Home

NETWORK ADAPTER

image

Contents

1. Card ST100S ST100SW ST100SLP Instruction Guide The Professionals Source For Hard to Find Computer Parts FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help a Table of Contents Introduction siie e sie ie cls teisse taste BU Riese Be Meee WINE Hae 0 si 2 Installation seoran nam nedmes eases nivel ing laeks Mew Reade 3 Connecting Your Card to Your Network 0 cece cece cece eee e
2. cable e If you are connecting your computer to a hub or switch you should use a straight through cable e If you are connecting your computer to the Internet via a DSL or cable modem you should use the cable recommended by the modem manufacturer Installing the Drivers NOTE Windows XP will automatically detect the new hardware and install the necessary drivers without any user input The following are installation instructions for Windows OS only If you are using Linux Netware or any other supported environment consult the driver installation instructions available in text form on the driver disk The most recent drivers for your Ethernet adapter are available as a free download from our website Visit www startech com and click on the Downloads link for information Depending on your version of Windows and the configuration of your system the instructions that appear on your screen might not be identical to the instructions below Windows 2000 ME 98 1 Windows will automatically detect the new hardware Click Next 2 Choose Driver from disk provided by hardware manufacturer 3 Insertthe driver disk into your disk drive and specify the following path where A is the location of your driver disk e Windows 2000 A XWIN2000 e Windows ME A WINME e Windows 98 A XWIN98 4 You may be reguired to insert your Windows installation disk Follow the remaining prompts and reboot your computer when prompted g
3. install the card System Requirements e An IBM compatible notebook computer with a Pentium processor e An open PCI slot One of the following operating environments Windows XP ME 2000 98 95 Windows NT Linux NetWare 3 x 4 x Lan Manager TCP IP software e ST100SW ONLY To take advantage of the Wake On Lan feature your motherboard must be equipped with ACPI Wake On Lan capabilites Consult your motherboard user guide or contact the manufacturer for information WARNING PCI cards like all computer equipment can be severely damaged by static electricity Be sure that you are properly grounded before opening your computer case or touching your PCI card StarTech com recommends that you wear an anti static strap when installing any computer component If an anti static strap is unavailable discharge yourself of any static electricity build up by touching a large grounded metal surface such as the computer case for several seconds Also be careful to handle the PCI card by its edges and not the gold connectors SS Contents This package should contain e 1x PCI Ethernet Adapter card e 1x driver disk Installation This section will guide you through the installation of your card and the related software Please read through the instructions carefully and complete each step in the order listed Installing the Card 1 2 Make sure that your system is unplugged and you are grounded Remove the cover of your system
4. Start then click My Network Places 2 Click View Network Connections in the Network Tasks box 3 Right click on Local Area Connection and choose Properties Windows 2000 1 Click on Start then Settings then Network and Dialup Connections 2 Double click Local Area Connections and click the Properties button Windows Me 98 95 1 Click on Start then Settings then Control Panel 2 Double click on Network NOTE If you need to add any of the following components check your Windows documentation for details Make sure all your computers are on the same workgroup To be able to communicate properly with each other each computer must be located on the same workgroup Each computer within a workgroup must have a unique name To ensure compatiblility between each version of Windows keep your computer names under 13 characters long To view add or edit your computer s name do the following HEI g Windows XP 1 Click Start and then Control Panel 2 Double click System then click on the computer name tab Windows 2000 1 Click on Start then Settings then Control Panel 2 Double click on System 3 Click on the Network Identification tab Windows Me 98 95 1 Click Start then Settings then Control Panel 2 Double click Network then click the Identification tab Make Sure Your Sharing is Set Up Properly 1 Go to your network dialog box using the procedure explained under Make sure your computers are co
5. e installation process m 6 Monitoring Your Card The LEDs on the front of the card are the best indication of the card s activity 10M Link Activity Yellow On Card is in 10Mbits sec mode Blinking Network activity 100M Link Activity Green On Card is in 100Mbits sec mode Blinking Network activity If neither Link Activity LED is lit there is a connection error Make sure that all devices are turned on and that the network cable is properly connected at both ends Also make sure that your network cables comply with EIA TIA 568 and Category 5 specifications If problems persist power down all devices and disconnect all plugs Wait at least ten seconds then plug the devices back in and power them up S S Tips for Setting Up Your Network For information and help on setting up your network please consult the manufacturer of your operating system The following is for tips and troubleshooting purposes only and is intended for Microsoft users on a local area network Make sure your computers are configured properly For your convenience you should configure each of your computers so that they can see each other and share devices and files To do this you have to make sure that the following have been installed on your computers e Client for Microsoft Networks e TCP IP Internet Protocol e File and Print Sharing These clients protocols and services can be found in the following locations Windows XP 1 Click on
6. ee 4 Installing the Drivers 0 ccc cece ccc cence nent eee isme 5 Monitoring Your Card cece ccc cect eee eee e nee e eee eeeeees 6 Tips for Setting Up Your Network evvrrrnnneerennnee 7 Technical Support six sais sac Sete eae eee We WN LEN ow ete cae ete 9 Warranty Information x veeerrreneeereereenneeeenneee 9 I Y Y 7m 7m mn I Introduction Thank you for purchasing a StarTech com10 100 Mbits sec PCI Ethernet card This reliable high speed network card lets you connect your computer to your Ethernet LAN and experience super fast transfer speeds of up to 100Mbits sec Full duplex support means that the card can simultaneously transmit and receive information at these high speeds The card is a snap to install and set up and is fully Plug and Play compatible in a wide range of operating environments Features Complies with 10BaseT Ethernet and 100BaseTX Fast Ethernet standards e Capable of full and half duplex communications e Complies with Plug and Play specifications e Auto negotiation function determines the optimal transmission rate Supports 32 bit PCI Bus Master for high performance and low processor utilization Backed by StarTech com s lifetime warranty Before You Begin To ensure a quick and easy card installation please read through this section carefully before attempting to
7. gainst defects in materials and workmanship for the periods noted below following the initial date of purchase During this period the products may be returned for repair or replacement with equivalent products at our discretion The warranty covers parts and labor costs only StarTech com does not warrant its products from defects or damages arising from misuse abuse alteration or normal wear and tear Limitation of Liability In no event shall the liability to StarTech com Ltd or its officers directors employees or agents for any damages whether direct or indirect special punitive incidental consequential or otherwise loss of profits loss of business or any pecuniary loss arising out of related to the use of the product exceed the actual price paid for the product Some states do not allow the exclusion or limitation of incidental or consequential damages If such laws apply the limitations or exclusions contained in this statement may not apply to you Revised April 22 2003
8. nfigured properly 2 Click on File and Print Sharing 3 Choose whether you want to install one both or neither of these options Click OK 4 Decide what files or folders you want to share You can call up sharing options b right clicking on a file or folder and choose Sharing Windows 2000 Me 98 95 or Sharing and Security Windows XP NOTE If you are having any difficulties setting up or using your network please contact your operating system vendor Technical Support The following technical resources are available for this StarTech com product On line help We are constantly adding new information to the Tech Support section of our web site To access this page click the Tech Support link on our homepage www startech com In the tech support section there are a number of options that can provide assistance with this card Knowledge Base This tool allows you to search for answers to common issues using key words that describe the product and your issue FAQ This tool provides quick answers to the top questions asked by our customers Downloads This selection takes you to our driver download page where you can find the latest drivers for this product Call StarTech com tech support for help 1 519 455 4931 Support hours Monday to Friday 9 00AM to 5 00PM EST except holidays Warranty Information This product is backed by a one year warranty In addition StarTech com warrants its products a
9. see your computer s user manual for details if necessary and gently turn your computer onto its side Locate an empty PCI slot usually white in colour and remove the metal plate that covers the rear bracket You may need a Phillips screwdriver to perform this step Hang on to the screw You will need it to secure the card later Gently insert the card into the empty slot making sure it is firmly seated Secure the card in place using the screw you removed in Step 3 ST100SW ONLY Connect the Wake On LAN WOL connector to the WOL plug on your motherboard Consult your motherboard user guide for information if necessary Put the computer case back on Nd aaa Connecting Your Card to Your Network Depending on how you are planning on using the card the device you are connecting it to and the type of cable you need may differ To take advantage of the NIC s 100 Mbits sec capacity it is recommended that you always use at least Category 5 Ethernet cable If you are unsure of the type of cable required for your device consult your device manufacturer NOTE StarTech com carries a wide range of Ethernet cables in various colors and lengths For more information on these products as well as tips and ideas for setting up and running your network visit http www startech com and click on the Networking tab near the top of the screen e If you are connecting your computer directly to another computer you need to use a crossover
10. t Windows 95 1 2 Windows will automatically detect the new hardware Click Next Select Driver from disk provided by hardware manufacturer Insert the driver disk into your disk drive and specify the following path where A is the location of your driver disk e A WIN95 Windows NT 4 0 1 2 From your Control Panel double click on the Network icon Choose Add Adapters and select lt Other gt Reguires disk from manufacturer Insert the driver disk into your disk drive and specify the following path where A is the location of your driver disk e ANWINNT4 The Select line speed dialog box will appear The default is Auto where the adapter will auto detect the line speed You can choose to set the value to 10 half or full duplex or 100 half or full duplex Mbps if you so choose The Input Ethernet ID dialog box will appear This option is only reguired if you have more than one Fast Ethernet adapter on the computer Choose Skip if you have only one adapter installed If you are adding more than one Fast Ethernet Adapters consult the Msnt txt file located in the Txt Ms folder for additional instructions The Bus Location dialog box will appear If your machine contains more than one hardware bus please select the Bus Type and Bus Number where the network adapter is installed Follow any additional on screen prompts and reboot your computer to complete th

Download Pdf Manuals

image

Related Search

Related Contents

Panasonic CQ-C9800W CD Player  DVR104 DVR108 DVR116  Samsung GT-E2232 راهنمای محصول  NOVA-9452 SBC User Manual  TLP-S200  Consulter  APart PA19 mounting kit  ELM3311 ELM3711  user guide (right way round).p65    

Copyright © All rights reserved.
Failed to retrieve file