructions 5 AN Prerequisites Caution Read all the instructions before attempting the installation procedure to ensure that you understand them and have everything required to hand The Netra ft 1800 upgrade software is supplied as a patch 108145 10 or whichever is the latest version In addition to this patch you will require the Kernel Update patch 105
13. ARC trademarks are based upon an architecture developed by Sun Microsystems Inc The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees who implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements RESTRICTED RIGHTS Use duplication or disclosure by the U S Government is subject to restrictions of FAR 52 227 14 g 2 6 87 and FAR 52 227 19 6 87 or DFAR 252 227 7015 b 6 95 and DFAR 227 7202 3 a DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 1999 Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 Etats Unis Tous droits r serv s Ce produit ou document est prot g par un copyright et distribu avec des licences qui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne peut tre reproduite sous aucune forme par quel
14. Netra ft 1800 Interim Update Instructions Important Read Before Installation Qe SUN microsystems THE NETWORK IS THE COMPUTER Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 4900 USA 650 960 1300 Fax 650 969 9131 Part No 806 3437 10 September 1999 Revision B Send comments about this document to docfeedback sun com Copyright 1999 Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 USA All rights reserved This product or document is protected by copyright and distributed under licenses restricting its use copying distribution and decompilation No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the product may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and other countries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo AnswerBook Java the Java Coffee Cup Netra Netra ft and Solaris are trademarks registered trademarks or service marks of Sun Microsystems Inc in the U S and other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S and other countries Products bearing SP
15. Sun Enterprise Services Y To Verify the Patch Installation 53 Type showrev p grep 105181 14 The output should be Patch 105181 14 Obsoletes 105214 01 105636 01 105776 01 106031 02 106308 01 Requires Incompatibles Packages SUNWkvm SUNWcsr SUNWcar SUNWhea Patch 108145 10 Obsoletes 108065 03 107926 03 107369 16 Requires 105181 14 Incompatibles Packages SUNWcsu SUNWftcar SUNWftcau SUNWcmscu SUNWcmsr SUNWcmsu SUNWcmsdf SUNWcrash SUNWftm SUNWftmur SUNWftmuu SUNWftutr SUNWftutu SUNWlogr SUNWlogu SUNWpnet SUNWspltr SUNWspltu SUNWttymx Patch installation 54 Type verified ia showrev p grep 108145 The output should be Patch 108145 10 Obsoletes 108065 03 107926 03 107369 16 Requires 105181 14 Incompatibles Packages SUNWcsu SUNWftcar SUNWftcau SUNWcmscu SUNWcmsr SUNWcmsu SUNWcmsdf SUNWcrash SUNWftm SUNWftmur SUNWftmuu SUNWftutr SUNWftutu SUNWlogr SUNWlogu SUNWpnet SUNWspltr SUNWspltu SUNWtty 21 v To Verify FPGA Firmware Levels FPGA upgrade 55 For each motherboard type verified cd usr platform SUNW Ultra 4FT SUNWcms sbin cmsfruinfo l x MBD i s EE MBD BRIDGE FWARE PARTNO EE MBD BRIDGE FWARE _DASH where x is for motherboard A or B for motherboard B For both motherboards the output should be 2587134 08 Both sides should be at the same revision level that is both 08 22 Netra ft
16. U PROM revision 07 or version 23 for CPU PROM revision 09 This page is intentionally blank 10 Netra ft 1800 Interim Update Instructions September 1999 Patch Installation This installation procedure including the two required reboots will take approximately ninety minutes Note There are special instructions for backing out this patch Refer to Backing Out Strategy on page 24 Caution Do not reboot at any stage of the installation process unless specifically requested to do so in this document In particular rebooting after step 6 and before step 7 has completed will render the system unusable To Confirm the System is Running in Sync Steps 10 29 and 43 require you to verify that the system is running in sync or Wait for the system to come back into sync To determine if the CPUsets are running in sync perform either of the following m Examine the amber LEDs labeled Diag on the front panel of each CPUset If they are running in sync the LEDs will flash exactly at the same time m Enter the following command cd usr platform SUNW Ultra 4FT SUNWcms 1ib u4ftvmctl c If the CPUsets are running in sync the following message is displayed CPUsets running combined 11 Prerequisites verified Base software and patches installed Back out QFE P patch Patches downloaded Patch files extracted Kernel Update patch installed EE Serre o
17. atching icn configuration file CMS object icn 0 reads etc config icn0 and so on for the other instances contains a hostname then the icn object is automatically enabled and the interface plumbed and brought online If the configuration file does not contain a hostname then the icn instance automatically goes to the disabled state Once enabled a disable action unplumbs the network interface takes the necessary devices offline and goes to the disabled state A subsequent enable will bring the interface back online The hostname attached to an interface cannot be changed while the interface is marked as up Memory size cannot be changed if the interface is up or down Individual icn interfaces can be reset by disabling and then enabling the appropriate icn object Netra ft 1800 Interim Update Instructions September 1999
18. em is running in sync by following the procedure To Confirm the System is Running in Sync on page 11 14 Netra ft 1800 Interim Update Instructions September 1999 10 FPGAs upgraded on one side Keep system up 11 FPGAs upgraded 12 on other side System rebooted a 13 System in sync a 14 WARNING This firmware update can only be performed on 1 The side which is executing this update utility 2 The other side if its cpuset is powered off 3 Either side if running in sync Please enter the side of the system that you want to update A or B Type cd usr platform SUNW Ultra 4FT 1lib fwupdate fpga 258 7134 08 You will be prompted Type A to upgrade motherboard A or B to upgrade motherboard B then type yes to confirm When asked if you want to halt the system answer no The power cycle for the FPGA upgrades is performed later at Step 50 on page 20 Repeat Step 10 and Step 11 for the other motherboard Reboot the machine To Upgrade the PROMs You must disable each CPUset in turn in order to upgrade the remaining CPUset PROM Wait for the system to come back into sync following Step 13 This may take a few minutes To verify follow the procedure To Confirm the System is Running in Sync on page 11 15 16 15 cmsconfig started 16 17 A CPU disabled 18 Update the 19 PROM 20 NVRAM variables 21 noted 22 B CPU upgrade 23 comp
19. leted Keep system up a 24 cmsconfig 25 started Start cmsconfig cd usr platform SUNW Ultra 4FT SUNWcms sbin cmsconfig Enter the item number for A CPU then select the Action item Press 0 to disable A CPU Wait for a few seconds then press Return to redisplay the menu Repeat until the display shows that A CPU is disabled then press q twice to exit from cmsconfig Invoke the update program cd usr platform SUNW Ultra 4FT 1lib netra_ft_1800 flash update 10 You will be asked if you wish to upgrade the PROMs Answer y and then yes to upgrade A list of NVRAM variables will be displayed for you to note and reset later if different from the default values Note these for safety although it should not be necessary to use them You will be asked if you wish to continue Answer yes to continue The upgrade will proceed and the success or failure of the upgrade will be reported If the update fails note any error messages and contact Sun Enterprise Services You will be asked Do you wish to halt the system now Answer no Start cmsconfig cd usr platform SUNW Ultra 4FT SUNWcms sbin cmsconfig Netra ft 1800 Interim Update Instructions September 1999 A CPU re enabled System in sync B CPU disabled Update the PROM DUU O A CPU upgrade completed Keep system up B 26 27 28 29 30 31 32 33 34 35 36 37 38
20. pnet SUNWspltr SUNWspltu Patch 2 Type verified showrev p grep 106929 Patch 106929 01 Obsoletes Requires Incompatibles Packages SUNWcsr v To Verify FPGA Firmware Levels FPGA revision 1 For each motherboard type verified cd usr platform SUNW Ultra 4FT SUNWcms sbin cmsfruinfo l x MBD i s EE MBD_ BRIDGE FWARE PARTNO EE MBD BRIDGE FWARE DASH where x is for motherboard A or B for motherboard B Record A MBD For both motherboards the output should be FPGA revision 2587134 07 Record B MBD or FPGA revision D 2587134 08 Both sides should be at the same revision level that is both 07 or both 08 Netra ft 1800 Interim Update Instructions September 1999 PROM verified Record A CPU PROM revision Record B CPU PROM revision Record version To Verify PROM Firmware Levels 1 For each CPUset type cd usr platform SUNNW Ultra 4FT SUNWcms sbin cmsfruinfo 1 x CPU i s EE CPU _PROM PARTNO EE CPU PROM_ DASH where x is A for A CPU or B for B CPU For both CPUsets the output should be 2587354 07 or 2587354 09 Both sides should be at the same revision level that is both 07 or both 09 2 Check the PROM version by typing prtconf V Record the version in the box In the following example OBP 3 7 23 0 1999 06 24 14 24 OBP 3 7 23 0 indicates version 23 The PROM should be version 21 for CP
21. previously installed in which case you will have circled Y following Step 5 on page 24 If you circled N ignore this step and proceed to Step 33 27 32 Backout the OSdog patch by entering the following at the DS D command line cd var sadm patch 107926 04 backoutpatch 107926 04 Y To Backout the Interim Update Patch Netra ft 1800 a 33 Backout the Netra ft 1800 Interim Update patch by entering the Interim Update following at the command line patch backed out cd var sadm patch 108145 10 backoutpatch 108145 10 Y To Back Out the Kernel Update Kernel Update 34 Backout the Kernel Update patch by entering the following at the patch backed command line out twice cd var sadm patch 105181 14 backoutpatch 105181 14 The following warning will be displayed WARNING usr sbin patchrm is being used to backout this patch Backoutpatch will be removed from Solaris patches in the next release of Solaris Checking installed packages and patches Backing out patch 105181 14 ERROR Patch number 105181 14 is not installed The backout script must therefore be executed a second time after which the patch will install correctly that is type 105181 14 backoutpatch 105181 14 28 Netra ft 1800 Interim Update Instructions September 1999 Y To Re install the OSdog Patch Perform this step only if the OSdog patch was backed out in step 31
22. que moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bailleurs de licence s il y en a Le logiciel d tenu par des tiers et qui comprend la technologie relative aux polices de caract res est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par l Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun AnswerBook Java le logo Jave Coffee Cup Netra Netra ft et Solaris sont des marques de fabrique ou des marques d pos es ou marques de service de Sun Microsystems Inc aux Etats Unis et dans d autres pays Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc L interface d utilisation graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconna t les efforts de pionniers de Xerox pour la recherche et le d veloppement du concept des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique Sun d tient une licence non exclusive de Xerox sur l interface d u
23. stem CMS To do this the patch installation process terminates the CMS daemon Do not attempt to use cmsconfig or other CMS utility until instructed to do so later in this installation procedure Reinstall QFE P 8 If you backed out the Sun QFE P patch 107778 as part of Step 3 patch you can now reinstall the patch m If the patch still resides in the var tmp directory type cd var tmp 107778 04 installpatch m If the patch no longer resides in the var tmp directory re install the patch as described in the Netra ft 1800 Software Release Notes part no 805 4527 13 13 Programmable Hardware Upgrade Note The upgrade utilities cannot be run if the system was booted from a read only device such as a CD ROM or a network the system must be running from a writable device such as a disk before this procedure can be performed In particular if the system has just been fully installed from CD ROM it should be rebooted from disk before performing this procedure Note If the FPGAs were upgraded using version 08 of the upgrade utility during the base software patch installation in Step 2 it is not necessary to repeat the procedure If you are not sure of the firmware version proceed to the next step Step 9 otherwise you can proceed directly to the PROM upgrade at Step 13 v To Upgrade the FPGAs The following procedure upgrades both motherboard A and motherboard B System in sync 9 Ensure the syst
24. tilisation graphique Xerox cette licence couvrant galement les licenci s de Sun qui mettent en place l interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences crites de Sun CETTE PUBLICATION EST FOURNIE EN L ETAT ET AUCUNE GARANTIE EXPRESSE OU IMPLICITE N EST ACCORDEE Y COMPRIS DES GARANTIES CONCERNANT LA VALEUR MARCHANDE L APTITUDE DE LA PUBLICATION A REPONDRE A UNE UTILISATION PARTICULIERE OU LE FAIT QU ELLE NE SOIT PAS CONTREFAISANTE DE PRODUIT DE TIERS CE DENI DE GARANTIE NE S APPLIQUERAIT PAS DANS LA MESURE OU IL SERAIT TENU JURIDIQUEMENT NUL ET NON AVENU Rb ax ga Adobe PostScript Netra ft 1800 Interim Update Instructions This document contains important release information for the software for the Netra ft 1800 Caution Read this document before attempting to install the system This document contains the following information m Prerequisites on page 6 a Verifying the Prerequisites Before You Start on page 7 m Patch Installation on page 11 m Programmable Hardware Upgrade on page 14 a To Enable or Disable the OSdog on page 19 m To Reset the System with the Upgrades on page 20 m Verifying the Upgrade on page 21 a Backing Out Strategy on page 24 a Functionality Addendum on page 31 a Documentation Changes on page 31 a Solaris Y2K Patch Compatibility on page 32 a CMS Control of the ICN Subsystem on page
25. tions on the icn objects They will then normally appear to be in state not_present icn_system 0 effectively encompasses the functionality of the existing icn control scripts icn init and icn terminate and can be used interchangeably with them A complete reset of the icn system can be accomplished by executing a disable followed by an enable on icn_system 0 Functionality Addendum 33 34 icn Each icn object controls a single icn network connection It can be enabled and disabled and also supports attributes that set the hostname of the network interface control whether the interface is up or down and determine how much memory is reserved for communication icn objects can only be enabled if icn_system 0 is also enabled The initial value for the hostname attribute is read from the corresponding icn configuration file in etc furthermore if the hostname is changed in the CMS the modified value is written back to the appropriate configuration file Note that the reverse is not true that is if the configuration file in etc is modified this will not be noticed by the icn CMS object in fact the change to the configuration file will be lost when the object is disabled since at that time the hostname from the CMS object is copied back to the configuration file When initially enabled automatically via an enable on icn_system 0 the initial state of each icn object depends upon the existing system state If the m
26. v auto boot true The OSdog is now permanently disabled 20 v To Reset the System with the Upgrades 50 A full power cycle of the system is required in order for the upgrades to take effect m If you are at the unix prompt type init 5 m If you are at the OBP prompt ignore this step and proceed with Step 51 System 51 Reset motherboard and side B using either of the following two power cycled methods m From the Remote Control Processor RCP enter the command BBoff Wait 10 seconds then enter the command BBon m Press the black standby power button on the side B bottom Control Alarms and Fans CAF module to power off Wait ten seconds then press the green button to power on 52 Reset motherboard and side A using either of the following two methods m From the Remote Control Processor RCP enter the command AAoff Wait 10 seconds then enter the command AAon m Press the black standby power button on the side A top Control Alarms and Fans CAF module to power off Wait ten seconds then press the green button to power on The system will boot up and come into sync Netra ft 1800 Interim Update Instructions September 1999 Verifying the Upgrade You can use the following instructions to verify that the patch installation procedure has been correctly applied If any of these verifications fail you should review the related steps in the procedure or consult
27. you wish to continue Answer yes to continue The upgrade will proceed and the success or failure of the upgrade will be reported If the update fails note any error messages and contact Sun Enterprise Services 26 Netra ft 1800 Interim Update Instructions September 1999 Keep system up cmsconfig started B CPU re enabled System in sync QFE patch backed out LJ J J 25 26 27 28 29 30 31 You will be asked Do you wish to halt the system now Answer no Start cmsconfig cd usr platform SUNW Ultra 4FT SUNWcms sbin cmsconfig Enter the item number for B CPU then select the Action item Press 1 to enable B CPU Wait for a few seconds then press Return to redisplay the menu Repeat until the display shows that B CPU is enabled then press q to return to the cmsconfig menu Wait for the system to come back into sync This may take a few minutes To verify follow the procedure To Confirm the System is Running in Sync on page 11 To Backout the QFE Patch The following step applies only if the QFE patch number 107778 was previously installed If the patch was not installed ignore this step and proceed to Step 32 Backout the QFE patch by entering the following at the command line cd var sadm patch 107778 04 backoutpatch 107778 04 To Backout the OSdog Patch The following step applies only if the OSdog patch number 107926 was

Netra ft 1800 Interim Update Instructrions

Contents

Download Pdf Manuals

Related Search

Related Contents