AV30MX-2 - Manual
Contents
1. 5 Technical Specifications Maximum Output 30Hz 20kHz Stereo Frequency Response 0 3 dB Bandwidth 3 0dB THD N Signal to noise ratio External Mute Slew Rate Input Sensitivity Standard Voltage Gain Input Impedance Unbalanced Sleep Idle Current Draw 1 8 Draw Class Input Connectors Output Connectors Power Supply Cooling Controls LED Indicators Construction Dimensions Height Width Depth Weight 30W 80 per channel 30W 40 per channel 30Hz 20kHz 30Hz 30kHz 0 196 at 1W gt 100dB 5 12VDC 30V ms 0 5V 3 dBV 28X 26 5dB 10k Ohms 0 005 0 01 0 15 Amps D 3 5mm Stereo Dual RCA Euro Block External In Line 48DVC Convection Cooling 2 Independent Level Controls Power Signal Present amp Clip Aluminum Chassis 1 25in 3 2cm 4 3bin 11 1cm 3 2in 8 1cm 0 37bs 0 16kg Stewart Audio reserves the rate to change features and specifications without notice 16 6 Warranty Information 6 1 Warranty Summary All Stewart Audio amplifiers and accessories unless excluded in this summary are covered by a 3 year limited warranty on parts and labor from the data of purchase In order to be eligible for warranty repairs the amplifiers and accessories must have been purchased through an authorized Stewart Audio dealer and submitted by the original pur chaser This warranty is only valid in the country in which the amplifier was purchased 6 1 1 Eligibility Requirements2. and Connectors 3 1 Operating Precautions 1 Before use your amplifier must be configure for proper operation including input and output wiring hookup Improper wiring can re sult in damage to equipment or potentially harm to the operator STEWART Consult section 2 for setup instructions 2 Tampering with the circuitry or making unauthorized changes is not only dangerous but may also violate local regulations 3 Use care when making connections between the amplifier and the input or output equipment Using equipment that is not capable of AV Series AV30MX 2 handling the output wattage may lead to permanent damage UL 2043 Plenum Rated a evel eve 1 NOTE Stewart Audio will not be held responsible for L Speaker o 3 inpute Eppur damage to your AV30MX 2 or connected equipment if Mute Pwr Input 1 the instructions in this manual are not followed Fe s 1 L CLIP R SIG Speaker Output Connector e Channel 1 Input 3 5mm e Remote Mute Q Power Indicator LED 3 Power Connector o Clip Indicator LED Left 4 Channel 2 Level Knob 10 Clip Indicator LED Right 5 Channel 1 Level Knob Signal Present Indicator LED O Channel 2 Input RCA 12 13 3 2 1 Indicators The AV30MX 2 has 4 rear panel LED indicators The first is the power indicator which will illuminate when power is supplied to the amplifier The next 2 LED indicators are the Clip indicators one for each output channel These lights will
3. connecting the triggering power source as the amplifier will not be muted if polarity is reversed 14 4 Troubleshooting Problem Power indicator does not turn on Procedure Check that the amplifier is plugged into a live outlet After you have ensured that It is not a power issue disconnect any speakers If the amplifier turns on after a few seconds delay then the problem is in the output connection Check wiring and speakers for short circuits Problem No output on one or both channels Power indicator is lit Procedure Check that level controls are not turned down Check that input and output connections are secure Ensure signal present LED is flashing to denote a signal If there is no signal detected check signal source and that level controls are set high enough Problem Amplifier overheats and or shuts off Procedure Review section 2 3 on proper cooling procedures Check the signal lights on the rear of the amplifier to see if the signal is over driving the signal light flashes red frequently Overdriving the amplifier for extended periods of time can cause a thermal shutdown Problem Output sound is distorted or cracking Procedure Check all cables for damage or loose connections and re duce the gain on the input signal at the mixer or preamp level Replace the cables and loudspeakers temporarily to see if this resolves the problem If problem still exists contact your Authorized Dealer for ser vice 15
4. indicate that one of the input signals is too hot and will sound distorted when amplified To fix this the gain should be reduced at the preamp or mixer level The final light is the signal present LED which will illuminate when signal is detected on either one of the input connection channels 3 2 2 Controls All AV30MX 2 controls are located on the rear of the unit There is no power switch so the AV30MX 2 will turn on whenever power is sup plied to it The AV30MX 2 s Signal Sense Technology SST will power up the amplifier from sleep when a signal is detected After 5 minutes without_an input signal the amplifier will go into sleep mode The rear panel contains a volume control for each input channel The amplifier is set to run off of a line level source and the level should be adjusted for optimum performance To adjust this knob you will need a small flat head screwdriver While a typical program source level is present spin the rotary knob as far clockwise as you can without hear ing distortion or without the Clip indicator illuminating If the signal is distorting and the knob is all the way counter clockwise adjust the gain down at the source level 3 2 3 Remote Mute The AV30MX 2 can be remotely muted when needed for such applica tions as muting during a fire alarm To do so 5 12VDC should be ap plied to the terminal block labeled MUTE on the rear of the AV30MX 2 Polarity should be observed when
5. D lt P3 i x 7 D gt lt 2 2 1 Universal Mount Installation The AV30MX 2 also has a universal bracket available which allows the unit to be mounted against a wall or under a table Two screws are included in the kit which will affix the bracket to the top or the side of the unit Once this is done two holes are available for mounting the unit where desired Part Number AV Bracket CAUTION Use only the screws provided in mounting brackets to the amplifier Do not overtighten 2 2 3 Product Dimensions A 4 35in 11 1cm STEWART 1 25in 3 2cm AV Series AV30MX 2 Front E 3 2in 8 1cm 1 25in 3 2cm Side 2 3 Proper Cooling Considerations Because the AV30MX 2 regulates its temperature using convection cooling and no fans the amplifier must be given adequate space to allow for proper airflow Do not stack the amplifiers on top of each other or mount it in a way that other equipment will block airflow through the case CAUTION Inadequate airflow to the amplifier can cause the amplifier to overheat and potentially become damaged in the process Be sure to provide plenty of air space to allow for convection cooling 2 4 Input Connections Your AV30MX 2 includes two independent stereo inputs which are then mixed into the final output Channel 1 will accept a stereo 3 5mm jack while Channel 2 will accept stereo RCA phono plugs Both inputs should be stereo unbalanced and line lev
6. E Any defective products received without an RA number will be returned to sender at their expense If Stewart Audio is unable to contact the sender in 14 days the mer chandise will be considered scrap and may be disposed of 6 2 2 Shipment Instructions If Stewart Audio requests that you ship the defective product back to their service center please refer to the guide below To ensure prompt warranty service be sure to follow all instructions 1 Return Authorization RA is required for product being sent to the factory for service 2 See packing instructions in section 6 2 3 3 Ship the defective product using a method which provides for or der tracking or order confirmation The service center is located at the following address Stewart Audio 14397 Cuesta Court Suite D1 Sonora CA 95370 4 Use a bold black marker and write the RA number on three sides of the box 5 Record the RMA number for future reference The RA number can be used to check the repair status 6 2 3 Packaging Instructions Should Stewart Audio request that you ship your product to their ser vice center these instructions must be followed in order to ensure safe delivery If they are not followed Stewart Audio assumes no responsi bility for damaged goods and or accessories that are sent with your unit 18 6 2 3 Packaging Instructions cont 1 Please write the RA number on three sides of the box Include the Stewart Audio RA number inside t
7. Stewart Audio warrants against all malfunctions which come as a result of component or manufacturer defect The amplifier is also covered from all failures which arise during the warranty period 3 years from date of purchase that are not a result of misuse The following actions will void your warranty e he power cord or AC plug has been damaged through misuse e he amplifier has been exposed to moisture or extreme tempera tures e he amplifier has been dropped items have been dropped on the amplifier or the enclosure has been damaged e The amplifier has been opened by the operator e The amplifier was improperly packaged when sending to the fac tory for repair resulting in damage e Any of the precautions or instructions found in this manual were not followed Damages resulting to the amplifier which are not covered under this warranty can be factory repaired at cost to the customer Use the con tact information below to initiate the repair process 6 2 Return Procedure This section includes the return procedures which must be followed in order to prevent processing delay or cost to the customer Please read the entire section before contacting Stewart Audio for returns 17 6 2 1 Return Authorization Number All returns to the factory for service must be accompanied by a Return Authorization RA number One can be obtained by contacting Stewart Audio at 209 588 8111 or via e mail at support stewartaudio com NOT
8. d to the customer 19 7 Accessories The following accessories are available from Stewart Audio for your amplifier All part numbers shown are Stewart Audio Part Numbers Mounting Brackets AV POLE Pole mount bracket for AV Series amplifiers AV BRACKET Universal mounting bracket for AV Series amplifiers Connection Adapters ADPT RCA Mono Female RCA to male Euroblock ADPT SUMRCA Stereo Female RCA to male Euroblock ADPT SUMS35 Stereo Female 3 5mm to male Euroblock Wall Plates WP RVC B Wallplate with 10k potentiometer and knob for re mote volume control Black WP RVC A Wallplate with 10k potentiometer and knob for re mote volume control Aluminum To purchase these accessories or to see the full Stewart Audio product lineup visit us at www stewartaudio com 20
9. el The AV3O0MX 2 does not include a pre amplifier Refer to the next section on the proper wiring for the 3 5mm and RCA inputs 2 4 1 Input Connection Diagrams Aa ih m d pics Shield Left Right Ground Shield Right Ground Shield 2 5 Output Connections Stewart Audio recommends using high quality heavy gauge speaker wire and connectors to send the output signal of your amplifier to the speakers Use the following table as a guideline when selecting your wire gauge Distance Wire Gauge Up to 25 ft 16 AWG 26 40 ft 14 AWG 41 60 ft 12 AWG Speaker leads connect by means of terminal block connectors supplied with the unit Strip speaker leads 1 4 and insert into connector ob serving proper polarity With a small flat blade screwdriver tighten the screw until the leads are held securely in place Inspect for possible shorts or broken wires 10 2 5 1 Speaker Configuration The AV30MX 2 s two stereo input channels are mixed and then sent out to the left and right speakers The expect speaker setup as a typical 8ohm or 4ohm configuration not to exceed 30W per side Once you have wired your terminal block connectors with the instruc tions in section 2 5 use the following diagram as a reference for con necting your speakers Output Connector Rear of AV30MX 2 Left Channel Right Channel ms H 4h h 11 3 Operation 3 2 Controls Indicators
10. eo amplifier with built in mixing capabilities e Optimized to drive 4 and 8 ohm loads e Music and fire alarm muting e Clean full range dynamic power e Signal Detect trigger for sleep amp wake up e Multiple mounting options e External inline power supply e Class D convection cooled 1 2 Using this Manual In order to obtain maximum performance from your AV Series Ampli fier please take time to read this brief owner s manual and carefully follow the guidelines for connection and operation This manual provides you with the information necessary to safely in stall and operate your new AV Series amplifier in the most common scenarios If you find yourself requiring additional assistance please feel free to contact your Authorized Dealer or you may contact us di rectly using the information provided on the back of this manual 2 Setup 2 1 Setup Precautions CAUTION Before installing your amplifier make sure that you have read the Important Safety Precautions at the be ginning of this manual 2 2 Amplifier Installation The AV30MX 2 incorporates a number of different mounting options in order to fit your installation needs 2 2 1 Pole Mounting The AV Series of amplifiers is Stewart Audio s first line of pole mountable amplifiers The AV30MX 2 has mount holes on both the top as well as the side of the unit which can be used with the AV Pole bracket available from Stewart Audio Part Number AV Pole
11. he box and a brief description of the problem 2 Do not ship any accessories manuals cords hardware etc with your unit These items are not needed to service your product Stewart Audio will not be held responsible for these items if they are returned with the amplifiers 3 When shipping your amplifier it is important that it has adequate protection We recommend you use the original packing material when returning the product for repair If you do not have the origi nal box see number 4 4 If you provide your own shipping pack the minimum recom mended requirements for materials are as follows a 275 P S l burst test Double Wall carton that allows for 2 inch solid Styrofoam on all six sides of unit or 3 inches of plastic bubble wrap on all six sides of unit b Securely seal the package with an adequate carton sealing tape c Do not use light boxes or peanuts NOTE Damage caused by poor packaging will not be covered under warranty 6 2 4 Estimate Approval An estimate for all non warranty repairs will be provided to the cus tomer once the unit has been shipped to the factory The customer is responsible to approve this estimate within 7 days If the repairs are not approved within 14 days Stewart Audio reserves the right to con sider the unit scrap and may discard it 6 2 5 Payment of Non Warranty Repairs Payment for non warranty repairs must be submitted to Stewart Audio before the product will be returne
12. ndicators and Connectors emn 13 3 2 1 Indicators ee 14 3 2 2 Controls eee 14 3 2 3 Remote Muting meemememmmHemmm 14 4 Troubleshooting 15 5 Technical Specifications 16 6 Warranty Information 8 17 6 1 Warranty Summary 17 6 1 1 Eligibility for Factory Repair mmm HHHmmmm 17 6 2 Return Procedure s nssnnnnnnnnaeassase 17 6 2 1 Return Authorization HH 18 6 2 2 Packaging Instructions 18 6 2 3 Shipping Instructions mM 18 6 2 4 Estimate Approval 19 6 2 5 Payment of Non Warranty Repair eme 19 7 Accessories eene nennen 20 xk x This amplifier proudly designed and manufactured in the USA 1 Welcome Congratulations on the purchase of your new Stewart Audio AV Series power amplifier This amplifier has been designed and built to provide you with years of high quality audio performance and trouble free op eration If after reading this manual you should have any questions con cerning amplifier installation and operation please contact your Author ized Stewart Dealer or you may contact us directly using the contact information provided on the back of this manual 1 1 Features Your Stewart Audio AV Series amplifier is the result of years of experience in the design and manufacture of quality amplifiers As such it provides a combination of performance and operational benefits that simply cannot be found in conventional amplifiers e Sub Compact 1 4 rack package e wo channel ster
13. o T EWART The Difference is Hear STEWARTAUDIO AV Series AV30MX 2 AV3O0MX 2 Owner s Manual October 2010 Important Safety Instructions Before using your Stewart Audio Inc Power Amplifier please read this Owner s Manual carefully to ensure optimum trouble free perform ance WARNING TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT EX POSE THIS AMPLIFIER TO RAIN OR MOISTURE DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE DO NOT OPEN THE CABINET REFER SERVICING TO QUALIFIED PERSONNEL ONLY CAUTION PN A CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lighting bolt within arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient mag nitude to constitute a risk of electrical shock to person The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instruction in the literature accompanying the appliance Important Safety Instruction Please Read Prior to Product Installation 1 Installation should be performed by a trained and licensed professional to insure safe and lasting operation 2 All of the safety and operating instructions should be read before
14. or a long period of time the power cord should be unplugged form the outlet 10 Damaged Amplifiers requiring service should be repaired by a qualified service technician when The power cord or AC plug has been damaged Objects have fallen or liquid has spilled into the unit The amplifier has been exposed to rain or other moisture The amplifier does not appear to operate normally or exhibits a marked change in performance e The amplifier has been dropped or the enclosure damaged oocoo 11 The user should not attempt to service the amplifier beyond that de scribed in the operating instructions All other servicing should be referred to qualified service personnel Table of Contents Important Safety Instructions ee mee 2 Tabl of COITU DB esetsi penes Sprite nag UiRegi Uu aiana a 4 1 Welcome serene tne eens nt priies ghe Essi PUR RM HUE 5 ES Ge en end E 5 1 2 Using this Manual mmm 5 2 Setup eene nennen nennen 6 2 1 Setup Precautions s eisintac Up nieht ende Ub ipti laa 6 2 2 Amplifier Installation mmn 6 2 2 1 Pole Mount Installation eetere 6 2 2 2 Universal Mount Installation enn 7 2 2 3 Product Dimensions eee 8 2 3 Proper Cooling Considerations Hee mm 8 2 4 Input Connections HM 9 2 4 1 Balanced Input Connections eene 9 2 4 2 Unbalanced Input Connections me 10 2 5 Output Connections eene 11 3 Operation eee eene 12 3 1 Operation Precautions eee 12 3 2 Controls I
15. the am plifier is installed or operated Retain these instructions for future refer ence All instructions should be followed all warnings on the amplifier and in the operating instructions should be adhered to 3 The amplifier should be situated so that its location and position does not interfere with its proper ventilation For example the amplifier must not be placed on a rug bed sofa or similar surface that impedes airflow across the chassis Airflow through the ventilation openings should be unobstructed 4 This amplifier should not be used near water for example near a bathtub in a wet basement near a swimming pool etc This amplifier is intended to be operated in a controlled indoor environment 5 Do not place the amplifier near heat sources such as radiators heat regis ters stoves or other appliances that produce heat 6 The amplifier should only be connected to 120 VAC 60 Hz power supply Do not defeat the ground or polarization of the power plug 7 Route power cord and other cables so that they are not likely to be walked on tripped over or stressed Pay particular attention to condition of cords and cables at plugs and at the point where they exit the ampli fier To prevent risk of fire or injury damaged cords and cables should be replaced immediately 8 Clean the amplifier with a clean damp cloth Do not use solvents or abra sive cleaners Never pour any liquid on the amplifier 9 When left unused f
Download Pdf Manuals
Related Search