Model 700TC(I)
Contents
1. FINISHED HEIGHT OF 80 2032 IS TO TOP OF SUB ZERO MOLDING DECORATIVE VALANCE CANNOT EXTEND BEYOND THE FRONT OF THIS PLANE DECORATIVE VALANCE eee REMOVABLE MOLDING BY SUB ZERO TOP HINGE Dimensions in parentheses are in millimeters unless otherwise specified 12 SUB ZERO Model 700TC I INTEGRATED TOE KICK AREA DETAIL v Planning Information TOE KICK CLEARANCE The toe kick clearance can vary with the height of the lower drawer panel the maximum panel height is 1611 16 424 IMPORTANT NOTE You must keep a minimum space of 4 102 clear below the bottom edge of the lower drawer panel so the unit can be properly vented In addition any decorative base molding must be removable for possible servicing and cleaning of the condenser The illustration below shows the area below the lower drawer where the operating mechanical equipment of the Integrated unit is housed IMPORTANT NOTE The depth of each Integrated unit is 24 610 from the front of the unit to its back Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit This will require a minimum rough opening depth of 25 635 Refer to the illustration 10 268 PANEL 164 424 PANEL 10 254 OPTIONAL BASE MOLDING MUST BE REMOVABLE 67 5 a 23 To 4 gt 102 iia FLOOR 24 TO WALL A Dimensions in parenthese2. meg eee f Bp A Ea 9 A 139 16 e C l 345 A a 341 4 Po JE EZ K J E i Ka ot A 38 oo Aerm rrr A _ _g t Ja 11 joe ra x x 4 n J FRONT VIEW k 4 Mice INTEGRATED Installation of an Integrated tall unit within framed cabinetry Dimensions may vary Dimensions in parentheses are in millimeters unless otherwise specified SUB ZERO Planning Information Model 700TC I INTEGRATED FRAMELESS CABINETRY V x 263 4 679 gt PANEL WIDTH 453 8 1153 1611 16 424 FRAMELESS CABINETRY APPLICATIONS The illustration below shows a hypothetical installation of a Integrated tall unit within frameless cabinetry Review the illustration giving particular attention to the overall panel specifications Also refer to the full scale illustrations at the end of this section for specifics on door openings IMPORTANT NOTE Dimensions are based on a 1 8 3 reveal A reveal of up to 1 4 6 is possible but panel dimensions need to be adjusted accordingly 24 gt 610 lt 27 gt TOE KICK 686 FINISHED OPENING A ALL REVEALS ARE 1 8 3 Installation of an Integrated tall unit within frameless cabinetry Dimensions may vary Dimensions in parentheses are in millimeters unless otherwise specified SIDE VIEW DIMENSIONS MAY VARY SUB ZERO Planning Information
3. DUAL INSTALLATIONS If two or more Integrated models are installed side by side where there is 2 51 or less of space between the units a heater kit is recommended TTDUAL for two tall units installed side by side and BBDUAL for two base units or a base unit and a tall unit installed side by side These optional compo nents are available through your Sub Zero dealer To obtain local dealer information visit the Locator section of our website subzero com 11 SUB ZERO Planning Information Model 700TC I INTEGRATED UPPER VALENCE DETAIL DOOR PANEL HEIGHT The height of the door panel can grow beyond 453 8 1153 and exceed the 80 2032 overall height as long as you stay below the recommended door panel weight limit of 40 Ibs 18 kg for 27 868 wide units and 53 Ibs 24 kg for the Model 736TC I The illustration below shows how the panel may grow and what you need to consider doing to finish the area in back of the door panel IMPORTANT NOTE The valance you use to finish the area behind the door panel must stay behind the front plane of the finished molding as shown in the illustration IMPORTANT NOTE The depth of each Integrated unit is 24 610 from the front of the unit to its back Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit This will require a minimum rough opening depth of 25 635 Refer to the illustration 25 TO WALL
4. 131 o _ BRACKET INTEGRATED 25 343 o 27 343 27 ED 1 9 7 u 9 L 9 lt 151 2 gt lt 9 gt 394 229 WATER LINE SIDE ENTRY WATER LINE LOCATIONS I BOTTOM ENTRY P LOCATION eE a gt lt 11 2 gt lt 11 2 38 38 LOCATE ELECTRICAL WITHIN SHADED AREA ORIENT GROUND PRONG TO RIGHT AS SHOWN ANTI TIP LOCATE WATER LINE BRACKET REAR ENTRY WITHIN SHADED AREA a 18 830 gt 1 4 229 a L212 ea 19 151 2 394 gt WATER LINE NOTE ANTI TIP BRACKET MUST BE INSTALLED TO SIDE ENTRY PREVENT UNIT FROM TIPPING FORWARD ANTETIR LOCATION BRACKET FRONT VIEW SIDE VIEW Dimensions may vary by 1 s 3 DIMENSIONS v Finished Rough Opening Width 27 686 Finished Rough Opening Height 80 2032 Finished Rough Opening Depth 25 635 Location of Electrical Within shaded area Location of Plumbing Model 7OOTCI only Within shaded area The depth of the Model 7OOTC I is 24 610 from the front of the unit to its back Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit This will require a minimum rough opening depth of 25 635 See Installation Instructions shipped with unit for detailed specifications Dimensions in parentheses are in millimeters unless otherwise specified SUB ZERO Planning Information Model 700TC I INSTALLATION NOTES gt Refer to the illustrations and spe
5. Model 7OOTC I PANEL CONSIDERATIONS The illustrations below provide panel width dimensions for installation of a single tall unit and for installing two tall units side by side IMPORTANT NOTE Dimensions are based on a 1 8 3 reveal A reveal of up to 1 4 6 is possible but panel dimensions need to be adjusted accordingly A CAUTION When s 16 or thicker panels are used and a reveal less than 1 4 6 is maintained the door panels may cause damage to the Sub Zero unit when the door is open at the maximum 105 door stop You should use the built in 90 door stop to prevent damage 27 si lt 686 i g 3 min p 263 679 REVEAL gt k i J L II r i 3 19 PANEL i I Tf oe i 254 esn gt APPLIANCE CABINETRY II OR SDE ean DOOR WIDTH PANEL toBack OF UNIT i l iI i i SUB ZERO I UNIT l sl 3 g 3 min m REVEAL 25 ep CABINETRY OR SIDE PANEL 7 SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL OF UNIT SUB ZERO a Dimensions in parentheses are in millimeters unless otherwise specified SUB ZERO UNIT lt 54 1372 t gt 1 i lt 2613 681 gt k 2618 681 gt 4 F g 3 min 16 3 16 g 3 min REVEAL gt k min II k REVEAL F REVEAL 7 3 19 P
6. finished rough opening depth if you want the front panel to be flush with surrounding cabinetry You may have to move the unit back into drywall or bring the cabinets forward to achieve a flush fit Refer to the illustrations Illustrations on the following pages give dimensions for an Integrated base or tall unit installed within a framed cabi netry beaded inset application Review the illustrations giving particular attention to the overall panel specifica tions Also refer to the full scale illustrations at the end of this section for specifics on door openings SUB ZERO Planning Information Model 700TC I FRAMED CABINETRY BEADED INSET APPLICATION y 24 GW SUB ZERO TO WALL CABINET DOOR DOOR PANEL A A TOP VIEW M RS gt 263 4 679 gt The illustration shows an Integrated tall unit installed within a framed cabinetry beaded inset application IMPORTANT NOTE Dimensions are based on a 1 8 3 reveal A reveal of up to 1 4 6 is possible but panel dimensions need to be adjusted accordingly A ALL REVEALS ARE 1 8 3 B DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS C BOTTOM RAIL MUST BE REMOVABLE DIMENSIONS MAY VARY PANEL WIDTH ZLLLLLLL po O A Hel A 38 ILo N 4 ae y ae y y Wy f A p 477 8 4 4 4 1216 2624 SHADED AREA 4 INDICATES STATIONARY A 4 STYLES AND RAILS A A Ae A 2032 Y
7. 24 back or cabinets forward to achieve a flush fit TO LINE OF INTERFERENCE aaa ade nso 105 maximum door opening 1 4 scale top view Adjacent side panel and countertop application LINE OF INTERFERENCE 1 MiN gt AT MAXIMUM DOOR OPENING REVEAL MOUNTING BRACKET SCREW 3 Zi A PANEL Ie lt a 25 657 APPLIANCE DOOR WIDTH wor SUB ZERO DOOR Do o ie TO BACK OF UNIT LINE OF INTERFERENCE SIDE MOLDING AND INSTALLATION HARDWARE PROVIDED BY SUB ZERO INTEGRATED T Door closed full scale top view If the panel is thicker than 3 4 19 it is recommended that you utilize the built in 90 door stop to prevent damage to the panel and face frame Dimensions in parentheses are in millimeters unless otherwise specified 15
8. 4 618 248 et es eS ee _ 4 FRONT VIEW 102 SIDE VIEW 1 2 13 ADJUSTMENT IN LEVELING LEGS Dimensions may vary by s 3 Dimensions in parentheses are in millimeters unless otherwise specified Door alarm will let you know with an audible beeping if a door or drawer is left open Adjustable spill proof glass shelves Refrigerator deli drawer for storage of smaller items The exclusive dual action hinge has a built in 90 door stop Meets strict Department of Energy requirements UL approved for US and Canada Two five and twelve year residential warranty exclusions apply warranty information can be found on our website subzero com INTEGRATED 24 610 DOOR DRAWER DOOR DRAWER CLOSED CLOSED 1 i i 191 2 90 251 2 495 ee 648 90 DOOR OPENING MAXIMUM DOOR OPENING TOP VIEW DOOR DRAWER PANEL THICKNESS NOT INCLUDED DIMENSION WILL VARY WITH INSTALLATION SUB ZERO Planning Information Model 700TC I INTEGRATED MODEL OPTIONS v Over and Under Refrigerator Freezer 700TC Over and Under Refrigerator Freezer with Automatic Ice Maker 7OOTCI PANEL OPTIONS v Integrated custom panels Classic Stainless Steel Finish S Platinum Stainless Steel Finish P Carbon Stainless Steel Finish B Stainless steel door and drawer front panels are ordered and shipped as sales ac
9. ANEL I Ki 25 Il 25 Z S CABINETRY y CABINETRY OR SIDE ety OR SIDE PANEL TO BACK j PANEL SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL INTEGRATED Panel width dimensions for installation of a single tall unit Panel width dimensions for installation of two tall units side by side 10 SUB ZERO Planning Informati Model 700TC I on CABINETS TOP VIEW gt Installation without side panels 27 E MINIMUM 5 8 16 SIDE PANELS gt lt gt Installation with side panels CABINETS Waa GEE TOP VIEW gt Installation of two units side by side CABINETS 27 E MINIMUM 5 8 16 SIDE PANELS gt gt Installation at end of run Dimensions in parentheses are in millimeters unless otherwise speci fied INTEGRATED INSTALLATION OPTIONS The illustrations on this page show some typical installations and their dimension considerations The depth dimension in the illustrations may vary depending on cabinet styles treatment of counter tops or other design options IMPORTANT NOTE The depth of each Integrated unit is 24 610 from the front of the unit to its back Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit This will require a minimum rough opening depth of 25 635 Refer to the illustrations
10. SUB ZERO Planning Information Model 700TC I Over and Under Refrigerator Freezer INTEGRATED Model 700TC Model 700TCI with Ice Maker Electronic digital control panel Adjustable spill proof glass shelves Adjustable glass shelf and deli drawer Stationary shelf Location of serial number Automatic ice maker Model 700TCI Front venting with removable kickplate gt The Sub Zero Model 7OOTC and 7OOTCI integrated design accepts custom wood or stainless steel door and drawer panels Stainless steel panels and handles are available as sales accessories in three finishes classic platinum and carbon Dimensions in parentheses are in millimeters unless otherwise specified 10 05 Seamless molding Adjustable dairy compartment Adjustable door shelves Egg container Magnetic door drawer gaskets Upper freezer storage drawer Lower freezer storage drawer With the installation of a harness kit these appliances are Star K compliant to meet strict religious regulations in conjunction with specific instructions found on star k org You may purchase this harness kit through your Sub Zero dealer To obtain local dealer information visit the Locator section of our website subzero com F those very small galley kitchens where you cannot fit a full size Built In unit would beg anyone to say they do not have room for this delightful c
11. cessories and include tubular handles ACCESSORIES gt Tubular handles in classic platinum and carbon stainless steel gt Shelf and crisper assembly gt Dozen egg container with lid gt Dual installation heater kit TTDUAL or BBDUAL Accessories are available through your Sub Zero dealer To obtain local dealer information visit the Locator section of our website subzero com Dimensions in parentheses are in millimeters unless otherwise specified SPECIFICATIONS v Model 700TC I Over and Under Refrigerator Freezer Overall Width 27 686 Overall Height 80 2032 Overall Depth 24 610 Refrigerator Capacity 10 2 cu ft 289 L Freezer Capacity 5 1 cu ft 144 L Minimum Height levelers in 79 1 2 2019 Door Clearance 25 1 2 648 Drawer Clearance 191 2 495 Electrical Requirements 115 V AC 60 Hz 15 amp circuit Plumbing Requirements 1 4 copper line Water Supply 20 100 psi 540 kWh 45 360 Ibs 163 kg Annual Energy Usage Shipping Weight Special Note Door and drawer panels and handles are available in three stainless steel finishes Specifications are subject to change without notice SUB ZERO Planning Information Model 700TC I INSTALLATION SPECIFICATIONS i TOP VIEW TOP VIEW a ANTETIP L 11 2 BRACKET A ANTI TIP BRACKET 68 131 2
12. cifications for overall dimensions finished rough opening dimensions and installation specifics gt The depth of Model 7OOTC I is 24 610 from the front of the unit to its back Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit This will require a minimum rough opening depth of 25 635 Refer to the installation illustration gt The anti tip bracket must be installed to prevent the unit from tipping forward gt Integrated units are compatible with virtually any style of cabinetry They can be used with framed as well as frameless cabinets gt Refer to the full scale illustrations at the end of this section for specifics on panels and door openings gt Door panels can grow beyond the 80 2032 height to accommodate any size of door as long as you stay below the recommended door panel weight limit of 40 Ibs 18 kg Door panels must be a minimum of 5 8 16 thick gt The weight of each drawer panel cannot exceed 12 Ibs 5 kg Drawer panels must be a minimum of 5 8 16 thick gt For the bottom drawer the maximum panel height is 1611 16 424 You must keep a minimum space of 4 102 clear below the bottom edge of the lower drawer panel so the unit can be properly vented In addition any decorative base molding must be removable for possible servicing and cleaning of the condenser gt We recommend using D style handles which should be located on the oppos
13. e models can be used with framed as well as frameless cabinets Because of the precise application and the look you may want to achieve there are important questions you need to answer before ordering panels for the doors and or drawers As you look at styles of cabinets keep some important facts in mind Weight Limitations The door panel cannot exceed 40 Ibs 18 kg and each drawer panel must not exceed 12 Ibs 5 kg Panel Thickness Door and drawer panels must be a minimum of 5 8 16 thick The height of the door panel can grow beyond 453 8 1153 and exceed the 80 2032 overall height as long as you stay below the recommended door panel weight limit The toe kick clearance can vary with the height of the lower drawer panel the maximum panel height is 1617 16 424 You must keep a minimum space of 4 102 clear below the bottom edge of the lower drawer panel so the unit can be properly vented We recommend using D style handles For the cabinet door handles must be located near the edge of the panel opposite the hinge centered top to bottom Locate handles in the top center area of the drawer panels IMPORTANT NOTE The depth of each Integrated unit is 24 610 from the front of the unit to its back You must allow for the thickness of the panel you are applying when planning for the finished rough opening depth if you want the front panel to be flush with surrounding cabinetry You may have to move the unit back int
14. essor tray The tray must be slid forward for service gt Regardless of the routing allow for 27 686 of excess copper tubing to remain outside the wall or floor for easy connection to the unit as shown in the installation illustration gt A115 volt GOHz 15 amp circuit breaker and electrical supply are required A separate circuit servicing only this appliance is necessary gt All Integrated models are equipped with a power supply cord with a 3 prong grounding plug which must be plugged into a mating 3 prong grounding type wall receptacle The electrical outlet must be placed so the ground ing prong is to the right of the thinner blades The outlet must be flush with the back wall Locate electrical within the shaded area shown in the installation illustration gt Do not use an extension cord or two prong adapter Electrical ground is required gt You must follow all National Electrical Code regulations In addition be aware of local codes and ordinances when installing your service gt The Integrated Installation Guide packed with the appliance will give you step by step proce dures for making sure the unit is installed properly SUB ZERO Planning Information Model 700TC I INTEGRATING CABINETRY INTEGRATED Dimensions in parentheses are in millimeters unless otherwise specified CABINETRY APPLICATIONS Integrated refrigeration is compatible with virtually any style and look of cabinetry Th
15. ite side from the hinge centered on the cabinet door and the top center area of the drawer panel gt Two Integrated units may be installed next to one another Refer to page 11 for additional information gt For Integrated models with an automatic ice maker rough in the water supply line Connect a 1 4 OD copper line to the house supply being sure to use an easily accessible shut off valve between the supply and the unit This shut off valve should not be installed behind the unit Dimensions in parentheses are in millimeters unless otherwise specified gt Do not use self piercing valves A saddle valve kit 4200880 is available from your Sub Zero dealer To obtain local dealer informa tion visit the Locator section of our website subzero com gt Aline filter is required when water condi tions have a high sediment content The ice maker operates on water pressure of 20 psi 1 4 bar to 100 psi 6 9 bar In some cases a reverse osmosis water filter system may not be able to maintain the minimum water pressure consistently gt When routing the water through the side walls you must place the water line within 1 2 13 of the floor and as close as possible to the back wall The line must be routed around the anti tip bracket so it clears the bracket and leveling feet of the unit Refer to the installation illustration for placement of the water line gt Do not route water supply line in front of the compr
16. o drywall or bring the cabinets forward to achieve a flush fit A CAUTION As the reveal between cabinets and the Integrated unit decreases the potential exists for severe finger pinching or crushing if a hand or fingers are placed in the opening when the door is closing SUB ZERO Planning Information Model 700TC I INTEGRATING CABINETRY E INTEGRATED FRAMED CABINETRY v SUB ZERO CABINET UNIT TO WALL FRAME CABINET DOOR gt Traditional Frame full overlay 24 SUB ZERO CABINET UNIT TO WALL FRAME CABINET 1 8 3 PANEL DOOR REVEAL gt Traditional Frame standard overlay 24 SUB ZERO UNIT TO WALL CABINET FRAME _ ___ as CABINET DOOR gt Traditional Frame 3 8 10 offset Dimensions in parentheses are in millimeters unless otherwise specified FRAMED CABINETRY APPLICATIONS Framed cabinetry applications present you with different questions to address The illustrations on this page show common applications of framed cabinetry These are not meant to be the only alternatives but are suggestions from designers around the country Also refer to the full scale illustrations at the end of this section for specifics on door openings IMPORTANT NOTE The depth of each Integrated unit is 24 610 from the front of the unit to its back You must allow for the thickness of the panel you are applying when planning for the
17. ombina tion model The refrigerator door space gives you 10 2 cu ft 289 L of storage with a temperature range of 34 F 1 C to 45 F 7 C while the two freezer drawers give you 5 1 cu ft 144 L of storage in an environment where the temperature can be set between 5 F 20 C and 5 F 15 C You also have the option of ordering this model with or without an ice maker You must specify the door swing when placing an order SUB ZERO Planning Information Model 700TC I FEATURES gt Tall combination unit with upper cabinet refrigerator and freezer storage drawers gt Model 7OOTCI has automatic ice maker gt Integrated design for point of use refriger ation anywhere in the home gt Dual refrigeration system with two distinct temperature zones ensures the freshest food and energy efficiency gt Electronic digital controls are up front and easy to use gt Flat to the ceiling bright lighting in cabinet and drawers OVERALL DIMENSIONS v 27 24 CGJ Topor l UNIT DIMENSION ROUGH UNIT DIMENSION lt 14 a56 OPENING I 7 K 1 Al o j e sip 21 _ DOOR g MOUNTING DETAIL 80 z J 2032 3e IID l 789 16 10 jj 1995 HE E S f t 131 4 DRAWER 1 2 337 MOUNTING DETAIL 13 P ewa araa t o o o O prs 10174 876 260 S eee E 203 8 t 93
18. s are in millimeters unless otherwise specified 13 SUB ZERO Planning Information Model 700TC I FULL SCALE TEMPLATE FRAMED CABINETRY IMIPORTANT NOTE The depth of unit is 24 610 from the front of back Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit TOBAGK SUB ZERO DOOR each Integrated the unit to its LINE OF INTERFERENCE OF UNIT LINE OF INTERFERENCE _ 105 maximum door opening 1 4 scale top view AT MAXIMUM DOOR OPENING i STN 5E 610 TO BACK YV OF UNIT h FLUSH FURNITURE FINISH MOUNTING BRACKET SCREW x 25 657 APPLIANCE DOOR WIDTH gt SUB ZERO DOOR ee o LINE OF INTERFERENCE SIDE MOLDING AND INSTALLATION HARDWARE PROVIDED BY SUB ZERO INTEGRATED Door closed full scale top view Dimensions in parentheses are in millimeters unless otherwise specified If the panel is thicker than 3 4 19 it is recommended that you utilize the built in 90 door stop to prevent damage to the panel and face frame SUB ZERO Planning Information Model 7OOTC I SUB ZERO DOOR FULL SCALE TEMPLATE 3 4 19 DOOR PANEL COUNTERTOP SIDE PANEL FRAMELESS CABINETRY IMPORTANT NOTE The depth of each Integrated unit is 24 610 from the front of the unit to its back Your design may necessitate moving the unit
Download Pdf Manuals
Related Search