RS-422/485 DB9 CardBus Adapter
Contents
1. as a PCI Communications Port Double click on the COM Port you wish to configure select Data rate click on Detect Crystal Frequency then OK Ax General Settings FIFOs Data rate Driver 160952 E r laput Clock Crystal Frequency MHz Delect Crystal FPguency Woking E r Baud rate configuration options IV Use default baud rate Windows 98 ME 1 As mentioned on page 2 move the HSPD switch to the down position 2 Right click on My Computer and select Properties 3 Choose Device Manager and double click on Ports 4 You will notice the added port listed as a PCI Communications Port Double click on the COM Port you wish to configure select Data rate and put a checkmark next to Detect Crystal Frequency by clicking in the box provided Click on OK to save this setting Application Wiring RS 485 Transmitter is controlled by ATTA Hardware Please note CB1S485 supports 2 wite twisted pair cable optional auto echo mode operation When enabled data sent to the connected RS 485 transmitter is simultaneously sent to the receiver The current application can then CB1S485 Bud use the echoed data to check iid for data collisions RXD 485 RXD 485 RXD 485 RXD 485 Instruction Manual RS 422 Transmitter buffer is always enabled 4 wire Twisted Pair Cable TXD TXD RXD 485 RXD 485 Please note CB1S485 supports 4 wire RS 422 mode which requires cr2. RS 422 485 DB9 CardBus Adapter 1 Port RS 422 485 DB9 CardBus Adapter CBIS485 StarTech com Making hard to find easy FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Use of Trademarks Registered Trademarks and other Protected Names and Symbols This manual may make reference to trademarks registered trademarks and other protected names and or symbols of third party companies not related in any way to S
3. chnical Support ur Trece nme wie dae Gute ete a 9 Warranty Information lesse hm nn 9 a Introduction Thank you for purchasing a StarTech com CardBus RS 422 485 Card This high performance RS 422 485 card works well with two wire with Auto Transceiver Turn Around feature ATTA and four wire configurations and offers 16C950 compliant UARTS for broad serial device compatibility Features e RS 485 mode supports Auto Transceiver Turn Around ATTA e 128 byte deep FIFO per transmitter and receiver UART is 16C950 compatible to work with most serial devices Supports the RS 485 and RS 422 serial interfaces Maximum data transfer rate up to 921kbps Before you begin System requirements A host computer with an available CardBus Slot Please note that CB1394B3 can be used on a desktop computer using a PCMCIA to PCI Adapter Card For more information please see Accessory Products from StarTech com Operating System Windows 98 ME NT 2000 XP 2003 VISTA LINUX Package contents This package should contain 1xSerial PCMCIA Card e 1x Breakout Cable e 1 x Instruction Manual e 1 x Driver CD Hardware Guide UART Input Clock Speed Selector Instruction Manual Switch Switch Name Positions Oleg zie UART Input Clock Speed 1 8432MHZ Up Maximum baud rate is 115 2Kbps UART Input Clock HSPD HSPD Speed 14 7456MHZ Switch Down Maximum baud rate i
4. et through our locations in the United States Canada the United Kingdom and Taiwan Visit www startech com for complete information about all our products and to access exclusive interactive tools such as the Parts Finder and the KVM Reference Guide StarTech com makes it easy to complete almost any IT solution Find out for yourself why our products lead the industry in performance support and value 14 August 2007 Rev A
5. ion This product is backed by a lifetime warranty In addition StarTech com warrants its products against defects in materials and workmanship for the periods noted following the initial date of purchase During this period the products may be returned for repair or replacement with equivalent products at our discretion The warranty covers parts and labor costs only StarTech com does not warrant its products from defects or damages arising from misuse abuse alteration or normal wear and tear Limitation of Liability In no event shall the liability of StarTech com Ltd and StarTech com USA LLP or their officers directors employees or agents for any damages whether direct or indirect special punitive incidental consequential or otherwise loss of profits loss of business or any pecuniary loss arising out of or related to the use of the product exceed the actual price paid for the product Some states do not allow the exclusion or limitation of incidental or consequential damages If such laws apply the limitations or exclusions contained in this statement may not apply to you 9 About StarTech com StarTech com is The Professionals Source for Hard to Find Computer Parts Since 1985 we have been providing IT professionals with the quality products they need to complete their solutions We offer an unmatched selection of computer parts cables server management solutions and A V products and serve a worldwide mark
6. le click on the executable file Follow the prompts to complete installation RS 485 2 wire mode To enable CB1S485 to operate in RS 485 2 wire mode 1 Right click on My Computer If you are using Windows 98 ME select Properties If you are using Windows 2000 XP select Manage 2 Choose Device Manager and double click on Ports 3 You will notice the added ports listed as a PCI Communications Port Double click on the COM Port you wish to configure and select Settings Windows 2000 XP 1 In the PCI Communications Port Properties window click on the Settings tab 2 Under Hardware config select RS422 485 and change the RS485 buffer enable value to Active Low using the dropdown box provided Click OK to save and exit Pct Communications Port COM3 Properties iy x General Settings FIFOs Date rate Driver Power Management 16052 E Windows 98 ME 1 In the PCI Communications Port Properties window click on the Settings tab 2 Change the DTR function to RS485 Buf_En Active low using the dropdown box provided Baud Rate By default CB18485 is set to a baud rate of 115 2Kbps maximum To increase the baud rate to 921 6Kbps maximum Windows 2000 XP 1 As mentioned on page 2 move the HSPD switch to the down position 5 Instruction Manual 2 Right click on My Computer and select Manage 3 Choose Device Manager and double click on Ports 4 You will notice the added port listed
7. le to remove all possible static discharge potential from A any objects that the ExpressCard may come in contact with before installation This can be accomplished by touching a grounded metal object prior to insertion 1 With the notebook PC powered on and fully booted insert the PCMCIA Card into an available CardBus slot on the host computer 2 Connect the 15 pin connector of the cable to your PC card then connect the DB9 connector to your serial device 3 The Add New Hardware Wizard will launch and will guide you through the driver installation process Driver Installation Windows 98 ME 2000 XP 2003 The necessary driver files are in ZIP format e g V6515 RS422 485 ZIP and are located in E IO OXFORD RS422_485 where E denotes the CD DVD ROM drive Please copy the file to your local hard drive presumably C and unzip it before proceeding with installation 1 When the Found New Hardware Wizard appears click Next to continue 2 Select Install from a list or specific location advanced and ED E click Next Pte Ox FORD O R8422 485 3 Select Include this location in the search and click Browse to specify the driver s location 4 Click Next to continue then click on Finish to complete installation Windows NT Because Windows NT does not support plug and play you will need to locate the Install Serial exe file in the EMOYOXFORDWVnNTA folder where E designates the location of the CD DVD ROM drive and doub
8. oss over twisted pair cable CB1S485 also provides two handshaking signals RTS RTS and CTS CTS to perform hardware flow control which requires the following wiring scheme RS422 CB1S485 Device Instruction Manual Accessory Products from StarTech com Contact your local StarTech com dealer or visit www startech com for cables or other accessories that will help you get the best performance out of your new product MC3MF 3 ft AT Modem Cable DB9F DB25M MC6MF 6 ft AT Modem Cable male to female MXT100 6 ft 9 pin Straight Through Cable male to female SCNM925FM 10 ft Cross Wired Serial Null Modem Cable DB9F to DB25M SCNM9FF 2 10 ft Cross Wired Serial Null Modem Cable DB9 F F PCI2PCMCIA1 1 Port CardBus PCMCIA to PCI Adapter Card PCI2PCMCIA1E 1 Port CardBus PCMCIA to PCI Adapter Specifications Regulatory Certifications ROHS FCC CE Bus Type 32 bit CardBus Type ll Slot Connectors 1 X DB9 MALE CONNECTOR Maximum Data Transfer Rate 921 kbps OS Support Windows 98 ME NT 2000 XP 2003 VISTA LINUX Bits Data Framing Support 5 6 7 8 9 Technical Support StarTech com s lifetime technical support is an integral part of our commitment to provide industry leading solutions If you ever need help with your product visit www startech com support and access our comprehensive selection of online tools documentation and downloads Warranty Informat
9. s 926 1Kbps default Default Setti etting requires adjustment from Windows Device Manager RS 422 485 Mode Selector No Echo No Loop Echo Switch Loop Switch Mode and eae Spi Termination Resistor a id Setting Up 2 wire RS 485 mode default Note 422 Down 4 wire RS 422 mode 422 485 Transmitting data will Mode Switch Up be echoed back NECH 5 Please note own No echo data 1 Please note that if the mode were set default at 422 mode the other settings RTS will be NECH and NLP settings will take no effect Up connected to CTS NLP 2 Echo mode is used to detect data collisions Down RTS and CTS If the echoed data was not equal to the default operate normally transmitted data then data collisions are occurring E 5 Hardware Guide Cont d Terminator Settings Switch Switch Termination Resistor Name Settings Setting Up TXD Terminator Default Disabled TAB Down TXD Terminator Enabled Up RXD Terminator RXD Disabled Terminator Down RXD Terminator Enable Disable Default Enabled Switches Up RTS Terminator Default Disabled RTS Down RTS Terminator Enabled Up CTS Terminator CTS Disabled Down CTS Terminator Default Enabled DB9 Connector Pinout 9 Pins Signal 1 TXD DATA 1 5 2 TXD DATA 3 RXD 4 RXD 0000 6 RTS 7 RTS 8 CTS 6 9 9 CTS a Installation Caution It is advisab
10. tarTech com Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech com or an endorsement of the product s to which this manual applies by the third party company in question Regardless of any direct acknowledgement elsewhere in the body of this document StarTech com hereby acknowledges that all trademarks registered trademarks service marks and other protected names and or symbols contained in this manual and related documents are the property of their respective holders Table of Contents Introduction ete a Lem RUE Scene MEE NEIN 1 FO AtUIES ees ots aee a emer ain AER RR UAE ah 1 System Requirements 0 0 0 cece eee ees 1 Package Contents 0 cece ett 1 Hardware Guide nico caso a sa era ase nine Seales Sash aor eae ae 2 UART Input Clock Speed Selector 00 0c eee eee 2 RS 422 485 Mode Selector 0 0 cece eee o 2 Terminator Settings iliis een 3 DB9 Connector Pinout 00 00 eee 3 Installation 62 i cia rc I Ru ee ee eee eke 4 Driver Installation 0 0 00000 eee 4 RS 485 2 wire mode 20 e cece eens 5 Baud Rate a mu Ra A IM GR Rae heehee te 5 Application Wiring ssleee RIAM 6 RS 485 ul ena LESER WR EA ect E AR T b eI 6 la D rM 7 Accessory Products from StarTech com sleuslss 8 Specifications 5 522 a DAI acta Sie Due ei EE 9 Te
Download Pdf Manuals
Related Search