CL600 Front and Back Plates
Contents
1. 26 09 2013 Codelocks CL600 Front And Back Plates Installation CL600 Front and Back Plates CL600 Front and Back Plates Number relating to picture Item CL600 Front Plate and handle Back Plate and handle Neoprene seals x 2 RED and BLUE tipped spindles Fixing bolts x 3 1 x spare Front plate cylinder cover Allen Keys x 2 1 pair euro profile cylinder escutcheons Keyhole escutcheons Code change keys Adaptor kit for mortise locks with horizontal fixings Code change tool CON DU BRWN F WO O 6 x X X X X X X Xl XK Tools Required e Power Drill e Drill bit 10mm e Philips screwdriver Check operation of the coded front plate The code may be entered in any sequence i e 1370 may be entered as 0731 or any other sequence of those numbers There are a total of 8 191 codes available any of which may be entered in any order The CL600 model is intended to replace the conventional door furniture fitted to an existing mortise latch or an existing mortise lock which has both a spring latch and a deadbolt The square follower should be 8mm square Any lock and key mechanism is retained to operate the deadbolt The CL600 will only operate the latchbolt and not the deadbolt A mortise lock case should have holes for fixing bolts to pass through on either side of the square latch follower and sometimes additionally a hole below the follower See figure 1 and confirm that your lockcase is compatible with th2. e CL600 lock plates www codelocks co uk products Vew cl600_ front_and_back_plates installation 1 3 26 09 2013 Codelocks CL600 Front And Back Plates Installation mm latch follower Through fixing holes either side of the follower iat Through fixing hole below the follower FIGURE 1 lockcase IMPORTANT When using CL600 front and back plates only please test with your selected locks case to ensure that the latch retracts fully from the code side without too much resistance Some lock cases have a heavily sprung latch follower designed for use with un sprung lever furniture This heavy springing can defeat the clutch on our locks Please note the code chamber for mechanical locks requires the lever to be rotated at least 45 degrees to re set the lock for the next code user Please contact Codelocks technical department if you are unsure Codelocks Limited does not accept responsibility for products incorrectly specified If your lockcase has a hole below the follower fig 1 A proceed as follows 1 Hold the black neoprene seal against the door vertically with the rectangular hole centrally over the follower Mark the top and bottom holes on the door face and repeat the procedure on the other side of the door Remove the lock Drill the three 10mm holes through the door Drill from both sides for greater accuracy and to avoid splintering out of the door face Check that the existing spindle hole is at least 18mm dia
3. meter Fit the lock 2 Take the BLUE or RED tipped spindle and fit to the code side according to the hand of your door see diagram Ne a Door hung on LEFT viewed from the code side Fit remaining spindle to inside non code side 3 Cut three of the socket head bolts to the required length for your door Approximate overall length should be door thickness plus 25mm to allow about 10mm of threaded bolt to enter the outside plate 4 Remove plastic insert plug from frontplate Apply the front and back plates with the neoprene seals in position against the door over the protruding ends of the spindle 5 Fix the two plates together using the socket head bolts starting with the top fixing Ensure that the two plates are truly vertical and then tighten the bolts using the T shaped Allen key Do not use excessive force www codelocks co uk products Vew cl600_ front_and_back_plates installation 26 09 2013 Codelocks CL600 Front And Back Plates Installation 6 Fit the lever handles to suit the hand of the door To change the hand of a lever handle loosen the grub screw with the small Allen key reverse the lever handle and fully tighten the grub screw 7 Ensure that the latchbolt retracts after the code is entered and the lever handle is depressed Now check the operation of the inside lever handle If there is any binding of the handles or latch the loosen the bolts slightly and reposition the plates until the correct positio
4. n is found and then re tighten the bolts If your lockcase only has holes on either side of the follower fig 1 B proceed as follows 1 Hold the black neoprene seal against the door perfectly vertically with the rectangular hole centrally over the follower Mark the top hole and the holes on either side of the follower if not already drilled using adaptor plate as guide then repeat the procedure on the other side of the door Mark an extra hole on the inside of the door in line with the bottom fixing hole Remove the lock Drill the 4 x 10mm holes from both sides for greater accuracy and to avoid splintering out of the door face Check that the existing spindle hole is at least 18mm Drill the extra 12mm hole 5mm deep on the inside of the door to accept the fixing nut on the adaptor plate Replace the lock 2 Take the BLUE or RED tipped spindle and fit to the code side according to the hand of your door see diagram Door hung on RIGHT viewed from the code side aed Door hung on LEFT viewed from the code side Fit remaining spindle to inside non code side 3 Take the adaptor kit item 9 on the contents table Cut the two M5 countersunk head bolts to length to suit the door thickness i e door thickness plus a maximum of 10mm no more than 5mm should enter the front plate Hold the front plate with the three hole neoprene seal against the door over the protruding spindle Fromthe other side of the door fix the adaptor
5. plate to the front plate using the two M5 countersunk bolts Before tightening up the fixings make sure that the spindle hole is centrally positioned over the follower Do not use excessive force 4 Cut two of the long socket head bolts to the required length for your door Approximate overall length should be door thickness plus 25mm to allow about 10mm of threaded bolt to enter the front plate Place the neoprene gasket over the adaptor plate Use the screw with the T shaped Allen key to fix the back plate to the front plate through the TOP holes Using the 20mm socket head bolt fix the back plate through the BOTTOM hole to the adaptor plate Do not use excessive force 5 Check that the lever handles are correctly fitted for the hand of door To change the hand of a lever handle loosen the grub screw with the small Allen key reverse the lever handle and full tighten the grub screw 6 Before closing the door enter the code and check that the latchbolt retracts when the lever handle is depressed Now check the operation of the inside lever handle If there is any binding of the handles or latch then loosen the top and bottom bolts and reposition the plates slightly until the correct position is found and then re tighten the bolts www codelocks co uk products vew cl600_ front_and_back_plates installation 3 3
Download Pdf Manuals
Related Search