Sony Microphone UWP-X1/X2
Contents
1. 750 66 21 794 750 67 32 803 125 66 32 796 125 67 46 804 875 66 46 797 875 67 50 805 375 66 50 798 375 Group L1 Group L2 Grouping 6 channels Grouping 6 channels CH MHz CH MHz 66 01 792 250 66 02 792 375 66 03 792 500 66 04 792 625 66 09 793 250 66 10 793 375 66 14 793 875 66 15 794 000 66 18 794 375 66 19 794 500 66 21 794 750 66 22 794 875 Group M1 Group M2 Grouping 6 channels Grouping 5 channels CH MHz CH MHz 66 31 796 000 66 32 796 125 66 33 796 250 66 34 796 375 66 39 797 000 66 40 797 125 66 44 797 625 66 45 797 750 66 48 798 125 66 49 798 250 66 51 798 500 Wireless Microphone System Frequency List for WRU 806A AU66 Model only 17 Group H1 Group H2 Grouping 8 channels Grouping 8 channels CH MHz CH MHz 67 03 799 500 67 06 799 875 67 05 799 750 67 08 800 125 67 11 800 500 67 12 800 625 67 16 801 125 67 22 801 875 67 26 802 375 67 25 802 250 67 35 803 500 67 33 803 250 67 38 803 875 67 40 804 125 67 42 804 375 67 45 804 750 Sony Corporation http www sony net2. the wireless microphone or transmitter is set to the same channel as the tuner unit If noise is heard Depending on the environment where the system is installed outside noise or radio wave may disrupt the transmission of certain channels To select a channel under this circumstance turn off the wireless microphone and transmitter Then select a channel at which the RF indicator is off A channel free from noise or radio wave interference is selected Set the same channel on the microphone or transmitter To eliminate interference or noise please note the following Do not use two or more wireless microphones or transmitters at the same time whose channel settings are the same When using two or more tuner units at the same time be sure to set them to the different channels within the same channel group Separate the reception antennas and the transmitter by more than 3 m 9 feet 11 inches When operating two or more UHF wireless microphone systems using the different wireless channels within the same group ensure that the systems are at least 100 m 330 feet apart as far as they are installed within sight of each other Reception Channel Selection Guidance on use of multichannel system This product is designed to give excellent interference free operation in multi channel systems To maintain this Sony recommends that one of the original Sony groups other than number 00 is selected These groups wi
3. 2 671 938 03 1 SON Y Tuner Base Unit Operating Instructions Before operating the unit please read this manual thoroughly and retain it for future reference MB X6 2005 Sony Corporation Owner s Record The model and serial numbers are located at the left side Record the serial number in the spaces provided below Refer to them whenever you call upon your Sony dealer regarding this product Model No MB X6 Serial No Important Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified
4. 5 67 34 803 375 67 09 800 250 67 35 803 500 67 10 800 375 67 36 803 625 67 11 800 500 67 37 803 750 67 12 800 625 67 38 803 875 67 13 800 750 67 39 804 000 67 14 800 875 67 40 804 125 67 15 801 000 67 41 804 250 67 16 801 125 67 42 804 375 67 17 801 250 67 43 804 500 67 18 801 375 67 44 804 625 67 19 801 500 67 45 804 750 67 20 801 625 67 46 804 875 67 21 801 750 67 47 805 000 67 22 801 875 67 48 805 125 67 23 802 000 67 49 805 250 67 24 802 125 67 50 805 375 67 25 802 250 67 51 805 500 67 26 802 375 Group for tuner Group 11 Group 12 Grouping 12 channels Grouping 9 channels CH MHz CH MHz 66 02 792 375 67 01 799 250 66 07 793 000 67 03 799 500 66 17 794 250 67 11 800 500 66 19 794 500 67 16 801 125 66 35 796 500 67 23 802 000 66 43 797 500 67 27 802 500 67 08 800 125 67 41 804 250 67 19 801 500 67 44 804 625 67 33 803 250 67 50 805 375 67 39 804 000 67 42 804 375 67 46 804 875 Group 13 Group A1 Grouping 9 channels Grouping 8 channels CH MHz CH MHz 66 01 792 250 66 02 792 375 66 03 792 500 66 04 792 625 66 11 793 500 66 12 793 625 66 16 794 125 66 24 795 125 66 23 795 000 67 02 799 375 66 27 795 500 67 29 802 750 66 41 797 250 67 35 803 500 66 44 797 625 67 44 804 625 66 50 798 375 Group A2 Group A3 Grouping 6 channels Grouping 6 channels CH MHz CH MHz 67 06 799 875 66 06 792 875 67 15 801 000 66 15 794 000 67 21 801
5. Eupornc Me trv nagodoa n Sony Corporation nAOveL Ott MB X6 ovupoodooverau TQOG TIS OUOLW ELG ATOLTNOELG XAL TIS AOLTEG OYETUKAEG LATA EL TNS o nytac 1999 5 EK Tia Aezvop oetec raQaxaAoVue rrwg EAEVEETE THY ax houbn ogAi a vov SLAdLXTVOV http www compliance sony de 3a norpe6urenure B EBpona C HacroarieTo Conn Koproparia qekJiapupa ue To3u MB X6 oTroBapa Ha OCHOBHUTe H3ACKBAHHA H npyrure CbOTBeTCTBALIM KJIay3M Ha Iupekrusa 1999 S EC IloqpoOHOocTu Moxe ga HaMepuTe Ha FIHTepHeT crpanunara http www compliance sony de Pro zakazniky v Evrop Sony Corporation timto prohla uje ze tento MB X6 je ve shode se z kladn mi po adavky a dal mi prislu nymi ustanovenimi smernice 1999 5 ES Podrobnosti lze z skat na n sleduj c URL http www compliance sony de Klientidele Euroopas Sony Corporation kinnitab k esolevaga seadme MB X6 vastavust 1999 5 EU direktiivi p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele Uksikasjalikum info http www compliance sony de Eur pai v s rl ink figyelm be Alulirott Sony Corporation nyilatkozom hogy a z MB X6 megfelel a vonatkoz alapvet k vetelm nyeknek s az 1999 5 EC ir nyelv egy b el r sainak Tov bbi inform ci kat a k vetkez weboldalon tal lhat http www compliance sony de Klientiem Eiropa Ar So Sony Corporation deklare ka MB X6 atbilst Direkt vas 1999 5 EK b tiskaj m pras b m u
6. PETAL Ro SOB WA PRA Z AE ENEA 6 OTS ABEND soos O clad on baa ECO O A GR ER ORO 6 OVEWIEW GoNia ip Gd FRU EDO ME Ca CU i c 6 alot JUL PPE m e Hn ue acute a aieiaa 6 Using the CD ROM manual for European model only 6 Location of Parts and Controls essere 7 Eront panel easier Od eds 7 Issuer PME 8 CONNECIION S m dia 9 Antenna Connections 2 siis Rete ea eet Rae ERR ans 9 Installing the tuner Rllss sooo wd e eet te ea Res e NET 9 About the WRU 806A WRU 806B UHF Synthesized Tuner Unii 10 Dront s 10 DISDIS EAE E E EA WOCC 11 Channel setting oto R O AG LO a Tg 11 OPO ATION wc ico cia abuse sR ahida kaiaia anaedai naekna eseat 12 Reception Channel Selection ssssooeeeeeeenenennnnnnna 13 Guidance on use of multichannel system esee 13 Automatic search and setting of available channels 13 Rack MOUNTING d ie anarei ipres oradan iana ainaani 14 Specifications ac yo 15 Wireless Microphone System Frequency List for WRU 806A AU66 Model GRIY awa zwiazana resser 16 Guidance on the use of a multi channel system 16 Group for transmitter and tuner uites R NE aesti ade 16 Group TO DGT GE REZ cosi CEA Z eie tutes 17 Table of Contents 5 6 Precautions Overview On operation The MB
7. T DC power output connectors BNC type Connect the supplied antennas or optional AN 820A UHF Antennas to these connectors When the AN 820A is used 9 V DC power is supplied to the antenna s internal booster through these connectors Never short circuit these connectors ANT IN A B ATT antenna input A B attenuation switches Select the RF attenuation level to 0 dB or 10 dB Set according to the antenna connected to the ANT IN A B DC 9V OUT connectors as follows When the supplied antennas are connected 0 dB When the optional AN 820A UHF Antennas are connected 10 dB when the length of the coaxial cables 5D 2V RG 212 U or equivalent connecting the antennas and the MB X6 are 30 m 100 feet or less or 0 dB when the cables are over 30 m 100 feet If noise or sound dropouts occur due to interferences or intermodulation set these switches to 10 dB ACIN connector Connect to an AC power source with the supplied AC power cord MIX mixed audio signal OUTPUT connector XLR 3 32 type The audio signals from 6 tuner units are mixed and output from this connector Connect to the audio input connector of a mixer amplifier or similar equipment MIX OUTPUT LEVEL switch Selects the mixed output level and tuner output level to 20 dBu or 58 dBu 0 dBu 0 775 Vrms Location of Parts and Controls Set this switch according to the input level of the equipment connected to the MB X6 Q TUNER audio
8. X6 must be used within a temperature range of 0 C to 40 C 32 F to 104 F Avoid using the unit for extended periods at extremely high temperatures or placing it in direct sunlight especially outdoors because this may damage the finish of the case Never install the unit on or near a heat source such as lighting equipment or power amplifiers Avoid using in very humid or dusty places because such use may shorten the life of the product To avoid degradation of the signal to noise ratio do not use the unit in noisy places or in locations subject to vibration such as the following near electrical equipment such as motors transformers or dimmers near air conditioning equipment or places subject to direct air flow from an air conditioner near public address loudspeakers where adjacent equipment might knock against the unit Switching lights on or off may produce electrical interference over the entire frequency range Position the unit the wireless microphones and the transmitters so that interference is minimized The tuner is precisely adjusted at the factory and no adjustment before use is necessary Do not touch the inside of the tuner or try to repair it by yourself On cleaning Clean the unit with a dry soft cloth Never use thinner benzene alcohol or any other chemicals since these may damage the finish Precautions Overview Features The MB X6 is a tuner base unit and is
9. ais informacoes por favor consulte a seguinte URL http www compliance sony de Voor de klanten in Europa Hierbij verklaart Sony Corporation dat het toestel MB X6 in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG Nadere informatie kunt u vinden op http www compliance sony de F r kunder i Europa H rmed intygar Sony Corporation att denna MB X6 star I verensst mmelse med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 1999 5 EG F r ytterligare information g in p f ljande hemsida http www compliance sony de Til europ iske kunder Undertegnede Sony Corporation erkl rer herved at f lgende udstyr MB X6 overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF For yderligere information g ind p f lgende hjemmeside http www compliance sony de Asiakkaille Euroopassa Sony Corporation vakuuttaa t ten ett MB X6 tyyppinen laite on direktiivin 1999 5 EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen Halutessasi lis tietoja k y osoitteessa http www compliance sony de For kunder i Europa Sony Corporation erkl rer herved at utstyret MB X6 er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999 5 EF For flere detaljer vennligst se http www compliance sony de 3 4 Fia Touc TIEAQTEG rou SIAHEVOUV oe XWPEC THC
10. annel of the group will be displayed About the WRU 806A WRU 806B UHE Synthesized Tuner Unit 11 12 Lo L L GP CH GP CH Display example WRU 806B U66 model Selecting the reception channel by frequency Press the button This changes the GP CH indication to the frequency indication To select a higher frequency press the button while holding down the CH button To select a lower frequency press the button while holding down the CH button Press the button again to return to the GP CH indication ke ies 82525 BET BT GP CH GP CH Display example WRU 806B U66 model d when the desired channel or frequency is displayed release the CH button and or button The selected group and channel are set To store the selected group and channel in memory Leave the indication for 1 second The group and channel set in the procedure above are automatically stored in memory Operation Operation Connect the output signals to a mixer or an amplifier see UHF page 9 synthesized wireless UHF microphone synthesized transmitter 1 Press the POWER switch on the MB X6 to turn it on The model version number such as U66 appears in the display of the tuner unit and then the setting which has been made right before the MB X6 was turned off is displayed 2 Set the reception channel 3 Turn on the wireless microphone or transmitter Be sure that
11. by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury f from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only THIS APPARATUS MUST BE EARTHED RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in t
12. capable of accomodating up to six URX MI Diversity Tuner Modules included in the UWP X1 X2 Wireless Microphone Package not supplied or WRU 806A 806B UHF Synthesized Tuner Units not supplied Suitability for channel plan for simultaneous multichannel operation The MB X6 accomodates tuner units which are suitable for channel plan for simultaneous multichannel operation without the effects of intermodulation Rack mounting The MB X6 can be mounted in an EIA standard 19 inch rack 1U size The UWP series Wireless Microphone Packages are not compatible with WRT series transmitters WRR series tuners or WRU series tuner units Using the CD ROM manual for European model only The supplied CD ROM includes versions of the Operating Instructions for the MB X6 in English French German Italian and Spanish in PDF format Preparations The following program must be installed on your computer in order to read the operating instruction contained on the CD ROM Adobe Reader Version 6 0 or higher If Adobe Reader is not installed you can download it from the following URL http www adobe com Adobe and Adobe Reader are trademarks of Adobe Systems Incorporated in the United States and or other countries Reading the CD ROM manual To read the operating instructions contained on the CD ROM do the following 1 Insert the CD ROM in your CD ROM drive A cover page appears automatically in your browser If it does
13. el higher than the current one press this button while holding down the GP or CH button Pressing this button only changes the indication on the display section from GP CH to frequency button To select a group or channel lower than the current one press this button while holding down the GP or CH button CH channel button To change the channel within the same group press the button or button while holding down this button Display 3 4 AF audio frequency indicator AF level indications When the audio output level is higher than the reference level this indicator lights up and the indications appear BATT battery indicator BATT indication This indicator starts to flash and the indication appears and also starts flashing about one hour before the battery with alarm function used with the transmitter becomes empty The time at which flashing begins will depend on the type of battery used with the transmitter and its condition GP CH group channel indication Shows the reception channel group and the channel number Pressing the button changes this indication to the frequency indication RF radio frequency indicator RF level indications When the antenna reception is optimal this indicator lights up and the indications dots appear The number of dots changes reflecting the RF input level Channel setting Take the following precautions to preve
14. encies in 125 kHz steps of TV channels 66 and 67 Guidance on the use of a multi channel system When building up a multi channel system Sony recommends that one of the groups listed under Groups for the tuner is selected to avoid mutual interference from other Sony wireless microphones transmitters Group for transmitter and tuner Group 00 TV 66 CH MHz CH MHz 66 01 792 250 66 27 795 500 66 02 792 375 66 28 795 625 66 03 792 500 66 29 795 750 66 04 792 625 66 30 795 875 66 05 792 750 66 31 796 000 66 06 792 875 66 32 796 125 66 07 793 000 66 33 796 250 66 08 793 125 66 34 796 375 66 09 793 250 66 35 796 500 66 10 793 375 66 36 796 625 66 11 793 500 66 37 796 750 66 12 793 625 66 38 796 875 66 13 793 750 66 39 797 000 66 14 793 875 66 40 797 125 66 15 794 000 66 41 797 250 66 16 794 125 66 42 797 375 66 17 794 250 66 43 797 500 66 18 794 375 66 44 797 625 66 19 794 500 66 45 797 750 66 20 794 625 66 46 797 875 66 21 794 750 66 47 798 000 66 22 794 875 66 48 798 125 66 23 795 000 66 49 798 250 66 24 795 125 66 50 798 375 66 25 795 250 66 51 798 500 66 26 795 375 Wireless Microphone System Frequency List for WRU 806A AU66 Model only TV 67 CH MHz CH MHz 67 01 799 250 67 27 802 500 67 02 799 375 67 28 802 625 67 03 799 500 67 29 802 750 67 04 799 625 67 30 802 875 67 05 799 750 67 31 803 000 67 06 799 875 67 32 803 125 67 07 800 000 67 33 803 250 67 08 800 12
15. he literature accompanying the appliance WARNING When installing the unit incorporate a readily accessible disconnect device in the fixed wiring or connect the power plug to an easily accessible socket outlet near the unit If a fault should occur during operation of the unit operate the disconnect device to switch the power supply off or disconnect the power plug CAUTION The apparatus shall not be exposed to dripping or splashing No objects filled with liquids such as vases shall be placed on the apparatus CAUTION The unit is not disconnected from the AC power source mains as long as it is connected to the wall outlet even if the unit itself has been turned off For the customers in the U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interfere
16. it into the tuner slot other than slot 1 push the corresponding blank panel from the front side of the front cover to remove it lel 17T d Insert the tuner unit into the slot until you hear a click 5 Match the six latches with the six holes on the front panel then replace the front cover Ea z EE aS 6 Tighten the screws on the front cover to secure it to the front panel of the MB X6 Connections 9 10 Removing the tuner units After removing the front cover hold the tuner unit by the top and bottom then pull it out of the slot About the WRU 806A WRU 806B UHF Synthesized Tuner Unit About the WRU 806A WRU 806B UHF Synthesized Tuner Unit This section describes parts and controls and the channel setting procedure of the optional WRU 806A WRU 806B UHF Synthesized Tuner Unit For details on parts and controls and the settings of the optional URX MI Diversity Tuner Module included in the UWP XI X2 Wireless Microphone Package refer to the Operating Instructions supplied with the UWP X1 X2 Front panel GP group button To change the group press the button or button while holding down this button Display Shows the status of the tuner and the group and channel assigned to the unit For details see the following section Display button To select a group or chann
17. ll offer excellent performance free from mutual interference from other Sony wireless microphone transmitters in the selected group when used under the recommended operating conditions The remaining groups are included for compliance with frequency regulations in various countries and will not always guarantee interference free operation Group 00 is used to scan for open channels or to use only for a one channel system Automatic search and setting of available channels When you use the MB X6 Tuner Base Unit in a multichannel operation system you can assign available channels to all tuner units by operating the tuner unit which is installed into the tuner slot 1 Automatic channel assignment function is available only when the tuner base unit holds the tuner units in the same TV channels 1 Tum off all wireless microphones and transmitters 2 On the tuner unit in the slot 1 select the group to be used 3 When the URX M1 Diversity Tuner Module included in the UWP X1 X2 Wireless Microphone Package not supplied is installed into the tuner slot 1 After confirming that the GP indication changes from flashing to lighting up about 10 seconds after performing step 2 press and hold down the button on the tuner module in the slot 1 When the WRU 806A 806B UHF Synthesized Tuner Unit not supplied is installed into the tuner slot 1 Reception Channel Selection 13 14 Press and hold down the CH butto
18. n citiem ar to saist tajiem noteikumiem Pla ka inform cija ir pieejama http www compliance sony de Europos klientams iuo Sony Corporation deklaruoja kad is MB X6 atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas Susipa inti su visu atitikties deklaracijos turiniu J s galite interneto tinklalapyje http www compliance sony de Dla klient w w Europie Niniejszym Sony Corporation o wiadcza e MB X6 jest zgodne z zasadniczymi wymaganiami oraz innymi stosownymi postanowieniami Dyrektywy 1999 5 WE Szczeg owe informacje znale mo na pod nast puj cym adresem URL http www compliance sony de Pentru clientii din Europa Prin prezenta Sony Corporation declara ca acest MB X6 respect cerintele esentiale si este in conformitate cu prevederile Directivei 1995 5 EC Pentru detalii va rugam accesati urmatoarea adresa http www compliance sony de Pre zakaznikov v Eur pe Sony Corporation t mto vyhlasuje e MB X6 spf a z kladn po iadavky a v etky pr slu n ustanovenia Smernice 1999 5 ES Podrobnosti z skate na nasledovnej webovej adrese http www compliance sony de Za stranke v Evropi Sony Corporation izjavlja da je ta MB X6 v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolo ili direktive 1999 5 ES Za podrobnosti vas napro amo e pogledate na URL http www compliance sony de Table of Contents PRECAUTIONS aaa social hueZ SZT aR 6 COTO
19. n on the tuner unitin the slot 1 The tuner unit in the slot 1 searches for available channels in the selected group and available channels in the group are so assigned to all tuner units automatically that all the tuner units use different channels After automatic setting you can adjust the groups and channels of individual tuner units Do not use group 00 When there are unavailable channels due to extraneous radio wave and the channel could not be selected on some tuner units NO CH appears on the display of those tuner units If this happens select the channel group with no interference from extraneous radio wave and repeat the procedure above Rack Mounting Rack Mounting 1 Remove the pins inside the feet at the bottom of the MB X6 using a small screwdriver or similar tool Bottom of the MB X6 2 Mount the MB X6 on the rack using screws that are at least 12 mm 1 2 inches long and that match the diameter of the screw holes on the rack Rack Specifications Audio outputs TUNER OUTPUT 1 to 6 MIX OUTPUT Connector type XLR 3 32 type male Output impedance 47 ohms or less Load impedance 600 ohms or more Reference output level 58 dBu MIC 20 dBu LINE Maximum output level 16 dBu LINE 0 dBu 0 775 Vrms General Power requirements Model for the U S A and Canada 120 V AC 60 Hz Model for other countries 230 V AC 50 60 Hz Power cons
20. nce by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For the customers in Canada This Class B digital apparatus complies with Canadian ICES 003 LE For the customers in Europe Hereby Sony Corporation declares that this MB X6 is in compliance with the essential requirements and other relevant provisions of the Directive 1999 5 EC For details please access the following URL http www compliance sony de Para clientes na Europa Sony Corporation declara que este MB X6 est conforme com os requisitos essenciais e outras disposi es da Directiva 1999 5 CE Para m
21. not appear automatically in the browser double click on the index htm file on the CD ROM 2 Select and click on the operation manual that you want to read This opens the PDF file of the operation manual The files may not be displayed properly depending on the version of Acrobat Reader In such a case install the latest version you can download from the URL mentioned in Preparations above If you have lost or damaged the CD ROM you can purchase a new one to replace it Contact your Sony service representative Location of Parts and Controls Front panel POWER switch Turns the power on and off Before turning on the MB X6 be sure to turn down the volume on the equipment connected to the MIX OUTPUT connector and the TUNER OUTPUT connectors of the MB X6 Otherwise noise may be produced when the power is turned on Front cover This cover holds the tuner units Remove the front cover when installing or uninstalling the tuner units For details see Installing the tuner units on page 9 Blank panels Remove these panels to install the tuner units For details see Installing the tuner units on page 9 Tuner slots Each slot d1 to 6 can hold a tuner unit up to 6 tuner umits in total For details see Installing the tuner units on page 9 Location of Parts and Controls 7 Hear panel ANT IN AZ antenna input A B DC 9V OU
22. nt interference and noise If there is a TV broadcasting station nearby to avoid possible interference from its broadcasting do not use that station s channel When simultaneously using two or more tuners always setthe tuners to different channels within the same group other than group 00 Press the POWER switch on the MB X6 to turn it on The model version number such as U66 appears in the display of the tuner unit and then the setting which has been made right before the MB X6 was turned off is displayed Press and hold down the GP button and press the or button to select a group Each time you press the or button the GP indication changes as shown in the figure below To change the indication continuously press and hold down the or button Display example WRU 806B U66 model The CH indication shows the lowest frequency channel of the selected group For group 00 however the channel selected last is displayed Releasing the buttons automatically cancels the group and channel selection mode and the currently displayed group is selected Press and hold down the CH button and press the or button within 3 seconds to select the channel Similar to step 2 each time you press the or button the CH indication changes in the order shown in the group and reception channel list If you press the button when the last channel of the selected group is displayed the first ch
23. signal OUTPUT connectors XLR 3 32 type Each connector supplies the audio signal from the corresponding tuner unit Connect each connector to the audio input connector of a mixer amplifier or similar equipment TUNER OUTPUT LEVEL switches Selects the tuner output level to 20 dBu or 58 dBu 0 dBu 0 775 Vrms Set these switches according to the input level of the equipment connected to the MB X6 Connections Antenna connections AN 820A UHF Antenna Antenna supplied Ci or L AC power cord supplied Output A OutputB To AC power source Connect output A or B to a mixer or amplifier Make sure to use a pair of antennas Make the antenna tips point upward Installing the tuner units Up to six URX MI Diversity Tuner Modules not supplied included in the UWP X1 X2 Wireless Microphone Package not supplied or WRU 806A 806B UHF Synthesized Tuner Units not supplied can be installed into the MB X6 Be sure to turn off the MB X6 before installing the tuner units Do not touch the connector on the rear panel of the tuner units Be careful of static electricity when installing the tuner units Installation 1 Loosen the screws at both sides of the front cover then slide the front cover downward 2 Hold the screws by the head and pull forward to remove the front cover 2 When installing the tuner un
24. umption 30 W Power supply for antenna boosters 9 V DC max 100 mA Operating temperature 0 C to 40 C 32 F to 104 F Storage temperature 20 C to 55 C 4 F to 131 F Dimensions 482 x 44 x 285 mm 19 x 1 s x11 us inches w h d 430 17 3 I N id I LO a 19 D N co oa G o Z 482 19 m K i K LI Unit mm o 400 15 3 4 inch Mass Approx 5 5 kg 12 Ib 2 oz without tuner units Supplied accessories AC power cord 1 Antennas 2 Operating Instructions 1 CD ROM 1 European model only Design and specifications are subject to change without notice Specifications 15 16 Wireless Microphone System Frequency List for WRU 806A AU66 Model only In this section the list of wireless microphone system frequencies for the AU66 model of the optional WRU 806A UHF Synthesized Tuner Unit is provided Note for users of the optional WRU 806B UHF Synthesized Tuner Unit Refer to the leaflet Wireless Microphone System Frequency List supplied with the WRU 806B Note for users of the optional UWP X1 X2 Wireless Microphone Package Refer to the leaflet Wireless Microphone System Frequency List or the CD ROM supplied with the UWP XI X2 The following tables show the channels and frequencies selectable on your wireless microphone transmitter and tuner The group 00 permits the unit to operate on any of 51 carrier frequ
Download Pdf Manuals
Related Search
Sony_Microphone_UWP X1/X2