Reference Guide
Contents
1. General Power requirements 220 V 240 V AC 50 Hz 60 Hz Power consumption On 55 W Control for HDMI is off Standby mode 0 5 W or less BLUETOOTH Standby mode 0 5 W or less Dimensions approx w h d 1 080 mm x 109 mm x 110 mm without grille frame without stands 1 080 mm x 109 mm x 129 mm with grille frame without stands 1 080 mm x 129 mm x 138 mm with grille frame with stands 1 080 mm x 129 mm x 130 mm without grille frame with stands Mass approx 7 9 kg with grille frame with stands Subwoofer SA WST7 POWER OUTPUT reference 100 W per channel at 4 ohms 100 Hz Speaker system Subwoofer Passive radiator type Speaker 180 mm cone type 200 mm x 300 mm cone type Passive radiator Rated impedance 4 ohms Power requirements 220 V 240 V AC 50 Hz 60 Hz Power consumption On 30 W Standby mode 0 5 W or less Dimensions approx 241 mm x 391 mm x 411 mm w h d Mass approx 11 2 kg Wireless transceiver EZW RT50 Communication System Wireless Sound Specification version 1 0 Frequency band 5 725 GHz 5 875 GHz Power requirements DC 3 3 V 300 mA Modulation method DSSS Dimensions approx 30 mm x 9 mm x 60 mm w h d Mass approx 109 continued ss 1568 Digital audio input formats supported by the system DTS HD Master Audio Dolby Digital Plus DTS HD High Resolution Audio Dolby TrueHD DTS HD Low Bit Rate DTS Linear PCM 2ch 48 kHz or less DTS 96 242. Adjusting the settings in the Operating Instructions No sound or only a very low level sound of the equipment connected to the Bar Speaker is heard from the Bar Speaker gt Press VOL and check the volume level refer to Parts and controls in the Operating Instructions gt Press MUTING or VOL to cancel the muting function refer to Parts and controls in the Operating Instructions gt Make sure the input source is selected correctly You should try other input sources by pressing the INPUT button several times refer to Listening to the audio in the Operating Instructions gt Check that the input source is correctly selected gt Check that all the cables and cords of the system and the connected equipment are fully inserted No sound or only a very low level sound is heard from the subwoofer gt Turn up the subwoofer volume by pressing the SW VOL button refer to Parts and controls in the Operating Instructions gt Make sure that the 1 0 indicator on the subwoofer is lit in green If not refer to No sound is output from the subwoofer in WIRELESS SOUND page 13 1268 gt Asubwoofer is for reproducing bass sound In the case of input sources that contain very little bass sound components i e a TV broadcast the sound from the subwoofer may be difficult to hear gt When you play content compatible with copyright protection technology HDCP it i
3. If the TV is compatible with the Audio Return Channel ARC technology an HDMI cable connection also sends a digital audio signal from the TV to the system You do not need to make a separate audio connection for listening to TV sound from the system One Touch Play When you play the equipment connected to the system with an HDMI cable the connected TV is turned on automatically and the input signal of the system is switched to the appropriate HDMI input Notes The above features may not operate with certain equipment e Depending on the settings of the connected equipment the Control for HDMI function may not work correctly Refer to the operating instructions of the equipment Using BRAVIA Sync features The original Sony functions listed below can also be used with products that are compatible with BRAVIA Sync Power save If a BRAVIA Sync compatible TV is connected to the system the power consumption is reduced in standby mode by stopping HDMI signal transmission when TV is turned off Notes on HDMI connections e Use a High Speed HDMI cable If you use a Standard HDMI cable 1080p Deep Color 3D and 4K images may not be displayed properly e Use an HDMI authorized cable Use a Sony High Speed HDMI cable with Cable Type Logo e We do not recommend using an HDMI DVI conversion cable e Check the setup of the connected equipment if an image is poor or the sound does not come out of the equipment con
4. going to use the system for a long time be sure to disconnect the system from the wall outlet mains To disconnect the AC power cord mains lead grasp the plug itself never pull the cord One blade of the plug is wider than the other for the purpose of safety and will fit into the wall outlet mains only one way If you are unable to insert the plug fully into the outlet contact your dealer e AC power cord mains lead must be changed only at the qualified service shop On heat buildup Although the system heats up during operation this is not a malfunction If you continuously use this system at a large volume the system temperature ofthe back and bottom rises considerably To avoid burning yourself do not touch the system On placement Place the system in a location with adequate ventilation to prevent heat buildup and prolong the life ofthe system e Do not place the system near heat sources or in a place subject to direct sunlight excessive dust or mechanical shock e Do not place anything at the rear of the Bar Speaker and subwoofer that might block the ventilation holes and cause malfunctions elf the system is being used in combination with a TV VCR or tape deck noise may result and picture quality may suffer In this case place the system away from the TV VCR or tape deck e Use caution when placing the system on surfaces that have been specially treated with wax oil polish etc as staining or dis
5. occur or the audio may cut off depending on the BLUETOOTH device connected with this system the communications environment or surrounding conditions Installing the Bar Speaker on a wall You can install the Bar Speaker on the wall e Use screws that are suitable for the wall material and strength As a plaster board wall is especially fragile attach the screws securely to a wall beam Install the Bar Speaker on a vertical and flat reinforced area of the wall e Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation eSony is not responsible for accidents or damage caused by improper installation insufficient wall strength improper screw installation or natural calamity etc 1 Prepare screws not supplied that are suitable for the holes on the back of the Bar Speaker fmf 4mm c More than 30 mm 4 6 mm AT 10 mm Hole on the back of the Bar Speaker continued ss 768 2 Fasten the screws to the wall The screws should protrude 8to 9 mm Center ofthe Bar Speaker 365 mm left 310 mm right 8 to 9 mm 3 Hang the Bar Speaker onto the screws Align the holes on the back of the Bar Speaker to the screws then hang the Bar Speaker onto the 2 screws E Enabling the IR repeater function when you cannot control the TV When the Bar Speaker is placed in front of a TV the TV may not be controlled with
6. of them makes no difference Output HDMI TV OUT ARC BLUETOOTH section Communication system BLUETOOTH Specification version 3 0 Output BLUETOOTH Specification Power Class 2 Maximum communication range Line of sight approx 10 m Maximum number of devices to be registered 9 devices Frequency band 2 4 GHz band 2 4000 GHz 2 4835 GHz Modulation method FHSS Freq Hopping Spread Spectrum Compatible BLUETOOTH profiles A2DP Advanced Audio Distribution Profile AVRCP 1 3 Audio Video Remote Control Profile Supported Codecs SBC AACS aptX Transmission range A2DP 20 Hz 20 000 Hz Sampling frequency 44 1 kHz 1 The actual range will vary depending on factors such as obstacles between devices magnetic fields around a microwave oven static electricity cordless phone reception sensitivity operating system software application etc 2 BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices 3 Codec Audio signal compression and conversion format 4 Subband Codec 5 Advanced Audio Coding Front L Front R speaker blocks Speaker system 2 way speaker system Acoustic suspension Speaker Woofer 65 mm cone type Magnetic fluid speaker Tweeter 20 mm dome type Rated impedance 4 ohms Center speaker block Speaker system Full range speaker system Acoustic suspension Speaker 5 speakers 65 mm cone type Magnetic fluid speaker Rated impedance 4 ohms
7. set to ON when the remote control can control the TV appropriate operation may not be obtained because of the interference between the direct command from the remote control and the command via the Bar Speaker On some TVs this function may not work In this case adjust the position of the IR blaster or the Bar Speaker Enabling the Secure Link function You can specify the wireless connection to be used to link the Bar Speakerto the subwoofer using the Secure Link function This function is useful when you use multiple wireless products 1 0 indicator SECURE LINK Q aaa SEE D 9 2 ALA R 1 Press MENU on the remote control Refer to Adjusting the settings in the Operating Instructions Select WS with T Y then press ENTER Select SEC ON then press ENTER W N continued ss 96B 4 When START appears press ENTER SEARCH appears and the Bar Speaker searches for equipment that can be used with Secure Link Proceed to the next step within 2 minutes To quit the Secure Link function during a search for equipment press RETURN 5 Press SECURE LINK on the subwoofer with the point of a pen etc The indicator on the subwoofer lights in yellow OK appears on the front panel display of the Bar Speaker If FAILED appears make sure that the subwoofer is turned on and perform the process again from step 1 6 Pres
8. the remote control ofthe TV In that case connect the IR blaster supplied to the IR BLASTER jack of the Bar Speaker then enable the IR repeater function You will be able to control the TV with the remote control of the TV via the IR blaster 1 Connect the IR blaster supplied to the IR BLASTER jack of the Bar Speaker IR BLASTER 2 Place the IR blaster close to the remote control sensor of the TV aiming the IR emitter of the IR blaster at the remote control sensor of the TV Notes Refer to the operating instructions of your TV for the location ofthe remote control sensor e Connect the IR blaster before connecting the AC power cord mains lead of the Bar Speaker e Do not connect the IR blaster to a headphone jack etc of the TV Do not use the IR blaster for any other purposes ake sure that the IR repeater function is working before securing the IR e Location of the IR blaster may vary depending on the product you are using Press MENU on the remote control of the system Refer to Adjusting the settings in the Operating Instructions Select SYSTEM with t then press ENTER Select IR REP then press ENTER Select ON then press ENTER Press MENU The menu turns off JOAO Una w blaster on the Bar Speaker with the double faced adhesive tape supplied Notes e Be sure to check that the remote control of the TV cannot control the TV then set IR REP to ON If itis
9. LUETOOTH device to be connected must support the same profile as this system Even ifthe device supports the same profile the functions may differ because ofthe specifications of the BLUETOOTH device The audio playback on this system may be delayed from that on the BLUETOOTH device because of the characteristics of the BLUETOOTH wireless technology Effective communication range BLUETOOTH devices should be used within approximately 10 meters unobstructed distance of each other The effective communication range may become shorter under the following conditions e When a person metal object wall or other obstruction is between the devices with a BLUETOOTH connection e Locations where a wireless LAN is installed e Around microwave ovens that are in use e Locations where other electromagnetic waves occur Effects of other devices BLUETOOTH devices and wireless LAN IEEE 802 11b g use the same frequency band 2 4 GHz When using your BLUETOOTH device near a device with wireless LAN capability electromagnetic interference may occur This could result in lower data transfer rates noise or inability to connect If this happens try the following remedies e Try connecting this system and BLUETOOTH mobile phone or BLUETOOTH device when you are at least 10 meters away from the wireless LAN equipment e Turn off the power to the wireless LAN equipment when using your BLUETOOTH device within 10 meters Effects on other devi
10. Linear PCM Maximum 7 1ch 192 kHz or less Itis possible to input these formats only with HDMI connection Dolby Digital Video formats supported by the system Input Output HDMI Repeater block 3D File 2D Frame Side by y op and packing Side Half Bottom 720 x 576p 50 Hz O 640 x 480p 59 94 60 Hz O ir Design and specifications are subject to change without notice Information regarding environment friendly products Standby power consumption 0 5 W or less Bar Speaker 0 5 W or less Subwoofer e Over 85 power efficiency of amplifier block is achieved with the full digital amplifier S Master 3D File 2D Frame Side by Freud packing Side Half Bottom 4096 x 2160p 23 98 24Hz O 3840 x 2160p 29 97 30Hz 3840 x 2160p 25 Hz O 3840 x 2160p 23 98 24Hz 1920 x 1080p 59 94 60 Hz O O O 1920 x 1080p 50 Hz O O O 1920 x 1080p 29 97 30Hz O O O 1920 x 1080p 25 Hz O O O O 1920 x 1080p 23 98 24Hz O O O 1920 x 10801 59 94 60 Hz O O O O 1920 x 1080 50 Hz O O O O 1280 x 720p 59 94 60Hz O O O O 1280 x 720p 50 Hz O O O O 1280 x 720p 29 97 30Hz O O O O 1280 x 720p 23 98 24Hz O O O O 720 x 480p 59 94 60 Hz 1668 1768 1868 1958 HOM _xvColour DOLBY dts Bluetooth MN http www sony net 446341422 1 2013 Sony Corporation
11. Printed in Malaysia 4 463 414 22 1
12. SONY Sound Bar Reference Guide HT ST7 Do not install the appliance in a confined space such as a bookcase or built in cabinet To reduce the risk of fire do not cover the ventilation opening ofthe appliance with newspapers tablecloths curtains etc Do not expose the appliance to naked flame sources for example lighted candles To reduce the risk of fire or electric shock do not expose this appliance to dripping or splashing and do not place objects filled with liquids such as vases on the appliance The unit is not disconnected from the mains as long as it is connected to he AC outlet even ifthe unit itself has been turned off As the main plug is used to disconnect the unit from the mains connect he unitto an easily accessible AC outlet Should you notice an abnormality in the unit disconnect the main plug from the AC outlet immediately Do not expose batteries or appliances with battery installed to excessive heat such as sunshine and fire ndoor use only Recommended cables Properly shielded and grounded cables and connectors must be used for connection to host computers and or peripherals This equipment has been tested and found to comply with the limits set out in the EMC Directive using a connection cable shorter than 3 meters Notice for customers the following information is only applicable to equipment sold in countries applying EU directives This product has been manufactured by or on
13. behalf of Sony Corporation 1 7 1 Konan Minato ku Tokyo 108 0075 Japan Inquiries related to product compliance based on European Union legislation shall be addressed to the authorized representative Sony Deutschland GmbH Hedelfinger Strasse 61 70327 Stuttgart Germany For any service or guarantee matters please refer to the addresses provided in the separate service or guarantee documents Hereby Sony Corp declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC For details please access the following URL http www compliance sony de Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates a that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local Civic Office your household waste disposal service or the sh
14. ces The radio waves broadcast by this system may interfere with the operation of some medical devices Since this interference may result in malfunction always turn offthe power on this system BLUETOOTH mobile phone and BLUETOOTH device in the following locations In hospitals on trains in airplanes at gas stations and any place where flammable gasses may be present e Near automatic doors or fire alarms e This system supports security functions that comply with the BLUETOOTH specification as a means of ensuring security during communication using BLUETOOTH technology However this security may be insufficient depending on the setting contents and other factors so always be careful when performing communication using BLUETOOTH technology Sony cannot be held liable in any way for damages or other loss resulting from information leaks during communication using BLUETOOTH technology BLUETOOTH communication is not necessarily guaranteed with all BLUETOOTH devices that have the same profile as this system BLUETOOTH devices connected with this system must comply with the BLUETOOTH specification prescribed by the Bluetooth SIG Inc and must be certified to comply However even when a device complies with the BLUETOOTH specification there may be cases where the characteristics or specifications of the BLUETOOTH device make it impossible to connect or may result in different control methods display or operation e Noise may
15. coloration of the surface may result e Take care to avoid any possible injury on the corners of the Bar Speaker or the subwoofer On handling the subwoofer Do not place your hand into the slit ofthe subwoofer when lifting it The speaker driver may be damaged When lifting it hold the bottom of the subwoofer On operation Before connecting other equipment be sure to turn off and unplug the system If you encounter color irregularity on a nearby TV screen Color irregularities may be observed on certain types of TV sets If color irregularity is observed Turn off the TV set then turn it on again after 15 to 30 minutes If color irregularity is observed again Place the system further away from the TV set On cleaning Clean the system with a soft dry cloth Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzine Ifyou have any question or problem concerning your system please consult your nearest Sony dealer continued ss 5GB Copyrights This system incorporates Dolby Digital and the DTS Digital Surround System Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories Manufactured under license under U S Patent Nos 5 956 674 974 380 6 226 616 6 487 535 7 212 872 7 333 929 7 392 195 272 567 amp other U S and worldwide patents issued amp pending DTS D the Symbol amp DTS HD and the Symb
16. e this system and the BLUETOOTH device as near as possible gt Pair this system and the BLUETOOTH device again You may need to cancel the pairing with this system using your BLUETOOTH device first Pairing cannot be done 3 Bring this system and the BLUETOOTH device closer together refer to Listening to the audio from BLUETOOTH devices in the Operating Instructions gt Make sure this system is not receiving interference from a Wi Fi network other 2 4 GHz wireless devices or a microwave oven Ifa device that generates electromagnetic radiation is nearby move the device away from this system BLUETOOTH connection is disconnected No sound from the connected device is output Sound skips gt Bring this system and the BLUETOOTH device closer together gt If a device that generates electromagnetic radiation such as a Wi Fi network other BLUETOOTH devices or a microwave oven is nearby move the device away from this system gt Remove any obstacle between this system and the BLUETOOTH device or move this system away from the obstacle 3 Re position the BLUETOOTH device connected gt Try changing the Wi Fi frequency of the Wi Fi router computer etc to 5 GHz band The sound is not in sync with the image gt When you are watching movies you may hear the sound with a slight delay from the image WIRELESS SOUND No sound is output from the subwoofer 3 Make sure the AC power cord mains
17. g of this product or battery please contact your local Civic Office your household waste disposal service or the shop where you purchased the product For the customers in Australia or New Zealand For the wireless transceiver EZW RT50 It should be installed and operated with at least 20 cm and more between the radiator and person s body excluding extremities hands wrists feet and ankles 368 Table of contents PRECAUTIONS ESA A CE tada do e nl e 5 BLUETOOTH wireless technology ecccceceeeeetecteereeneneees 6 Installing the Bar Speaker on a wall oococoocccccccccoccconcconcconacinnos 7 Enabling the IR repeater function when you cannot COMO ME TV taa 8 Enabling the Secure Link function cococcccccccccocacoccnonncnnaninnoninon 9 Using the Control for HDMI function oo eee eects 10 Using BRAVIA Sync features u 11 Troubleshooting ean a a eidi 11 Specification S nee oh tern nee 14 gos Precautions On safety Should any solid object or liquid fall into the system unplug the system and have it checked by qualified personnel before operating it any further Do not climb on the Bar Speaker or the subwoofer as you may fall down and injure yourself or system damage may result On power sources Before operating the system check that the operating voltage is identical to your local power supply The operating voltage is indicated on the nameplate at the rear of the Bar Speaker elf you are not
18. lead of the subwoofer is connected gt Make sure the wireless transceivers are inserted correctly refer to Inserting the wireless transceivers in the Operating Instructions gt If the I O indicator is off Check that the AC power cord mains lead of the subwoofer is connected securely Turn the subwoofer on by pressing the 1 button on the subwoofer gt If the 1 0 indicator flashes in green slowly or is lit in red Move the subwoofer nearer to the Bar Speaker so that the indicator lights up in green Check the wireless transmission status with RF CHK refer to Adjusting the settings in the Operating Instructions If RF G appears on the front panel display push the wireless transceivers into the Bar Speaker and the subwoofer until they click Operate it as described in Enabling the Secure Link function page 9 gt If the 1 0 indicator flashes in green quickly First press the 1 0 button to turn off the subwoofer then insert the wireless transceiver into the subwoofer correctly and press the 1 0 button on the subwoofer again gt If the 1 0 indicator flashes in red Press the 1 0 button to turn off the subwoofer and check that nothing is blocking the ventilation holes of the subwoofer gt A subwoofer is for reproducing bass sound In the case of input sources that contain very little bass sound components i e a TV broadcast the sound from the subwoofer may be difficult
19. nected via the HDMI cable e Audio signals sampling frequency bit length etc transmitted from an HDMI jack may be suppressed by the connected equipment e Sound may be interrupted when the sampling frequency or the number of channels of audio output signals from the playback equipment is switched e When the connected equipment is not compatible with copyright protection technology HDCP the image and or the sound from the HDMI TV OUT ARC jack may be distorted or may not be output In this case check the specification of the connected equipment e When TV is selected for the input source of the system video signals via one of the HDMI IN jacks that was selected last time are output from the HDMI TV OUT ARC jack e This system supports Deep Color x v Colour 3D and 4K transmission e To enjoy 3D images connect a 3D compatible TV and video equipment Blu ray Disc player PlayStatione3 etc to the system using High Speed HDMI cables put on 3D glasses and then play back 3D compatible Blu ray Disc e To enjoy 4K images the TV and players that are connected to the system must be compatible with the 4K images Troubleshooting If you experience any of the following difficulties while using the system use this troubleshooting guide to help remedy the problem before requesting repairs Should any problem persist consult your nearest Sony dealer POWER The system is not turned on 3 Check tha
20. ol together are registered ademarks DTS HD Master Audio is a trademark of DTS Inc roduct includes software O DTS Inc All Rights Reserved UT UT The BLUETOOTH word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by Sony Corporation is under license This system incorporates High Definition Multimedia Interface HDMI technology The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries BRAVIA logo is a trademark of Sony Corporation x v Colour and x v Colour logo are trademarks of Sony Corporation The N Mark is a trademark or registered trademark of NFC Forum Inc in the United States and in other countries Android is a trademark of Google Inc 2012 CSR plc and its group companies The aptX mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions Other trademarks and trade names are those of their respective owners 658 BLUETOOTH wireless technology Supported BLUETOOTH version and profiles Profile refers to a standard set of capabilities for various BLUETOOTH product capabilities See Specifications page 14 on the BLUETOOTH version and profiles supported by this system Notes e For you to use the BLUETOOTH function the B
21. op where you purchased the product Europe Only Disposal of waste batteries applicable in the European Union and other European countries with separate collection systems P b This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste On certain batteries this symbol might be used in combination with a chemical symbol The chemical symbols for mercury Hg or lead Pb are added if the battery contains more than 0 0005 mercury or 0 004 lead By ensuring these batteries are disposed of correctly you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery The recycling of the materials will help to conserve natural resources In case of products that for safety performance or data integrity reasons require a permanent connection with an incorporated battery this battery should be replaced by qualified service staff only To ensure that the battery will be treated properly hand over the product at end of life to the applicable collection point for the recycling of electrical and electronic equipment For all other batteries please view the section on how to remove the battery from the product safely Hand the battery over to the applicable collection point for the recycling of waste batteries For more detailed information about recyclin
22. ou connect disconnect the AC power cord mains lead wait for more than 15 seconds and operate the system gt If you connect the audio output of the video equipment and the system using a cable other than an HDMI cable no sound may be output because of BRAVIA Sync In this case set CTRL to OFF refer to Adjusting the settings in the Operating Instructions or connect the audio output jack directly to the TV instead of the system PRTECT protect appears on the front panel display gt Press the I O button to turn off the system After STBY disappears disconnect the AC power cord mains lead then check that nothing is blocking the ventilation holes of the system RESET If the system still does not operate properly reset the system as follows 1 Press the 1 0 button to turn on the Bar Speaker 2 Press the 1 0 button while pressing INPUT and VOL on the Bar Speaker RESET appears and the system is reset The menu SOUND MODE etc return to the default settings 145 Specifications Bar Speaker SA ST7 Amplifier section POWER OUTPUT rated Front L Front R 40 W 40 W at 4 ohms 1 kHz 1 THD POWER OUTPUT reference Front L Front R speaker blocks 50 Watts per channel at 4 ohms 1 Hz Center speaker block 50 Watts per channel at 4 ohms 1 kHz Input un HDMI IN 1 2 3 OPTICAL IN 1 TV 2 ANALOG IN COAXIAL IN These 3 jacks are identical Using any
23. s MENU The menu turns off Cancelling the Secure Link function Press MENU on the remote control Refer to Adjusting the settings in the Operating Instructions Select WS with T v then press ENTER Select SEC OFF then press ENTER When OK appears press ENTER FINISH appears on the front panel display Press MENU The menu turns off Press and hold SECURE LINK on the subwoofer for several seconds until the 1 indicator turns green or flashes in green Be sure to press SECURE LINK with the point of a pen etc oa uu AWN 1068 Using the Control for HDMI function By enabling the Control for HDMI function and connecting equipment that is compatible with the Control for HDMI function via an HDMI cable operation is simplified with the features below System Power Off When you turn off the TV using the power button on the TV s remote control the system and the connected equipment turn off automatically System Audio Control If you turn on the system while you are watching the TV the TV sound is output from the speakers of the system automatically The volume of the system is adjusted when you adjust the TV volume If the TV sound was output from the speakers of the system the last time you turned off the TV the system is turned on automatically when you turn on the TV again and the TV sound is output from the speakers of the system automatically Audio Return Channel ARC
24. s not output from the subwoofer Dolby Digital or DTS multi channel sound is not reproduced gt Check the audio setting of Dolby Digital or DTS format on the Blu ray Disc player DVD player etc connected to the system The surround effect cannot be obtained gt Depending on the input signal and the SOUND MODE setting surround sound processing may not work effectively The surround effect may be subtle depending on the program or disc gt If you connect a Blu ray Disc player or a DVD player compatible with the surround effect function the surround effect of the system may not work In this case set the surround effect function ofthe connected equipment to off For details refer to the operating instructions supplied with the connected equipment BLUETOOTH BLUETOOTH connection cannot be completed gt Make sure that the BLUETOOTH indicator is lit in blue refer to Listening to the audio from BLUETOOTH devices in the Operating Instructions System status During BLUETOOTH pairing Flashes quickly in blue The system is attempting to connect Flashes in blue with a BLUETOOTH device The system has established in connection with a BLUETOOTH device The system is in BLUETOOTH standby Flashes slowly in blue mode when the system is off Indicator status Lights up in blue gt Make sure the BLUETOOTH device to be connected is turned on and he BLUETOOTH function is enabled gt Locat
25. t the AC power cord mains lead is connected securely The system is turned off automatically gt The A STBY function is working Set A STBY to OFF refer to Adjusting the settings in the Operating Instructions SOUND No TV sound is output from the system gt Make sure the input source is selected correctly You should try other input sources by pressing the INPUT button several times refer to Listening to the audio in the Operating Instructions continued ss 1168 gt Check the connection ofthe HDMI cable digital optical cable or audio cable that is connected to the system and the TV refer to Connection in the Operating Instructions gt Check that TV is displayed as the input source on the front panel display gt Check the sound output ofthe TV gt Check to make sure the TV sound volume is not too low or muted gt When a TV compatible with the Audio Return Channel ARC technology is connected with an HDMI cable check to make sure the cable is connected to the HDMI ARC jack ofthe TV gt If the TV is not compatible with the Audio Return Channel ARC technology connect the digital optical cable in addition to the HDMI cable in order to output sound The sound is output from both the system and the TV gt Turn off the sound of the system or the TV Sound lags behind the TV image gt Set SYNC to OFF if it is set to any of1 to 4 refer to
26. to hear gt Turn up the subwoofer volume by pressing the SW VOL button refer to Parts and controls in the Operating Instructions Sound skips or has noise gt f a device that generates electromagnetic radiation such as a Wi Fi network or a microwave oven is nearby move the device away from this system gt Remove any obstacle between the Bar Speaker and the subwoofer or move this system away from the obstacle gt Locate the Bar Speaker and the subwoofer as near as possible OTHERS The remote control does not function gt Point the remote control at the remote control sensor F on the system refer to Parts and controls in the Operating Instructions gt Remove any obstacles in the path between the remote control and the system gt Replace both batteries in the remote control with new ones if they are weak continued se 1368 gt Make sure you are pressing the correct button on the remote control TV remote control does not work e This problem might be solved by using the IR blaster supplied page 8 The Control for HDMI function does not work properly 3 Check the HDMI connection gt Set up the Control for HDMI function on the TV gt Make sure that any equipment connected is compatible with BRAVIA Sync gt Check the Control for HDMI settings on the connected equipment Refer to the operating instructions supplied with the connected equipment gt If y
Download Pdf Manuals
Related Search