Sony Microphone DWR-S01D
Contents
1. O N Y 4 292 344 11 1 Wireless Adapter Operating Instructions Before operating the unit please read this manual thoroughly and retain it for future reference DWA F01D DWX DIGITAL WIRELESS 2011 Sony Corporation Owner s Record The model and serial numbers are located at the side Record these numbers in the spaces provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No DWA F01D Serial No Excessive sound pressure from earphones and headphones can cause hearing loss In order to use this product safely avoid prolonged listening at excessive sound pressure levels For the customers in the U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of2. Volume Analog1 OUTPUT 1 2 MIC LEVEL AES EBU o AES EBU OUT WordSync DC DC converter Block Diagram Troubleshooting If you encounter a problem using this adapter use the following checklist to find a solution For any problems with the transmitter or receiver refer to the operating instructions of the respective device If the problem persists consult your Sony dealer Symptom Meanings Remedy The DWR S01D or the WRR 855S does not turn on The DWR S01D or the WRR 855S is not correctly inserted into the slot ofthe camcorder or this adapter Insert the DWR S01D or the WRR 855S until it is firmly and completely in and then secure it with the mounting screws No signal is output from the OUTPUT 2 connector when the adapter is connected to the device that accepts the analog signal only The tuner 2 of the DWR S01D is not turned on Turn on the tuner 2 of the DWR S01D The WRR 855S is attached to the adapter The WRR 855S is a single channel receiver Thus there is no signal output from the OUTPUT 2 connector There is noise in the audio output from the digital device that is connected to the adapter The DWR S01D inserted in the adapter and the digital device that is connected to the adapter are not in synchronization If the connected device is not compatible with the asynchronous input i e the sampling rate conv
3. a negative polarity center Before beginning operation with an external power supply avoid confusing the polarity of the external battery by checking the polarity again Parts Identification 5 6 Left Side AES EBU WORD OUT SYNC IN PHONES 4 MIC LEVEL AES EBU OUT connector BNC type Outputs AES3 format digital audio signals WORD SYNC IN word sync input connector BNC type Accepts external sync signal When the DWR SO1D is attached and the sync signal is input the DWR SO1D can be operated in synchronization with the whole audio system In order for the DWR S01D to operate in synchronization select AUTO or EXTERNAL on the SYNC SOURCE indication of the UTILITY menu of the DWR SO1D For details see On Connecting Word Clock Sync Signal and Digital Audio Signal on page 9 Note that this connector does not work when the WRR 855S is attached Parts Identification For details on the frequency of the sync signal refer to the Operating Instructions supplied with the DWR SOID Even when the 75 ohm termination has been added on the DWR S01D this connector still works as the high impedance input connector while the DWR SO1D is turned off Monitor volume adjuster Adjusts the audio volume for monitor output Adjustment is enabled only when PHONES is selected with the output selector switch Output selector switch Selects the
4. as the connectors with a dry soft cloth soon after use Lengthy use of the adapter in such places or not cleaning it after its use in such places may shorten its life Clean the surface and the connectors of the adapter with a dry soft cloth Never use thinner benzene alcohol or any other chemicals since these may mar the finish Important Notes on Operation 13 Specifications Audio section Analog output connector XLR 3 32 type OUTPUT 1 OUTPUT 2 Analog output impedance 150 ohms or less Digital output connector BNC R AES3 id output impedance 75 ohms WORD SYNC IN connector BNC R 75 ohms when the DWR SOID is attached to the adapter and 75 ohm termination is added OUTPUT 1 2 connector 6 3 5 mm TRS jack OUTPUT 1 2 level MIC LEVEL selected 52 dBu OUTPUT 1 2 level PHONES selected 50 mW 16 ohm load at T H D 1 General Power requirements 12 V DC DC IN 7 2 V DC battery Operating voltage 10 V DC to 17 V DC DC IN 6 V DC to 8 4 V DC battery Maximum continuous operation Approx 5 hours ambient temperature of 25 C 77 F fully charged Sony NP F570 lithium ion battery OUTPUT 1 2 unused DWR S01D CH1 CH2 ON wireless remote control function OFF auto switch for display set to AUTO DIMMER Specifications Operating temperature 0 C to 50 C 32 F to 122 F Storage temperature 20 C to 60 C 4 F to 140 F Dimensions unit mm inches excluding protrusions 3
5. output of the OUTPUT 1 2 connector PHONES Allows you to connect headphones to the OUTPUT 1 2 connector to monitor audio signals MIC LEVEL Allows you to connect a portable recorder or similar device to the OUTPUT 1 2 connector to record audio signals The output level is fixed MIC LEVEL is selected under factory default settings e When a WRR 855S is installed audio is not output from the right channel As noise may be generated from the output of a connected device be sure to lower the input or volume from the device to be connected before connecting to another device OUTPUT 1 2 connector 3 5 mm TRS jack tip L ring R sleeve GND Connects to headphones or portable recorders The tuner audio of the OUTPUT 1 and OUTPUT 2 connectors is output from the left and right channels respectively When a WRR 855S is installed audio is only output from the left channel DC IN external power input connector 4 pin Connect to the external power output connector of the camcorder using the supplied DC power cable This connector accepts the power voltage between 10 V DC and 17 V DC 1 GND 2 NC 3 NC 4 12V Using a Battery Inserting the Battery 1 Align the grooves on the battery with the guides on the compartment and push down the battery stopper Battery stopper Slide the battery into the compartment while maintaining its horizontal orientation until the battery stopper r
6. the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For the customers in Canada This Class B digital apparatus complies with Canadian ICES 003 For the customers in Europe This product with the CE marking complies with the EMC Directive issued by the Commission of the European Community The manufacturer of this product is Sony Corporation 1 7 1 Konan Minato ku Tokyo Japan The Authorized Representative for EMC and product safety is Sony Deutschland GmbH Hedelfinger Strasse 61 70327 Stuttgart Germany For any service or guarantee matters please refer to the addresses give
7. 855S UHF synthesizer tuner unit to be rear mounted on Sony camcorders In combination with the DWR SO1D or WRR 855S the DWA FO1D can also work as a portable wireless receiver Wide array of audio output To draw its full performance the DWA FO1D comes equipped with a wide range of interfaces One of the analog audio output connectors can be set to output the AES EBU digital format signal A word sync input connector is provided for diverse operational needs Monitor output A monitor output connector is provided to offer easy monitoring of the audio output Features Parts Identification Parts Identification Front Top Right Sides DCIN external power input remaining battery indicators Indicates the power supply status When using only a battery power supply different colors will indicate the remaining battery power OUTPUT 1 OUTPUT 2 OSG BATTERY DC IN A Remaining battery indicator Lights when a battery is inserted Green Ample battery charge remains Orange Battery charge is low Red Battery charge is nearly empty When an external power supply is also connected this indicator does not light DC IN external power input indicator Lights green when an external power supply is connected Even if an external power supply or a battery is connected the indicators will not light if the power switch on the wireless receive
8. 9 1 9 46 142 5 5 g 125 5 Mass Approx 400 g 14 oz excluding receiver and battery Supplied accessories DC power cable for 4 pin connector 1 Operating Instructions 1 Warranty booklet 1 CD ROM 1 Optional accessories LCS F01D soft carrying case Design and specifications are subject to change without notice Note Always verify that the unit is operating properly before use SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY OR FOR ANY OTHER REASON WHATSOEVER http www sony net Sony Corporation
9. er of the following conditions The device that is connected to the AES EBU OUT connector of the DWA FO1D is equipped with a sampling rate converter The DWR SOID is synchronized with the device that is connected to the DWA FOID using the master word clock signal input to the WORD SYNC IN connector of the DWA FOID There are two types of systems for synchronization using the master word clock signal System example 1 The master word clock signal is split using the T shaped BNC splitter One of the devices including the DWR S01D must be terminated For details on how to terminate the word sync signal on the DWR SOID refer to the Operating Instructions supplied with the DWR SOID a a a b ot ft l gt a 75 ohm termination setting OFF b 75 ohm termination setting ON c Master word clock signal System example 2 The master word clock signal is supplied to each device using the distributor All the devices must be terminated a a a a m c a 75 ohm termination setting ON b Master word clock signal c Word sync signal distributor Attachment and Connections 9 10 Block Diagram Step down transformer UNBAL BAL Output1 40dBu 58dBu Step down Analog2 Output2 UNBAL BAL 40dBu 58dBu
10. erter is not equipped use the word clock signal to synchronize the device The WORD SYNC IN connector is not 75 ohm terminated When the DWR S01D that is inserted in the adapter is the end device or when the master word clock signal is input to this adapter only add the 75 ohm termination to the WORD SYNC IN connector by using the UTILITY menu of the DWR S01D Mixed audio from tuner 1 and 2 is heard from the left channel of the monitor output The ANALOG OUTPUT 1 function ofthe DWR S01D is set to RX1 2 Set the function to RX1 If it is set to RX1 2 mixed audio from tuner 1 and 2 will be output for the monitor output Troubleshooting 11 12 Symptom Meanings Remedy A battery is inserted but the indicator does not light The battery is fully discharged Recharge the battery The power switch on the receiver is turned off The indicator is designed to light in accordance with the power switch on the receiver Turn on the power switch A power supply is connected to DC IN When a battery and DC IN are connected at the same time the DC IN power supply is used If you want to use the battery power disconnect the DC IN power supply Audio cannot be heard from the headphones connected to the OUTPUT 1 2 connector The monitor volume adjuster is set to a low level Adjust the volume The output selector switch is set to MIC LEVEL Se
11. eturns to its original position Using a Battery 7 8 Removing the Battery Slide the battery out while holding down the battery stopper in the direction of the arrow Attachment and Connections Attachment and Connections Attaching the Receiver Tuner Unit Insert the DWR SO1D or WRR 855S into the wireless receiver slot 1 Insert the receiver tuner unit into the wireless receiver slot after observing the direction of the D sub 15 pin connector inside the slot and that of the receiver tuner unit 2 Fasten four mounting screws of the receiver tuner unit with a screwdriver If any of the screws are loose malfunction due to vibration may occur To Connect the Power Cable Using the DC power cable supplied with the DWA FOID connect the DC IN connector to the DC OUT connector of the camcorder To Connect the Audio Cables For analog audio Connect the OUTPUT 1 or OUTPUT 2 connector on the DWA FOID to the AUDIO IN connectors on the camcorder or connected device For connected devices that accept digital audio input Connect the AES EBU OUT connector on the DWA FOID to the digital input connector on the connected device using a 75 Q BNC cable On Connecting Word Clock Sync Signal and Digital Audio Signal The DWR SO1D attached to the DWA F01D and the device connected to the DWA F01D through the digital audio interface can be operated properly under eith
12. n in separate service or guarantee documents Table of Contents Features csnessessssesnsenssnesnesnesnenssensennensensensnnsonennsnnssnennennennennenne Parts Identification Front Top Right Sides oo eee ee eeesseeseeseeseeeeeeseeeeees 4 Lett Sidene ae RER 6 Using a Battery cscscssccsscsscssscscscscscescssecssesssccsessscssesessees 7 Inserting the Battery _ cnsessessessnensnnensnnnnnnennnnnnnnn 7 Removing the Battery uesessessnesnensnennernnennennnennn nn 8 Attachment and Connections ursessesesnssesnesesnesnonesnenesnenennsansen 8 Attaching the Receiver Tuner Unit 1 2112112 1 8 To Connect the Power Cable nsennnn 9 To Connect the Audio Cables uennennen 9 On Connecting Word Clock Sync Signal and Digital Audio Signal uunneesennesseesnennernnennennnennnnn 9 Block Diagram s ssccsssssscssssscsssescescsscesssssssssssssncsssssesees 10 Troubleshooting cussossonssossonssnssnnssnssnnennnssnnsonsonssonsnnnee 11 Important Notes on Operation sersorsnssnsnssnsorsonsonsonsnnsnne 13 Notes on Using the Adapter neennessessnesnensesnennnennn 13 On Cleaning 4 res Runen 13 Specifications u scrssorsnsesnesnnensssnnsnnssnnsnnssnnsnnnsnnssonsnnssnnsnnennnene 14 Table of Contents 3 4 Features The DWA FO1D wireless adapter allows the optional DWR SO1D digital wireless receiver or the WRR
13. r is turned off OUTPUT 1 connector XLR Outputs balanced analog audio signals When a DWR SO1D is installed you can select the output tuner in the UTILITY menu of the DWR S01D Under factory default settings audio for TUNER 1 will be output When a WRR 855S is installed audio signals will be output from this connector only OUTPUT 2 connector XLR Outputs balanced analog audio signals When a DWR SOID is installed audio for TUNER 2 will be output When a WRR 855S is installed this connector does not function Wireless receiver screw holes Run in the mounting screws to secure the receiver tuner unit Battery connector Insert a battery e g NP F570 here The InfoLithium L Series is supported If a battery and an external power supply are connected at the same time the external power supply will be used The DWA FOID cannot be used to recharge the battery Use a commercially available battery charger to recharge the battery For details on inserting the battery see Using a Battery on page 7 Wireless receiver slot Insert the optional DWR S01D or WRR 855S here For details on how to attach the receiver or tuner unit to the DWA FOID see Attaching the Receiver Tuner Unit on page 8 DCIN external power input connector DC jack 8 Connects to a 10 V to 17 V DC power supply Use a plug that has an outer diameter of 65 5 mm an inner diameter of 2 1 mm and
14. t the output selector switch to PHONES Audio cannot be heard from the recorder connected to the OUTPUT 1 2 connector or the audio is distorted The output selector switch is set to PHONES Set the output selector switch to MIC LEVEL Audio is not output from the right channel of the OUTPUT 1 2 connector Tuner 2 of the DWR S01D is not turned on Alternatively a WRR 855S is connected Check the power switch on the DWR S01D As the WRR 855S is a single channel receiver output is only possible from tuner 1 i e the left channel Troubleshooting Important Notes on Operation Notes on Using the Adapter The Digital Wireless Microphone System product must be used within a temperature range of 0 C to 50 C 32 F to 122 F Operating the adapter near electrical equipment motors transformers or dimmers may cause it to be affected by electromagnetic induction Keep the adapter as far from such equipment as possible To prevent electromagnetic interference from portable communication devices The use of portable telephones and other communication devices near the DWA FOID may result in malfunction and interference with audio signals It is recommended that portable communication devices near the DWA FOID be turned off On Cleaning If the adapter is used in a very humid or dusty place or in a place subject to an active gas clean its surface as well
Download Pdf Manuals
Related Search