Manual - Proxxon Tools
Contents
1. Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord to carry the tools or pull the plug from an outlet Keep cord away from heat oil sharp edges or moving parts Replace damaged cords immediately Damaged cords increase the risk of electric shock When operating a power tool outside use an outdoor extension cord marked W A or W These cords are rated for outdoor use and reduce the risk of electric shock Personal Safety Stay alert watch what you are doing and use common sense when operating a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury ae Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Avoid accidental starting Be sure switch is off before plugging in Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents Remove adjusting keys or wrenches before turning the tool on A wrench or a key that is le2. the motor housing may cause electrical failures Do not alter or misuse tool Any alteration or modification is a misuse and may result in serious personal injury This product is not intended for use as a dental drill or in medical applications Serious personal injury may result REGLES DE SECURITE GENERALES AVERTISSEMENT Vous devez lire et comprendre toutes les instructions Le non respect m me partiel des instructions ci apr s entra ne un risque de choc lectrique d incendie et ou de blessures graves CONSERVEZ CES INSTRUCTIONS Aire de travail Veillez a ce que l aire de travail soit propre et bien clair e Le d sordre et le manque de lumi re favorisent les accidents N utilisez pas d outils lectriques dans une atmosphere explosive par exemple en presence de liquides de gaz ou de poussieres inflammables Les outils lectriques cr ent des tincelles qui pourraient enflammer les poussi res ou les vapeurs Tenez a distance les curieux les enfants et les visiteurs pendant que vous travaillez avec un outil lectrique Ils pourraient vous distraire et vous faire faire une fausse manoeuvre S curit lectrique Les outils mis a la terre doivent tre branches dans une prise de courant correctement install e et mise a la terre conform ment a tous les codes et reglements pertinents Ne modifiez jamais la fiche de quelque facon que ce soit par exemple en enlevant la broche de mise la terre N utilis
3. and the spinning bit Round material such as dowel rods pipes or tubing have a tendency to roll while being cut and may cause the bit to bite or jump toward you Clamping a small workpiece allows you to use both hands to control the tool Inspect your workpiece before cutting When cutting irregularly shaped workpieces plan your work so it will not slip and pinch the bit and be torn from your hand For example if carving wood make sure there are no nails or foreign objects in the workpiece Nails or foreign objects can cause the bit to jump Never start the tool when the bit is engaged in the material The bit cutting edge may grab the material causing loss of control of the cutter Avoid bouncing and snagging the wheel especially when working corners sharp edges etc This can cause loss of control and kick back If the workpiece or bit becomes jammed or bogged down turn the tool off by the switch Wait for all moving parts to stop and unplug the tool then work to free the jammed material If the switch of the tool is left on the tool could restart unexpectedly causing serious personal injury Do not leave a running tool unattended turn power off Only when tool comes to a complete stop it is safe to put it down Do not grind or sand near flammable materials Sparks from the wheel could ignite these materials Regularly clean the tool s air vents by compressed air Excessive accumulation of powdered metal inside
4. de mise en garde de le l outil Les meules et autres accessoires s ils tournent au dela de la vitesse nominale risquent d clater et de provoquer des blessures Tenez l outil par ses surfaces de prise isol es pendant toute op ration ou l outil de coupe pourrait venir en contact avec un cablage dissimul ou avec son propre cordon En cas de contact avec un conducteur sous tension les pieces m talliques a d couvert de l outil transmettraient un choc lectrique a l utilisateur Symbols Important Some of the following symbols may be used on your tool Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer Name Designation Explanation Volts Voltage potential Amperes Current Hertz Frequency cycles per second Watt Power Kilograms Weight Minutes Time Seconds Time Diameter Size of drill bits grinding wheels etc No load speed Rotational speed at no load Revolutions or reciprocation per minute Revolutions strokes surface speed orbits etc per minute Selector settings Speed torque or position settings Higher number means greater speed Infinitely variable selector Speed is increasing from narrow end Arrow Action in the direction of arrow Alternating current Type or a characteristic of current Class II construction Designates Double Insulated Constru
5. ProxxonTools com Manual LITA lp 3080767 Conforms to ANSI UL 60745 1 ANSI UL 745 1 ANSI UL 745 2 3 Certified to CAN CSA C22 2 No 60745 1 04 CAN CSA C22 2 No 745 1 CAN CSA C22 2 No 745 2 3 Fig 2 Fig 3 PROXXON LW E Dear Customer Before putting the machine into operation read the enclosed safety rules and operating instructions GENERAL SAFETY RULES Warning Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit Cluttered benches and dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control Electrical Safety Double Insulated tools are equipped with a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install a polarized outlet Do not change the plug in any way Double Insulation eliminates the need for the three wire grounded power cord and grounded power supply system
6. ction tools Legend Noise level may exceed 85 dB A during operation 1 Locking button Ear protection must be worn 2 Speed contol button Vibration at handle lt 2 5 m s 3 ON OFF switch 4 Hoop E Class Il Equipment Double Insulation 5 Connection cable with mains plug 6 Protective guard 7 Grinding disc Operation Functional Description The PROXXON Longneck Angle Grinder LW E is the ideal device for model making tool making and mould making and is also suitable for example for vehicle repairs It can be used for deburring roughing fine grinding chamfering paint removal rust removal cutting small components and sharpening tools It can be used on steel non ferrous metals glass wood and ceramics Flat gearhead manufactured from die cast aluminium Electronics for grinding speed control Technical Data Replacing the Grinding Disc Warning Disconnect the plug from the mains before replacing the grinding disc The grinding disc diameter must not exceed the specified size of 2 50mm Never press the locking button if the grinding disc is still rotating 1 Press the locking button 1 Fig 2 2 Turn the fastening screw 4 using an Allen key 5 until the locking button engages 3 Undo the fastening screw 4 remove the centring disc 3 and the grinding disc 2 4 Fit anew grinding disc Ensure the grinding disc is properly seated in the centring disc shoulder 5 Press the locking button 1 and tighten the fastening
7. dition that may affect the tools operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool SERVICE Tool service must be performed only by qualified repair personnel Service or maintenance performed by unqualified personnel could result in a risk of injury When servicing a tool use only identical replacement parts Follow instructions in the Maintenance section of this manual Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury Certain cleaning agents such as gasoline carbon tetrachloride ammonia etc may damage plastic parts SPECIFIC SAFETY RULES Accessories must be rated for at least the speed recommended on the tool warning label Wheels and other accessories running over rated speed can fly apart and cause injury Always use proper guard with grinding wheel A guard protects operator from broken wheel fragments Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord Contact with a live wire will make exposed metal parts of the tool live and shock the operator If cutting into existing walls or other blind areas where electrical wiring may
8. es outils de coupe doivent tre toujours bien aff t s et propres Des outils bien entretenus dont les ar tes sont bien tranchantes sont moins susceptibles de coincer et plus faciles a diriger Soyez attentif a tout d salignement ou coincement des pieces en mouvement a tout bris ou a toute autre condition pr judiciable au bon fonctionnement de l outil Si vous constatez qu un outil est endommag faites le r parer avant de vous en servir De nombreux accidents sont caus s par des outils en mauvais tat N utilisez que des accessoires que le fabricant recommande pour votre mod le d outil Certains accessoires peuvent convenir un outil mais tre dangereux avec un autre R PARATION La r paration des outils lectriques doit tre confi e a un r parateur qualifi L entretien ou la r paration d un outil lectrique par un amateur peut avoir des cons quences graves Pour la r paration d un outil n employez que des pi ces de rechange d origine Suivez les directives donn es la section R paration de ce manuel L emploi de pieces non autoris es ou le non respect des instructions d entretien peut cr er un risque de choc lectrique ou de blessures REGLES DE SECURITE SUPPLEMENTAIRES Utilisez toujours un protecteur de meule appropri Le protecteur arr te les clats en cas de bris de la meule Les accessoires doivent tre pr vus pour au moins la vitesse recommand e sur l tiquette
9. exist is unavoidable disconnect all fuses or circuit breakers feeding this worksite Always disconnect the power cord from the power source before making any adjustments or attaching any accessories You may unexpectedly cause tool to start leading to serious personal injury Be aware of the switch location when placing the tool down or when picking the tool up You may accidentally activate the switch Always wear safety goggles and dust mask Use the tool only in ventilated area Using personal safety devices and working in safe environment reduces risk of injury After changing the attachment or making any adjustments make sure the collet nut and any other adjustment devices are securely tightened Loose adjustment device can unexpectedly shift causing loss of control loose rotating components will be violently thrown Do not reach in the area of the rotating wheel The proximity of the rotating wheel to your hand may not always be obvious Carefully handle both the tool and individual grinding wheels to avoid chipping or tracking Install a new wheel if tool is dropped while grinding Do not use a wheel that may be damaged Fragments from a wheel that bursts during operation will fly away at great velocity possibly striking you or bystanders Use clamps to support workpiece whenever practical Never hold a small workpiece in one hand and the tool in the other hand while in use Allow for sufficient space between your hand
10. ez pas d adaptateur de fiche Si vous n tes pas certain que la prise de courant est correctement mise a la terre adressez vous a un lectricien qualifi En cas de d faillance ou de d fectuosit lectrique de Poutil une mise a la terre offre un trajet de faible r sistance l lectricit qui autrement risquerait de traverser l utilisateur Les outils double isolation sont quip s d une fiche polaris e une des lames est plus large que l autre qui ne peut se brancher que d une seule fa on dans une prise polaris e Si la fiche n entre pas parfaitement dans la prise inversez sa position Si elle n entre toujours pas bien demandez un lectricien qualifi d installer une prise de courant polaris e Ne modifiez pas la fiche de l outil La double isolation a limine le besoin d un cordon d alimentation a trois fils avec mise a la terre ainsi que d une prise de courant mise a la terre vitez tout contact corporel avec des surfaces mises a la terre tuyauterie radiateurs cuisini res r frig rateurs etc Le risque de choc lectrique est plus grand si votre corps est en contact avec la terre N exposez pas les outils lectriques la pluie ou a l eau La pr sence d eau dans un outil lectrique augmente le risque de choc lectrique Ne maltraitez pas le cordon Ne transportez pas l outil par son cordon et ne d branchez pas la fiche en tirant sur le cordon N exposez pas le cordon a la c
11. ft attached to a rotating part of the tool may result in personal injury Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the tool in unexpected situations Use safety equipment Always wear eye protection Dust mask non skid safety shoes hard hat or hearing protection must be used for appropriate conditions Tool Use and Care Use clamps or other practical way to secure and support the workpiece to a stable platform Holding the work by hand or against your body is unstable and may lead to loss of control Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Do not use tool if switch does not turn it on or off Any tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source before making any adjustments changing accessories or storing the tool Such preventive safety measures reduce the risk of starting the tool accidentally Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control Check for misalignment or binding of moving parts breakage of parts and any other con
12. haleur a des huiles a des ar tes vives ou a des pieces en mouvement Remplacez imm diatement un cordon endommag Un cordon endommag augmente le risque de choc lectrique 26 Lorsque vous utilisez un outil lectrique a l exterieur employez un prolongateur pour l ext rieur marqu W A ou W Ces cordons sont faits pour tre utilis s a l ext rieur et r duisent le risque de choc lectrique S curit des personnes Restez alerte concentrez vous sur votre travail et faites preuve de jugement N utilisez pas un outil lectrique si vous tes fatigu ou sous l influence de drogues d alcool ou de m dicaments Un instant d inattention suffit pour entra ner des blessures graves Habillez vous convenablement Ne portez ni v tements flottants ni bijoux Confinez les cheveux longs N approchez jamais les cheveux les v tements ou les gants des pieces en mouvement Des v tements flottants des bijoux ou des cheveux longs risquent d tre happ s par des pieces en mouvement M fiez vous d un d marrage accidentel Avant de brancher l outil assurez vous que son interrupteur est sur ARR T Le fait de transporter un outil avec le doigt sur la d tente ou de brancher un outil dont l interrupteur est en position MARCHE peut mener tout droit un accident Enlevez les cl s de r glage ou de serrage avant de d marrer l outil Une cl laiss e dans une pi ce tournante de l outil peut provoquer des bles
13. lean the unit thoroughly removing all grinding dust with a brush or a soft cloth Ensure all ventilation slots are free from obstruction The power cord shall be replaces by part no 38544 32 only if the cord is damaged Accessories Accessories available from PROXXON The following table shows you the recommended speed for different accessories supplied for your LW E Recommended Carborundum 28585 60 grit 13 000 rpm grinding disc 28586 36 grit 13 000 rpm Silicon Carbide 28587 60grit 10 000 rpm grinding disc Fan sander 28590 100 grit 12 000 15 000 rpm 28591 150 grit Corborundum 10 000 rpm bound cutting disc Warning Do not use the cutting disc for roughening work Risk of fracture
14. screw 4 Motor i Voltage 115 V Adjust the protective guard Power 1 8 hp 100 Watt Unit Warning Rotational speed 3300 up to 13000 Disconnect the plug from the mains before the rom following Disc diameter approx 2 50 mm 1 Release fastening screw 1 Fig 3 and turn the Length 11 13 32 290 mm protective guard to the desired position Weight approx 1 54 Ib 700g 2 Retighten the fastening screw Ensure the grinding Characteristic noise disc is properly seated in the centring disc emission lt 78 CB A shoulder 8 Using the unit Warning Injury hazard Do not work without a dust protection mask and protective goggles Do not use the unit on materials which contain asbestos 1 Switch the unit on via the switch 3 Fig 1 2 Use button 3 to set the unit speed to a speed appropriate for the work to be performed Note Do not press too hard when using the grinder Good grinding performance can only be achieved using the correct and constant rotational speed To achieve the best results when roughening apply the grinding disc to the grinding surface at an angle of between 30 and 40 and move evenly back and forth over the workpiece Do not bend the grinding disc into the cutting surface during cutting work Warning If the unit overheats switch it off and allow it to cool Maintenance Warning Disconnect the plug from the mains before performing any maintenance or cleaning work After use C
15. sures Ne vous penchez pas trop en avant Maintenez un bon appui et restez en quilibre en tout temps Un bonne stabilit vous permet de mieux r agir une situation inattendue Utilisez des accessoires de s curit Portez toujours des lunettes ou une visi re Selon les conditions portez aussi un masque antipoussi re des bottes de s curit antid rapantes un casque protecteur et ou un appareil antibruit Utilisation et entretien des outils Immobilisez le mat riau sur une surface stable au moyen de brides ou de toute autre fa on ad quate Le fait de tenir la pi ce avec la main ou contre votre corps offre une stabilit insuffisante et peut amener un d rapage de l outil Ne forcez pas l outil Utilisez l outil appropri la t che L outil correct fonctionne mieux et de fa on plus s curitaire Respectez aussi la vitesse de travail qui lui est propre N utilisez pas un outil si son interrupteur est bloqu Un outil que vous ne pouvez pas commander par son interrupteur est dangereux et doit tre r par D branchez la fiche de l outil avant d effectuer un r glage de changer d accessoire ou de ranger l outil De telles mesures pr ventives de s curit r duisent le risque de d marrage accidentel de l outil Rangez les outils hors de la port e des enfants et d autres personnes inexp riment es Les outils sont dangereux dans les mains d utilisateurs novices Prenez soin de bien entretenir les outils L
Download Pdf Manuals
Related Search