Go-Go Travel Lift - Pride Mobility Products
Contents
1. NOTE This owner s manual is compiled from the latest specifications and product information avail able at the time of publication We reserve the right to make changes as they become necessary Any changes to our products may cause slight variations between the illustrations and explanations in this manual and the product you have purchased The latest current version of this manual is available on our website ACN 088 609 661 Copyright 2007 Pride Mobility Products Corp INFMANU2803 Rev C July 2007 CONTENTS INTRODUCTION NN d non eee 4 o e mm 5 E MN IUe mE 8 V OPERATION e PP 14 Me TROUBLESHOOTING E E E cies 16 VI I 10 2 RB 17 Go Go Travel Lift www pridemobilitycom 3 I INTRODUCTION SAFETY WELCOME to Pride Mobility Products Corporation Pride The product you have purchased combines state of the art components with safety comfort and styling in mind We are confident that these design features will provide you with the conveniences you expect during your daily activities Understanding how to safely operate and care for this product should bring you years of trouble free operations and service Read and follow all instructions warnings and notes in this manual and all other accompanying literature before attempting to operate this product for the first time In addition your safety depends2. 60 kg Subjecting the Go Go Travel Lift to the strain of lifting more than it is designed to may cause it to fail damaging your scooter injuring the person operating the lift or both 6 Ifthe scooter begins to tilt lower it completely and adjust the docking device by moving the pick up bar in the direction of the tilt when using a C arm 7 Tighten the pick up bar once the proper balance point has been found when using a C arm 8 Once the scooter is raised high enough to fit into the vehicle stop the lift See figure 16 9 Swing the boom arm toward the vehicle When the scooter is securely in the vehicle lower the lift strap until all of the scooter s wheels are on a solid surface Figure 17 Securing The Boom Arm 10 If installed in a van disconnect the hook from the docking device and attach it to the T bar on the base extension This prevents the boom arm from swinging freely while the automobile is in motion Operate the lift in the upward direction until the strap is snug See figure 17 WARNING When transporting the lift secure the boom arm to prevent it from rotating in any direction A swinging boom arm can be a hazard If you can t secure the boom arm to prevent it from swinging freely remove the motor housing andlay it flat inside the vehicle WARNING Do not overtighten the strap Doing so may put unwanted strain on the motor causing the circuit breaker to trip NOTE If
3. Be sure that the strap is not pinched when inserting the pin Figure 8 Boom Arm Adjustment 4 Reinstall the bow tie cotter pin L BASE INSTALLATION After determining the ideal spot for your lift to be permanently mounted remove the entire lift from the vehicle except for the L base 1 Inspect the undercarriage of the vehicle where the lift L base is located for obstructions that may hinder the installation of the five 5 mounting bolts that will secure the L base to the vehicle Obstructions may consist of electrical wiring gas tank bumper mounts or exhaust pipes You may need to adjust the base extensions to clear obstructions If possible install the L base with the base extensions fully extended See figure 9 WARNING The bumper mounts on some vehicles are gas pressured DO NOT drill into them They may explode casing severe injury 10 Www pridemobility com Go Go Travel Lift lll INSTALLATION 2 Ifallis clear under the L base mark the position of the five 5 mounting holes and drill them using a 3 8 in drill bit Drill all mounting holes from inside the vehicle See figure 9 Reinstall the L base and align the mounting holes of the L base with the holes you just drilled 4 Position T bar on the end of the base support that runs parallel with the rear of the vehicle and install a mounting bolt and washer through it and the L base See figure 9 pa NOTE The T bar need only be installed in van or SUV
4. The lift strap should drop straight down to the T bar See figure 14 WARNING Inspect the lifting strap N before each use for twisting K fraying and signs of wear Figure 13 Hand Control DOCKING DEVICE T BAR m Keep tension on the lifting strap with your free hand when lowering the lifting hook m Lower the lifting hook only to T bar of the docking device f WARNING Do not extend the A lifting strap past the warning label 4 located it See figure 15 4 Placethelifting hook onto the docking device T bar See figure 14 5 Operate the lift in the upward direction WARNING Pinch Crush Hazard Always keep hands clear of the lifting strap while the SilverBoom is lifting lowering a mobility device The operator of the lift should stand a safe distance away i from the mobility device being lifted lowered to ensure that feet are never positioned undera raised mobility device Figure 15 Lifting Strap Warning Label 14 www pridemobility com Go Go Travel Lift IV OPERATION Do not drag the scooter into position using the lift If dragging occurs your scooter is too far away from the vehicle To prevent dragging m Release the lifting strap tension then remove the hook from the docking device m Correct the position of the scooter Attempt the lift again MANDATORY The maximum weight the Go Go Travel Lift was designed to lift is 130 Ibs
5. her feet are never positioned under araised scooter TRANSPORT VEHICLE POSITIONING Be sure your vehicle is parked on flat level ground before attempting to lift a scooter WARNING Attempting to lift a scooter when a vehicle is not on level ground will cause the N scooter to swing toward or away from the vehicle making it difficult to get the scooter into the vehicle Go Go Travel Lift www pridemobilitycom 7 lll INSTALLATION The Go Go Travel Lift can be installed in either side of your vehicle The illustrations demonstrate installa ton on theright side PROHIBITED Avoid exposure to rain snow ice salt or standing water whenever possible Maintain wy and store in a clean and dry condition NOTE Most roads have a crown to help with water runoff However if the crown is severe enough it may cause difficulty getting your scooter into the vehicle In this case it may be better to install the lift on the left side DETERMINE L BASE LOCATION 1 Assemble the L Base See figure 1 For opti mal use insert the base extensions into the L base at their farthest extension point and install the hardware nuts and bolts The base exten sions can be adjusted to accommodate obstruc tions NOTE Always insert the bolt from the inside of the L base This allows the base extensions to be properly tightened without rattling 2 Before permanently installing the lift place the L base inside your vehi
6. installed in a trunk disconnect the black red power harness see figure 12 and remove the motor housing and upper post and place it in an area where it will be secure The height of the boom arm will not allow the trunk to close 11 Disconnectthe power to the Go Go Travel Lift to prevent any accidental movement when transporting your scooter WARNING Your Go Go Travel Lift was designed to be mounted primarily vehicle fw Mounting your Go Go Travel Lift on a platform where the height of the lift may cause the N lifting strap to extend beyond a safe point can damage the Go Go Travel Lift and injure the operator of the lift Go Go Travel Lift Www pridemobility com 15 V TROUBLESHOOTING LIFT WILL NOT OPERATE m Check the circuit breaker reset button Reset if necessary See figure 18 Ensure all harness connections are secure Ensure the power wire leading to the positive battery terminalis tight and not corroded m Check the fuse located on the red power wire near the battery If blown replace with a new 25 amp fuse See figure 19 CIRCUIT BREAKER RESET x WARNING Do not use a higher BUTTON JN rated fuse than 25 amp Doing so may damage the lift s electrical system LIFT STOPS OPERATING If your Go Go Travel Lift is heavily strained because of excessive loads the main circuit breaker see fig ure 18 may trip to protect the motor and electronics from damage When the breaker trip
7. GO DGO Go Go Travel Lift 3 E d gt 1 800 800 8586 US 1 888 570 1113 CANADA SAFETY GUIDELINES An authorised Pride Provider or qualified technician must perform the initial setup of this product and must perform all of the procedures in this manual The symbols below are used throughout this owner s manual and on the Go Go Travel Lift to identify warn ings and important information It is very important for you to read them and understand them completely WARNING Indicates a potentially hazardous condition situation Failure to follow designated procedures can cause either personal injury component damage or malfunction On the product this icon is represented as a black symbol on a yellow triangle witha black border MANDATORY These actions should be performed as specified Failure to perform mandatory actions can cause personal injury and or equipment damage On the product this icon is represented as a white symbol on a blue dot with a white border PROHIBITED These actions are prohibited These actions should not be performed at any time or in any circumstances Performing a prohibited action can cause personal injury and or equipment damage On the product this icon is represented as a black symbol with a red circle and red slash Please fill out the following information for quick reference Pride Provider Address Phone Number Purchase Date Serial Number
8. a clean and dry condition Only authorized personnel may service this equipment Disposal and recycling Contact your authorized Pride Providerfor information on proper disposal of your Pride product and its packaging Disposal and recycling Contact your authorized Pride Provider forinformation on proper disposal of your Pride product and its packaging www pridemobility com Go Go Travel Lift SAFETY LIFTING CAPABILITIES The maximum weight the Go Go Travel Lift was designed to lift is 130 Ibs 60 kg Under no circumstances should the Go Go Travel Lift be made to lift more than 130 Ibs Subjecting the Go Go Travel Lift to the strain of hoisting more than it is designed to lift may cause it to fail damaging your scooter injuring the person operating the lift or both weight of your scooter Verify with your authorized Pride Provider that the total weight of AN WARNING Adding accessories oversize batteries or a different seat will increase the A your scooter after the additions does not exceed 130 Ibs 60 INSTALLATION Your Go Go Travel Lift system was designed to be mounted primarily in a vehicle Mounting your Go Go Travel Lift on a platform where the height of the lift may cause the lifting strap to extend beyond a safe point can damage the Go Go Travel Lift and injure the operator of the lift The distance between the top of the boom arm and the scooter should not exceed 70 in 177 8 cm when the boom arm is fu
9. cle in the area in which you intend to install it See figure 2 for L base posi tioning in vehicles with hatchbacks or figure 3 for trunk installation Positioning the L base close to the rear allows the boom arm to stay as short as possible this enables the boom arm to swing freely without making contact with the vehicle VEHICLES WITH TRUNKS Position the L base as shown in figure 3 You may need to situate the L base so the wheel well doesn t interfere with the L base extensions Ensure there is adequate room for a scooter to comfortably fit into the trunk 8 www pridemobility com Figure 2 L Base Hatchback Installation WHEEL WELL Figure 3 L Base Trunk Installation Go Go Travel Lift lll INSTALLATION ASSEMBLING THE LIFT 1 Insert the upper post into the L base See figure 4 2 Assemble the split ring collar See figure 5 3 Slide the split ring collar over the upper post and tighten both screws a good starting point is approximately 12in 30 cm down from the top of the upper post See figure 4 To en sure safe operation the split ring collar must be secured no closer than 5 in 12 5 cm from the top of the upper post WARNING Failing to tighten both screws of the split ring collar could cause damage to your lift scooter and vehicle N C NOTE The split ring collar may need to be ad justed down so the boom arm has sufficie
10. der Please notify us of any change of address so we can keep you apprised of important information about safety new products and new options that can increase your ability to use and enjoy your scooter Please feel free to contact us at the address below USA Canada Pride Mobility Products Corporation Pride Mobility Products Company Attn Customer Care Department 380 Vansickle Road Unit 350 182 Susquehanna Ave St Catharines Ontario L2R 6P7 Exeter PA 18643 2694 1 888 570 1113 Customercare pridemobility com 1 800 424 8250 NOTE If you ever lose or misplace your product registration card or your copy of this manual contact us and we will be glad to send you a new one immediately 4 Www pridemobility com Go Go Travel Lift ll SAFETY PRODUCT SAFETY SYMBOLS The symbols below are used on the scooter to identify warnings mandatory actions and prohibited ac tions It is very important for you to read and understand them completely this point Read and follow the information in the owner s manual Do not lift scooter while seated in it Do not lift people Maximum lifting capacity Pinch Crush points created during assembly and or operation Do not lift pets Do not extend the lifting strap past the warning label Go Go Travel Lift www pridemobilitycom 5 II SAFETY es E 69 62 Avoid exposure to rain snow ice salt or standing water whenever possible Maintain and store in
11. installations When the lift is installed inside a trunk it is necessary to remove the motor housing and upper post for the trunk to close 5 Install the four 4 remaining mounting bolts and washers onto L base NOTE Choosing the correct length bolt allows enough bolt thread to pass through the undercarriage ensuring enough room for the mounting washer and nut to be installed securely 6 From under the vehicle install the mounting washers and nuts to all five 5 mounting bolts and tighten See figure 9 NOTE The two holes in the mounting washers are for working around obstructions Choose the hole that best works in the area you are installing the mounting bolts MOUNTING BOLTS 50 MM 2 OR 75 3 WASHER 85 d M MOUNTING HOLE Figure 9 Securing The L Base Go Go Travel Lift www pridemobilitycom 11 lll INSTALLATION 7 Placethe L base cap over the L base and secure it with the supplied screws See figure 10 8 Reinstall the upper post 9 Reinstall the motor housing and make adjustments as necessary The liftis now fully assembled See figure 11 10 MM PHILLIPS HEAD SCREW 1 L BASE CAP Figure 10 L Base Cap Figure 11 Fully Assembled Lift ELECTRICAL WIRING INSTALLATION 1 Route the lift s long red positive power wire starting at the lift through the interior of the vehicle until you reach the automobile battery See figure 12 Concea
12. l the wire behind or under the interior panels there should be existing holes Be certain that the wire is protected with a rubber grommet when passing it through the metal panels and into the engine compartment Inside the engine compartment secure the wire to the firewall and the inner fender with the supplied plastic wire ties Use care not to cause abrasions to the power wire Itis important to secure the power wire at various points along its run WARNING The red positive wire must be connected directly to the positive battery terminal M 2 Connectthe short portion with fuse of the red positive power wire to the positive battery terminal 3 Insert the end of the long portion of the red power wire into the yellow connector of the short portion and crimp it securely Once crimped pull on the wire gently to ensure a good connection Wrapping the connector with electrical tape will help prevent moisture from corroding the connection 12 www pridemobility com Go Go Travel Lift lll INSTALLATION 4 Connectthe short black ground wire to clean bare metal area of the vehicle using 12 mm 1 2 in sheet metal screw provided Mount to an area close to the base of the lift This allows adeguate slack in the wire to make the harness connections m Drilla 1 16 in pilot hole where the ground wire will be attached to the vehicle M Insert the screw through the ring at the end of the black ground wire and ins
13. lly extended Read and fully understand the directions for drilling the mounting holes for the Go Go Travel Lift base 7 WARNING Before drilling the mounting holes your vehicle absolutely certain A through a visual inspection there are no obstructions in the path of the drill bit such as the fuel tank exhaust pipes or electrical wires LIFTING NON GO GO TRAVEL LIFT ITEMS The Go Go Travel Lift is an extremely versatile device which users may employ to lift items other than Pride products Pride has no control over such use nor can Pride anticipate every possible use to which a Go Go Travel Lift may be put Lifting non Pride products with the Go Go Travel Lift is done at the operator s own risk and Pride accepts no liability for damage or injury resulting from such use PRELIFT INSPECTION Inspect the lifting strap of the Go Go Travel Lift before every use for twisting fraying and signs of wear If signs of wear become evident have the strap replaced by your authorized Pride Provider WARNING A frayed or worn lifting strap can snap resulting in damage to the scooter being lifted and injury to the lift operator To find weight of the scooter you are lifting refer to its owner s manual OPERATOR POSITIONING Keep hands clear of the lifting strap while the Go Go Travel Lift is lifting lowering a scooter The operator of the lift should standa safe distance from the unit being lifted lowered to ensure that his
14. nt head room to swing into a vehicle or adjusted up so the scooter being lifted has ample room to clear obstructions 4 Lowerthe motor housing over the upper postuntil it rests on the split ring collar See figure 6 WARNING Pinch Crush hazard Keep hands clear of the upper post lt when lowering the motor housing N A VEHICLES WITH HATCHBACKS MINI VANS STATION WAGONS ETC Once the lift is assembled and seated on the L base close the hatch slowly to make sure the lift doesn t make contact with it If the liftis too close to the rear adjust its position slightly until the hatch can close with out making contact with the lift Positioning the L base close to the rear allows the boom arm to stay as short as possible This enables the lift to swing into the vehicle without contacting the far side of the ve hicle WARNING The lift will be top heavy until mounted securely Get assistance to help stabilize the lift while swinging the boom arm You may need to adjust the height of the motor hous ing see figures 6 and 7 or the length of the boom arm see figure 8 so the boom arm can swing freely without hitting at any point inside the vehicle Go Go Travel Lift MINIMUM OF 5 12 5 CM SPLIT RING COLLAR UPPER POST Figure 4 Upper Post Installation 1 BRING RING HALVES TOGETHER 2 INSERT SCREWS AND TIGHTEN Figure 5 Split Ring Collar Assembly Figure 6 Motor H
15. ousing Installation Www pridemobility com IIl INSTALLATION SPLIT RING COLLAR ADJUSTMENT The split ring collar is the height adjustment for the motor housing See figure 7 The placement of the split ring collar determines the height of the motor housing SECURE NO CLOSER THAN 5 B Lower the collar when more room is needed over 12 5 CM FROM THE TOP OF head to swing the boom arm inside a vehicle THEPOST m Raise the collar when more height is needed to en able a scooter to be lifted into a trunk SCREWS To adjust the split ring collar 1 Loosen the two screws the collar See figure 7 2 Raise or lower the collar to the height you may need 3 Tighten the screws Figure 7 Split Ring Collar BOOM ARM ADJUSTMENT Before adjusting the boom arm lower the lifting hook about 12 in 30 cm This will provide enough slack in the strap to enable the adjustable portion of the arm top tube to be pulled out of the bottom tube to its farthest adjustment hole See figure 8 BOWTIE COTTER PIN TOP TUBE ADJUSTMENT HOLES To adjust the boom arm BOTTOM TUBE 1 Remove the bow tie cotter pin from the adjustment pin and remove the adjustment pin LIFTING Di 2 Slidethetop tube in or out to the desired adjustment HOOK hole 3 Alignthe adjustment holes of the top and bottom tube and reinsert the adjustment pin ADJUSTMENT PIN NOTE Do not force the pin into the adjustment hole
16. purchaser free of charge any of the following parts found upon examination by an authorized representative of Pride Mobility Products Corporation to be defective in material and or workmanship B Mainframe m Electronic switch assemblies m Motor gearbox assembly Warranty service can be performed by an authorized Pride Provider or by Pride Mobility Products Corporation Do not return faulty parts to Pride Mobility Products Corporation without prior consent transportation costs and shipping damage incurred while submitting parts for repair or replacement are the responsibility of the original purchaser WARRANTY EXCLUSIONS Damage caused by B Abuse misuse accident or negligence Improper operation installation maintenance or storage Commercial use or other than intended use Repairs and or modifications made to any part without specific consent from Pride Mobility Products Corporation Circumstances beyond the control of Pride Labor service calls shipping and other charges incurred for repair of the product unless specifically au thorized by Pride There is no other express warranty Implied warranties including those of merchantability and fitness for a particular purpose are limited to one year from the date of purchase and to the extent permitted by law Any and all implied warranties are excluded This is the exclusive remedy Liabilities for consequential damages under all warranties are excluded Some state
17. s the entire elec trical system shuts down WARNING Never attempt to lift WORKING FUSE BLOWN FUSE than 130 Ibs 60 kg with the L amp S Go Go Travel Lift Figure 19 Fuse Replacement To reset the main circuit breaker 1 Allowaminute or so for the electronics to cool 2 Pushin the reset button to reset the breaker If the breaker trips frequently contact your authorized Pride Provider LIFTING STRAP TRAVELS IN OPPOSITE DIRECTION OF BUTTON BEING PUSHED ON HAND CONTROL Before each use check that the lifting strap 15 traveling in the proper direction If the belt travels in the wrong direction when you press either the up or down button you must restore proper lifting strap travel To restore proper lifting strap travel 1 Pullslightly on the strap and operate the lift until the strap is extended completely past the stop warning label 2 Allow the strap to rewind itself Do not allow any twists in the belt Observe the travel ofthe belt it should correspond with the button being pushed on the hand control If you are still experiencing problems contact your authorized Pride Provider 16 Www pridemobility com Go Go Travel Lift VI WARRANTY ONE YEAR LIMITED WARRANTY For one year from the date of purchase Pride Mobility Products Corporation will repair or replace at our option to the original
18. s do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state Please fill out and return the warranty card to Pride This will aid Pride in providing the best possible technical and customer service Go Go Travel Lift www pridemobilitycom 17 18 www pridemobilitycom Go Go Travel Lift NFMANU2803 Pride Mobility Products Corp 182 Susquehanna Ave Exeter PA 18643 1 800 800 8586 www pridemobility com
19. tall the screw into the pilot hole PN N WARNING DO NOT attach the black ground wire to the lift 5 Connectthe harness of wires leading to the battery and ground to the harness that extends from the motor housing black to black and red to red MOTOR HOUSING BLACK GROUND WIRE ATTACH TO CLEAN BARE METAL IN CLOSE PROXIMITY TO LIFT BLACK RED POWER HARNESSES SHEET METAL SCREW 12 1 2 ROUTE RED 4 POWER WIRE CONNECTOR AUTOMOBILE TO BATTERY USE PLIERS OR CRIMPING BATTERY TOOL TO CRIMP Figure 12 Electrical Wiring Connections Go Go Travel Lift Www pridemobility com 13 IV OPERATION LIFTING THE SCOOTER PRESS TO OPERATE LIFT IN PRESS TO OPERATE LIFT A DOWNWARD DIRECTION IN AN UPWARD DIRECTION WARNING Before operating the AN Go Go Travel Lift for the first time A be absolutely sure you have the GEN proper docking device for your scooter 1 Position your scooter with the key removed and the tiller lowered on the ground behind the in stalled lift Be sure that there is ample space be tween the scooter and the vehicle bumper to en sure that the scooter will not hit the bumper while being raised If the scooter is too far from the vehicle s bumper the scooter will be dragged when attempting to lift it 2 Position the boom arm over the scooter 3 Operate the lift use the hand control see fig ure 13 in the downward direction until the lift ing hook reaches the T bar
20. upon you as well as your provider caretaker or healthcare professional in using good judgement If there is any information in this manual which you do not understand or if you require additional assistance for setup or operation please contact your authorized Pride Provider Failure to follow the instructions warnings and notes in this manual and those located on your Pride product can result in personal injury or product damage and will void Pride s product warranty PURCHASER S AGREEMENT By accepting delivery of this product you promise that you will not change alter or modify this product or remove or render inoperable or unsafe any guards shields or other safety features of this product fail refuse or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product SHIPPING AND DELIVERY Before using your Travel Lift make sure your delivery is complete as some components may be individually packaged If you do not receive a complete delivery please contact your authorized Pride Provider immediately Where damage has occurred during transport either to the packaging or content please contact the delivery company responsible INFORMATION EXCHANGE We want to hear your questions comments and suggestions about this manual We would also like to hear about the safety and reliability of your new scooter and about the service you received from your authorized Pride Provi
Download Pdf Manuals
Related Search