Stihl Cut-off Machine Safety Manual
Contents
1. 162. Wet or dry cutting is possible With wet cutting you get a longer life of your wheel Water attachments are available for your STIHL cut off machine See the appropriate section of your owner s manual A Warning Do not remount a used diamond abrasive wheel without first inspecting for under cutting flatness core fatigue segment damage or loss signs of overheating discoloration and possible arbor hole damage Check the wheel for cracks and make sure that no pieces have broken off the wheel before use Always fit the wheel so that the arrow on the wheel points in direction of the rotation of the spindle THE USE OF THE CUT OFF MACHINE Transporting the Cutquik Warning Always stop the engine before putting a cut off machine down or carrying it The abrasive wheel continues to rotate for a short while after the throttle trigger is released flywheel effect Carrying a cut off machine with the engine running is extremly dangerous Accidental acceleration of the engine can cause the wheel to rotate Avoid touching the hot muffler By hand When carrying your cut off machine by hand the engine must be stopped and the cut off machine must be in the proper position Grip the front handle and place the muffler at the side away from the body A Warning Always protect the cutting wheel from hitting the ground or any other objects Damaged wheels may shatter and cause serious or fatal injury By vehicle Prop
3. 12 Cutting Wheel 13 Decompression valve 337BA012 14 Adjusting Lever of Wheel Guard 15 Muffler 16 Tensioning nut V belt tensioning system 17 Starter Grip 18 Fuel Filler Cap ise Q q lt a N p Definitions 1 Rear Handle The support handle for the right hand 2 Air Filter Prevents dust and foreign matter from entering the carburetor 3 Wingnut of Filter Cover For removing filter cover permits filter to be cleaned 4 Throttle Trigger Interlock Must be depressed before activating the throttle trigger 5 Throttle Trigger Controls the speed of the engine 6 Choke Lever Eases engine starting by enriching mixture 7 Slide Control Starting throttle lockand stop switch Keeps the throttle partially open during starting switches the engine s ignition off and stops the running of the engine 8 Spark Plug Boot Connects thespark plug with the ignition wire 9 Front Handle Handle bar for the left hand at front of cut off saw 10 11 12 13 14 15 16 17 18 Wheel Guard Clutch Guards the wheel and deflects Couples engine to the V belt pulley sparks when engine is accelerated beyond idle speed Thrust Washer not illustrated Distributes claming pressure of mounting nut evenly over V Belt Pulley cutting wheel The wheel that drives the V belt and the cutting wheel Cutting Wheel Can either be an abrasive wheel or a
4. the speed of the unit and may lead to serious injury 002BA061 KN A Warning Sparks from cutting metal can burn or cause clothing to catch fire Don t use a cut off machine on flammable ground Always direct sparks away from the operator or any flammable surroundings A Warning To reduce the risk of injury from fire do not cut into any pipe drum or other container without first insuring that it does not contain volatile or flammable substance Operating Instructions A Warning The wheel guard is adjustable It is extremely important that the wheel guard is in place and set to suit the type of work and your stance The guard should always be adjusted so that the user is not endangered by particles of the material being cut sparks or pieces of damaged wheels either directly or by ricochet Failure to follow this instruction could result in serious or fatal injury The ideal working speed of the cut off machine depends on many factors e g the material being cut the type and quality of the cutting wheel It is essential to determine the direction of the cut exactly before applying the abrasive wheel to the work Wheels are constructed for radial pressure only Lateral pressure must be avoided Check for cracks and make sure that no pieces have broken off from the wheel when it is stopped Check the wheel guard for cracks If you discover any cracks fit a new guard A Warning Hold the cut off ma
5. STIHL Cut off Machine Safety Manual Contents AN Main Parts of Cutquik Warning Definitions Because a cut off machine is a high speed cutting tool some special safety Safety Precautions precau tions must be observed to The Operator reduce the risk of personal injury The Cut off machine i The Use of the Cut off machine Careless or improper use may cause Maintenance Repair and Storing serious or even fatal injury Maintenance Chart To receive maximum performance and satisfaction from your STIHL cut off ma chine it is important that you read and understand the maintenance and safety precautions before using your cut off machine Please note that the illustrations on page 2 show the Cutquik TS 460 Since other types may feature different main parts it is important always to consult the owner s manual for the model concerned Contact your STIHL dealer or the STIHL distributor for your area if you do not understand any of the instructions in this manual Printed on chlorine free paper Printing inks contain vegetable oils paper is recyclable 2001 Andreas Stihl AG amp Co Waiblingen 0457 186 0121 M10 L8 T Printed in Germany wh WONOAA 15 STIHL Main Parts of Cutquik 1 Rear Handle 2 Air Filter 3 Wingnut of Filter Cover 4 Throttle Trigger Interlock 5 Throttle Trigger 6 Choke Lever 7 Slide control 8 Spark Plug Boot 9 Front Handle 10 Wheel Guard 11 Thrust Washer
6. cations Ensure proper ventilation when working in trenches or other confined areas 002BA060 KN Never use the cut off machine with one hand Your STIHL cut off machine is designed for hand held use or operation on a cut off machine cart Cutting with your cut off machine resting on the ground or other surface can cause excessive wear to the bracket designed to protect the bottom of the tank housing Loss of fuel and personal injury from fire may result Replace damaged or badly worn brackets immediately Grip Always hold the cut off machine firmly with both hands when the engine is running Place your left hand on front handle bar and your right hand on rear handle and throttle trigger Left handed users should follow this instruction too Wrap your fingers tightly around the handles keeping the handles cradled between your thumbs and forefingers Make sure your cut off machine handles and grip are in good condition and free of moisture pitch oil or grease 10 002BA059 KN Avoid standing in direct line with the wheel A Warning Take extreme care in wet and freezing weather rain snow ice Clear the area where you are working A Warning Avoid stumbling on obstacles and watch out for holes or ditches Be extremely cautious when working on slopes or uneven ground A Warning Never operate the cut off machine with the starting throttle lock engaged as this does not permit proper control of
7. chine steady Do not change the direction of the cut during the cut as this may produce a high torsional load on the abrasive wheel and may cause it to break or shatter To achieve a clean and efficient cut pull the abrasive wheel across the work or move it to and fro in the cutting direction Do not use force to push the abrasive wheel into the work Insert the wheel into the material only as deep as necessary to make the cut To reduce the amount of dust created do not cut all the way through stone and concrete materials leave a thin piece uncut For most such materials this piece can be easily broken afterwards Do not cock jam or wedge the wheel in the cut A Warning Do not use abrasive wheels for rough grinding Large bending stresses occur during such work and abrasive wheels may shatter or break and could cause serious or fatal injury If a cut off machine cart is used sweep debris from the path of the wheels as such may cause flexing of the abrasive wheel This would result in high frictional forces and thus greatly reduce the engine power available for the actual cutting work Always use the cart to cut in a straight line Wet cutting with abrasive wheels When cutting masonry with a water attachment 1 Make certain water does not flow on wheel that is not running since the wheel will absorb water and that will affect wheel balance 2 Shut water off before wheel stops so that excess water wi
8. diamond cutting wheel not illustrated Decompression Valve Makes starting easier Adjusting Lever of Wheel Guard To adjust the wheel guard in a way that the beam of sparks gets directed forward Muffler Attenuates exhaust noises and diverts exhaust gases in required direction Tensioning Nut For tensioning the V belt Starter Grip The grip of the pull starter which is the device to start the engine Fuel Filler Cap For closing the fuel tank Safety Precautions The use of any cut off ma chine may be hazardous Because a cut off machine is a high speed fast cutting power tool special safety precautions must be observed to reduce the risk of personal injury and fire It is important that you read fully under stand and observe the following safety precautions and warnings Read the Owner s Manual and the safety instructions periodically Careless or improper use of any cut off machine may cause serious or fatal injury Have your STIHL dealer show you how to operate your cut off machine Observe all applicable local safety regulations standards and ordinances A Warning Minors should never be allowed to use a cut off machine Bystanders especially children and animals should not be allowed in the area where a cut off machine is in use Never let the cut off machine run unattended Do not lend or rent your cut off machine without the Owner s Manual Be sure that anyone using your c
9. e contact is at the bottom of the wheel a cut off machine will try to pull away from the operator pull away If the contact is at the front of the wheel the wheel may attempt to climb the object being cut climbing If the wheel is severely pinched at the front the wheel may be instantly thrown up and back towards the operator with a great force ina rotational motion The greater the force generated the more difficult it will be for the operator to control the cut off machi ne Any of the reactive forces can in some circumstances cause the operator to lose control of a cut off machine allowing the rotating wheel to come into contact with the operator Severe personal injury or death can result Use only cutting attachment authorized by STIHL Never use chipped abrasive 12 wheels circular saw blades carbide tipped blades rescue blades or wood abrasive or toothed blades of any nature on a cut off machine The use of such wheels or blades will greatly increase the risk of loss of control and severe personal injury or death from reactive forces since the chipped section of an abrasive wheel or the teeth of a saw blade may catch in the material being cut and generate substantially greater reactive forces Cut off machines are designed for use with abrasive wheels in good condition only Machines designed for use with wood abrasive or other toothed blades use different types of guarding systems which provide the prot
10. ection neccessary for those types of blades Machines such as a cut off machine which are designed for use with abrasive abrasive wheels require a different guarding system which is not designed to provide protection against all dangers presented by circular saw blades carbide tipped blades rescue blades or wood abrasive or toothed blades of any nature A Warning To reduce the risk of injury from loss of control or from the shattering of an abrasive wheel 1 Hold the cut off machine firmly with both hands 2 Maintain good balance and footing at all times Never cut while standing on a ladder 3 Do not exceed the maximum operating speed marked on the wheel 4 Do not use a wheel that has been dropped 5 Never use circular saw blades carbide tipped blades rescue blades wood abrasive blades or toothed blades of any nature Their use increases the risk of injury from reactive forces blade contact and thrown tips 6 Do not cut any material for which the abrasive wheel is not authorized 7 Position the cut off machine in such a way that your body is clear of the abrasive attachment 8 Begin abrasive and continue at full throttle 9 Do not overreach 12 13 14 002BA062 KN Do not cut above shoulder height Use your cut off machine for abrasive only It is not designed for prying or shoveling away any objects Do not grind on side of the abrasive wheel Do not twist t
11. erly secure your cut off machine to prevent turnover fuel spillage and damage to the cut off machine Never transport with cutting wheel mounted A wheel damaged during transportation may shatter during operation and cause serious personal injury Preparation for the use of the cut off machine For assembly follow the procedure described at the appropriate section of your owner s manual Before operation of your cut off machine be sure the controls e g throttle trigger stop switch and the safety devices are working properly the carburetor idle and maximum speed are correctly adjusted and the wheel guard is in place and securely fastened to your unit All wheels should be carefully inspected for good condition before mounting Adjust the wheel guard so that sparks dust and cut material are deflected away from the operator and cannot reach flammable surroundings See operating instructions of your owner s manual Never operate a cut off machine that is damaged improperly adjusted or not completely and securely assembled Inspect for safety in operation Proper tension of the V belt is important In order to avoid a false setting the tensioning procedure must be followed as described in your Manual Always 8 make sure the hexagonal collar nuts for the cast arm are tightened securely Check V belt tension after one hour of operation and correct if necessary A Warning for TS 350 and TS 360 onl
12. fter finishing work Empty the fuel tank before storing for longer than a few days Fuel may only be stored in correctly labeled and approved containers Avoid direct skin contact and do not in hale the petrol vapours Keep the handles dry clean and free of oil and fuel Tighten all nuts bolts and screws except the carburetor adjustment screws after each use A Warning Never test the ignition system with ignition wire terminal removed from spark plug or with unseated spark plug since uncontained sparking may cause a fire A Warning To reduce the risk of fire and burn injury use only spark plugs authorized by STIHL Always press spark plug boot 13 snugly onto spark plug terminal of the proper size Note If terminal has detachable SAE adapter nut it must be attached A loose connection between spark plug terminal and ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire Keep spark plug clean and make sure ignition lead is in good condition A Warning Do not operate your cut off machine if the muffler is damaged missing or modi fied An improperly maintained muffler will increase the risk of fire and hearing loss Never touch a hot muffler or burn will result If your muffler was equipped with a spark arresting screen to reduce the risk of fire e g in the USA Canada and Australia never operate your cut off machine if the screen is missing o
13. hrust knock or drop the machine This can cause damage to the wheel Be especially alert for reactive forces when abrasive with the front of the wheel 15 Be alert to shifting of the work piece or anything that could cause the cut to close and pinch the wheel 16 Release the pressure on the cut off machine as you reach the end of the cut Too much pressure may cause the operator to lose control of the cut off machine when the abrasive wheel completes the cut The abrasive wheel may con tact the operator or strike some foreign object and shatter 17 Use extreme caution when re entering a cut and do not turn the wheel at an angle or push the wheel into the cut as this may result in a pinching of the wheel MAINTENANCE REPAIR AND STORING OF THE CUT OFF MACHINE Never operate a cut off machine that is damaged improperly adjusted or not completely or securely assembled Follow the maintenance and repair instructions in the appropriate section of your owner s manual Use only STIHL replacement parts for maintenance and repair Use of parts manufactured by others may cause serious or fatal injury A Warning Always stop the engine and make sure that the wheel is stopped before doing any maintenance or repair work or cleaning the cut off machine Do not attempt any maintenance or repair work not described in your owner s manual Have such work performed at your STIHL service shop only Clean grinding dust a
14. k of frost damage Failure to follow these directions may cause the wheel to shatter or crack in use causing serious or fatal injury A Warning Never use carbide tipped wood cutting or circular saw blades They can cause severe personal injury from reactive forces blade contact or thrown objects Your STIHL dealer stocks a range of special abrasive wheels for the many applications of the cut off machine A Warning Use of the wrong abrasive wheel or material for which it was not designed may cause that wheel to shatter causing serious or fatal injury Only use the abrasive wheel approved for the type of material to be cut There are different abrasive wheels each specially marked for example 1 Stone Also can be used for concrete masonary reinforced concrete and brick cutting 2 Steel Can be used for all ferrous metal cutting 3 Asphalt Also can be used for aggregate concrete cutting 4 Ductile iron Also can be used for certain grades of cast iron SG 17 24 bronze and copper cutting For cutting composite materials please ask your STIHL dealer Diamond abrasive wheels Diamond abrasive wheels have a much better cutting performance than the abrasive wheels The wheels are steel centered and diamond particles are imbedded in their cutting edges They can be used for concrete asphalt natural stone clay pipe brick and the like They are not suitable for cutting metal or other materials
15. ll be dissipated 3 Be certain water is applied to both sides of wheel since uneven distribution can cause one sided wear with possible wheel breakage 4 Use these wheels up the same day Do not store and reuse a wheel that has been used with water Important Adjustments At correct idle speed wheel should not turn For direction to adjust idle speed see the appropriate section of your owner s manual Do not use a cut off machine with incor rect idle speed adjustment The rotating wheel may cause injury Have your STIHL dealer check your cut off machine and make proper adjustments or repairs Never touch a rotating wheel with your hand or any part of your body Reactive forces A Warning Reactive forces may occur at any time the cutting wheel on at cut off machine is rotating If the wheel is slowed or stopped by frictional contact with any solid object or by a pinch reactive forces may occur instantly and with great force 11 These reactive forces may result in the operator losing control of the cut off machine which may in turn result in serious or fatal injury An understanding of the causes of these reactive forces may help you avoid loss of control Reactive forces are exerted in a direction opposite to the direction in which the wheel is moving at the point of contact or pinch Pull away climbing and rotational forces The most common reactive forces are pull away and climbing If th
16. not drop start This method is very dangerous because you may loose control of the cut off machine Place the cut off machine on firm ground or other solid surface in an open area Zz x wo O lt a Q Q Maintain a good balance and secure footing Be absolutely sure that the cutting wheel is clear of you and all other obstructions and objects including the ground because when the engine starts at starting throttle engine speed will be fast enough for the clutch to engage V belt pulley and turn the wheel Never attempt to start the cut off machine when the abrasive wheel is in a cut When you pull the starter grip don t wrap the starter rope around your hands Do not allow the grip to snap back but guide the starter rope slowly back to permit the rope to rewind properly Failure to follow this procedure may result in injuries to hand or fingers and may damage the starter mechanism Always stop the engine and be sure the wheel has stopped rotating before setting down the cut off machine Working Conditions Operate the cut off machine under good visibility and daylight conditions only A Warning Your cut off machine produces poisonous exhaust fumes as soon as the combustible engine is running These gases e g carbon monoxide may be colorless and odorless To reduce the risk of serious or fatal injury from breathing toxic fumes never run the cut off machine indoors or in poorly ventilated lo
17. r damaged Store spare wheels on a flat surface in a dry place preferably at a constant temperature where there is not risk of frost preferably at a constant temperature Store cut off machine in a high or locked place away from children Do not store a cut off machine with a wheel mounted on the machine 14 Maintenance Chart Please note Different models may have different parts and controls Every time after refuelling In the event of a malfunction If damaged After work or daily Monthly Before starting work Weekly As required Visual inspection condition absence of leaks x x Complete machine Clean x Throttle trigger throttle trigger interlock slide control Functional test Filter in fuel tank eles Replace Fuel tank Clean V belt Clean Replace Air filter prefilter auxiliary filter Clean Air filter all filter components Replace Cooling air intake ports Clean Cylinder fins Clean Inspect Spark arresting screen in the muffler Clean or replace Check idle speed Carburetor the cutting wheel must not run on Adjust idle speed Spark plug Adjust electrode gap Accessible nuts and bolts but not adjusting screws Retighten Check Rubber buffer AV element Have replaced by the STIHL customer service Cutting wheel Check Replace Support Bracket Rubber buffer Check Bottom side of unit Replace
18. ressly approved by STIHL for use with the specific STIHL cut off machine models are authorized Although certain unauthorized attach ments are useable with the STIHL powerhead their use may in fact be extremely dangerous A Warning Dust may collect on the powerhead especially around the carburetor and may collect gasoline resulting in danger of fire Clean dust from the powerhead regularly Abrasive wheels A Warning Before assembling your cutting wheel make sure that the maximum operating wheel speed is above or equal to the spindle speed of your cut off machine as provided in the Specifications of this manual Abrasive wheels for free hand cutting are subjected to particularly high bending and compressive stresses Warning Unauthorized wheels may shatter or break Use only STIHL wheels or other authorized wheels with approved RPM ratings Inspect the abrasive wheel frequently and replace immediately if the abrasive wheel is cracked or warped Cracked or warped wheels may shatter or break and cause serious personal injury Out of round or unbalanced abrasive wheels increase vibration and reduce the service life of the cut off machine Use STIHL wheels approved for this unit Abrasive wheels are heat sensitive Always store your cut off machine in a place where the cutting wheel is not exposed to direct sunlight or other sour ces of heat Store spare cutting wheels in a dry place where there is no ris
19. rotection complying with ANSI Z 87 1 Proper eye protection is a must To reduce the risk of injury to your eyes never operate a cut off machine Wear an approved safety hard hat to protect your head cut off machine noise may damage your hearing Always wear sound barriers ear plugs or ear mufflers to protect your hearing Regular users should have their hearing checked regularly A Warning Cutting masonry concrete and other materials may create dust Many types of dust are dangerous when breathed and can cause serious or fatal injury or illness such as respiratory disease or cancer If you are unfamiliar with the risks associated with the particular dust at issue review the material safety data sheet for the material being cut and or consult your employer the material manufacturer supplier govermental agencies such as OSHA and NIOSH and other sources on hazardous materials California and some other authorities for instance have published lists of sub stances known to cause cancer repro ductive toxicity etc Control dust at the source where possible In this regard use good work practices and follow the recommendations of the manufacturer supplier OSHA NIOSH and occupatio nal and trade associations A water attachment kit is available for your cut off machine and should be used for dust suppression when wet cutting is fea sible When dust can not be eliminated the operator and any bystanders should alway
20. s wear a respirator approved by NIOSH MSHA for the material being cut A Warning Cutting masonry concrete and other materials with silica in their composition may give off dust containing crystalline silica Silica is a basic component of sand quartz brick clay granite and numerous other minerals and rocks Repeated and or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory disease including silicosis In addition California and some other authorities have listed respirable crystalline silica as a sub stance known to cause cancer When cutting such materials always follow the respiratory precautions mentioned above A Warning Breathing asbestos dust is dangerous and can cause severe or fatal injury respiratory illness or cancer The use and disposal of asbestos containing products have been strictly regulated by OSHA and the Environmental Protection Agency Do not use your cutting off ma chine to cut or disturb asbestos asbestos containing products or pro ducts such as pipes which are wrapped or covered with asbestos insulation If you have any reason to believe that you might be cutting asbestos immediately contact your employer or a local OSHA representative THE CUT OFF MACHINE Parts of the cut off machine illustrations and definitions of the parts see pages 2and3 A Warning Never modify a cut off machine in any way Only attachments supplied by STIHL or exp
21. tely Proper Clothing Clothing must be sturdy and snug fitting but allow complete freedom of movement Avoid loose fitting jackets scarfs neckties jewelry flared or cuffed pants unconfined long hair or anything that could become caught on any obstacles or moving parts of the unit Wear over alls or long pants to protect your legs Do not wear shorts A Warning When cutting metal a cut off machine generates sparks which can ignite clothing Most fabrics used in clothing are flammable even flame retardant fabrics will ignite at higher temperatures To reduce the risk of burn injury STIHL recommends wearing clothing made of leather wool flame retardant treated cotton or a tightly woven heavier cotton such as denim Some flame retardant synthetic fabrics are also suitable but others such as polyester nylon rayon and acetate can melt during fire into a tar like matter that burns into the skin Keep clothing free of oil fuel grease and other flammable substances Protect your hands with gloves when handling the cut off machine Heavy duty nonslip gloves improve your grip and protect your hands Good footing is most important in cut off machine work Wear sturdy boots with nonslip soles Steel toed safety boots are recommended Warning Loose objects may be thrown toward the operator by the cutting tool unless wearing goggles ey or properly fitted safety glasses with adequate top and side p
22. ueling and move at least 10 feet 3 m from fueling spot before starting the engine Wipe off any spilled fuel and check for leakage A Warning If fuel gets spilled on clothes especially trousers it is very important to change clothes immediately Do not rely upon evaporation Flammable quantities of fuel may remain on clothes after a spill for longer than expected Cutting metal with cut off machine when clothes are wet or damp from gasoline is extremely dangerous as the operator s clothes might catch fire and cause serious or fatal injury Always make sure that the fuel cap is tightened securely Check for fuel leakage while refueling and during operation If a fuel leak is suspected do not start or run the engine until leak is fixed and spilled fuel has been wiped away A Warning Unit vibrations can cause an improperly tightened fuel cap to loosen or come off and spill quantities of fuel In order to reduce risk of fuel spillage and fire tighten fuel cap by hand A with as much force as possible The screw driver end of the STIHL combination wrench or other similar tool can be used as an aid in tightening slotted fuel caps Starting A Warning Your cut off machine is a one person tool Do not allow other persons to be near the cut off machine Start and operate your cut off machine without assistance For specific starting instruc tions see the appropriate section of your owners manual Do
23. ulate temperature produces numbness and burning sensations and cause nerve and circulation damage and tissue necrosis All factors which contri bute to whitefinger disease are not known but cold weather smoking and diseases or physical conditions that affect blood vessels and blood transport as well as high vibration levels and long periods of exposure to vibration are mentioned as factors in the development of whitefinger disease In order to reduce the risk of whitefinger disease and carpal tunnel syndrome please note the following Most STIHL cut off machine models are available with an anti vibration AV system designed to reduce the transmission of vibrations created by the engine to the operator s hands An AV system is recommended for those persons using cut off machines on a regular or sustained basis Wear gloves and keep your hands warm Keep the AV system well maintained A cut off machine with loose components or with damaged or worn AV buffers will tend to have higher vibration levels Maintain a firtm grip at all times but do not squeeze the handles with constant excessive pressures take frequent breaks All the above mentioned precautions do not guarantee that you will not sustain whitefinger disease or carpal tunnel syndrome Therefore continual and regular users should monitor closely the condition of their hands and fingers If any of the above symptoms appear seek medical advice immedia
24. ut off machine understands the information contained 4 in this manual Employers should estab lish a training program for operators of gasoline powered hand held portable cutt off machines to assure safe oper ation of these machines These safety precautions and warnings apply to the use of all STIHL Cutquiks e Different models may have different parts and controls See the appropriate section of your owner s manual for a description of the controls and function of the parts of your model cut off machine Safe use of a cut off machine involves the operator the cut off machine the use of the cut off machine THE OPERATOR Physical Condition You must be in good physical condition and mental health and not under the influence of any substance drugs alcohol etc which might impair vision dexterity or judgement Do not operate a cut off machine when you are fatigued Be alert if you get tired while operating your cut off machine take a break tired ness may result in loss of control Working with any cut off machine can be strenuous If you have any condition that might be aggravated by strenuous work check with your doctor before operating a cut off machine A Warning Prolonged use of cut off machines or other machines exposing the operator to vibrations may produce whitefinger disease Raynaud s phenomenon or carpal tunnel syndrome These conditions reduce the hand s ability to feel and reg
25. y The STIHL TS 350 and TS 360 Cutquik is supplied with a fuel filler elbow connector to facilitate easier refueling Always keep the connector and fuel filler cap tightened and properly sealed A loose or improperly seated connector or cap may vibrate loose during operation causing fuel spillage which may result in a fire which can cause serious or fatal injury Never operate the unit with a cracked broken or improperly seated or adjusted filler neck This could permit fuel leakage and lead to fire Do not fill tank above the threefourths level of the neck entry diameter into the tank Do not fill tank above the max line on the fuel filler elbow Overfilling reduces the room in the tank for fuel expansion and may lead to fuel spillage through the tank vent and risk of fire Fueling Your STIHL cut off machine uses an oil gasoline mixture for fuel see chapter Fuel of your owner s manual A Warning Gasoline is an extremely flammable fuel If spilled or ignited by a spark or other ignition source it can cause fire and serious burn injury or property damage Use extreme caution when handling gasoline or fuel mix Do not smoke or bring any fire or flame near the fuel Fueling Instructions Fuel your cut off machine in well ventila ted areas outdoors only Always shut off the engine and allow it to cool before refueling Relieve fuel tank pressure by loosening the fuel cap slowly Select bare ground for f
Download Pdf Manuals
Related Search