477 4537 SY92PX8.book(02 477 4537 GB.fm)
Contents
1. Burner min cm max cm 12 14 16 24 18 26 18 26 Make sure never to come into contact with the lid glass with pots or pans that are still hot The glass To prevent damage to the appliance or adjacent units all pans or griddles must be placed inside the perimeter of the hob AN could crack and break with the heat 15 GB IE A A Instructions for the user 7 USING THE OVEN 7 1 Before using the appliance e Remove any labels apart from the technical data plate from trays dripping pans and the cooking compartment e Remove any protective film from the outside or inside of the appliance including from accessories such as trays dripping pans the pizza plate or the base cover e Before using the appliance for the first time remove all accessories from the oven compartment and wash them as indicated in 9 CLEANING AND MAINTENANCE Heat the empty appliance to the maximum temperature in order to remove any manufacturing residues which could affect the food with unpleasant odours 7 2 Oven runners The oven features 5 runners for positioning trays and racks at different heights The insertion heights are indicated from the bottom upwards see figure models with frames 7 3 Storage compartment on some models only The storage compartment is in the bottom of the cooker It provides storage space for the appliance s metal accessories and must not be used to store2. To prevent excessive amounts of condensation from forming on the internal glass hot food should not be left inside the oven for too long after cooking While cooking desserts or vegetables excessive condensation may form on the glass In order to avoid this open the door very carefully a couple of times while cooking To prevent hazardous overheating the appliance s lid where present must always be raised when using the oven Heat the empty appliance to the maximum temperature in order to remove any manufacturing residues which could affect the food with unpleasant odours 17 Ee 535 Instructions for the user Cd 18 7 7 Electronic programmer on some models only LIST OF FUNCTIONS ia Timer key Dh End of cooking key Jff Cooking duration key Value decrease key Value increase key 7 7 1 Setting the time On the first use or after a power failure will be flashing on the oven s display Press the I and N keys together and at the same time press the value adjustment keys or this will increase or decrease the setting by one minute for each pressure Press either of the value modification keys to display the current time Before each programmer setting activate the required function and temperature 7 7 2 Semi automatic cooking Semi automatic cooking is the function which allows a cooking operation to be started and then ended after a specific length of time set by
3. The cooking temperature is selected by turning the knob clockwise to the required setting between 50 and 280 C When the knob is turned the light starts flashing to signal the oven is preheating When the selected temperature is reached a sound signal will sound and the light will stop flashing and remain lit If the temperature changes the light starts flashing again In pyrolitic models the light switches on when the automatic cleaning cycle pyrolysis starts and remains lit until the cycle is complete 4 1 3 Function selection knob The oven s various functions are suitable for different cooking modes After selecting the required function set the cooking temperature using the thermostat knob For more information on the cooking functions see 8 COOKING WITH THE OVEN The door locking device indicator light only comes on when the automatic cleaning cycle is activated 4 1 4 Auxiliary oven thermostat knob This knob allows to select the cooking function and the cooking temperature only in Static function for the auxiliary oven Turning the knob to the ste position turns on the light inside the auxiliary oven To set the knob on O turn it always anti clockwise The indicator light comes on to indicate that the oven is heating up The indicator light goes out when the set temperature is reached It flashes at regular intervals to indicate that the temperature inside the oven is being kept constantly
4. hazardous substances in electrical and electronic appliances as well as to the disposal of refuse the crossed out bin symbol on the appliance indicates that the product at the end of its useful life must be collected separately from other refuse Therefore the user must consign the product that has reached the end of its working life to the appropriate selective collection centres for electrical and electronic refuse or deliver it back to the retailer when purchasing an equivalent product on a one for one basis Adequate selective collection for the subsequent forwarding of the decommissioned product to recycling treatment and ecologically compatible disposal contributes to avoiding possible negative effects on the environment and on health and promotes the recycling of the materials of which the appliance consists The illicit disposal of the product by the user results in the application of administrative sanctions The appliance does not contain substances in quantities sufficient to be considered hazardous to health and the environment in accordance with current European directives 3 2 Your environmental care Our appliances are packed in non polluting materials which are therefore compatible with the environment and recyclable Please help by disposing of the packaging correctly You can obtain the addresses of collection recycling and disposal centres from your retailer or from the competent local organisations Do not discard the
5. appliance for heating rooms This appliance is marked according to European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE This directive defines the standards for the collection and recycling of waste electrical and electronic equipment applicable throughout the European union The identification plate with technical data serial number and brand name is located in an exposed position either in the drawer where present or on the back of the appliance A copy of the identification plate is included in the booklet It should be applied to the appropriate space on the back of the cover Do not remove this plate for any reason Before the appliance is put into operation all labels and protective films applied on external surfaces must be removed Do not use metallic sponges or sharp scrapers they will damage the surfaces Use normal non abrasive products and a wooden or plastic tool if necessary Rinse thoroughly and dry using a soft cloth Do not allow residues of sugary foods such as jam to set inside the oven If left to set for too long they might damage the enamel lining of the oven Do not use plastic kitchenware or containers The high temperatures inside the oven could melt the plastic damaging the appliance Always check that the control knobs are in the zero off position when you finish using the appliance Do not use sealed tins or containers in the appliance Overpressure may occur inside the
6. at the set level If no cooking time is selected the timer knob must be positioned on the symbol W 4 1 5 Hob burners control knob To light the flame press the knob and turn it anti clockwise to the maximum flame symbol A To adjust the flame turn the knob to the zone between the maximum AN and the minimum A settings To turn off the burner turn the knob to the position The adjacent symbol indicates the front left burner manual Instructions for the user 5 AVAILABLE ACCESSORIES NOTE Some models are not provided with all accessories Tray rack to be placed Rack useful for holding y over the top of the oven cooking containers tray for cooking foods which may drip Oven tray useful for Deep oven tray useful collecting fat from foods for baking cakes pizza placed on the rack and oven baked above desserts Rotisserie rod for Rotisserie frame cooking chicken and all supports the rotisserie foods which require m rod N Pa uniform cooking over N 7 their entire surface Reduction pan stand useful when using small pans WOK reduction useful when using a wok The oven accessories intended to come into contact with food are made of materials that comply with the provisions of current legislation Accessories available on request e Original supplied and optional accessories may be ordered from any Authorised Support Centre e Use only original accessories supplied by th
7. buzzer will start to sound intermittently After the buzzer has been deactivated the display will return to show the current time together with the Ii symbol to indicate that the oven has returned to manual use mode 7 7 5 Timer The programmer can also be used as an ordinary timer Press the key and the display will show the figures J L keep pressed and simultaneously press the value modification keys or When the key is released the count will start and the display will show the current time and the symbol fal After the setting to display the time left press the 10 key In timer mode the oven operation will not be cut out at the end of the set time 7 7 6 Adjusting the buzzer volume The buzzer volume can be varied 3 settings while it is in operation by pressing 7 7 7 Stopping the buzzer The buzzer stops automatically after about seven minutes It can be deactivated manually by pressing keys and together To switch off the appliance return all the knobs to the O setting 7 7 8 Deleting the set data Having programmed a semi automatic or automatic cooking operation this programming can be cancelled by holding down the key for the function which has just been programmed and simultaneously pressing keys or until CCC appears on the display The programmer will interpret the cancellation of the program as terminating the cooking operation 7 7 9 Modifying the set data The set cooking
8. containers during cooking creating a danger of explosion Do not cover the bottom of the oven with aluminium or tin foil sheets during cooking and do not place pans or trays on it to avoid damage to the enamelled surface Never place saucepans with bases which are not perfectly flat and smooth on the hob Unstable cookware can lead to scalding Do not rest any weight or sit on the open door of the appliance Excessive weight may jeopardise its stability General instructions GB IE The appliance becomes very hot during use Suitable heat proof gloves should be worn for all operations Do not use the hob if pyrolysis where present is taking place inside the oven If you intend to go away for a prolonged period of time close the mains gas tap or the gas cylinder tap Take care that no objects are stuck in the door of the oven Do not open the storage compartment where present when the oven is on and still hot The temperatures inside it may be very high If the surfaces are still very hot during cooking do not pour water directly onto the trays The steam could cause severe burns and damage enamelled surfaces All cooking operations must take place with the door closed The dissipation of heat may cause hazards The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance or by the use of non original
9. data can be modified at any time by holding down the function key and at the same time pressing the keys or to change the value 19 a z O 8 t C 20 Instructions for the user 8 COOKING WITH THE OVEN N d lt On multifunction models only The ECO symbol indicates which function gives the least energy consumption ECO pyrolytic models Using the grill and the lower heating element in combination is particularly suitable for cooking on a single runner only as it provides low energy consumption STATIC As the heat comes from above and below at the same time this system is particularly suitable for certain types of food Traditional cooking also known as static or thermal radiation cooking is suitable for cooking just one dish at a time Perfect for all types of roasts bread and cakes and in any case particularly suitable for fatty meats such as goose and duck GRILL The heat coming from the grill element gives perfect grilling results above all for thin and medium thickness meat and in combination with the rotisserie where present gives the food an even browning at the end of cooking Perfect for sausages ribs and bacon This function enables large quantities of food particularly meat to be grilled evenly SMALL GRILL on some models only Using only the heat released from the central element this function allows to grill small portions of meat and fish for
10. flammable materials cloths paper etc Do not open the storage compartment when the oven is on and still hot The temperatures inside it may be very high 7 4 Cooling system The appliance is equipped with a cooling system which comes into operation as soon as a cooking 16 function starts The fan causes a steady outflow of air that exits from the rear of the appliance and which may continue for a brief period of time even after the appliance has been turned off 7 5 Internal light The oven light comes on when the door is opened on some models only or any function is selected Instructions for the user GB IE 7 6 General warnings and advice for use All cooking operations must be carried out with the door closed The dissipation of heat may cause hazards During cooking do not cover the bottom of the oven with aluminium or tin foil and do not place pans or oven trays on it as this may damage the enamel coating If you wish to use greaseproof paper place it so that it will not interfere with the hot air circulation inside the oven For the best cooking results we recommend placing cookware in the centre of the rack To prevent any steam in the oven from causing problems open the door in two stages keep it half open 5 cm approx for 4 5 seconds and then fully open To access food always leave the door open as short a time as possible to prevent the temperature in the oven from falling and ruining the food
11. ones 9 5 3 Cleaning the door glazing The glass in the door should always be kept thoroughly clean Use absorbent kitchen roll remove stubborn dirt with a damp sponge and an ordinary detergent Do not use abrasive or corrosive detergents to clean the oven s door glass panels e g powder products spot removers and wire sponges Do not use rough or abrasive materials or sharp metal scrapers to clean the oven s glass doors since they may scratch the surface 9 5 4 Cleaning the door seal To keep the seal clean use a non abrasive sponge and lukewarm water The seal should be soft and flexible with the exception of pyrolitic models In pyrolitic models the seal may flatten over time and lose its original shape To restore it pinch the seal all the way along This also helps remove any dirt on the seal 2 oY VE 28 Instructions for the user 9 6 Pyrolysis automatic oven cleaning on some models only Pyrolysis is an automatic high temperature cleaning procedure which causes dirt to dissolve Thanks to this process it is possible to clean the inside of the oven with great ease During the first automatic cleaning cycle unpleasant odours may occur due to the normal evaporation of oily manufacturing substances This is an absolutely normal phenomenon which disappears after the first cleaning cycle Before starting the automatic cleaning cycle make sure that the oven does not contain any foods or large spills from previ
12. packaging or any part of it or leave it unattended It can constitute a suffocation hazard for children especially the plastic bags Your old appliance also needs to be disposed of correctly Important hand over your appliance to the local agency authorised for the collection of household appliances no longer in use Correct disposal enables intelligent recovery of valuable materials Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use to ensure that children cannot accidentally become trapped inside during play It is also necessary to cut the connecting cable to the power supply network removing it along with the plug Instructions for the user 4 GET TO KNOW YOUR APPLIANCE 8000000000 Cooking hob Control panel Oven seal Oven light Door sensor on some models only Rack tray support frame Fan Roof liner on some models only Door Storage compartment on some models only GB IE Instructions for the user ro ren ren ron 4 1 Description of the controls on the front panel 7 10 4 1 1 Programming clock The programming clock can be used to display the current time or to set a timer ora programmed cooking operation 4 1 2 Temperature selection knob
13. spare parts e154 General instructions 2 SAFETY PRECAUTIONS Consult the installation instructions for safety standards on electrical or gas appliances and for ventilation functions In your interests and for your safety the law requires that the installation and servicing of all electrical and gas appliances be carried out by qualified personnel in accordance with the standards in force Our approved installers guarantee a satisfactory job Gas or electrical appliances must always be uninstalled by suitably skilled people Before connecting the appliance to the power grid check the data on the plate against the data for the grid itself M100 0000000 If the appliance is installed on a raised platform secure it using suitable fastening systems a Before carrying out installation maintenance work make sure that the appliance is disconnected from ea the power grid If the cooking appliances are installed in motor vehicles for example camper vans caravans etc they must only be used when the vehicle is stationary Install the appliance so that when opening the drawers or doors of units positioned at the level of the hob there is no possibility of making contact with pans positioned on top of it Immediately after installation carry out a quick test on the appliance following the instructions provided later in this manual Should the appliance not function disconnect it from the power s
14. this detaches the 4 pins attached to the glass from their slots in the oven door Removing the middle glass panels e pyrolitic models there are two middle glass panels attached using 4 small locks Remove the middle panels by lifting them upwards e other models an intermediate glass panel may be present if so remove it by lifting it upwards Cleaning e tis now possible to clean the external glass panel and the panels removed previously Use absorbent kitchen roll In case of stubborn dirt wash with a damp sponge and neutral detergent Replacing the glass panels e Replace the panels in the opposite order to which they were removed e Reposition the internal glass panel taking care to centre and insert the 4 pins attached to the glass into their slots in the oven door by applying slight pressure 31 Ee 535 Instructions for the user 11 INSTALLATION 11 1 Installing in kitchen units Veneers adhesives or plastic coatings on adjacent furniture should be temperature resistant no less than 90 C If they are not sufficiently temperature resistant they may warp over time D The appliance must be installed by a qualified technician and according to the standards in force av Depending on the type of installation this appliance belongs to class 2 subclass 1 Fig A Fig B or W class 1 Fig C It may be installed next to walls one of which must be higher than the appliance at a minimum di
15. to installation The skirt must always be positioned and secured correctly on ___ the appliance 2 1 Loosen the 4 screws A on the back of the worktop 2 for i each side B 2 Place the skirt above the worktop taking care to align the H skirt s slots B with the screws A gt 3 Secure the skirt to the worktop by tightening screws A Poeg wer Pa 11 7 Positioning and levelling the appliance After making the electrical and or gas connections level the appliance on the floor by means of its four adjustable feet The appliance must be properly levelled to ensure stability 38 Instructions for the installer 12 ADAPTATION TO DIFFERENT TYPES OF GAS BEFORE PERFORMING ANY OPERATIONS SWITCH OFF THE POWER SUPPLY TO THE APPLIANCE Appliance set for gas NATURAL G20 2H pressure 20 mbar see label on product In the case of operation with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps To change the nozzles proceed as described in the following paragraphs 12 1 Replacement of nozzles on the hob 1 Remove the pan stands and remove all the burner caps and flame spreader crowns to access the burner casings 2 Unscrew the nozzles using a 7 mm socket wrench 3 Replace the burner nozzles according to the type of gas to be used see 12 3 Burner and nozzle characteristics table 4 Replace the burners in the correct position 12 2 Arrang
16. 15 20 DESSERTS Ring cake Circular 3 160 55 60 Fruit tart Circular 3 160 30 35 Fruit tart Static 3 170 35 40 Short pastry Circular 2or3 160 170 20 25 Jam tarts Turbo 2or3 160 170 40 50 Paradise cake Static 2or3 170 40 50 Paradise cake Circular 3 160 50 60 Cream puffs Turbo 3 150 160 40 50 Light sponge cake Circular 3 150 160 40 50 Rice pudding Turbo 3 160 40 50 Rice pudding Static 3 170 50 60 Croissants Circular 3 160 25 30 Croissants on multiple runners Circular Turbo 2 4 160 170 30 35 Short pastry biscuits on multiple runners Circular Turbo 2 4 160 170 16 20 The times indicated in the following tables do not include the preheating times and are provided as a guide only 23 GB IE Instructions for the user ne 9 CLEANING AND MAINTENANCE Do not use steam jets for cleaning the appliance The steam could reach the electronics damaging them and causing short circuits w CAUTION For your safety you are advised to wear protective gloves while performing any cleaning or extraordinary maintenance Do not use cleaning products containing chlorine ammonia or bleach on steel parts or parts with metallic finishes on the surface e g anodizing nickel or chromium plating We recommend the use of cleaning products distributed by the manufacturer 9 1 Cleaning stainless steel To keep stainless steel in good condition it should be cleaned regularly after use Let it cool f
17. Contents PUSS le 6 OM HONS FORU manera tie ene ene ete Renee ees eee eee ene ee eee ee eee reer 4 2 SAFETY PRECAUT IONS oats catea ogeciperarennceseeeneee waite oecussenasneacisoeeexadeaengenen cai soaencessetesaneaaeesmecoeneaie 6 o ENVIRONMENTAL CARE ieres ry sets ee see ose sees ecg ae sae seas oe es sean nee sete 8 21 Our environmental Cale sisenes nean E E EEEE EA date adnaucaiiecanmeeg E aE 8 Ore Your aNVronmMmental CALS sseisesorisnpn i eene ORERE RNEER E EEEE EERE AEEA eeaeee REKER E SEn 8 4 GET TO KNOW YOUR APPLIANCE seemsestrcectaxteseaaedonsisseesesceeenesaswses veneoeqseceseaceteceseewncoesnteieiesee 9 4 1 Description of the controls on the front panel nannonnnnnnnnnunnnnnnnnnnnnrnnnnnnnrnnenrrrsrrnnrrrrnnrrnrrnrennennrenrrsrerrrrnrnne 10 5 AVAILABLE ACCESSORIES eee nenne ee eee enn E ene eee ee eee 11 5 1 Using he rack Ol Tay eresse aa r ea ari 12 EZ U MO TAS SUPPO ACK aaa a E E E cece 12 5 3 Using the reduction pan Stands as dctavanticeeda yen isicde Ste ccwcahe canebseatsSaccesatwaandededunrianiedsscnpesnndedunudeeeteuinaladetunidaaations 12 5 4 Using the rotisserie rod ON SOME models only cccceeececeeeeecceeeecceeeeceneueeeseuceeesaeeessaueeessaeeessaeeeseeeeeeneneeeas 13 6 USING THE COOKING HOB 2 ccccccccccccccceeeeseeccteececesescuecssesenceseccessceeesesseseseescesescenesceeeseeee 14 6 1 General warnings and advice sw vvsisncriacnnenccrwarsuadedaernddaswnnedunenwuiauedawbunbuasvehonvadddesawiava
18. N 180 MIN During the automatic cleaning cycle the fans produce a more intense level of noise due to a greater rotation speed this is entirely normal and intended to facilitate heat dissipation At the end of pyrolysis the fans will continue to operate for long enough to avoid overheating the walls of adjacent units and the front of the oven Instructions for the user 9 7 Setting the cleaning cycle Turn the function selection knob to P to select the cleaning cycle Press and hold J iI press or to set the duration of the cycle The setting varies between a minimum of 1h 30m and a maximum of 3h 00m Two minutes after the cleaning cycle Pyrolysis starts a locking device will be tripped preventing the door being opened The appropriate light will switch on to indicate that the locking device has been activated At the end of the cleaning cycle the locking device will remain active until the temperature inside the oven has reached a safety threshold When the oven has cooled down collect the residues from automatic cleaning with a damp microfibre cloth To select a cleaning cycle with a delayed start after setting the duration press DM The time when the cleaning cycle will terminate will appear on the display Press and hold DM and press or to set the time at which you wish to terminate the cleaning cycle It is not possible to select any functions once the door locking device has been activated Wait f
19. e manufacturer 11 Ee 535 Instructions for the user kd ed 12 5 1 Using the rack or tray The racks and trays are equipped with a mechanical safety lock which prevents them from being taken out accidentally To insert the rack or tray correctly check that the lock is facing downwards as shown in the figure at the side To remove the rack or tray lift the front slightly The mechanical lock or the extension piece where present must always face the back of the oven Gently insert racks and trays into the oven until they come to a stop In models with runners clean the trays before using them for the first time Cleaning will remove any manufacturing residues which may otherwise scratch the sides of the oven cavity when trays are being inserted 5 2 Using the support rack The support rack is inserted into the tray as shown in the figure Using this foods can be cooked and the fat can be collected separately from the food which is being cooked 5 3 Using the reduction pan stands The reduction pan stands should be placed on top of the hob pan stands as shown in the adjacent figure Make sure they are stable The WOK pan stand should only be used when cooking with a wok Instructions for the user 5 4 Using the rotisserie rod on some models only When cooking with the rotisserie position the rod frame on the third runner see 7 2 Oven runners Once the rod frame is insert
20. ed the shaped part must sit facing outwards as shown in the figure a gt a Then prepare the rotisserie rod with the _ food using the clip forks provided Na N aAa So that you can handle the rod with the N food on it readily screw on the handle CECO nnd O AV provided en NN Having prepared the rotisserie rod with the food position it on the guide frame as shown in the figure Insert the rod into the hole detail B so that it connects with the rotisserie motor Make sure that the pin is placed correctly on the guide frame detail A 13 GB IE Instructions for the user 6 USING THE COOKING HOB 6 1 General warnings and advice Before lighting the hob burners make sure that the flame spreader crowns are correctly positioned in their housings with their respective burner caps Before lighting the burners lift the glass lid where present before closing it again turn off all the burners and wait for them to cool 6 2 Lighting the hob burners All the appliance s control and monitoring devices are placed together on the front panel The burner controlled by each knob is shown next to the knob The appliance is equipped with an electronic lighter Simply press the knob and turn it anti clockwise to the maximum flame symbol until the burner lights If the burner does not light in the first 15 seconds turn the knob to 0 and wait 60 seconds before trying again After lighting
21. eeeesueeeeseeseesseeeeess 23 9 CLEANING AND MAINTENANCE aeseersicc ene a sce ceecneecce sess sea eatennnnaceubasesoeuen Guacsncenseeesoraeenwestsemanest 24 9 1 Cleaning stainless steel cc cecccccescccseeeeceeseecceeeeceeeeeceeueeeeeuseeseaseecsageceseseessageeesageeessueeesseeeessaeeesaseesseeeeess 24 O52 Ordifialy Gail ClEAMING ae E E E E S E 24 9 3 Food stains or residues ccccccssececeececeeeeceseeseueeeceeeseeceneueeseeeseaeeeeseeeseeeenensesegeeteaeeeeueeseeeeeueeenseseneutensneenens 24 9 4 Cleaning the cooking hob parts sicincciiwistenutenarsanwnscunnesilenatoassaveknmensexubaiedannnlawelneslentounsaveunadieeathaineiadsatatensesundens 24 9 5 Cleaning te OV OM ssec eni E NE E a rE ance a E i 26 9 6 Pyrolysis automatic oven cleaning on some models only cccseeeeeceeeeeceeeeeeneeeeeseeeeeeeeeeeeseeeeeseeeeeeseeeeeas 28 Sro NONE Cleaning CYOSE sereen A E E 29 10 EXTRAORDINARY MAINTENANCE cccccccecccceeceeeeeeceeeeseeeeseeeseeeeseasessueeseeeesaeeesaeeeas 30 1O PACA OV INO NG GOOF e E E E E A 30 10 2 Replacing the light bulb main OVEN eee cece eeccceeeeceeeeceeeeeceeeecaeeeceueeceueeceueeeseueesaeeeseeesaneeseueessueeesaeeesaees 30 10 3 Replacing the light bulb auxiliary OVEN cccccecccccseeeecceseeecaeeeeeseueeessaeeeeseeeeesaeeessaeeeesaeeeeseueeesseeeseneueeesaes 31 10 4 Removing the internal glass panels ccccceccssececsscceseesesececseeeseeseseuseseueeseueeesseeesseee
22. ement of burners a 39 GB IE Burner Auxiliary Semi rapid Rapid Ultra rapid Burner Auxiliary Semi rapid Rapid Ultra rapid 40 Instructions for the installer 12 3 Burner and nozzle characteristics table Rated heating LPG GAS G30 G31 28 30 37 mbar capacity kW Pisa Reduced Capacity Capacity 1 100 mm capacity W g h G30 g h G31 1 05 50 400 76 75 1 8 65 500 131 129 3 0 85 800 218 214 3 9 100 1600 283 278 elegans NATURAL GAS G20 20 mbar capacity kW Nozzle Prechamber Reducerea diameter printed on W racer 1 100 mm nozzle 1 05 72 X 400 1 8 97 Z 500 3 0 115 Y 800 3 9 135 K 1600 12 4 Final operations After replacing the nozzles reposition the flame spreader crowns the burner caps and the pan stands Following adjustment to a gas other than the one originally set in the factory replace the gas setting label fixed to the appliance with the one corresponding to the new gas The label is inserted inside the nozzle pack where present 12 4 1 Adjusting the hob burner minimum setting for city or natural gas Light the burner and turn it to the minimum position Extract the gas tap knob and turn the adjustment screw next to the tap rod depending on the model until the correct minimum flame is achieved Refit the knob and verify that the burner flame is stable when turning the knob rapidly from the maximum to the minimum position the
23. eralonS cites csecatiegcncseaca te aei e eea ei eene aaa erae ei Ee ra e eaea aa Ease tates 41 INSTRUCTIONS FOR THE USER these instructions contain user recommendations a description of the controls and the correct procedures for cleaning and maintenance of the appliance INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified technician who must install the appliance set it functioning and carry out an inspection test Further information about the products can be found at www smeg com N tl l i General instructions 1 INSTRUCTIONS FOR USE This manual is an integral part of the appliance It must be kept in its entirety and in an accessible place for the whole working life of the appliance We recommend reading this manual and all the information it contains carefully before using the appliance Installation must be carried out by qualified personnel in accordance with the standards in force This appliance is intended for domestic use and conforms to the EC directives currently in force The appliance has been built to carry out the following functions cooking and heating up food all other uses are considered unsuitable These instructions are valid only for the destination countries whose identifying symbols are included on the cover of this manual Never obstruct the openings and slots provided for ventilation and heat dispersal this may cause malfunctions Do not use this
24. ever with a flame The tightening torque between connections that incorporate a gasket must be between 10 and 15 Nm After carrying out any operation on the appliance check that the gas connections are properly tightened If the appliance is fuelled by LPG use a standards compliant pressure regulator and connect to the gas cylinder in accordance with the standards in force Make sure that the feed pressure complies with the values indicated in the table 12 3 Burner and nozzle characteristics table 11 4 1Connection with a rubber hose CAUTION The following instructions are valid solely for Class 1 installations See fig C in chapter 11 1 Installing in kitchen units Connection using a rubber hose complying with current standards is only permitted if the hose can be inspected along its entire length The inside diameter of the hose must be 8 mm for LPG GAS and 13 mm for NATURAL GAS and CITY GAS Installation with a standards compliant rubber hose must be carried out so that the length of the piping does not exceed 1 5 metres make sure that the hose does not come into contact with moving parts and that it is not crushed in any way Verify that all the following conditions are met e the hose is fixed to the hose connection with safety clamps no part of the hose is in contact with hot walls max 50 C the hose is not under traction or tension and has no kinks or twists the hose is not in contact with sharp object
25. flame must not go out Repeat the operation on all the gas taps 12 4 2 Adjusting the hob burner minimum setting for LPG In order to adjust the minimum setting with LPG the screw at the side of the tap rod must be tightened clockwise all the way 914774537 C
26. for meat vary according to the thickness and quality of the food and to consumer taste We recommend using a meat thermometer for meat when roasting it Alternatively simply press on the roast with a spoon if it is hard it is ready if not it needs another few minutes cooking 8 1 3 Advice for cooking desserts and biscuits Use dark metal moulds for desserts they help to absorb the heat better The temperature and the cooking time depend on the quality and consistency of the dough Check whether the dessert is cooked right through at the end of the cooking time put a toothpick into the highest point of the dessert If the dough does not stick to the toothpick the dessert is cooked If the dessert collapses when it comes out of the oven on the next occasion reduce the set temperature by about 10 C selecting a longer cooking time if necessary 8 1 4 Advice for defrosting and proving We recommend positioning frozen foods in a lidless container on the first shelf of the oven The food must be defrosted without its wrapping Lay out the foodstuffs to be defrosted evenly not overlapping When defrosting meat we recommend using a rack positioned on the second runner with the food on it and a tray positioned on the first runner In this way the liquid from the defrosting food drains away from the food The most delicate parts can be covered with aluminium foil For successful proving a container of water should be placed in the bo
27. in the indicated direction Replace the bulb with one of the same type 25W for filament bulbs or 40W for halogen bulbs poe Do not touch halogen bulbs directly with your fingers wrap them in insulating material 30 Instructions for the user GB IE 10 3 Replacing the light bulb auxiliary oven If a light bulb needs to be replaced because it is worn or burnt out unscrew the bulb cover Remove the bulb by unscrewing it and then replace it with a similar bulb 25W 10 4 Removing the internal glass panels The glass in the door should always be kept thoroughly clean To facilitate cleaning it is possible to remove the door see 10 1 Removing the door and place it on a canvas or open it and lock the hinges in order to extract the glass panels The glass panels of the door can be completely removed by following the instructions provided below Warning before removing the glass panels make sure that at least one of the door s hinges has been AN locked in the open position as described in chapter 10 1 Removing the door This operation may have to be repeated during the glass removal process if the door is accidentally freed Removing the internal glass panel e Remove the internal glass panel by pulling the rear part E gently upwards following the movement indicated by the arrows 1 e Then pull the front of the glass panel upwards 2 e Doing
28. irst 9 2 Ordinary daily cleaning To clean and preserve the stainless steel surfaces always use only specific products that do not contain abrasives or chlorine based acids How to use pour the product onto a damp cloth and wipe the surface rinse thoroughly and dry with a soft cloth or a microfibre cloth 9 3 Food stains or residues Use ordinary non abrasive products with the aid of wooden or plastic utensils if necessary Rinse thoroughly and dry with a soft cloth or a microfibre cloth _ Do not allow residues of sugary foods such as jam to set inside the oven If left to set for too long they py might damage the enamel lining of the oven lt Do not use metallic sponges or sharp scrapers as they will damage the surfaces LE 9 4 Cleaning the cooking hob parts 9 4 1 Pan stands Remove the pan stands and clean them with lukewarm water and non abrasive detergent making sure to remove any encrustations Dry them thoroughly and return them to the hob Continuous contact between the pan stands and the flame can cause modifications to the enamel over time in those parts exposed to heat This is a completely natural phenomenon which has no effect on the operation of this component Do no wash these parts in a dishwasher 24 A Instructions for the user 9 4 2 Burner caps and flame spreader crowns The burner caps and flame spreader crowns can be removed for easier cleaning Wash them in warm water and a non abrasive de
29. keep the knob pressed down for a few seconds to allow the thermocouple to heat up The burner may go out when the knob is released in this case the thermocouple has not heated up sufficiently Wait a few moments and repeat the operation keeping the knob pressed for longer lo S7 If the burners should go out accidentally a safety device will be tripped cutting off the gas supply even if the gas tap is open In this case turn the knob to the OFF position and wait at least 60 seconds before trying to light the burner again 6 3 Practical hints for using the hob burners For better burner efficiency and to minimise gas consumption use pans with lids and of a suitable size for the burner so that the flames do not reach up the sides of the pan see paragraph 6 4 Pan diameters Once the contents come to the boil turn down the flame far enough to ensure that the liquid does not boil over If any liquid does boil over or spill remove the excess from the hob To prevent burns or damage to the hob during cooking all pans or griddles must be placed inside the perimeter of the hob All pans must have smooth flat bottoms If the flame accidentally goes out turn off the control knob and wait at least 1 minute before trying to re light the burner Take the greatest care when using fats or oils since they may catch fire if overheated 14 Instructions for the user 6 4 Pan diameters
30. lanning by a specialist qualified in this area and must comply with the positions and distances indicated by the standards When the job is complete the installer must issue a certificate of conformity En Extraction using a hood 2 Extraction without a hood t A Single natural draught chimney Single chimney with extractor fan Directly outdoors with wall or C window mounted extractor fan D Directly outdoors through wall a Air ao Combustion products eR Extractor fan 33 eS Instructions for the user PN 11 3 Wall mounting brackets where present The fastening system provided must be installed to ensure the appliance is stable If installed correctly this system prevents the appliance tipping over Use the adjustable feet to level the appliance at Measure the distance from the index of the the required height opening to the floor 3 4 Use the same height on the wall to drill the Before tightening the brackets fully to the wall holes for fastening the brackets The distance check that the index on the brackets is at the between the centres of the holes is given in the same height as the index on the back of the diagram above appliance Position the appliance taking care that the brackets are correctly inserted 34 sa Joe YY Instructions for the user GB IE 11 4 Gas connection At the end of the installation check for any leaks with a soapy solution n
31. making kebabs toasted sandwiches and any types of grilled vegetable side dishes ROTISSERIE GRILL on some models only The rotisserie works in combination with the grill element allowing to perfectly brown food BOTTOM The heat coming just from the bottom allows to complete the cooking of foods that require a longer basic cooking time without affecting their browning Perfect for cakes pies tarts and pizzas FAN ASSISTED STATIC The operation of the fan combined with traditional cooking ensures uniform cooking even with complex recipes Perfect for biscuits and cakes even when simultaneously cooked on several levels Instructions for the user FAN ASSISTED GRILL The air produced by the fan softens the strong heatwave generated by the grill grilling perfectly even very thick foods Perfect for large cuts of meat e g shin of pork FAN ASSISTED BOTTOM on some models only The combination of the fan with just the lower heating element allows cooking to be completed more rapidly This system is recommended for sterilising or for finishing off the cooking of foods which are already well cooked on the surface but not inside which therefore need a little more heat Perfect for any type of food CIRCULAR The combination of the fan and the circular element incorporated in the rear of the oven allows to cook different foods on several levels as long as they need the same temperatures and same type of co
32. oking Hot air circulation ensures instant and uniform distribution of heat It will be possible for instance to cook fish vegetables and biscuits simultaneously on different levels without mixing odours and flavours TURBO The combination of fan assisted cooking and traditional cooking allows to cook different foods on several levels extremely quickly and efficiently without odours and flavours mingling Perfect for large volumes that call for intense cooking DEFROSTING on the multifunction model only Rapid defrosting is helped by switching on the fan to ensure uniform distribution of air inside the oven 21 GB IE Instructions for the user 8 1 Cooking advice and instructions 8 1 1 General advice We recommend preheating the oven before putting the food in Place the food in the oven only once the cooking light is off For cooking on several levels we recommend using a fan assisted function to achieve uniform cooking at all heights In general it is not possible to shorten the cooking times by increasing the temperature the food could be well cooked on the outside and undercooked on the inside While cooking desserts or vegetables excessive condensation may form on the glass In order to avoid this open the door very carefully a couple of times while cooking For rapid preheating use a fan assisted function then select the required function 8 1 2 Advice for cooking meat Cooking times especially
33. or g to go out 29 e 535 Instructions for the user 10 EXTRAORDINARY MAINTENANCE The oven requires periodic minor maintenance or replacement of parts subject to wear such as gaskets light bulbs etc Specific instructions for each operation of this kind are given below Before any intervention that requires access to live parts disconnect the appliance from the power supply CAUTION For your safety you are advised to wear protective gloves while performing any ie y cleaning or extraordinary maintenance 10 1 Removing the door 30 Open the door completely Grasp the door on both sides To reassemble the door put the Insert a pin into the hole in the with both hands lift it forming an hinges in the relevant slots in the hinge Repeat for both hinges angle of around 30 and remove it oven making sure that grooved sections C are resting completely at the base of the slots Lower the door and once it is in place remove the pins from the holes in the hinges 10 2 Replacing the light bulb main oven If a light bulb needs to be replaced because it is worn or burnt out remove the guide frames see 9 5 1 Removing guide frames and self cleaning panels where present a Then remove the bulb cover using a tool e g a j screwdriver P Remove the bulb by unscrewing filament bulbs or pulling it halogen bulbs
34. ous cooking operations During the pyrolysis cycle a door locking device makes it impossible to open the door 9 6 1 Before starting the automatic cleaning cycle Pyrolysis may be carried out at any time of the day or night if you wish to benefit from the lower cost of electricity overnight e Completely remove all accessories from inside the oven The roof liner is not considered an accessory and must therefore be kept inside the oven e Remove the guide frames see 9 5 1 Removing guide frames and self cleaning panels where present In order not to damage the internal glass panel it should be cleaned in accordance with the usual procedure see 9 5 3 Cleaning the door glazing before starting the automatic cleaning cycle For very stubborn encrustations lock the door using the pins provided and remove the glass panel Spray an oven cleaning product onto the glass read the warnings on the product leave for 60 minutes then rinse and dry the glass using kitchen roll or a microfiber cloth After carrying out these operations position the glass panel on the door again and remove the pins locking it e At the end of the cleaning cycle when the oven has cooled down reinsert the frames by repeating the previously used procedure in reverse order e Make sure that the oven door is firmly closed e Refer to the following diagram for setting the cleaning cycle duration CLEANING DURATION LIGHT DIRT MEDIUM DIRT 90 MIN 135 MI
35. oving the guide frames and the self cleaning panels enables the sides to be cleaned more easily This operation should be carried out each time the automatic cleaning cycle is used on some models only To remove the guide frames 1 Pull the frame towards the inside of the oven to unhook it from its housing A then slide it out of the seats at the back B 2 When cleaning is complete repeat the above procedures to put the guide frames back in Instructions for the user GB IE 9 5 2 Cleaning the self cleaning panels on some models only If the self cleaning panels are dirty primarily with small amounts of grease a regeneration cycle through heating can be carried out Clean the base and the roof liner first with a microfibre cloth soaked in water and neutral washing up liquid then rinse thoroughly Set a regeneration cycle by selecting a fan assisted function at the maximum temperature for one hour See 6 7 Selecting a cooking function If the panels are particularly dirty after the regeneration cycle remove them and wash them with neutral washing up liquid Then rinse and dry them Put the panels back in the oven and set a fan assited function at a temperature of 180 C for one hour in order to ensure that they are thoroughly dry We recommend carrying out the self cleaning panel regeneration cycle every 15 days The panel regeneration cycle is a cleaning method suitable for grease residues not sugar based
36. r use of tools can cause hazards AN This appliance must not be controlled using an external timer or remote control system General instructions GB IE Be aware of how rapidly the cooking zones heat up Do not place empty saucepans on the heat Danger of overheating Fats and oils can catch fire if they overheat You are therefore recommended not to leave the appliance while preparing foods containing oils or fats If fats or oils catch fire never put water on them Place the lid on the saucepan and turn off the cooking zone Take care when using additional electrical appliances in the kitchen e g blender toaster etc Connection cables must not come into contact with hot cooking zones Do not use steam jets for cleaning the appliance The steam could reach the electronics damaging them and causing short circuits Do not spray any spray products near the household appliance while it is in operation Do not use spray products while the appliance is still hot The gases contained in the spray may catch fire The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance or by the use of non original spare parts GB IE Instructions for disposal Z 3 ENVIRONMENTAL CARE 3 1 Our environmental care Pursuant to Directives 2002 95 EC 2002 96 EC 2003 108 EC relating to the reduction of the use of
37. s or sharp corners if the hose is not perfectly airtight and leaks gas do not try to repair it replace it with a new hose e verify that the hose is not past its expiry date serigraphed on the hose itself 35 GB IE Instructions for the installer Connect to the appliance using a BS 669 compliant bayonet hose The connector at the back of the appliance has a 1 2 fo BSP external thread Apply insulating material to the thread of ae the gas pipe connector 4 and then tighten the adapter 3 to it as To indicated in the figure Screw the assembly to the movable connector 1 of the appliance placing the seal 2 between them 36 Instructions for the installer GB IE 11 5 Electrical connection Make sure the voltage and the cross section of the power supply line match the specifications indicated on the identification plate positioned on the appliance Do not remove this plate for any reason A copy of the plate is attached to the instructions Fam 1 The appliance must be connected to the power supply by a qualified technician Before performing any operations switch off the power supply to the appliance The appliance must be connected to earth in compliance with electrical system safety standards Where the appliance is connected to the power grid via plug and socket both of these must be of the same type and connected to the power cable in accordance with current standards The socket m
38. ssuectsneeteseeseueesseesenaass 31 1 WINS TAL MON re scesteccceraecasciea esse E E E E 32 Tiot mStalling N KICNON UNITS scdsujessanoscnnagtenesanccaatsecesueussieceeasaespavadtecasod A A aaa Aei 32 11 2 Room ventilation and combustion extraction ccceecccceeeeceeeeceeeeceeeeeseeeesaeeeseeeeseeeesseeessaeeeseeeesaeesaneeesaeeenaaes 33 11 3 Wall mounting brackets where present cccccccssecceeeeceeeeeceeeecaueeceeeeceueeseueeeseueeseeeeseeeeseeeesaeesaueeeseeesagss 34 114 GaS COMMCCHON sacwsinccmesrimutacesavaccetonessesesaumtasmespinardaat dunseeonsaeneduneouaiaednuninanscumaoudesribeseneaenoinanssdnrsberunmmumagiuns 35 11 5 Electrical Conneccion saisissent inen i e E Er eeke oi ob Taaie enan ree e LEERE 37 11 6 Positioning the skirt on some models only ccccceeseccseeeecseeeeeceeeeeceeeeeeeeeeeseueeessaeeeesegeeesseeeesseeeessaeeeeseass 38 11 7 Positioning and levelling the appliance ec eecccseccceeceseeeeseseeseececseeensesessueeseueeseueeeeeeesseeeeeaeensueeseneeseaess 38 12 ADAPTATION TO DIFFERENT TYPES OF GAS ccccccccccccseeeeceeeeeseeeesaeeeeseeeeesaeeesaaes 39 12 1 Replacement of nozzles ON the NOD ccc cccceeccceeeceeecceeeceeecaeeecaeeceecaueesaeeseuecaueesaeeseuesaueesaeessueseeeeseeesenees 39 WA PAG eIMenl Or DUIST s E E E E O A 39 12 3 Burner and nozzle characteristics table ceecccseeccseeeeeeeeeeeeeeeeeeeseaeeseaeeseaeeesaeeeseeeessueessneeseneeseeeesaeeenaaes 40 124 Finalop
39. stance of 50 mm from the side of the appliance as shown in figures A and C relative to the installation classes Any wall units must be at a minimum distance of at least 750 mm above the appliance This distance can be reduced to 650 mm if a ventilation hood is installed A Built in appliance Class 2 subclass 1 B Built in appliance Class 2 subclass 1 Free standing appliance Class 1 ww QG UIW ww QG UIW OO 0000 Gy OO 0000 i o 32 im Instructions for the user GB IE 11 2 Room ventilation and combustion extraction The room containing the appliance should be permanently ventilated in accordance with the standards in force The room where the appliance is installed must have enough air flow as required for the regular combustion of gas and by the necessary air exchange of the same room The air vents protected by grills must be suitably dimensioned in compliance with current standards and positioned so that no part of them is obstructed The appliance must be kept adequately ventilated in order to eliminate the heat and humidity produced by cooking in particular after prolonged use you are recommended to open a window or to increase the speed of any fans Combustion products can be extracted by means of hoods connected to a natural draught chimney whose efficiency is assured or via forced extraction An efficient extraction system requires precision p
40. tergent making sure to remove any encrustation then wait until they are perfectly dry Refit the flame spreader crowns making sure that they are correctly in place with their respective burner caps and ensuring that the holes A in the flame spreaders are aligned with the igniters and thermocouples Do no wash these parts in a dishwasher 9 4 3 Igniters and thermocouples For correct operation the igniters and thermocouples must always be perfectly clean Check them frequently and clean them with a damp cloth if necessary Remove any dry residues with a wooden toothpick or a needle Do not use cleaning products containing chlorine ammonia or bleach on steel parts or parts with metallic finishes on the surface e g anodizing nickel or chromium plating 25 Ee 535 Instructions for the user 3 z 4 BSN EY 26 9 5 Cleaning the oven For the best oven upkeep clean it regularly after having allowed it to cool Take out all removable parts e Clean the oven racks with hot water and non abrasive detergent Rinse and dry e For easier cleaning the door can be removed see 10 1 Removing the door The oven should be operated at the maximum heat setting for 15 20 minutes after use of specific products to burn off the residues left inside the oven When the operation is complete damp parts should be dried thoroughly 9 5 1 Removing guide frames and self cleaning panels where present Rem
41. the user Press the i key and the display will light up showing the figures JC L keep it pressed and at the same time use the keys or to set the cooking duration When is released the count of the programmed cooking duration will start and the display will show S585 the current time together with ffl and A to indicate that a programmed cooking operation has been set 7 7 3 Automatic cooking This function switches the oven on and off in fully automatic mode Press the jill key and the display will light up showing the figures L L keep it pressed and at the same time use the value modification keys or to set the cooking duration Press the Df key and the display will show the sum of the current time plus the cooking duration keep it pressed and at the same time use the value modification keys or to adjust the end of cooking time When the ys key is released the programmed count will start and the display will show the current time together with the symbols A and ffi After making the setting press the fifi key to view the remaining cooking time press the De key to view the cooking end time The logic prevents the setting of incompatible values e g the programmer will not accept a cooking end time with a duration which is too long for its value Instructions for the user GB IE 7 7 4 End of cooking At the end of cooking the oven will switch off automatically and simultaneously a
42. ttom of the oven 8 1 5 Advice for cooking with the Grill and the Fan assisted grill 22 Using the Grill function a meat can be grilled even when it is put into the cold oven preheating is recommended if you wish to change the effect of the cooking A however we recommend that you preheat the oven before e e T With the Fan assisted grill function grilling Instructions for the user 8 2 Cooking operation information table GB IE Types of food Weight Function punter Poo en aonb men FIRST COURSES Lasagne 3 kg Static 2or3 220 230 40 50 Oven baked pasta Static 2or3 220 230 40 MEAT Roast veal 1 Kg Circular 3 180 190 70 80 Pork loin 1 Kg Circular 3 180 190 70 80 Shoulder of pork 1 Kg Turbo 3 180 190 90 100 Roast rabbit 1 Kg Circular 3 180 190 70 80 Turkey breast 1 Kg Turbo 3 180 190 110 120 Roast neck of pork 1 Kg Turbo 3 180 190 190 210 Roast chicken 1 Kg Turbo 3 190 200 60 70 GRILLED MEATS 15t side 2 side Pork chops Fan assisted grill 5 250 7 9 5 7 Fillet of pork Grill 4 250 9 11 5 9 Fillet of beef Grill 4 250 9 11 9 11 Liver slices Small grill 5 250 2 3 2 3 Sausages Fan assisted grill 4 250 7 9 5 6 Meatballs Grill 4 250 7 9 5 6 ROTISSERIE MEAT where present Chicken Rotisserie grill On a rotisserie rod 250 60 70 FISH Salmon trout 0 7 Kg Circular 3 160 170 35 40 BREAD and FOCACCIA Pizza Turbo 1 250 6 10 Bread Circular 2 190 200 25 30 Focaccia Turbo 2 180 190
43. unenduiaancansaenaawelnsuanddabwasars 14 BZ LENU NONON DUNOIS aee a E E EEA AEE 14 6 3 Practical hints for using the hob burners cecccceececseeeeeeeeeeeeeseeeesaneeeeaeeseaeeesaeeesaeeesaeeeseueesseeeeseeeeseaeeseneesees 14 DAEA M a E E se E ee eer eee ee 15 T USING THE OVEN siereisieennes nig reitin annie Ear AAEREN EENAA RAIRE TENE RENARE EEEE EELNE ARANEA 16 7 1 Before using the appliance sccencictsaccvastecansarctadseusnasbed lt xtdeahebiesaieinatcssdcacehecsddenaa adadsuswintdeadeasiinbeners nel dedeseatindersacauecn 16 TIVER TONOS Sare E eee E E E E ee E 16 7 3 Storage compartment on some models only ccceeccceeeeceeeeceeeeeceeeeceeeeseuceceueeseueesseeeseeeeseueesaeeesueesseeesaes 16 TEE e ER EE E E A umes AE S A ETE E A E E E E torsade 16 TANEN G e E E E E E E 16 7 6 General warnings and advice for USE ccccseeeccceeececeeseeceeseeeceuseeceasececeececsuseeesadeeeseuseessseeeesaeeesaneeesseeeeens 17 7 7 Electronic programmer ON some models only ceececsececeeeeeceeeeceeeeceeeceecessueeesaeeeseueeseueeseueessueesaeeesaeeesses 18 BOOKING WEER TAE OVEN orenera deces nce eens codecs gseetea aden santos see 20 8 1 Cooking advice and instructions os gaantecpitwseniaaccssanied eiecta cn salen de tomnieastanee gases accuse asta ned snieaneiassmaiaaantcnncninedeiiee ciicd durant meaieucaanats 22 8 2 Cooking operation information table ce eccecseeeccseeceeceeeecneeeeneeeeecseeeessaaeeeseueeesseueeeseeeess
44. upply and call the nearest technical assistance centre The plug to be connected to the power supply cable and its socket must be of the same type and conform to the standards in force The socket must be accessible after the appliance has been installed Never disconnect the plug by pulling on the cable If the power supply cable is damaged contact the technical support service immediately and they will replace it The appliance must be connected to earth in compliance with electrical system safety standards During use the appliance and its accessible parts become very hot Take care never to touch the heating elements Keep children younger than 8 away from the appliance unless under continuous supervision Never put inflammable objects in the oven they could be accidentally ignited and cause fires The appliance is intended for use by adults Do not allow children to go near it or play with it This appliance may be used by children from the age of 8 and by people of reduced physical and mental ability or lacking in experience and knowledge provided they are supervised or instructed on the safe use of the appliance and if they understand the associated risks Do not allow children to play with the appliance Do not allow unsupervised children to perform cleaning or maintenance operations Never attempt to repair the appliance All repairs must be carried out by an authorised technician or at an authorised service centre The imprope
45. ust be accessible after the appliance has been built in NEVER UNPLUG BY PULLING ON THE CABLE plug is torn off the power cable it is the last to be detached Avoid use of adapters and shunts as these could cause overheating and risk of burns If a fixed connection is being used fit the power line with an omnipolar circuit breaker with a contact opening gap equal to or greater than 3 mm in an easily accessible position close to the appliance The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance A Should the earthing wire need replacing it must be longer than the current conduction wires so that if the K Sif K POSSIBLE CONNECTION CABLE TYPE TYPES if not present 380 415 V 2N 4 x 1 5 mm HO5V2V2 F 123 45 l i p 220 240 V 1N HO5V2V2 F e Use H0O5V2V2 F cables resistant to at least 90 C S7 e The values indicated above refer to the cross section of the internal conductor e The tightening torque of the screws of the terminal supply wires must be 1 5 2 Nm e The aforementioned power cables are sized taking into account the coincidence factor in compliance with standard EN 60335 2 6 37 Instructions for the installer 11 6 Positioning the skirt on some models only WARNING The skirt provided is an integral part of the product it must be fastened to the appliance prior
Download Pdf Manuals
Related Search