0845 683 8717 - Russell Hobbs
Contents
1. The points to pay attention during machine installation e Choose a suitable safe and level place to install your machine e Carry out the installation and connection of your machine by following the instructions e This machine should be installed and repaired by an authorised service only For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 5 Only original spare parts should be used with the machine Before installing be sure that the machine is unplugged Check whether the indoor electrical fuse system is connected according to the regulations All electrical connections must match the values indicated on the rating plate Pay special attention and be sure that the machine does not stand on the electricity supply cable Never use an extension cord or a multiple socket for making a connection The plug should be comfortably accessible after the machine has been installed After installing the machine to a suitable place run it unloaded for the first time In daily use This machine is for household use do not use it for any other purpose Commercial usage of the dishwasher will void the guarantee Do not load your machine above its capacity wash in the machine only those items which are suitable for dishwashing Do not get up sit or place a load on the open door of the dishwasher it may fall over Never put into the detergent and rinse aid dispensers of your machine anything other than th2. and End lights keep flashing e Water overflow alarm is active e Turn off your tap and contact an authorised service If the control light won t go out after a wash operation The Power On Off button is released yet If detergent residues are left in the detergent compartment Detergent has been added when the detergent compartment was wet For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 25 If water is left inside the machine at the end of the programme e The water drain hose is clogged or twisted e The filters are clogged e The programme is not finished yet If the machine stops during a wash operation Power failure e Water inlet failure e Program can be on standby mode If shaking and hitting noises are heard during a wash operation e Dishes placed incorrectly e Spray arm hitting the dishes If there are partial food wastes left on the dishes Dishes placed incorrectly into the machine sprayed water did not reach related places Basket overly loaded Dishes leaning against one another Very small amount of detergent added An unsuitable rather weak wash programme selected Spray arm clogged with food wastes Filters clogged Filters incorrectly fitted Water drain pump clogged If there are whitish stains on the dishes e Avery small amount of detergent is being used Rinse aid dosage setting at a very low level No special salt is being used desp
3. Russell Hobbs DISHWASHER INSTRUCTION MANUAL Model number RHDW1S Please read these instructions carefully and keep them for future reference For Customer Services Spare parts amp Warranty Information please call 0845 683 8717 Opening times Monday Friday 8am until 80m saturday amp Sunday 10am until 4pm Getting familiar with your machine ccccceeeeeeeeeneeeeeeeeeeeneeneeeeneneeneeesneees 4 amp echiical SPCCNCANONS 2isten essere we A seein ease heals 5 e Conformity with the standards and Test data c cece ccc e cece cent eee e ene 5 Safety information and RECOMMENAATIONS 111cececenecenceennecsnnssssssrsetesssssssssssseees D e REVCO oaea a a a a a AD Salely IMOMMAUOM aaa E 9 RecommMmendalons niesna Ea aes S N 6 e Items not suitable for dishwashing c0ccceeeee eee ee ee eee teens eens eaeeeeeeeaeeees 7 Installing the machine ssswiisic sen Sacanteen beens aedeaetaty ae voxt deni pieoceec yaad seta cvictsiesemeee 7 POSIMOMMG NE Machine carrs ra detach eater dened nus 7 e Water Connections eat centr ohne aint ialat cathe ran els hela 7 Waterinlet hose tiie A eat ae oases ee eae ata 8 Water OU MOSS ssscersccincsitnstscmnagangulacuniscnehl E O 8 Electrical cOnMe COM xscaswisa sigh cusiat aan eae each creates atu neuen E 9 e Fitting the machine undercounter cccccceeceeeeeeeeeeeeeeeeeeeeeaeeeeeeeaeaeeees 9 Porto U
4. in accordance with EN 50242 international norms d 12345 678 For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 19 PROGRAMME DESCRIPTIONS Programme items Programme Prewash Economic Quick oo names and No Heat 50T 60T temperatures Type of food Pre wash to coffee milk tea coffee milk tea soups sauces pasta aa Cena waste rinse and loosen cold meats cold meats eggs pilaf potato pilaf potato and residue awaiting vegetables not vegetables not and oven dishes fried even dishes i load then kept for long kept for long foods friad foods selecta programme A B Detergent A B amount A 25 cm A B 15 cm B 5 cm Electricity consumption kW hours Programme duration min Water 15 7 consumption liters Warning Short programs do not include a drying step The values declared above are the values obtained under laboratory conditions according to relevant standards These values can change depending on conditions of product s use and environment network tension water pressure water input temperature and environment temperature For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 20 SWITCHING ON THE MACHINE AND SELECTING A PROGRAMME Switching on the machine Press the Power On Off button z n aae Select the program suiting your C Russell Hobbs we dishes via the Pr
5. a Russell Hobbs Reset Intensive Wash Dry 65 C Prewash End Economy 50 C Start Pause 1 Power On Off Button When the Power On Off button is pressed the lamp on the Start Pause button starts lighting 2 Door Handle The door handle is used to open close the door of your machine 3 Start Pause Button Once you press the Start Pause button the programme you selected with the programme selector button will start running and the status indicator lamp wash Dry will light up In the stop condition while wash led is On Start Pause led will blink 4 Programme selector knob With the programme selector knob you can select a suitable programme for your dishes 5 Wash Dry End of cycle indicator You can monitor the programme status with the help of wash Dry and end indicators e Wash Dry e End Technical specifications Capacity sisnisvasnasteedeciasap seen 12 place settings PICION EEE EEA se toscss 845 mm Height without worktop 815 mm WIO ra an Vth cubes end oot ae 596 mm DG ei E A EE AE 598 mm Net Weight ceeee eee 46 kg Electricity input e 220 240 V 50 Hz Total POWGSl His itioaee cots 2200 W Heating Power 00e0e0e 2000 W Pump Power wiviescciauiea eetawnea ts 100 W Drain Pump Power 30 W Water supply pressur 0 03 MPa 0 3 bar 1 MPa 10 b
6. consumption Table of Water Hardness Level Settings Water German French British hardness hardness hardness hardness Hardness Level Indicator level Washi Dry lamp is on End lamp is off The Start Pause lamp is off Washi Dry lamp ts off End lamp is on The Start Pause lamp lamp is off Wash Dry lamp is off End lamp is off The start Pause lamp is on Wash Dry lamp is on End lamp is on The start Pause lamp is off Wash Dry lamp is on End lamp is off The start Pause lamp is on Wash Dry lamp is off End lamp is on The start Pause lamp is on If the hardness of the water you use is above 90 dF French hardness or if you are using well water you are recommended to use filter and water refinement devices NOTE Hardness level is adjusted to level 3 as a factory setting For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 12 Adjusting salt consumption Adjust the water softener according to how hard your tap water is po UO ee Rese h Wash Dry peeve Prewash 4 End Quick Quick 60 C 40 C Russell Hobbs e D sc aD Move the programme selector knob to the 0 Reset position while your machine is not in operation After resetting your machine press the Start Pause button and keep it pressed down Meanwhile energise the machine by pressing the Power On Off button P Keep Start
7. e f such detergents are in the form of tablets never put them into the interior section or the cutlery basket of the dishwasher Always put the tablets into the detergent compartment in the detergent dispenser e They produce good results for certain types of usage only If you are using this type of detergents you need to contact the manufacturers and find out about the suitable conditions of use e When the conditions of use of such products and the machine settings are appropriate they ensure savings in salt and or rinse aid consumption e Contact the detergent manufacturers if you are not obtaining good wash results if your dishes stay calcareous and wet after having used 2 in 1 or 3 in 1 detergents The scope of warranty for your machine does not cover any complaints caused by the use of these types of detergents Recommended usage If you want to obtain better results while using combined detergents add salt and rinse aid into your machine and adjust the water hardness setting and the rinse aid setting to the lowest position Solubility of the tablet detergents produced by different companies can vary depending on the temperature and time Therefore it is not recommended to use such detergents in short programs It is more suitable to use powder detergents in such programs Warning Should any problem which you have not encountered before arise with the use of this type of detergents contact the detergent manufacturers direct
8. DOIN CASE OF FAILURE ERROR CODE ERROR CONTROL Wash Dr DESCRIPTION Make sure the water input tap is totally open and that there is no water cut Close the water input tap separate the water input hose from the tap and clean the filter at the connection end of the hose Restart your machine contact the service if the error resumes Close the tap Inadequate water supply Error of continuous water input Contact the service Water discharge hose is clogged The waste water in the machine cannot be The filters of your machine might be clogged discharged Power off on your machine and activate the program cancellation command If the error continues contact the service Intended water temperature could not Contact the service be reached faulty heater and heater sensor Alarm is active against Power off your machine and close the tap water overflow Contact the service Faulty electronic card Contact the service If one of program monitor lights is on and the start Pause light flashes on and off Your machine s door is open shut the door If the programme won t start Check if the plug is connected Check your indoor fuses Be sure that the water inlet tap is turned on Be sure that you have closed the machine door Be sure that you switched off the machine by pressing the Power On Off button Be sure that the water inlet filter and the machine filters are not clogged If the Wash Dry
9. Pause keys press until program monitor lights are on and off After the lamps Wash Dry End have flashed j release the Start Pause button Your machine displays the latest entered water hardness setting You can adjust the levels by pressing the Start Pause button amp according to Table of Water Hardness Level Settings After adjusting the water hardness level press on off button to save the settings in memory For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 13 Detergent usage Use a detergent specifically designed for use in domestic dishwashers You can find powder gel and tablet detergents in the market that have been designed for household dishwashers Detergent should be put into the compartment prior to starting the machine Keep your detergents in cool dry places out of reach of your children Do not fill detergent into the detergent compartment more than required otherwise it may cause scratches on your glasses as well as lead to a poorly dissolved detergent Should you need more information concerning the detergent you will use contact detergent manufacturers directly Filling the detergent compartment Push the latch to open the detergent container as shown in the image The Detergent pod has level lines inside It is possible to measure the right detergent amount using these lines The Detergent pod can take a maximum of 40 cm of detergent Open the dis
10. SING themachne sxkc5 snsoesttet cess aa sean baadielinanaay anus weed nies 11 Preparing the machine for USC 2 2ccccceccecsenscescencenceneeneensnessnenceneeneesenaneneeneaees 11 e The importance of water decalcification ccecceeec eee eeeeeeeeeeeeeeeeeeneeneees 11 s SPADO WIN Sae a neat a ada ctancnelte Gag Sates enashtel caaat 11 TESS ee a E ta tel cednt smells queen en ean EES 12 e Adjusting salt CONSUMPU OM ixcdetccedonevealerdewnckleconceiatantelds ower ere aeelde dau 12 Deroo USAC ninn A a tise ae eee 14 e Filling the detergent compartment ccceeeee eee eect ee eee eee eee eee eae eae rnn 14 Combined Celerant eroriren bnie ii aT tea iwal ep hauadaw eai 14 e Filling with rinse aid and making the Setting cccceeeeeeeeeeeeeeeeeeeeeeeeeees 15 For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 1 Loading your dishwashef sikh i icoxteetsacbntcxasavastzetsenatanatiedaelcaastesnedeniaresivateaeanoere DISPIACE niran a aeaa a a a a E ASR e Alternative basket loadS ssnnnnnnnnrrrrrrnunrrrrerrrrrrrrerrerererersreresersssrsreresseessresss e Standard loading and Test data es eor aE E A A EE AE E Programme descriptions sses a naaa AEE EENE Programme WINS cnra a a A a aA Switching on the machine and selecting a PrOGrarmmmMe 11 0ceeceenereneeeeeeeeeseseensnssneaes e Switching on the machine ssseseessenssnnssres
11. after putting salt then run a short washing program with an empty machine in order to avoid any damage to prevent corrosion to your machine due to the salt overflow while filling in the salt container For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 11 In order to understand whether or not the amount of softener salt in your machine is sufficient check the transparent section on the salt compartment cap There is sufficient salt if the transparent section is green Salt has to be added if the transparent section is not green Testing strip The washing effectiveness of your machine depends on the softness of the tap water For this reason your machine is equipped with a system that reduces the hardness in mains water supply The washing effectiveness will increase when the system is correctly set To find out the water hardness level of water in your area contact your local water board or determine water hardness level by using the test strip if available Open the Run Keep the Shake the Wait for Make your machine s water hardness testing water testing testing strip 1 min setting according to the result obtained strip through strip in after taking it through the testing strip your tap water for 1 out of water for 1 Sec Level 1 No Lime Level 2 Very low lime content Level 3 Low lime content Level 4 Medium lime content Level 5 Lime content Level 6 High lime content Adjusting salt
12. ar CUNEN reesei ada eR 10A e Producer company has its right to amend design and technical specifications reserved e The machine s service life is 10 years the duration required to keep spare parts for the machine to fulfil its usage functions Conformity with the standards and Test data EC Declaration of Conformity All stages related to the machine are executed in accordance with the safety rules provided in all relevant directives of the European Community 2004 108 EC 2006 95 EC IEC 436 DIN 44990 EN 50242 SAFETY INFORMATION AND RECOMMENDATIONS Recycling e Certain components and the packaging of your machine have been produced from recyclable materials Plastic parts are marked with international abbreviations gt PE lt gt PS lt gt POM lt g lt gt PP lt e Cardboard parts have been produced from recycled paper and they should be disposed of into waste paper collection containers for recycling e Such materials are not suitable for being disposed of into garbage bins They should be delivered to recycling centres instead e Contact relevant centres in order to obtain information on methods and points of disposal Safety Information When you take delivery of your machine e Check for any damage to your machine or to its packaging Never start a machine damaged in any way make sure to contact an authorised service e Unwrap the packaging materials as indicated and dispose of them in accordance with the rules
13. cal connection The earthed plug of your machine should be connected to an earthed outlet supplied by suitable voltage and current If there is no earthing installation have a competent electrician carry out an earthing installation In case of usage without earthing installed our company will not be responsible for any loss of usage that might occur At low voltage Wash efficiency of your machine decreases Always use the coated plug supplied with your machine The machine s electrical cable should be replaced by an authorised service or an authorised electrician only Failure to do so may lead to accidents For safety purposes always make sure to disconnect the plug when a wash programme is finished In order not to cause an electric shock do not unplug when your hands are wet When disconnecting your machine from the mains supply always pull from the plug Never pull the cord itself Fitting the machine undercounter If you wish to fit your machine undercounter check whether you have sufficient space under your countertop and whether the wiring plumbing is suitable to do so J If you decide that the space under the countertop is suitable for fitting your machine remove the worktop as shown in the illustration Warning The stand part which will settle the machine under it by removing its worktop has to be stable in such a way not to allow balance disorder To remove the worktop remove the screws that hold the worktop which are lo
14. can be seen from across Never use your dishwasher without any filter e Incorrect fitting of the filter will reduce the washing effectiveness e Clean filters are very important in terms of the proper running of the machine For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 23 Spray arms Check whether or not the holes for the upper and lower spray arms are clogged If there is any clogging remove the spray arms and clean them under water You can remove the lower spray arm by pulling it upwards while the upper spray arm nut can be removed by turning the nut to the left Be sure that the nut is perfectly tightened when refitting the upper spray arm Hose filter Water is prevented by the inlet hose filter so as to avoid any damage to your machine because of any contamination sand clay rust etc that might be occasionally carried in through the mains water supply or the indoor plumbing and to forestall such complaints as yellowing and formation of deposits after washing Check the filter and the hose from time to time and clean them if necessary To clean the filter first turn off your tap and then remove the hose After removing the filter from the hose clean it under the tap Insert the cleaned filter back into its place inside the hose Refit the hose For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 24 FAILURE CODES AND WHAT TO
15. cated at the rear of the machine then push the front panel 1 cm from the front side towards the rear and lift it For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 9 Adjust the machine feet according to the slope of the floor Fit your machine by pushing it undercounter without letting the hoses get crushed or bent Warning After removal of worktop the machine should be placed in such a closed place of which dimensions are shown at fig For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 10 Prior to using the machine for the first time e Check whether the electricity and supply water specifications match the values indicated by the installation instructions for the machine e Remove all packaging materials inside the machine e Set the water softener e Add 2 kg salt into the salt compartment and fill with water up to a level at which it will almost overflow e Fillthe rinse aid compartment PREPARING THE MACHINE FOR USE The importance of water decalcification For a good washing function the dishwasher needs soft i e less calcareous water Otherwise white lime residues will remain on the dishes and the interior equipment This will negatively affect your machine s washing drying and shining performance When water flows through the softener system the ions forming the hardness are removed from the water a
16. e machine 5 Operate the machine after it is completely full 6 Use pre washing program only when necessary 7 Observe program information and average consumption values table when selecting a program 8 Since the machine will reach high temperatures it should not be mounted near refrigerator 9 Ifthe appliance is located in a place where the risk of freezing exists you must completely drain the water that has remained in the machine Turn off the water tap disconnect the water inlet hose from the tap and allow the interior water to drain For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 2 For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 Opening times Monday Friday 8am until 8pm Saturday amp Sunday 10am until 4pm Customer Service Department Picktree Court Picktree Lane Chester le Street Co Durham DH3 3SY Revision 1 CE H This symbol is known as the Crossed out wheelie bin Symbol When this symbol is marked on a product batteries it means that the product batteries should not be disposed of with your general household waste Only discard electrical electronic battery items in separate collection schemes which cater for the recovery and recycling of materials contained within Your co operation is vital to make sure the success of these schemes and for the protection of the environment For your nearest disposal facility visit
17. hwasher detergent and pour into the larger ee E25 cm if your dishes are heavily soiled or 15 if they are less soiled A If your dishes have been kept dirty for a very long time if there are dried food wastes on them and if you have overly loaded the dishwasher pour 5cm detergent into the pre wash compartment and start your machine You may have to add more detergent into your machine depending on the degree of soil and on the water hardness level in your area Combined detergents Detergent manufacturers also manufacture combined detergents that are called 2 in 1 3 in 1 5 in 1 The 2 in1 detergents contain detergent salt or rinse aid While using the 2 in 1 detergents it should be observed which functions the tablet consists of The other tablet detergents also have detergent rinse aid salt various extra functions Generally combined detergents produce sufficient results under certain usage conditions only Such detergents contain rinse aid and or salt in preset amounts Points to consider when using this type of products e Always make sure to check the specifications of the product you will use or whether or not it is a combined product e Check if the detergent used is appropriate for the hardness of mains water that machine is appertaining to e Observe the instructions on packagings when using such products For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 14
18. ill face down e You are recommended not to load into your machine any dishes different or more than indicated Items not suitable for dishwashing e Cigarette ash candle wax polish chemical substances iron alloy materials e Forks spoons and knives with wooden bone or ivory or nacre coated handles glued items paint items soiled with abrasive acidic or base chemicals Plastic items that are not heat resistant copper or tin coated containers e Aluminium and silver objects they may discolour become dull e Certain delicate glass types porcelains with ornamental printed patterns as they fade even after the first wash certain crystal items as they lose their transparency over time adhered cutlery that is not heat resistant lead crystal glasses cutting boards items manufactured with synthetic fibre e Absorbent items as sponges or kitchen rags are not suitable for dishwashing Warning Take care to buy dishwasher proof sets in your future purchases INSTALLING THE MACHINE Positioning the machine When determining the place to put your machine on take care to choose a place where you can easily load and unload your dishes Do not put your machine in any location where there is the probability for the room temperature to fall below 0 C Before positioning take the machine out of its packaging by following the warnings located on the package Position the machine close to a water tap or drain You need to site you
19. ite the high degree of water hardness Water softener system setting is at a very low level Salt compartment cap not closed well If the dishes won t dry up e A programme without a dry operation selected e Rinse aid dosage set too low e Dishes unloaded too fast If there are rust stains on the dishes e Stainless steel quality of the dishes washed is insufficient High rate of salt in the wash water Salt compartment cap not closed well Too much salt spilt into the sides and into the machine while filling it with salt Unhealthy mains grounding Call an authorised service if the problem still persists after the controls or in case of any malfunction not described above Please see the back page at the instruction manual For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 26 PRACTICAL AND USEFUL INFORMATION When not operating your machine Unplug the machine and then turn the water off Leave the door slightly ajar in order to prevent the formation of unpleasant smells Keep the machine interior clean oe 8 unt Eliminating water droplets Wash the dishes with the intensive programme Take all of the metal containers in the machine out Do not add detergent e een 3 If you properly place your dishes into the machine you will be using it in the best way in terms of energy consumption washing and drying performance 4 Clean all rough waste before you place dirty dishes to th
20. ly When you give up using combined detergents Fill the salt and rinse aid compartments Adjust the water hardness setting to the highest position and run an empty wash Adjust the water hardness level Make the suitable rinse aid setting Filling with rinse aid and making the setting Rinse aid is used to prevent the stay of white water drops lime stains white film strio shaped stains that may form on the dishes as well as to increase the drying performance Contrary to the popular beliefs it is used not only for obtaining shinier dishes but also for obtaining sufficiently dried dishes For this reason care should be taken that there is adequate amount of rinse aid in the rinse aid compartment and only polishing material produced for use at dishwashers should be used To put rinse aid remove the rinse aid compartment cap by turning it J Fill the rinse aid compartment with rinse aid until the rinse aid level indicator becomes dark refit the cap and close it by turning it ina way that the nails will correspond to one another By checking the rinse aid level indicator on the detergent dispenser you can understand whether or not your machine needs rinse aid A dark indicator I means that there is rinse aid in the compartment while a light indicator shows that you need to fill the compartment with rinse aid For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 15 The rinse aid level adjus
21. machine s packaging make sure that the packaging material is out of reach of children Do not allow children to play with or start the machine Keep your children away from detergents and rinse aids Keep children away from the machine while it is open because there may still be residues of cleaning substances inside the machine Be sure that your old machine does not pose any threat to your children Children are known to have gotten themselves locked in old machines To forestall such a situation break your machine s door lock and tear off the electrical cables In case of malfunctioning Any malfunction in the machine should be repaired definitely by qualified persons Any repair work performed by anyone other than the authorised service personnel will cause your machine to be left outside the scope of warranty Prior to any repair work on the machine be sure that the machine is cut off from the mains Switch off the fuse or unplug the machine Do not pull by the cable when unplugging Make sure to turn off the water tap For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 6 Recommendations For energy and water saving remove coarse residues on your dishes before placing the dishes into the machine Start your machine after having fully loaded it e Use the pre wash programme only whenever necessary e Place such hollow items as bowls glasses and pots into the machine in such a way that they w
22. nd the water reaches the softness required to obtain the best washing result Depending on the level of hardness of the inflowing water these ions that harden the water accumulate rapidly inside the softener system Therefore the softener system has to be refreshed so that it operates with the same performance also during the next wash For this purpose dishwasher salt is used Filling with salt Only if detergent tablet or gel does not have salt contained in them Use softener salt specifically produced for use in dishwashers To put softener salt first remove the lower basket and then open the salt compartment cap by turning it counter clockwise At first fill the compartment with 2kg salt and water at overflowing _ level If available using the funnel 4 provided will make filling easier refit the cap and close it After every 20th 30th wash add salt into your machine until it fills up approx 1 5 kg Fill the salt compartment with water at first use only We recommend that you use small grained or powder softener salt Do not put table salt into your machine Otherwise the function of the softener compartment may decrease over time When you start your dishwasher the salt compartment gets filled with water Therefore put the softener salt prior to starting your machine This way overflowing salt gets immediately cleaned up through the wash operation If you are not going to wash any dishes immediately
23. nt without loading any dishes into the machine select a programme that runs at high temperature and start the machine In case of insufficiency use special cleansing material available in the market Cleansing material produced special to machines by detergent producers Cleaning the seals in the machine door To clean any accumulated residues in the door seals wipe the seals regularly by using a dampened cloth Cleaning machine Clean the filters and spray arms at least once a month Unplug your machine and turn off its tap before starting the cleaning Do not use hard materials when cleaning your machine Wipe with a fine cleaning material and a dampened cloth Filters Check if any food wastes have remained on the coarse and fine filters If any food wastes are left remove the filters and clean them thoroughly under the water tap a Micro Filter b Coarse Filter c Metal Plastic Filter To remove and clean the filter combination turn it counter clockwise and take it out by lifting upwards J Pull and remove the metal plastic filter Then pull the coarse filter out of the micro filter Rinse it with lots of water under the tap Refit the metal plastic filter Insert the coarse filter into the micro filter ina way that the marks will correspond to one another Attach micro filter into the s4 W N metal plastic filter and turn to the direction of arrow and it is locked when the arrow on micro filter
24. o cancel a program while a washing program is resumed Turn the Program Selection Button to Reset Press the Power Start Pause button rewasi The program will have been cancelled once the drying lamp goes off and the end light is on The machine will discharge the Press the Power ac water in it for 30 sec approximately Start Pause button Switching the machine off Pull the plug out of the outlet Turn of the water tap When the lamp End lights up switch your machine off by using the Power On Off button rewas Note You can slightly open the door in order for the machine to perform a faster dry operation after the wash programme is finished Note If the machine door opens during washing or the power is cut off the machine will go back to the program if the door is shut or the power is put back on Note lf energy is cut or machine door is opened during drying process program is terminated Your machine becomes ready for new program selection For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 22 MAINTENANCE AND CLEANING Cleaning the machine at regular intervals prolongs the machine s service life Oil and lime may accumulate in the machine s washing section In case of such accumulation Fill the detergent compartme
25. ogram Selection button Start the program pressing the Power Start Pause button Once the Power On Off key is pressed the lamp Power Start Pause is highlighted The lamp on Program Start Pause button goes off once the Program starts and the washing Drying lamp is highlighted Program follow up You can follow the program flow using the program follow up lambs located on the control panel Do not open the cover before the lamp Finished is on As long as Washing and Drying goes on the Washing Drying lamp is lit When drying is active the machine stays silent about 40 50 minutes Once the program is over the End light is illuminated Changing a programme If you would like to change programs while a washing program is continuing The new program started will resume the course of the old program After the program stops select your desired program via the Program selection button Start the program you have newly selected by pressing again the Start Pause key Press the Power Start Pause key Reset Prewash Quick S Quick pf ice ic tic Economy Start Pause For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 21 Changing a programme with resetting If you would like t
26. ose detergents and rinse aids which are produced specifically for dishwashers Our company will not be responsible for any damage that might occur in your machine otherwise The water in the machine s washing section is no drinking water do not drink it Due to danger of explosion do not put into the machine s washing section any chemical dissolving agents such as solvents Check whether plastic items are heat resistant before washing them in the machine Do not put into your machine those items which are not suitable for dishwashing Also do not fill any basket above its capacity Our company will not be responsible for any scratch or rust to form on the inner frame of your machine due to basket movements otherwise Especially because hot water may flow out the machine door should not be opened under any circumstances while the machine is in operation In any case a safety devices ensures that the machine stops if the door is opened Do not leave your dishwasher s door open Failure to do so may lead to accidents Place knives and other sharp ended objects in the cutlery basket in blade down position This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety For your children s safety After removing the
27. other You are recommended to use the cutlery grid in order to obtain the best result To avoid any possible injuries always place such long handle and sharp pointed dishes as serving fork bread knife etc with their sharp points facing down or horizontally on the baskets Warning Place your dishes into your machine in a way that they will not prevent the upper and lower spray arms from spinning Dish rack There are dish racks on the upper basket of your machine A fj You can use these dish racks in open or closed position When they are in open position A you can place your cups on them and when in closed position ff you can place long glasses on the basket Also you can use these racks by placing long forks knives and spoons on them laterally For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 16 Top basket height adjustment while it is full The Basket height adjustment mechanism on the top basket of your machine is designed to let you adjust the height of your top basket upwards or downwards without removing it from your machine when it is full and create large spaces at the top or bottom area of your machine as needed The Basket of your machine is set to upper position as a detault setting In order to raise your basket hold it on both sides and pull it upwards In order to lower it hold it from both sides again and leave it When loading the upper adjustable basket make sure tha
28. r machine taking into consideration that its connections will not be altered once they are made Do not grip the machine by its door or panel in order to move it Take care to leave a certain clearance from all sides of the machine so that you can comfortably move it back and forth during cleaning Make sure that the water inlet and outlet hoses do not get squeezed while positioning the machine Also make sure that the machine does not stand on the electrical cable Adjust the machine s adjustable feet so that it can stand level and balanced Proper positioning of the machine ensures problem free opening and closing of its door If the door of you machine does not close properly check if the machine is stable on the floor it stands if not adjust the adjustable feet and ensure its stable position For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 7 Water connection Be sure that the indoor plumbing is suitable for installing a dishwasher Also we recommend that you fit a filter to the water pipe or tap so as to avoid any damage to your machine because of any contamination sand clay rust etc that might be occasionally carried in through the mains water supply or the indoor plumbing and to forestall such complaints as yellowing and formation of deposits after washing Water inlet hose Do not use the water inlet hose of your old machine or of any other machine Use the new water inlet hose
29. suessresressrerrrrssresressrrrrsreseessreern e Programme TONMOW UD tase s 522524 e isin a oane da tuner baosue dele veaeicareug delve any e Chanana a programme sii 2nccuseteeenceinsce E nedaus tags teuae bares e Changing a programme with resetting ccccee eee ee ee ee eect ee eeeeeeaeeeeeeeeeaeneees CSWICHING INE machhe Oee oh te ce sae a ae aera cage wads toad cle ee Maintenance and Cleaning 1cccccccccccccnsnnnnnnnnnnnsecnenenensesesessnsnsnnnananensnnsesesssesnessnenssnsnsaanaes FINES oea a I a e S E E ATES Spay aS eiia e AEAEE AN E E THOSCTING esner ear a a e E T E E Failure codes and what to do in case of failure ccececeeeeeeeeeeeeeeeeeeeeeeeeeenees Practical and useful INFOFIMATION 2 2 1 1c2ccecenenceeeeeneeneeeenseenneneeneneensaseaensensneenseneanaees For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 2 16 17 19 23 23 24 24 25 1 Worktop 7 Rating plate 2 Upper basket with racks 8 Control Panel 3 Upper spray arm 9 Detergent and rinse aid dispenser 4 Lower basket 10 Cutlery basket 5 Lower spray arm 11 Salt dispenser 6 Filters 12 Upper basket adjustable track latch For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 3 Z428 89 SPBO ed eseald UOIeWJOjU AULEM 3 SHEd aIedS samas J WOI SND 104 GETTING FAMILIAR WITH YOUR MACHINE 5 OOO U UOU
30. supplied with your machine instead If you are going to connect a new or long unused water inlet hose to your machine run water through it for a while before making the connection Connect the water inlet hose directly to the water inlet tap The pressure supplied by the tap should be at a minimum of 0 03 Mpa and and at a maximum of 1 Mpa If the water pressure is above 1 Mpa a pressure relief valve should be fitted inbetween After the connections are made the tap should be turned on fully and checked for water tightness For the safety of your machine make sure to always turn off the water inlet tap after each wash programme is finished NOTE Aquastop water spout is used in some models In case of using Aquastop a dangerous tension exists Do not cut Aquastop water spout Do not let it get folded or twisted Water outlet hose The water drain hose can be connected either directly to the water drain hole or to the sink outlet spigot Using a special bent pipe if available the water can be drained directly into the sink via hooking the bent pipe over the edge of the sink This connection should be at a minimum of 50 cm and and at a maximum of 110 cm from the floor plane Warning When a drain hose longer than 4 m is used the dishes might remain dirty In that case our company will not accept responsibility For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 8 Electri
31. t both sides of the mechanism are in the same position up or down Lower Basket Folding Racks Folding racks consisting of two parts that are located on the lower basket of the machine are designed in order to let you place big items easier such as pots pans etc If required each part can be folded separately or all of them can be folded and larger spaces can be obtained You can use folding racks by raising them upwards or by folding Goblet clamp It enables the safe washing of your goblets with long foot and stems Do not lean your long glasses on one another this way they can not remain stable and can be damaged during washing To create wide spaces when you do not want to use goblet clamp turn to position For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 17 Alternative basket loads Lower Basket Top basket a T 3p fi 4 eam wr ies te Wy Faulty loads For Customer Services Spare Parts amp Warranty Information please call 0845 683 8717 18 Standard loading and test data Capacity Upper and lower baskets 12 place settings The upper basket should be adjusted to high position Cups should be placed on to the dish rack pins Detergent Rinse aid 5 25 cm in accordance with EN50242 DIN 44990 IEC 436 international norms Rinse aid dosage adjustment 4 Programme test Economic 50 C
32. ter can be set to a position between 1 and 6 Factory setting for rinse aid is the position 3 You need to increase the degree of the adjuster if water stains form on your dishes after a nag whereas you need to decrease the degree if a blue stain is left when wiped by hand Warning Use only those rinse aid materials which are allowed for use in the machine As rinse aid residues left as a result of overflowing will create extremely high amounts of foam and thus reduce the washing performance remove the excess amount of rinse aid by wiping it with a rag LOADING YOUR DISHWASHER If you properly place your dishes into the machine you will be using it in the best way in terms of energy consumption washing and drying performance There are two separate baskets for you to load your dishes into your machine You can load round and deep items as pots with long handles pot lids plates salad plates cutlery sets In to the lower basket The upper basket has been designed for tea plates dessert plates salad bowls cups and glasses When placing long stem glasses and goblets lean them against the basket edge rack or glass supporter wire and not against other items Do not lean long glasses against one another or they will not remain steady and may be damaged lt is more appropriate to locate the thin narrow parts into the middle sections of baskets You can place spoons among the other cutlery sets in order to prevent them from sticking to one an
33. www recycle more co uk or ask in store for details We reserve the right due to possible changes to design to alter the instruction manual without prior notice 52036454
Download Pdf Manuals
Related Search