315W Installation Guide - Sub
Contents
1. rative door panel to match surrounding cabinetry The door panel and handle will be provided by the customer Refer to the chart for overlay panel specifications For overlay panel handle hardware we recommend a D style handle centered top to bottom along the edge opposite the hinge You may have to countersink screw heads to ensure hardware does not interfere with panels fitting flush with unit doors Additional panel information can be found in the wine storage section of the Sub Zero design guide or check our website at subzero com A CAUTION A solid panel cannot be installed over the glass door as this may cause moisture to form behind the panel Panel Specifications OVERLAY PANEL w H Panel Dimensions 15 381 301 16 764 Width of Rails and Stiles 21 4 57 min Panel Thickness 5 8 16 min Panel Weight 10 Ibs 5 kg max Model 315W Installation Overlay Panel Installation Inspect the overlay door panel for minimum thickness weight limit and finished inside edges Decide if the handle will be attached through the glass door frame or just through the decorative door panel If it is just through the door panel the handle must be attached first The overlay panel is attached using 8 x 5 8 square drive screws passing through the door frame from the rear behind the gasket into the panel The panel is marked for screw locations by the use of tenon centers which are temporarily inserted into the 1 4 6 diameter2. 118 Ibs 54 kg Model 315W Specifications 5 Area Requirements Before moving the unit into place make sure the opening dimensions door clearance and electrical service are correct Refer to the illustrations on the previous page IMPORTANT NOTE For corner installations door swing may be limited due to handle contact with the adjacent wall or cabinet You must allow a minimum of 2 61 from the wall for a 90 door opening This will ensure that the wine shelves can be fully extended A CAUTION Wine bottles are heavy A fully loaded unit will weigh over 200 Ibs 91 kg Be sure the subflooring is adequate for the weight of both the unit and its contents AWARNING Model 315W is intended for indoor use only subzero com specs Electrical Requirements Model 315W must be installed with adequate clearance for electrical connection at the rear of the unit The elec trical supply requires installation of a grounded receptacle on a separate circuit servicing only this appliance A ground fault circuit interrupter GFCI is not recommended and may cause interruption of operation Follow the National Electrical Code and local codes and ordinances when installing the receptacle IMPORTANT NOTE Although it can be located anywhere on the back wall it is recommended that the receptacle be placed in an adjacent cabinet or in the lower right of the opening If it is placed within the opening additional cabinet depth may be
3. the installation to make the process easier problem free and most importantly safe The homeowner should keep this installation guide for future reference Any questions or problems regarding the installation should be directed to your authorized Sub Zero dealer or Sub Zero customer care at 800 222 7820 You may also check the contact amp support section of our website subzero com Location of rating plate Important product information including the model and serial number of your unit are listed on the product rating plate located on the underside of the top wall Refer to the illustration Model 315W Specifications 4 Model 315W Specifications OVERALL DIMENSIONS INSTALLATION 151 8 384 lt lt 24 610 gt ee DD TOP VIEW A 24 610 OPENING DEPTH 341 16 865 7 y 4 102 lt 24 610 gt 341 2 876 151 4 gt OPENING DEPTH OPENING 387 HEIGHT OPENING WIDTH 165 8 422 SIDE VIEW FRONT VIEW 13 4 44 Overall dimensions are based on stainless steel panels IMPORTANT NOTE It is recommended that the electrical NOTE Door swing is not reversible supply be placed in an adjacent cabinet If it is placed within the opening additional cabinet depth may be required Specifications Wine Storage Capacity 26 bottles 750 ml Shipping Weight
4. INSTALLATION GUIDE Model 315W Wine Storage SUB ZERO Contents Model 315W Wine Storage 3 Model 315W Specifications 4 Model 315W Installation 6 Installation Checklist 10 Service Information 11 Features and specifications are subject to change at any time without notice Visit subzero com specs for the most up to date information IMPORTANT NOTE Throughout this guide dimensions in parentheses are millimeters unless otherwise specified Important Note To ensure the safe and efficient installation of Sub Zero equipment please take note of the following types of highlighted information throughout this guide IMPORTANT NOTE highlights information that is especially relevant to a problem free installation CAUTION signals a situation where minor injury or product damage may occur if instructions are not followed WARNING states a hazard that may cause serious injury or death if precautions are not followed SUB ZERO Sub Zero Model 315W Wine Storage 3 subzero com specs Model 315W Wine Storage IMPORTANT NOTE The importance of the installation of the undercounter wine storage unit cannot be overem RATING PLATE phasized Installation must be completed by a qualified installer Read this entire installation guide prior to installation There are key details that you should observe during
5. collectively the Company Marks All other trademarks or registered trademarks are property of their respective owners in the United States and other countries SUB ZERO SUB ZERO INC 44848 MADISON WI 53744 SUBZERO COM 800 222 7820
6. d over the holes on the inside surface of the door CAUTION The cover patches or plugs are part of the insulation system on the door of the wine storage unit Be sure to cover all the holes in the door that were used 10 Installation Checklist To ensure a safe and proper installation the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked Has all packing material been removed Turn the unit on Is it operating properly If not is the unit plugged in Is the control turned on Has the unit been secured in place with the anti tip bracket Is the unit level Are all leveling legs making contact with the floor Is the power cord plugged into a properly grounded 3 prong outlet which has been installed in accordance with all applicable electrical codes Is the kickplate installed properly Is the door panel attached securely and properly aligned Is the door aligned for proper appearance and operation Have any installation or service problems been noted on the product registration card Has the registration card been mailed in Has the stainless steel door been inspected for any imperfections This is to be done by the dealer or installer with the customer upon completion of the installation Stainless steel panels are covered by a limited 60 day parts and labor warranty for cosmetic defects Service Information Service Information If
7. e of the door This is to accommodate Sub Zero accessory handles and provide for easy attach ment of the handle through the door frame If you choose not to use the pre drilled handle mounting holes it will be necessary to fasten the handle from the rear of the door panel only or drill one or more additional holes through the metal frame of the door The cross section illustration shows how the hole passes through the door frame The hole center is on the small locator groove in front of the frame A 1 4 6 diameter hole is made in the front wall of the extrusion and a 13 32 11 diameter hole through the rest of the frame A CAUTION Exercise caution when drilling holes for mounting the panel to the door frame Model 315W Installation Overlay Panel Installation CAUTION The model 315W glass door is made with a sealed double wall tempered glass core The drill must not contact this core when drilling Be sure the hole is centered on the small groove in the front of the door frame and the drill passes squarely through the frame If you are inexperienced with drilling fasten the handle from the rear of the door panel only IMPORTANT NOTE Install screws in all the mounting holes in the door frame The nature of the door panel with a narrow outer rim and no connecting center member requires the support provided by the glass door After the door panel installation is complete apply the cover patches or plugs provide
8. ed back in the installation opening Using an adjustable wrench or pliers turn each of the four leveling legs clockwise to raise the unit and counterclock wise to lower the unit For the location of the leveling legs refer to the illustration below il LEVELING LEG Adjust leveling legs subzero com specs To determine the horizontal or vertical level point place a 2 6 m level along the top of the unit or on either exterior side of the unit In order to access these leveling posi tions the unit will have to be slightly out of the opening AWARNING To reduce the possibility of the unit tipping forward the front leveling legs must be in contact with the floor POSITION THE UNIT Slide the wine storage unit back into position in the installation opening IMPORTANT NOTE Model 315W has been designed to be serviced in place but in some cases it may be necessary to pull the unit out for service If a floor is to be installed after the unit has been installed spacing shims equal to the thickness of the floor should be installed under the unit to keep it level with the floor Turn power back on to the electrical outlet Model 315W Installation Kickplate INSTALL KICKPLATE Once the wine storage unit is in position install the kick plate using the screws provided Refer to the illustration There is some adjustment to the mounting assembly so that the kickplate wi
9. flooring with appropriate materials and secure the door closed Anti Tip Bracket To prevent the unit from tipping forward and provide a stable installation the unit must be secured in place with the anti tip bracket An anti tip bracket and hardware is provided with model 315W Placement of the anti tip bracket is critical to a stable installation The anti tip bracket must be installed securely Attach the anti tip bracket to the top of the unit opposite the hinge side The bracket offset flange should be facing up with the two oblong holes in the front Once the unit is moved into position open the door and secure the anti tip bracket to the countertop Refer to illustration below ANTI TIP BRACKET Anti tip bracket Model 315W Installation 7 Installation IMPORTANT NOTE If the wine storage unit has been laid on its back or side you must allow the unit to stand upright for a minimum of 24 hours before connecting power With the wine storage unit near the installation opening plug the power supply cord into the electrical outlet With power applied to the unit check for lighting and cooling Once you are satisfied that the unit is operating properly shut off power to the electrical outlet at the circuit breaker and proceed AWARNING Shut off power to the electrical outlet LEVEL THE UNIT Level the wine storage unit before sliding it into position Leveling cannot be completed with the unit push
10. holes the front of the door frame Refer to the illustration below With the unit secured in place and the door closed hold the panel in the desired position on the door and rap by hand from the front putting center marks on the rear surface of the panel If the door panel is made of such a material that pre drilling is needed all of the mounting holes should be marked If not only enough holes to hold the panel in place temporarily are necessary GASKET 13 32 11 NT DIAMETER DIAMETER TENON CENTER 1 Tenon centers Door frame cross section 9 subzero com specs Remove the door panel from the door frame and remove tenon centers Open the door Using the center marks to locate screws drive the screws into the panel through the black tape on the door frame The screw holes inside the door are hidden under a cover flap on the door gasket It is necessary to lift the flap to insert the screws Use as many screws as necessary to hold the door panel in place securely IMPORTANT NOTE After the first three or four mounting screws are in place but not completely tightened close the door and check the panel fit This is the time to make small adjustments Once you are satisfied with the appear ance open the door and add the rest of the screws Check all screws for tightness The metal frame on the door has numerous mounting holes on each sid
11. ll fit flush with the surrounding area The kickplate must be removed for servicing The floor cannot interfere with removal Do not cover the vents of the kickplate to allow proper airflow If you choose the kickplate may be painted another color Follow these steps Rough up the surface to be painted with fine grit sandpaper Wipe with alcohol to ensure that the surface is clean and dry Use an appliance or industrial grade oil base high gloss enamel paint KICKPLATE AIRFLOW Model 315W uses a fan to take in room air through vents in the left side of the kickplate and discharges warm air through vents in the right side These vents must be kept clear of obstructions or decorative panels Blocking or obstructing the kickplate will restrict airflow and cause a decrease in performance and efficiency Refer to the illustration below IMPORTANT NOTE The minimum air temperature the wine storage unit will operate in is 50 F 10 C and the maximum is 100 F 38 C WARM AIR OUT ROOM AIR IN KICKPLATE Install kickplate Kickplate airflow Panel Specifications Model 315W is offered in two design applications stain less steel S and overlay O Each of these designs have a full view glass door The stainless steel model 315W S is shipped from the factory with the decorative stainless steel door panel and matching handle in place The overlay model 315W O is designed to accept a deco
12. required Refer to the illustrations below A WARNING Do not use an extension cord or two prong adapter Electrical ground is required on this appliance Electrical Requirements Power Supply 115 V AC 60 Hz Receptacle 3 prong grounding type Circuit Breaker 15 amp GROUNDING GROUNDED ELECTRICAL OUTLET Location of electrical supply Electrical ground Model 315W Installation Unpack the Unit Before moving the wine storage unit into position make sure the opening dimensions and electrical requirements are complete and accurate IMPORTANT NOTE The floor under the wine storage unit must be at the same level as the surrounding finished floor to allow for removal of the unit for servicing Use an appliance dolly to move the wine storage unit near the installation opening Position the dolly at the side of the unit to prevent damage to finished surfaces Remove and discard all packing materials and tape IMPORTANT NOTE Do not discard the kickplate anti tip bracket and hardware These items will be needed for the installation The roller assembly wine shelves should be removed to reduce weight and prevent them from rolling To remove pull the shelf out to its full extension gently and evenly lift up on both sides of the front of the shelf and remove Reverse the procedure to reinstall the shelf A CAUTION Before moving the wine storage unit into position protect any finished
13. service is necessary maintain the quality built into your wine storage unit by calling Sub Zero factory certified service For the name and number of Sub Zero factory certified service nearest you check the contact amp support section of our website subzero com or call Sub Zero customer care at 800 222 7820 When calling for service you will need the model and serial numbers of your unit Both numbers are listed on the product rating plate located on the underside of the top wall Refer to the illustration below RATING PLATE Location of rating plate 11 subzero com specs WARNING If you are storing or disposing of your old refrigerator or freezer please do it safely Remove the doors or tightly secure the doors closed Child entrapment accidents can be tragic ji SUB ZERO The information and images in this guide are the copyright property of Sub Zero Inc Neither this guide nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub Zero Inc Sub Zero Inc all rights reserved Wolf Wolf 8 Design Wolf Gourmet W amp Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance Inc Sub Zero Sub Zero amp Design Dual Refrigeration Constant Care and The Living Kitchen are registered trademarks and service marks of Sub Zero Inc
Download Pdf Manuals
Related Search