Home

MAXIMA - Pride Mobility Products

1. Stand at side of your scooter Push down on the seat rotation lever and rotate the seat until it is facing you Make certain that the seat is fixed securely in position Position yourself comfortably and securely in the seat Push down on the seat rotation lever and rotate the seat until you are facing forward Make certain that the seat is fixed securely in position Make certain that your feet are safely on the floorboard PRE RIDE ADJUSTMENTS AND CHECKS Is the seat at the proper height Is the seat fixed securely in place Is the tiller at a comfortable setting and locked securely in place See VI Comfort Adjustments Is the key fully inserted into the key switch and turned clockwise to the position See Your Scooter Does the scooter s horn work properly Is your proposed path clear of people pets and obstacles Have you planned your route to avoid adverse terrain and as many inclines as possible 2 OPERATING YOUR SCOOTER WARNING The following can adversely affect steering and stability while operating your scooter m Holding onto or attaching a leash to walk your pet N Carrying passengers including pets Hanging any article from the tiller 4 Towing or being pushed by another motorised vehicle WARNING Keep both hands on the tiller and your feet on the floorboard at all times while operating your scooter This driving position gives you th
2. gt i 21 Healey Road Dandenong 3175 Victoria Australia ACN 088 609 661 SAFETY GUIDELINES WARNING An authorised Pride Provider or qualified technician must perform the initial setup of this scooter and must perform all of the procedures in this manual The symbols below are used throughout this owner s manual and on the scooter to identify warnings and important information It is very important for you to read them and understand them completely WARNING Indicates a potentially hazardous condition situation Failure to follow designated procedures can cause either personal injury component damage or malfunction On the product this icon is represented as a black symbol on a yellow triangle with a black border MANDATORY These actions should be performed as specified Failure to perform mandatory actions can cause personal injury and or equipment damage On the product this icon is represented as a white symbol on a blue dot with a white border PROHIBITED These actions are prohibited These actions should not be performed at any time or in any circumstances Performing a prohibited action can cause personal injury and or equipment damage On the product this icon is represented as a black symbol with a red circle and red slash Please fill out the following information for quick reference Pride Provider Address Phone Number Purchase Date Serial Number NOT
3. Removal of grounding prong can create electrical hazard If necessary properly install an approved 3 pronged adapter to an electrical outlet having 2 pronged plug access Do not connect an extension lead to the AC DC converter or the battery charger Maxima www pridemobility com 2 11 SAFETY GENERAL MANDATORY Do not operate your new scooter for the first time without completely UY reading and understanding this owner s manual Your scooter is a state of the art life enhancement device designed to increase mobility Pride provides an extensive variety of products to best fit the individual needs of the scooter user Please be aware that the final selection and purchasing decision regarding the type of scooter to be used is the responsibility of the scooter user who is capable of making such a decision and his her healthcare professional 1 medical doctor physical therapist etc The contents of this manual are based on the expectation that a mobility device expert has properly fitted the scooter to the user and has assisted the prescribing healthcare professional and or the authorised Pride Provider in the instruction process for the use of the product There are certain situations including some medical conditions where the scooter user will need to prac tice operating the scooter in the presence of a trained attendant A trained attendant can be defined as a family member or care professional spe
4. WARNING Failure to ensure that axle key is properly installed into axle slot when 6 Reinstall the drive wheel nut and washer onto the axle and tighten N WARNING sure both the nut and washer are reinstalled and tightened properly a 7 Remove the blocks from beneath the scooter 36 www pridemobility com Maxima IX CARE AND MAINTENANCE WIRING HARNESSES Regularly check all wiring connections Regularly check all wiring insulation including the charger power lead for wear or damage Have your authorised Pride Provider repair or replace any damaged connector connection or insula tion that you find before using your scooter again for ingress of liquids you should keep electrical connections away from sources of dampness including direct exposure to water or bodily fluids and incontinence Check PROHIBITED Even though the scooter has passed the necessary testing requirements S electrical components frequently for signs of corrosion and replace as necessary ABS PLASTIC SHROUDS The front tiller shroud front shroud and the rear shroud are formed from durable ABS plastic and are coated with an advanced formula urethane paint A light application of car wax will help the shrouds retain their high gloss LIGHT BULB REPLACEMENT The scooter s light bulbs are easily replacable Do not use regular automotive type 12 volt light bulbs your scooter is equipped with a 24 volt electrical syste
5. the lever to move in reverse When the throttle control lever is completely released it automatically returns to the centre stop position and engages your scooter s brakes Battery Condition Meter When the key is fully inserted and turned clockwise to power up your scooter this meter indicates the approximate battery voltage strength For further information on battery charging see IV Batteries and Charging Horn Buttons These buttons activate a warning horn The key must be inserted and turned clockwise for the horn to be operational Do not hesitate to use the warning horn when its use could prevent accident or injury Light Switch This switch controls your scooter s lighting system Toggle this switch to turn on and turn off the lights WARNING Scooter users are required to use their lights when visibility is restricted day or night Turn Indicator Buttons Use these buttons to turn on the left and right turn indicator lights Press the appropriate turn indicator button once to activate it Your scooter s turn indicators are timed to shut off automatically Hazard Lights Switch This switch activates the 4 way flashers on your scooter Toggle this switch to turn on and turn off the lights Off board Charger Port The scooter s off board charger plugs into this port 16 www pridemobility com Maxima YOUR SCOOTER REAR SECTION The manual freewheel lever the
6. Disconnect the batteries from the scooter Store your scooter in a warm dry environment Avoid storing your scooter where it will be exposed to temperature extremes WARNING Always protect batteries from freezing temperatures and never charge frozen battery Charging a frozen battery may result in damage to the battery Batteries that are regularly and deeply discharged infrequently charged stored in extreme temperatures or stored without a full charge may be permanently damaged causing unreliable performance and limited service life It is recommended that you charge the scooter batteries periodically throughout periods of prolonged storage to ensure proper performance You may wish to place several boards under the frame of your scooter to raise it off of the ground during periods of prolonged storage This takes the weight off the tyres and reduces the possibility of flat spots developing on the areas of the tyres contacting the ground DISPOSAL OF YOUR SCOOTER Your scooter must be disposed of according to applicable local and national statutory regulations Contact your local waste disposal agency or authorised Pride Provider for information on proper disposal of pack aging metal frame components plastic components electronics batteries neoprene silicone and poly urethane materials 38 www pridemobility com Maxima WARRANTY TWO YEAR LIMITED WARRANTY Structural frame components including platform
7. Please observe the following safety tips when getting onto and off of your scooter Remove the key from the key switch Ensure that your scooter is not in freewheel mode See Your Scooter Make certain that the seat is fixed into place Flip up the armrests to make getting on and off the scooter easier WARNING Position yourself as far back as possible in the scooter seat to prevent the scooter from tipping WARNING Avoid putting all your weight on the scooter armrests and do not use the armrests for weight bearing purposes such as transfers Such use may cause the scooter to tip resulting in a fall from the scooter and or personal injury WARNING Avoid putting all of your weight on the floorboard Such use may cause the scooter to tip REACHING AND BENDING Avoid reaching or bending while driving your scooter Bending forward creates the risk of accidental throttle control lever contact Bending to the side while seated creates the risk of tipping It is important to maintain a stable centre of gravity and keep the scooter from tipping Pride recommends that the scooter user determine his her personal limitations and practice bending and reaching in the presence of a qualified attendant A Maxima WARNING Do not bend lean or reach for objects if you have to pick them up from the scooter deck or from either side of the scooter Movements such as these may change your centre of gravity and the weight dist
8. an incline it is best to lean forward See figures 2 and 2A This shifts the centre of gravity of you and your scooter toward the front of the scooter for improved stability NOTE When negotiating ramps if the throttle control lever is released while moving forward the powered scooter may rollback approximately 30 5 cm 1 foot before the brake engages If the throt tle control lever is released while moving in reverse the powered scooter may rollback approximately 1 metre 3 feet before the brake engages Figure 2 Normal Driving Position Figure 2A Increased Stability Driving Position CORNERING INFORMATION Excessively high cornering speeds can create the possibility of tipping Factors which affect the possibility of tipping include but are not limited to cornering speed steering angle how sharply you are turning uneven road surfaces inclined road surfaces riding from an area of low traction to an area of high traction such as passing from a grassy area to a paved area especially at high speed while turning and abrupt directional changes High cornering speeds are not recommended If you feel that you may tip over in a corner reduce your speed and steering angle 1 e lessen the sharpness of the turn to prevent your scooter from tipping WARNING When cornering sharply reduce your speed maintain a stable centre of gravity When using your scooter at higher speeds do not corner sharply This greatly reduc
9. ensure the smooth operation of your scooter WARNING It is critically important that the psi bar kPa air pressure rating indicated on the tyre be maintained in pneumatic tyres at all times Do not underinflate or overinflate your tyres Low pressure result in loss of control and overinflated tyres may burst J Failure to maintain the psi bar kPa air pressure rating indicated pneumatic tyres at all times may result in tyre and or wheel failure C WARNING Inflate your scooter tyres from a regulated air source with an available pressure gauge Inflating your tyres from an unregulated air source could overinflate them resulting in a burst tyre NOTE If the tyres on your scooter list the psi rating only use the following conversion formulas to find the bar or kPa rating bar psi x 0 06895 kPa psi x 6 89476 INCLINE INFORMATION More and more buildings have ramps with specified degrees of inclination designed for easy and safe access Some ramps may have turning switchbacks 180 degree turns that require you to have good cor nering skills on your scooter Proceed with extreme caution as you approach the downgrade of a ramp or other incline Take wide swings with your scooter s front wheel s around any tight corners If you do that the scooter s rear wheels will follow a wide arc not cut the corner short and not bump into or get hung up on any railing corners When driving down a ramp
10. fork seat post and frame welds Drivetrain including differential motor and brake ONE YEAR LIMITED WARRANTY Your Pride Scooter is fully guaranteed for twelve 12 months from the date of purchase against faults arising due to defects in manufacture or materials This warranty does not detract from but is in addition to your legal rights All electronic parts including controllers and battery chargers have a one 1 year warranty Servicing to the controller or battery charger must be carried out by your authorised Pride Provider Any attempt to open or dismantle these items renders the guarantee void on that item NOT COVERED UNDER WARRANTY This guarantee does not extend to those items which may need replacement due to normal wear and tear tyres belts bulbs upholstery plastic shrouds motor brushes fuses and batteries or damage to the prod uct caused by misuse or accident for which Pride or its agent cannot be held responsible This warranty does not include labour or service calls BATTERIES Batteries are covered by a six 6 month warranty from the original manufacturer Gradual deterioration in performance due to being left in a discharged state left in cold conditions for long periods of time or worn out through heavy use is not covered SERVICE CHECKS AND WARRANTY SERVICE Warranty service can be performed by an authorised Pride Provider Please contact your authorised Pride Provider for advice on the current cost
11. motor vehicle The scooter should be stowed in the boot of a car or in the back of a truck or van with batteries removed and properly secured In addition all removable scooter parts including the armrests seat and shroud should be removed and or properly secured during motor vehicle transport WARNING Although your scooter may be equipped with a positioning belt this belt is not designed to provide proper restraint during motor vehicle transport Anyone traveling in a motor vehicle should be properly secured in the motor vehicle seat with safety belts fastened securely WARNING Do not sit on your scooter while it is in a moving vehicle WARNING Always be sure your scooter and its batteries are properly secured when it is being transported Batteries should be secured in an upright position and protective caps should be installed on the battery terminals Batteries should not be transported with any flammable or combustible items POSITIONING BELTS Your authorised Pride Provider therapist s and other healthcare professionals are responsible for deter mining your requirement for a positioning belt in order to operate your scooter safely in WARNING If you require positioning belt to safely operate your scooter make sure it is fastened securely in order to reduce the possibility of a fall from the scooter GETTING ONTO AND OFF OF YOUR SCOOTER Getting onto and off of your scooter requires a good sense of balance
12. operated If the power seat switch is pressed while the scooter is in motion the scooter will slow and come to a stop The scooter may also produce a fault code If a fault code occurs you will need to turn the scooter s power off then back on again before proceeding Instances may occur when the power seat is raised to reach something or get a better vantage point and not returned to its lowest position before operating the scooter again Depending on how high the power seat is raised your scooter s speed will be reduced when operating the scooter Elevating the power seat to approximately one half its maximum height limits your scooter s speed to half that set with the speed adjustment dial If the power seat is elevated to approximately three quarters its maximum height the scooter will not move if the throttle control lever is pressed The power seat must be lowered to slightly under three quarters of its maximum height in order to drive the scooter agian The scooter cannot be driven at full speed until the scooter s seat is lowered to approximately one half its maximum height It is strongly recommended that the scooter not be operated with the power seat elevated 28 www pridemobility com Maxima VI COMFORT ADJUSTMENTS POSITIONING BELT Your scooter seat may be equipped with an auto type positioning belt that can be adjusted for operator comfort The positioning belt is designed to help sup port the operator so that he
13. pridemobility com 17 YOUR SCOOTER Anti tip Wheels The front not shown and rear anti tip wheels are an integral and important safety feature of your scooter They are bolted to the frame at the front and rear of the scooter PROHIBITED Do not remove the anti tip wheels or modify your scooter in any way that is not authorised by Pride Motor Transaxle Assembly Not Shown The motor transaxle assembly is the electromechanical unit that converts the electrical energy of your scooter s batteries into the controlled mechanical energy that drives the scooter s wheels Batteries Not Shown The batteries store the electrical energy that powers your scooter See IV Batteries and Charging Main Circuit Breaker Reset Button When the voltage in your scooter s batteries becomes low or your scooter is heavily strained because of excessive loads or steep inclines the main circuit breaker may trip to protect your scooter s motor and electronics from damage The main circuit breaker reset button pops out when the breaker trips When the breaker trips the entire electrical system of your scooter shuts down Allow a minute or two for your scooter s electronics to rest Push in the reset button to reset the breaker If the breaker trips frequently you may need to charge your batteries more often You may also need to have your authorised Pride Provider perform a load test on your scooter s batteries If the main
14. snow salt mist spray conditions and on icy slippery your scooter in a dry and clean condition upholstered and non upholstered items on the scooter possibly resulting in skin irritation Exercise caution when using your scooter in extremely hot or cold conditions NI WARNING Prolonged exposure to hot or cold conditions may affect the temperature of or when exposing your scooter to direct sunlight for prolonged periods of time FREEWHEEL MODE Your scooter is equipped with a manual freewheel lever that when engaged allows the scooter to be pushed For more information about how to place your scooter into and out of freewheel mode see III Your Scooter WARNING When your scooter is in freewheel mode the braking system is disengaged Disengage the drive motors only a level surface Ensure the key is removed from the key switch Stand behind scooter to engage disengage freewheel mode Never sit scooter to do this m After you have finished pushing your scooter always return it to the drive mode to lock the brakes An added feature built into the scooter is push too fast protection which safeguards scooter against gaining excessive speed while in freewheel mode Push too fast operates differently depending on which of two conditions exists If the key is switched off when in freewheel mode scooter s controller activates regenerative braking when
15. the scooter is pushed faster than a maximum threshold which has been preprogrammed In this case the controller is acting as a speed governor Ifthe key is switched on while in freewheel mode you will encounter considerable resistance at any speed This prevents the scooter from gaining unwanted momentum should the manual freewheel lever inadvertently be released while driving the scooter STAIRS AND ESCALATORS Scooters are not designed to travel up or down stairs or escalators Always use a lift WARNING Do not use your scooter to negotiate steps or escalators DOORS Determine if the door opens toward or away from you Use your hand to turn the knob or push the handle or push bar Drive your scooter gently and slowly forward to push the door open Or drive your scooter gently and slowly rearwards to pull the door open Maxima www pridemobility com 11 11 SAFETY LIFTS Modern lifts have a door edge safety mechanism that when pushed reopens the lift door s If you are in the doorway of a lift when the door s begin to close push on the rubber door edge or allow the rubber door edge to contact the scooter and the door will reopen Use care that handbags packages or scooter accessories do not become caught in lift doors NOTE If your scooter s turning radius is greater than 152 4 cm 60 in it may be difficult to maneuver in lifts and building entrances Use caution when attempting to tur
16. E WHEEL REPLACEMENT If your scooter is equipped with pneumatic tyres and you have a flat tyre you can have the tube replaced If your scooter is equipped with a solid tyre insert either the solid insert or the entire wheel must be replaced depending on the model Contact your authorised Pride Provider for information regarding replacement wheels for your scooter AXLE KEY WARNING Wheels on your scooter should only be serviced replaced by an 5 authorised Pride Provider or qualified DRIVE WHEEL WASHER technician DRIVE WHEEL NUT WARNING Be sure that the key is removed from key switch and the scooter is not freewheel mode before performing this procedure Figure 27 Drive Wheel Removal WARNING When changing a tyre remove only the centre lug nut then remove the wheel If any further disas sembly is required deflate the tyre completely or it may explode Follow these easy steps for a quick and safe repair of solid tyres 1 Remove the key from the key switch 2 Elevate the side of the scooter of which you are removing the tyre Place wooden blocks under the frame to elevate the scooter 3 Remove the drive wheel nut and washer from the axle See figure 27 4 Pull the wheel off the axle 5 Slide the new wheel back onto the axle Make sure that the axle key is in the axle slot See figure 27 mounting the wheel can result in electronic brake failure personal injury and or product damage
17. E This owner s manual is compiled from the latest specifications and product information avail able at the time of publication We reserve the right to make changes as they become necessary Any changes to our products may cause slight variations between the illustrations and explanations in this manual and the product you have purchased The latest current version of this manual is available on our website This product is manufactured by Pride Mobility Products Corporation 182 Susquehanna Avenue Exeter PA 18643 2694 USA Copyright 2010 Pride Mobility Products Australia Pty Ltd vV ACN 088 609 661 INFMANU2689 Rev C November 2010 I INTRODUCTION 4 SAFETY 5 YOUR SCOOTER 15 BATTERIES AND CHARGING 19 24 VI COMFORT ADJUSTMENTS 26 VII DISASSEMBLY AND ASSEMBLY 30 BASIC TROUBLESHOOTING 33 IX CARE AND MAINTENANCE 35 WARRANTY ana ae i aS 39 APPENDIX I SPECIFICATIONS 40 Maxima www prid
18. ace the batteries while the scooter is occupied WARNING The batteries on your scooter should only be serviced or replaced by an authorised Pride Provider or a qualified technician PROHIBITED Keep tools and other metal objects away from the battery terminals Con tact with tools can cause electrical shock You may need the following to change your batteries metric standard socket set and ratchet adjustable spanner To change the batteries in your scooter Remove the seat and the rear shroud See VII Disassembly and Assembly Disconnect the battery tie down straps Disconnect the battery harnesses from the rear electronics module Disconnect the battery cables from the battery terminals Remove the old batteries Place a new battery in each battery well Connect the red battery cables to the positive battery terminals Connect the black battery cables to the negative battery terminals Reconnect the battery harnesses to the rear electronics module 10 Reconnect the battery tie down straps 11 Reinstall the rear shroud and the seat CHONDA RWNS NOTE If you encounter a damaged or cracked battery immediately enclose it in a plastic bag and contact your local waste disposal agency or your authorised Pride Provider for instructions on disposal and battery recycling which is our recommended course of action Why do my new batteries seem weak Deep cycle batteries employ a different chemical technology than i
19. affecting the service visit REPLACEMENT UNITS The availability of replacement units and or spare parts is subject to the discretion of the provider not the manufacturer For more information regarding replacement units and or spare parts contact your autho rised Pride Provider Maxima www pridemobility com 39 APPENDIX I SPECIFICATIONS MAXIMA SPECIFICATIONS Model Numbers 3 wheel SC900AU 4 wheel SC940AU Overall Length 3 wheel 117 6 cm 46 3 in 4 wheel 119 4 cm 47 in Overall Width2 64 8 cm 25 5 in Total Weight Without Batteries 3 wheel 77 5 kg 171 108 4 wheel 80 kg 176 Ibs Heaviest Piece When Disassembled Rear Frame 32 kg 70 Ibs Turning Radius2 3 wheel 132 1 cm 52 in 4 wheel 137 2 cm 54 in Speed maximum Variable up to 9 km h 5 6 mph Range Per Charge With NF 22 batteries 3 wheel Up to 29 11 km 18 09 miles 4 wheel Up to 25 75 km 16 miles With U 1 batteries Up to 15 45 km 9 6 miles Ground Clearance 8 1 cm 3 2 in Weight Capacity 227 kg 500 Ibs Standard Seating Type DX contour medium black Dimensions 56 cm 22 in width x 46 cm 18 in depth x 47 cm 18 5 in height Material Grey Beige or Black Vinyl or Grey Fabric Standard Seat Weight 19 kg 41 Ibs Drive System Rear wheel drive sealed transaxle with a 24 volt DC motor Dual Braking System Regenerative and electromechanical Tyres Type Solid PU Foam F
20. an traffic rules Wait until your path is clear of traffic and then proceed with extreme caution STATIONARY OBSTACLES STEPS KERBS ETC WARNING Do not drive near raised surfaces unprotected ledges and or drop offs kerbs porches stairs etc WARNING Do not attempt to have your scooter climb or descend an obstacle that is inordinately high WARNING Do not attempt to have your scooter proceed rearward down any step kerb or other obstacle This cause scooter to tip WARNING Be sure your scooter is traveling perpendicular to any kerb you may be required to ascend or descend See figures 3 and 4 WARNING Even though your scooter may be capable of handling greater obstacles Pride recommends that you do not attempt to negotiate a kerb that has a height greater than 5 cm 2 in Doing so could cause instability in your scooter Figure 3 Correct Kerb Approach Figure 4 Incorrect Kerb Approach 10 www pridemobility com Maxima 11 SAFETY INCLEMENT WEATHER PRECAUTIONS Exposure of your scooter to inclement weather conditions should be avoided whenever possible If sud denly caught up in rain snow severe cold or heat while operating your scooter proceed to shelter at the earliest opportunity Thoroughly dry your scooter before storing charging or operating your scooter surfaces can cause damage to the scooter and electrical system Maintain and store PROHIBITED Operating in rain
21. and less electrical current to the batteries When the batteries are fully charged the current sent to them from the charger is at nearly zero amperage Therefore when the charger is plugged in it maintains the charge on your scooter s batteries but does not overcharge them We do not recommend that you charge your scooter s batteries for more than 24 consecutive hours 20 www pridemobility com Maxima IV BATTERIES AND CHARGING What if my scooter s batteries won t charge Ensure the red and black battery cables are connected properly to the battery terminals Ensure both battery harnesses that extend from the batteries are plugged into their mating harness leading to the charger Ensure both ends of the charger power lead are inserted fully Can I use a different charger Chargers are selected precisely for particular applications and are especially matched to the type size and chemical formulation of specific batteries For the safest and most efficient charging of your scooter s batteries we recommend use of the charger supplied as original equipment with your Pride product only Any charging method resulting in batteries being charged individually is especially prohibited How often must I charge the batteries Two major factors must be considered when deciding how often to charge your scooter s batteries All day scooter use on a daily basis Infrequent or sporadic scooter use With these c
22. anti tip wheels the motor transaxle assembly not shown the electronics module the batteries not shown the main circuit breaker reset button and the fuses are located on the rear section of your scooter See figure 6 Refer to VII Disassembly and Assembly for instructions on removing the rear shroud RIGHT RUNNING STORAGE COMPARTMENT LIGHT FUSE RIGHT TURN ELECTRONICS MODULE itl a INDICATOR REMOVE REAR SHROUD TO FUSE VIEW ENTIRE MODULE RIGHT TURN INDICATOR LIGHT BULB LIGHT COVER MANUAL FREEWHEEL LEVER MAIN CIRCUIT BREAKER RESET BUTTON ANTI TIP WHEEL Figure 6 Rear Section Manual Freewheel Lever Whenever you need or want to push your scooter for short distances you can put it in freewheel mode 1 Pull up firmly on the manual freewheel lever to disable the drive system and the brake system 2 You may push your scooter 3 Push down firmly on the manual freewheel lever to reengage the drive system and the brake system and take your scooter out of freewheel mode WARNING When your scooter is in freewheel mode the braking system is disengaged Disengage the drive motors only a level surface Ensure the key is removed from the key switch E Stand to the side of scooter to engage disengage freewheel mode Never sit a scooter to do this mE After you have finished pushing your scooter always return it to the drive mode to lock the brakes Maxima www
23. cially trained in assisting a scooter user in various daily living activities As you begin using your scooter during daily activities you will probably encounter situations in which you will need some practice Simply take your time and you will soon be in full and confident control as you maneuver through doorways on and off lifts up and down ramps and over moderate terrain Below are some precautions tips and other safety considerations that will help you become accustomed to operating the scooter safely MODIFICATIONS Pride has designed and engineered your scooter to provide maximum mobility and utility A wide range of accessories is available from Pride to further customise your scooter to better suit your needs and or preferences However under no circumstances should you modify add remove or disable any feature part or function of your scooter N WARNING Do not modify your scooter in any way not authorised by Pride Do not use 2 accessories if they have not been tested approved for Pride products REMOVABLE PARTS WARNING not attempt to lift move your scooter by of its removable parts including the armrests seat or shroud PRE RIDE SAFETY CHECK Get to know the feel of your scooter and its capabilities Pride recommends that you perform a safety check before each use to make sure your scooter operates smoothly and safely 6 www pridemobility com Maxima 11 SAFETY Perform th
24. circuit breaker trips repeatedly see your authorised Pride Provider for service Fuses The fuses help protect your scooter s lighting control console assembly and charging systems from receiving an overload of electrical current The fuses used in the scooter are the same type automobiles use If a fuse must be replaced use only the specified amp fuse See Care and Maintenance Docking Device Assembly Your scooter is equipped with a docking device assem bly See figure 7 In order to utilise the docking device it is necessary to purchase an insert T bar or Bullnose and C arm that when used with the lift system will aid in lifting your scooter DOCKING DEVICE Contact your authorised Pride Provider for more informa tion about the docking device 19 Figure 7 Docking Device Assembly 18 www pridemobility com Maxima IV BATTERIES AND CHARGING BATTERIES AND CHARGING Your scooter requires two long lasting 12 volt deep cycle batteries that are sealed and maintenance free They are recharged by an off board charging system Charge your scooter s batteries prior to using it for the first time Keep the batteries fully charged to keep your scooter running smoothly READING YOUR BATTERY VOLTAGE The battery condition meter on the control console assembly indicates the approximate strength of your batteries using a colour code From right to left green indicates fully charged batteries yello
25. do not exceed the psi bar kPa air pressure rating indicated on pneumatic tyres Plan your route ahead to avoid as many hills cracked broken or soft surfaces as possible Limit your baggage weight to essential items Try to maintain an even speed while your scooter is in motion Avoid stop and go driving What type and size of battery should I use We recommend deep cycle batteries that are sealed and maintenance free Both AGM and Gel Cell are deep cycle batteries that are similar in performance Do not use wet cell batteries which have removable caps J WARNING Corrosive chemicals are contained in batteries Use only AGM or Gel Cell N batteries to reduce the risk of leakage or explosive conditions 4 NOTE Sealed batteries are not serviceable Do not remove the caps Maxima www pridemobility com 21 IV BATTERIES AND CHARGING How do I change a battery in my scooter MANDATORY Battery posts terminals and related accessories contain lead and lead compounds Wear goggles and gloves when handling batteries and wash hands after handling WARNING Always use two batteries of the exact same type chemistry and amp hour Ah capacity Refer to the specifications table in this manual and in the manual supplied with the battery charger for recommended type and capacities WARNING Contact your authorised Pride Provider if have any questions regarding the batteries in your scooter WARNING Do not repl
26. e 5 lever may be in the freewheel position wheel lever to the drive position restart your scooter HERE Throttle trip The throttle control lever Release the throttle control lever completely 6 may have been depressed while inserting then reinsert the key the key HERE Throttle trip The throttle control lever Contact your authorised Pride Provider for 7 may have been depressed while inserting assistance the key HERE The scooter s motor is disconnected Contact your authorised Pride Provider for 8 assistance HERE Possible controller trip You may be Shut down your scooter for a minimum of sev 9 attempting to install the battery while the eral minutes to allow the controller to cool Or key is inserted or the motor controller may try reinserting the key into the key switch be in overheat protective mode What if all the systems on my scooter seem to be dead Make certain that the key is in the position Check that the batteries are fully charged See IV Batteries and Charging Push in the main circuit breaker reset button See HI Your Scooter Make certain that both battery harnesses are firmly connected to the electronics module and to the battery terminals See VII Disassembly and Assembly Disassembly and Assembly Make sure that the front to rear harness is firmly connected to the electronics module See VII Check the fuses See IX Care and Maintenanc
27. e for fuse replacement Be sure the power down timer feature has not been activated See V Operation Maxima www pridemobility com 33 VIII BASIC TROUBLESHOOTING What if the motor runs but my scooter does not move With the key turned to the on position check the status LED If the LED flashes three times pauses briefly then flashes two times this is the manual freewheel lever code meaning your scooter is in freewheel mode When the manual freewheel lever is pulled up the brakes are disengaged and all power to the transaxle is cut Push down the manual freewheel lever to restore normal operation to your scooter See HI Your Scooter What if the main circuit breaker repeatedly trips Charge the scooter s batteries more frequently See IV Batteries and Charging Ifthe problem continues have both of your scooter s batteries load tested by your authorised Pride Provider You may also perform the load test yourself Battery load testers are available at most automotive parts stores Follow the directions supplied with the load tester See IV Batteries and Charging for information about your scooter s battery type What if the battery condition meter dips way down and the motor surges or hesitates when I press my scooter s throttle control lever Fully charge your scooter s batteries See IV Batteries and Charging Have your authorised P
28. e following inspections prior to using your scooter Check for proper tyre inflation Maintain but do not exceed the psi bar kPa air pressure rating indicated on each tyre if equipped with pneumatic tyres Check all electrical connections Make sure they are tight and not corroded Check all harness connections to the electronics module Make sure they are secured properly Check the brakes See Care and Maintenance Check battery charge See IV Batteries and Charging NOTE If you discover a problem contact your authorised Pride Provider for assistance WEIGHT LIMITATIONS Your scooter is rated for a maximum weight capacity Please refer to the specifications table for this limit Keep in mind that the maximum weight capacity includes the combined weight of the user and any accessories mounted to the scooter NI MANDATORY Stay within the specified weight capacity of your scooter Exceeding the weight capacity voids your warranty Pride will not held responsible for injuries and Ne A or property damage resulting from failure to observe weight limitations WARNING Do not carry passengers on your scooter Carrying passengers on your scooter may affect the centre of gravity resulting in a tip or a fall TYRE INFLATION If your scooter is equipped with pneumatic tyres you should check or have the air pressure checked at least once a week Proper inflation pressures will prolong the life of your tyres and help
29. e most control over your vehicle Set the speed adjustment dial to your desired speed Press your thumb against the appropriate side of the throttle control lever The electromechanical disc park brake automatically disengages and the scooter accelerates smoothly to the speed you preselected with the speed adjustment dial Pull on the left handgrip to steer your scooter to the left Pull on the right handgrip to steer your scooter to the right Move the tiller to the centre position to drive straight ahead To stop slowly release the throttle control lever The electronic brakes will automatically engage when your scooter comes to a stop NOTE Your scooter s reverse speed is slower then that of the forward speed you preset with the speed adjustment dial 24 www pridemobility com Maxima OPERATION GETTING OFF YOUR SCOOTER Bring your scooter to a complete stop Remove the key from the key switch Push down on the seat rotation lever and rotate the seat until you are facing toward the side of your scooter Make certain that the seat is fixed securely in position Carefully and safely get out of the seat and stand to the side of your scooter You can leave the seat facing to the side to facilitate boarding your scooter next time Nee Ne POWER DOWN TIMER FEATURE Your scooter is equipped with an energy saving automatic power down timer feature designed to preserve your scooter s battery life If you mistakenl
30. eat floorboard N or tyre tread as they will become dangerously slippery CLEANING AND DISINFECTION Use a damp cloth and mild non abrasive cleanser to clean the plastic and metal parts of your scooter Avoid using products that may scratch the surface of your scooter If necessary clean your product with an approved disinfectant Make sure the disinfectant is safe for use on your product before application cleaning agent before applying it to your product Failure to comply may result in skin A WARNING Follow all safety instructions for the proper use of the disinfectant and or A irritation or premature deterioration of upholstery and or scooter finishes BATTERY TERMINAL CONNECTIONS Make certain that the terminal connections remain tight and uncorroded The batteries must sit flat in the battery wells The battery terminals should face the rear of the scooter AXLE BEARINGS AND THE MOTOR TRANSAXLE ASSEMBLY These items are all prelubricated sealed and require no subsequent lubrication MOTOR BRUSHES The motor brushes are housed inside of the motor transaxle assembly They should be inspected periodi cally for wear by your authorised Pride Provider CONSOLE CHARGER AND REAR ELECTRONICS Keep these areas away from moisture Before operating your scooter allow any of these areas to dry thoroughly if they have been exposed to moisture Maxima www pridemobility com 35 IX CARE AND MAINTENANC
31. ect the motor harness when disassembling the scooter See figure 21 7 Lift both batteries off the scooter See figure 22 8 Push the locking cam levers forward to the unlocked position and remove the ball detent pins See figures 23 and 24 9 Remove the frame handle ball detent pin See figure 25 10 Gently slide the two sections of the scooter apart See figure 26 11 Grab the hand grip on the tiller pull upward on the tiller adjustment lever and fully lower the tiller down to the centre of the scooter chassis 1 rA Figure 25 Frame Handle Ball Detent Pin Figure 26 Frame Separation Maxima www pridemobility com 31 VII DISASSEMBLY AND ASSEMBLY ASSEMBLY NOTE Raise the tiller before starting to reassemble the scooter 1 why ON Place the manual freewheel lever in the drive down position Position the front and rear sections next to each other Tilt the rear end to a horizontal position and insert the longer tube of the front end into the rear section first make sure that the locking cam levers are in the unlocked forward position and the ball detent pins are removed Slide the two sections of the unit together until the front half reaches its insertion limit Secure the front and rear sections with the ball detent pins Push the locking cam levers back to their locked upward position Replace the frame handle ball detent pins Plug t
32. emobility com 3 INTRODUCTION WELCOME to Pride Mobility Products Pride scooter you have purchased combines state of the art components with safety comfort and styling in mind We are confident that these design features will provide you with the conveniences you expect during your daily activities Once you understand how to safely operate and care for your scooter it should give you years of trouble free operation and service Read and follow all instructions warnings and notes in this manual and all other accompanying literature before attempting to operate this product for the first time In addition your safety depends upon you as well as your provider carer or healthcare professional in using good judgement If there is any information in this manual which you do not understand or if you require additional assis tance for setup or operation please contact your authorised Pride Provider Failure to follow the instruc tions in this manual and those located on your scooter can lead to personal injury and or damage to the scooter including voiding the warranty PURCHASER S AGREEMENT By accepting delivery of this product you promise that you will not change alter or modify this product or remove or render inoperable or unsafe any guards shields or other safety features of this product fail refuse or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the
33. en the seat and the tiller See figure 11 1 Remove the seat from your scooter See VII Disassembly and Assembly 2 Remove the four bolts that fasten the seat to the seat platform 3 Align the seat platform with the desired set of holes on the seat 4 Install the four bolts securely ARMREST WIDTH ADJUSTMENT The armrests can be adjusted inward or outward See figure 12 1 Loosen the armrest adjustment knobs at the back of the seat frame 2 Slide the armrests in or out to the desired width 3 Tighten the armrest adjustment knobs The armrests also pivot upward to make getting onto and off of your scooter easier ARMREST HEIGHT ADJUSTMENT The height of both armrests can be adjusted upward or downward See figure 12 1 Loosen the two setscrews located on the armrest receiver 2 Raise or lower the armrest to the desired height 3 Tighten the setscrews to secure the armrest TILLER ADJUSTMENT LEVER Figure 10 Tiller Adjustment Lever SEAT ROTATION LEVER SEAT BOLTS ARMREST HEIGHT ADJUSTING SETSCREWS ARMREST ADJUSTMENT KNOB Figure 12 Armrest Adjustments 26 www pridemobility com Maxima VI COMFORT ADJUSTMENTS SEATBACK ADJUSTMENT The seatback may be positioned to four differ ent angles 90 100 102 and 105 See fig ure 13 UPPER HINGE To adjust the seatback angle 1 Loosen and remove the adjustment screw from the seatback hinge on both sides of the seat 2 Rep
34. es the possibility of a tip or fall BRAKING INFORMATION Your scooter is equipped with two powerful brake systems Regenerative Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the centre stop position Disc Park Brake Activates mechanically after regenerative braking slows the vehicle to near stop or when power is removed from the system for any reason Maxima www pridemobility com 9 11 SAFETY OUTDOOR DRIVING SURFACES Your scooter is designed to provide optimum stability under normal driving conditions dry level sur faces composed of concrete blacktop or tarmac However Pride recognises that there will be times when you will encounter other surface types For this reason your scooter is designed to perform admirably on packed soil grass and gravel Feel free to use your scooter safely on lawns and in park areas Avoid driving on uneven terrain and or soft surfaces Avoid tall grass that can become tangled in the running gear Avoid loosely packed gravel and sand Do not use your scooter in fresh or salt water Do not use your scooter at the edge of a stream lake or ocean If you feel unsure about a driving surface avoid that surface PUBLIC STREETS AND ROADWAYS WARNING You should not operate your scooter on public streets and roadways 2 aware that it be difficult for traffic to see you when seated your scooter 2 Obey local pedestri
35. g objects Drive your scooter only with the power seat in the lowest position Driving the scooter with the power seat elevated could cause instability in the scooter resulting in a tip or a fall x Strict adherence to the following safety rules is vital to your safety Operate the power seat only while completely stationary on level ground E Do not press the throttle control lever and the power seat switch at the same time E not operate your scooter with the power seat elevated Operate the scooter only with the power seat fully retracted in the lowest position m Never place your scooter in freewheel mode with the power seat elevated Use extreme caution when reaching for objects with your power seat elevated Do not overextend or attempt to pick up objects that might affect your balance Do not attempt to raise or lower the seat while in motion Before operating the power seat ensure your scooter is level and stationary and the speed adjustment dial is set to the slowest setting To operate the power seat 1 Press and hold the upper part of the power seat switch to raise the seat Release the switch when you have attained your desired height or upon reaching the highest position 2 Press and hold the lower part of the power seat switch to lower the seat Release the switch when you have attained your desired height or upon reaching the lowest position NOTE The scooter must be stopped in order for the power seat to be
36. h your scooter is capable of climbing slopes greater than those illustrated in figure 1 do not under any circumstances exceed the incline guidelines or any other specifications presented in this manual Doing so could cause instability in your scooter Handicap public access ramps are not subject to government regulation in all countries and therefore do not necessarily share the same standard percent of slope Other inclines may be natural or if man made not designed specifically for scooters Figure 1 illustrates your scooter s stability and its ability to climb grades under various weight loads and under controlled testing conditions These tests were conducted with the scooter s seat in the highest position and adjusted rearward on the seat base to its farthest rearward position Use this information as a guideline Your scooter s ability to travel up inclines is affected by your weight your scooter s speed your angle of approach to the incline and your scooter setup WARNING Any attempt to climb or descend a slope steeper than what is shown in figure 1 may put your scooter an unstable position and cause it to tip 4 WARNING Never carry an oxygen tank weighing more than 6 8 kg 15 Ibs Never fill the rear basket with contents exceeding 6 8 kg 15 1 5 227 kg 500 Ibs 10 5 6 Figure 1 Maximum Recommended Incline Angle 8 www pridemobility com Maxima 11 SAFETY When you approach
37. harger and may damage the batteries NOTE The LED lights on the charger indicate different charger conditions at various times charger power on charging in progress and charging complete Refer to the manual supplied with the charger for a complete explanation of these indicators PLUGS INTO THE OFF BOARD CHARGER PORT OFF VOLTAGE SWITCH PLUGS INTO ELECTRICAL OUTLET Figure 9 Charger On Off and Voltage Switches Figure 9A Off board Charger Follow these easy steps to charge your batteries safely 1 Position your scooter close to a standard electrical outlet 2 Remove the key from the key switch 3 Make certain that the manual freewheel lever is in the drive forward position 4 Plug the charger power lead into the off board charger port on your scooter We recommend that you charge the batteries for 8 to 14 hours 5 When the batteries are fully charged unplug the charger power lead from the electrical outlet and then from the charger power lead receptacle NOTE There is a charger inhibit function on your scooter The scooter will not run and the battery condition meter will not operate while the batteries are charging FREQUENTLY ASKED QUESTIONS How does the charger work When your scooter s battery voltage is low the charger works harder and sends more electrical current to the batteries to bring up their charge As the voltage of the batteries approaches a full charge the charger sends less
38. he front to rear harness into its mating plug Put the batteries in place and plug both black and white 2 pin battery harnesses into their mating plugs Reconnect the battery tie down strap 11 12 13 Reinstall the rear shroud Reinstall the seat Rotate the seat until it is securely in place 32 www pridemobility com Maxima VIII BASIC TROUBLESHOOTING Any electromechanical device occasionally requires some troubleshooting However most of the problems that may arise can usually be solved with a bit of thought and common sense Many of these problems occur because the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge DIAGNOSTIC FLASH CODES The diagnostic flash codes for your scooter are designed to help you perform basic troubleshooting quickly and easily A diagnostic flash code flashes from the status LED in the event one of the conditions listed below develops NOTE Your scooter will not run unless the flash code condition is resolved and the scooter has been turned off then turned back on FLASH CODE CONDITION SOLUTION f Battery voltage is too low to operate the Charge fully until charger and any meters 2 scooter indicate completion Battery voltage is too high to operate the Contact your authorised Pride Provider for 3 scooter assistance Solenoid brake trip manual freewheel Remove the key then push the manual fre
39. hroud the basket and the batteries See figure 16 No tools are required to disassemble or assemble your scooter but keep in mind that the disassembled sections of the scooter take up more floor space than the assembled unit Always disassemble or assemble your scooter on a level dry surface with sufficient room for you to work and move around your scooter about 2 metres 5 feet in all directions Remember that some scooter components are heavy and you may need assistance when lifting them BASKET BATTERIES Figure 16 The Scooter Disassembled R 2 WARNING Do not lift beyond your physical capability Ask for assistance when necessary while disassembling or assembling your scooter To disassemble the scooter Place the manual freewheel lever in the drive down position Lift the seat straight up and off the scooter See figure 17 Gently lift the rear shroud off of the scooter See figure 18 Disconnect the battery tie down strap that holds the batteries in place Unplug both black and white 2 pin battery harnesses See figure 19 Unplug the front to rear harness from its mating plug See figure 20 NOE eS WARNING Failure to unplug both battery harnesses and the front to rear harness prior to N frame separation could result in permanent damage to the scooter nesses Harness 30 www pridemobility com Maxima VII DISASSEMBLY AND ASSEMBLY NOTE There is no need to disconn
40. keep the scooter s speed adjustment set to the slowest speed setting to ensure a safely controlled descent Avoid sudden stops and starts Maxima www pridemobility com 7 11 SAFETY When climbing an incline try to keep your scooter moving If you must stop start up again slowly and then accelerate cautiously When driving down an incline do so by setting the speed adjustment dial to the slowest setting and driving in the forward direction only If your scooter starts to move down the incline faster than you anticipated or desired allow it to come to a complete stop by releasing the throttle control lever Then push the throttle control lever forward slightly to ensure a safely controlled descent WARNING When on any sort of an incline or decline never place the scooter in freewheel mode especially while seated on it or standing next to it WARNING When climbing an incline do not zigzag or drive at an angle up the face of the incline Drive your scooter straight up the incline This greatly reduces the possibility of a tip or a fall Always exercise extreme caution when negotiating an incline N WARNING Do not drive your scooter across the side of an incline or diagonally up or down incline do not stop if possible while driving up or down incline x 24 WARNING You should not travel up down a potentially hazardous incline i e areas covered with snow ice cut grass or wet leaves WARNING Even thoug
41. le can increase the susceptibility of the vehicle to EMI Do not modify your scooter in any way not authorised by Pride WARNING The electrically powered mobility vehicle itself can disturb the performance of other electrical devices located nearby such as alarm systems NOTE For further information on EMI RFI visit the Resource Center on www pridemobility com If unintended motion or brake release occurs turn your scooter off as soon as it is safe to do so Contact your authorised Pride Provider to report the incident 14 www pridemobility com Maxima YOUR SCOOTER CONTROL CONSOLE ASSEMBLY The control console assembly houses all of the controls you need to drive your scooter including the key switch speed adjustment dial status LED throttle control lever battery condition meter horn buttons lights switch turn indicator buttons off board charger port and the hazard lights switch See figure 5 the control console assembly does become exposed to moisture do not attempt to PROHIBITED Do not expose the control console assembly to moisture In the event that operate your scooter until the control console assembly has dried thoroughly BATTERY CONDITION METER STATUS LED SPEED ADJUSTMENT DIAL KEY KEY SWITCH RIGHT TURN INDICATOR BUTTON 7a HAZARD 2 LIGHTS LIGHTS SWITCH HORN BUTTON HORN BUTTON THROTTLE CONTROL LEVER REVERSE THROTTLE CONTROL LEVER FORWARD OFF BOARD CHARGER PORT Figure 5 Cont
42. m Replacement light bulbs can be purchased from your authorised Pride Provider NOTE Use only 24 volt light bulbs 1 Remove the light cover 2 Gently remove the bulb by pulling it straight out 3 Insert a new bulb of the same wattage 4 Replace the light cover FUSE REPLACEMENT In the event a fuse should cease to work 1 Remove the fuse by pulling it out of its slot 2 Examine the fuse to be sure it is blown See figures 28 and 29 3 Insert a new fuse of the proper rating 2 WARNING The replacement fuse must exactly match the rating of the fuse being 2 N replaced Failure to use properly rated fuses may cause damage to the electrical system Figure 28 Working Fuse Figure 29 Blown Fuse Replace Maxima www pridemobility com 37 IX CARE AND MAINTENANCE NYLON LOCK NUT REPLACEMENT Any nylon insert lock nut removed during the periodic maintenance assembly or disassembly of the scooter must be replaced with a new nut Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert resulting in a less secure fit Replacement nylon insert lock nuts are available at local hardware stores or through your authorised Pride Provider STORING YOUR SCOOTER If you plan on not using your scooter for an extended period of time it is best to Fully charge its batteries prior to storage
43. n or maneuver your scooter in small spaces and avoid areas that might pose a problem LIFT ELEVATION PRODUCTS If you will be transporting your scooter during travel you may find it necessary to use a vehicle mounted lift system or elevation product to aid in transportation Pride recommends that you closely review the warnings instructions specifications and safety information set forth by the manufacturer of the lift elevation product before using that product WARNING Not all lift systems elevation products are rated for use with an occupied mobility device Pride recommends that you do not remain seated in your scooter when it is being used in connection with any type of lift system elevation product unless N That product is rated for occupied use by the manufacturer are able to occupy your mobility device in strict conformity with the warnings instructions specifications and safety guidelines set forth by the manufacturer WARNING Always turn off the power to the unit when you are being transferred via an elevation product Failure to do so may result in accidental throttle control lever contact resulting in unintended movement and personal injury or product damage BATTERIES In addition to following the warnings below be sure to comply with all other battery handling information MANDATORY Battery posts terminals and related accessories contain lead and lead G compounds Wear goggles and gl
44. onsiderations in mind you can determine just how often and for how long you should charge your scooter s batteries We designed the battery charger so that it will not overcharge your scooter s batteries do not charge them for more than 24 consecutive hours However you may encounter some problems if you do not charge your batteries often enough and if you do not charge them on a regular basis Following the five guidelines below will provide safe and reliable battery operation and charging Ifyou use your scooter daily charge its batteries as soon as you finish using it for the day Your scooter will be ready each morning We recommend that you charge your scooter s batteries for 8 to 14 hours after daily use Ifyou use your scooter once a week or less charge its batteries at least once a week for 12 to 14 hours at a time Keep your scooter s batteries fully charged Avoid deeply discharging your scooter s batteries How can I get maximum range or distance per charge Rarely will you have ideal driving conditions smooth flat hard driving surfaces with no wind or curves You will often face hills pavement cracks uneven and loosely packed surfaces curves and wind All of these driving conditions affect the distance or running time per battery charge Below are a few suggestions for obtaining the maximum range per battery charge Always fully charge your scooter s batteries prior to your daily use Maintain but
45. or she does not slide down or forward in the seat The positioning belt is not designed for use as a restraining device To install the positioning belt if required 1 Remove the seat from your scooter 2 Place the seat upside down so that you can see the bottom of the seat base See figure 11 3 Use spanner to remove the two back bolts on the outermost part of the rear seat 4 Insert the bolt through the appropriate ends of the positioning belt and then reinstall the bolts and belt back into the seat bottom 5 Tighten the bolts To adjust the positioning belt for operator comfort 1 Insert the metal tab on the right side of the belt into the plastic housing on the opposite strap until you hear a click See figure 15 2 Pull the strap on the right side of the belt until it is secure but not so tight as to cause discomfort MANDATORY Make sure the posi tioning belt is properly secured to the scooter and is adjusted for oper ator comfort before each use MANDATORY Inspect the position 7 ing belt for loose or damaged parts before each use of the scooter If you discover a problem contact your authorised Pride Provider for mainte nance and repair Figure 15 Positioning Belt Maxima www pridemobility com 29 VII DISASSEMBLY AND ASSEMBLY DISASSEMBLY You can disassemble the scooter into several pieces REAR SECTION FRONT SECTION the seat the front section the rear section the rear s
46. osition the seatback to the desired angle 3 Align the adjustment holes from the upper ADJUSTMENT SCREW and lower hinge so the adjustment screw can easily pass through 4 Reinsert both adjustment screws and tighten LOWER HINGE SEAT HEIGHT ADJUSTMENT The seat can be repositioned to different heights See figure 14 1 Remove the seat and rear shroud from your scooter See VII Disassembly and Assembly 2 Loosen the nut and remove it from the bolt and remove the bolt and washers from the lower seat post 3 Raise or lower the upper seat post to the desired seat height UPPER SEAT POST 4 While holding the upper seat post at that height match up the holes in the upper seat NUT post with those of the lower seat post 5 Reinstall the bolt washers and nut to WASHER secure the seat post NOTE Ensure both washers have been rein stalled before fully tightening the nut 6 Reinstall the rear shroud and the seat LOWER SEAT POST Figure 14 Seat Height Adjustment Maxima www pridemobility com 27 VI COMFORT ADJUSTMENTS POWER SEAT ADJUSTMENT Your scooter may be equipped with a power seat The power seat actuator is designed to raise or lower the seat with minimal effort on the part of the operator The power seat switch is located on the control console WARNING The power seat is intended for operation only while your scooter is stationary and on a level surface Its purpose is to aid you in reachin
47. our home or familiar surroundings until you have become accustomed to your scooter s controls and have properly broken in your scooter s batteries 3 Fully recharge the batteries They should be at over 90 of their peak performance level 4 Operate your scooter again How can I ensure maximum battery life Fully charged deep cycle batteries provide reliable performance and extended battery life Keep your scooter s batteries fully charged whenever possible Batteries that are regularly and deeply discharged infrequently charged or stored without a full charge may be permanently damaged causing unreliable performance and limited service life What about public transport If you intend to use public transport with your scooter you must contact the transportation provider in advance to determine their specific requirements Maxima www pridemobility com 23 OPERATION BEFORE GETTING ON YOUR SCOOTER Have you fully charged the batteries See IV Batteries and Charging Is the manual freewheel lever in the drive down position Never leave the manual freewheel lever pulled up unless you are manually pushing your scooter GETTING ONTO YOUR SCOOTER 1 Make certain that the key is removed from the key switch from the key switch This will prevent the scooter from moving if accidental throttle i WARNING Never attempt to get onto or off your scooter without first removing the key control lever contact is made
48. oves when handling batteries and wash hands after 57 handling WARNING Scooter batteries are heavy See specifications table If you are unable to lift that much weight be sure to get help Use proper lifting techniques and avoid lifting beyond your capacity WARNING Always protect the batteries from freezing and never charge frozen battery Charging a frozen battery may result damage to the battery WARNING Connect the battery harnesses in the proper manner RED cables must be connected to positive battery terminals posts BLACK cables must be connected to negative battery terminals posts Protective caps should be installed over all battery terminals REPLACE cables immediately if damaged BATTERY DISPOSAL AND RECYCLING If you encounter a damaged or cracked battery immediately enclose it in a plastic bag and contact your local waste disposal agency or your authorised Pride Provider for instructions on disposal and battery recycling which is our recommended course of action PREVENTING UNINTENDED MOVEMENT of time turn off the power This will prevent unexpected motion from inadvertent throttle control lever contact f N WARNING If you anticipate being seated in a stationary position for an extended period 4 12 www pridemobility com Maxima 11 SAFETY MOTOR VEHICLE TRANSPORT Pride recommends that you do not remain seated in your scooter while traveling in a
49. r WO 6 201 8 46 ____ gt 46 cm 18 56 in heel 117 6 cm 46 3 in heel 119 4 cm 47 in 61 71 cm 24 28 in y Turning Radius 137 4 cm 54 1 in 9 64 8 25 5 Figure 30 Scooter Dimensions Maxima www pridemobility com 4 42 www pridemobility com Maxima Mobility Products Australia Pty Ltd 21 Healey Road Dandenong 3175 Victoria Australia ACN 088 609 661 www pridemobility com NFMANU2689
50. ribution of the scooter and cause your scooter to tip PROHIBITED Keep your hands away from the tyres when driving Be aware that loose fitting clothing can become caught in drive tyres www pridemobility com 11 SAFETY PRESCRIPTION DRUGS PHYSICAL LIMITATIONS The scooter user must exercise care and common sense when operating his her scooter This includes awareness of safety issues when taking prescribed or over the counter drugs or when the user has specific physical limitations medication or if you have certain physical limitations Some medications and limitations J WARNING Consult your physician if are taking prescribed over the counter may impair your ability to operate your scooter safe manner 8 ALCOHOL SMOKING The scooter user must exercise care and common sense when operating his her scooter This includes awareness of safety issues while under the influence of alcohol or while smoking WARNING Do not operate your scooter while you are under the influence of alcohol as this may impair your ability to operate the scooter in a safe manner WARNING Pride strongly recommends that you do not smoke cigarettes while seated on your scooter although the scooter seat has passed the necessary testing requirements for cigarette smoking You must adhere to the following safety guidelines if you decide to smoke cigarettes while seated on your scooter Do not leave lit cigarettes unat
51. ride Provider load test each battery Or see the previous troubleshooting question for load testing the batteries yourself If you experience any problems with your scooter that you are not able to solve immediately contact your authorised Pride Provider for information maintenance and service 34 www pridemobility com Maxima IX CARE AND MAINTENANCE Your scooter requires a minimal amount of care and maintenance If you do not feel confident in your ability to perform the maintenance listed below you may schedule inspection and maintenance at your authorised Pride Provider The following areas require periodic inspection and or care and maintenance TYRE PRESSURE If equipped with pneumatic tyres always maintain the psi bar kPa air pressure rating indicated on each tyre WARNING It is critically important that the psi bar kPa air pressure rating be maintained in pneumatic tyres at all times Do not underinflate or overinflate your tyres Low A pressure result loss of control and overinflated tyres may burst Failure to maintain the psi bar kPa air pressure rating indicated on pneumatic tyres at all times may result in tyre and or wheel failure S 2A Regularly inspect your scooter s tyres for signs of wear EXTERIOR SURFACES Bumpers tyres and trim can benefit from an occasional application of rubber or vinyl conditioner WARNING Do not use a rubber or vinyl conditioner on the scooter s vinyl s
52. rol Console Assembly Key Switch Fully insert the key into the key switch and turn it clockwise to power up turn on your scooter Turn the key anticlockwise to power down turn off your scooter WARNING If the key is moved to the off position while your scooter is motion the electronic brakes engage and your scooter comes to an abrupt stop lt Speed Adjustment Dial This adjustment dial enables you to preselect and limit your scooter s top speed The image of the tortoise represents the slowest speed setting The image of the hare represents the fastest speed setting Status LED The Status LED alerts you to electrical problems that may occur with the scooter The LED remains constantly lit while your scooter is on If the scooter develops an electrical problem the status LED will flash a code See Basic Troubleshooting for troubleshooting flash codes Maxima www pridemobility com 15 YOUR SCOOTER Throttle Control Lever This lever allows you to control the forward speed and the reverse speed of your scooter up to the maxi mum speed you preset with the speed adjustment dial Place your right hand the right handgrip and your left hand on the left handgrip Use your right thumb to push the right side of the lever to disengage your scooter s brakes and move forward Release the lever and allow your scooter to come to a complete stop before pushing the other side of
53. ront 7 5 cm x 25 cm 3 in x 10 in Rear 10 cm x 25 4 in x 10 in Battery Requirements Type Two 12 volt deep cycle Size U 1 31 36 Ah NF 22 55 Ah Battery Weight Approximately U 1 11 kg 24 5 Ibs each 22 17 kg 38 Ibs each Battery Charger Off board charger Varies with base model user weight terrain type battery amp hour rating Ah battery charge battery condition motors controller type tyre type and tyre condition This specification can be subject to a variance of 10 5 Due to manufacturing tolerances and continued product improvement this specification can be subject to variance of or 3 3 AGM or Gel Cell type required See VI Batteries and Charging 4 Tested in accordance with ANSI RESNA WC Vol 2 Section 4 amp ISO 7176 4 standards Results derived from theoretical calculation based on battery specifications and drive system performance Test conducted at maxi mum weight capacity 5 Battery weight may vary based on battery manufacturer 6 conducted SC900 at maximum weight capacity NOTE This product conforms to all applicable ANSI RESNA testing requirements and ISO 7176 ENI12184 standards All specifications subject to change without notice 40 www pridemobility com Maxima APPENDIX I SPECIFICATIONS 4 wheel 61 7 62 5 cm 24 3 24 6 in 2 m g o
54. s used in car batteries nickel cadmium batteries nicads or in other common battery types Deep cycle batteries are specifically designed to provide power drain down their charge and then accept a relatively quick recharge We work closely with our battery manufacturer to provide batteries that best suit your scooter s specific electrical demands Fresh batteries arrive daily at Pride and are shipped fully charged to our customers During shipping the batteries may encounter temperature extremes that may influence their initial perfor mance Heat diminishes the charge on the battery cold slows the available power and extends the time needed to recharge the battery 22 www pridemobility com Maxima IV BATTERIES AND CHARGING It may take a few days for the temperature of your scooter s batteries to stabilise and adjust to their new room or ambient temperature More importantly it takes a few charging cycles a partial drain followed by a full recharge to establish the critical chemical balance that is essential to a deep cycle battery s peak performance and long life Follow these steps to properly break in your scooter s new batteries for maximum efficiency and ser vice life 1 Fully recharge any new battery prior to its initial use This charging cycle brings the battery up to about 88 of its peak performance level 2 Operate your new scooter in familiar and safe areas Drive slowly at first and do not travel too far from y
55. safe use of this product SHIPPING AND DELIVERY Before using your scooter make sure your delivery is complete as some components may be individually packaged If you do not receive a complete delivery please contact your authorised Pride Provider imme diately Where damage has occurred during transport either to the packaging or content please contact the delivery company responsible INFORMATION EXCHANGE We want to hear your questions comments and suggestions about this manual We would also like to hear about the safety and reliability of your new scooter and about the service you received from your authorised Pride Provider Please notify us of any change of address so we can keep you apprised of important informa tion about safety new products and new options that can increase your ability to use and enjoy your scooter Please feel free to contact us at the address below Pride Mobility Products Australia Pty Ltd 21 Healey Road Dandenong 3175 Victoria Australia NOTE If you ever lose or misplace your product registration card or your copy of this manual contact us and we will be glad to send you a new one immediately 4 www pridemobility com Maxima 11 SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the scooter to identify warnings mandatory actions and prohibited actions It is very important for you to read and understand them completely Read and follow the information in the owner s manual
56. t the battery charger wiring and connectors for damage before each use Contact your authorised Pride Provider if damage is found WARNING Do not attempt to open battery charger case If the battery charger does not appear to be working correctly contact your authorised Pride Provider WARNING If the off board battery charger is equipped with cooling slots then do not attempt to insert objects through these slots WARNING If your battery charger has not been tested and approved for outdoor use then do not expose it to adverse or extreme weather conditions If the battery charger is exposed to adverse or extreme weather conditions then it must be allowed to adjust to the difference in environmental conditions before use indoors Refer to the manual supplied with the battery charger for more information Maxima www pridemobility com 19 IV BATTERIES AND CHARGING The off board charger supplied with your scooter is equipped with a 115 230 voltage switch Confirm that this switch is in the proper position for your locality If you are not sure what the voltage is in your country contact your local electricity provider before inserting the charger power lead plug into your electrical outlet If the setting is incorrect the charger will not function properly Slide the voltage switch to the appropriate position See figure 9 WARNING Failure to ensure the voltage switch is in the proper position can cause dam age to the c
57. tended Keep ashtrays a safe distance from the seat cushions Always make sure cigarettes are completely extinguished before disposal ELECTROMAGNETIC AND RADIO FREQUENCY INTERFERENCE EMI RFI WARNING Laboratory tests have shown that electromagnetic and radio frequency waves can have an adverse affect on the performance of electrically powered mobility M vehicles Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones mobile two way radios such as walkie talkies radio stations TV stations amateur radio HAM transmitters wireless computer links microwave signals paging transmitters and medium range mobile transceivers used by emergency vehicles In some cases these waves can cause unintended movement or damage to the control system Every electrically powered mobility vehicle has an immunity or resistance to EMI The higher the immunity level the greater the protection against EMI This product has been tested and has passed at an immunity level of 20 V M WARNING Be aware that cell phones two way radios laptops and other types of radio transmitters may cause unintended movement of your electrically powered mobility vehicle due to EMI Exercise caution when using any of these items while operating your mobility vehicle and avoid coming into close proximity of radio and TV stations WARNING The addition of accessories or components to the electrically powered mobility vehic
58. w indicates a draining charge and red indicates that an immediate recharge is necessary See figure 8 To ensure the highest accuracy the battery condition meter should be checked while operating your scooter at full speed on a dry level surface CHARGING YOUR BATTERIES Figure 8 Battery Condition A PROHIBITED Never use an extension lead to plug in your battery charger Plug charger directly into a properly Meter gt wired standard electrical outlet PROHIBITED Removal of grounding prong can create electrical hazard If necessary properly install an approved 3 pronged adapter to an electrical outlet having 2 pronged N plug access PROHIBITED Do not allow unsupervised children to play near the scooter while the batteries are charging Pride recommends that you do not charge the batteries while the scooter is occupied MANDATORY Read the battery charging instructions in this manual and in the manual supplied with the battery charger before charging the batteries WARNING Explosive gases may be generated while charging the batteries Keep the scooter and battery charger away from sources of ignition such as flames or sparks and provide adequate ventilation when charging the batteries WARNING Ensure that both ends of the charger power lead are clean and dry before plugging the charger power lead into the off board charger port or the electrical outlet WARNING Inspec
59. y leave the key in the key switch and in the on position but do not use your scooter for approximately 20 minutes the scooter s controller shuts down automatically Although the controller is shut down and the scooter will not move power will still be supplied to the scooter s lighting system If the power down timer feature takes effect perform the following steps to resume normal operation 1 Turn the key to the off position 2 Turn the key back to the on position Maxima www pridemobility com 25 VI COMFORT ADJUSTMENTS TILLER ANGLE ADJUSTMENT WARNING Remove the key from the key switch before adjusting the tiller or the seat Never attempt to adjust the tiller or the seat while the scooter is in motion Your scooter is equipped with a pivoting tiller that allows adjust ment to several positions 1 Lift the tiller adjustment lever See figure 10 2 Move the tiller to a comfortable position 3 Release the tiller adjustment lever to secure the tiller in position SEAT ROTATION ADJUSTMENT The seat rotation lever secures the seat in one of four positions See figure 11 1 Push the seat rotation lever down to disengage the seat 2 Rotate the seat to the desired position 3 Release the seat rotation lever to fix the seat securely in place FRONT TO BACK SEAT ADJUSTMENT You can reposition the scooter s seat forward or rearward to one of three settings to adjust the distance betwe

MAXIMA - Pride Mobility Products

Contents

Download Pdf Manuals

Related Search

Related Contents