Owner`s Manual
Contents
1. I 93S Owner s Manual Low Impact Treadmill page 2 Safety Information Before beginning any fitness program you should have a complete physical examination by your personal physician You should also review this manual and become familiar with how to use the M9 3s Low Impact Treadmill Read and observe the following guidelines when using this treadmill e Read the Owner s Manual and follow all instructions e Assemble and operate the M9 3s treadmill on a solid level surface Locate the treadmill at least 4 feet from walls or furniture Keep the area behind the treadmill clear e Never allow children on or near the M9 3s treadmill Never leave children unsupervised around the treadmill e Check the M9 3s treadmill before each use Do not use the treadmill if it is not completely assembled or is damaged in any way e Keep hands away from moving parts e Do not use the M9 3s treadmill if you weigh over 250 pounds The M9 3s treadmill is built to handle persons up to 250 pounds at speeds up to 9 mph e Wear proper exercise clothing and shoes for your workout no loose clothing Do not wear shoes with heels or leather soles Check the soles of your shoes and remove any embedded stones Tie long hair back e Keep all loose clothing and towels away from the treadmill running surface A treadmill running belt will not stop immediately if an object becomes caught in the belt or rollers e Use the clip provided to attach th2. kph When it leaves the factory the M9 3s is configured to display speed in mph To change this setting follow the instructions found in Specifying MPH or KPH in this section Understanding the Electronic Console The electronic console on the M9 3s lets you control your workout session while providing constant feedback about your progress Use the SPEED and INCLINE keys to govern speed and degree of incline An electronic LED display flashes information about elapsed time speed distance covered degree of incline and total calories burned Photo 6 shows the M9 3s console An explanation of each of the keys on the keypad follows the photograph Photo 6 The M9 3s electronic console INCLINE With the M9 3s treadmill you can specify an incline from 0 to 10 percent Simply press the INCLINE amp key to increase the incline and the INCLINE W key to decrease the incline until you reach the desired percentage Note The number shown on the display will change faster than the elevation motor can respond After you select an incline there may be a brief delay before the specified elevation is reached If you need to stop the elevation motor simply press the STOP key This will also stop the running belt The display will indicate the incline actually reached STOP Anytime during a workout or when you finish your workout or at press the STOP key to slow the running belt to a safe stop You can also stop the trea
3. EA 14 EAE 14 ee E E mee 17 Ll ama meas 19 Tuori 20 area 21 Neate ete oan Be 22 Getting the Most Out of Your Workout E aa 24 How Long Should Exercise f 25 How Often Should Exercise cccccseeeeereesscteeeeeeees 25 Maintenance Cleaning the Treadmill J ccccccccccssseeeceeesseeeeesssieeeeeeees 26 Aligning the Running Belt ecceeeeeeeneeeeeeenneeeeeeeaees 27 Getting SERVICE sides codessdecsecevarsctetsteldcteasdothdvenceadteccdetenaieates 28 Quality by Design Before You Begin Congratulations You now own one of the newest most technologically ad vanced electronic treadmills available The M9 3s Low Impact Treadmill belongs to Precor s exciting M series of exercise equipment a superior combination of high technology and ergonomics The M9 8s treadmill lets you exercise safely in the convenience of your own home Turn on the M9 3s treadmill specify your weight and belt speed and begin your workout As you walk or run the unique running bed protects vulnerable knees and ankles by absorbing much of the impact of each step Specially designed cylinders absorb the impact while providing a smooth consistent running surface For quick motivating information about your progress glance at the easy to read control panel This console provides information about your elapsed time speed distance covered degree of incline and total calories burned If you should encounter a problem during your wor
4. or kilometers per hour kph When the M9 3s is shipped from the factory it displays speed in mph You can easily change this setting by following the steps below The M9 3s treadmill will retain your selection even when it is turned off or unplugged You can change your selection at any time by repeat ing these steps CAUTION Do not stand on the belt during this procedure 1 Place the magnetic safety key on the ACTIVATE position of the electronic console Walk to the rear of the treadmill and turn the power switch to ON The magnetic safety key must be placed in the ACTIVATE position before you can turn on the treadmill 2 Straddle the running belt with your feet firmly planted on the right and left staging platforms Stand close enough so you can extend your arm and touch the keypad Use the clip on the magnetic safety key to attach it to your clothing at your waistline 3 When the prompt Enter Weight appears press and hold the green SPEED key and the SCAN ENTER key Release both keys 4 Select mph by pressing SPEED 4 or select kph by pressing SPEED W You can continue your workout by following the appropriate steps found in Running on the M9 3s Treadmill or stop the treadmill by pulling on the magnetic safety key and turning the treadmill OFF Getting the Most Out of Your Workout A workout on the M9 3s Low Impact Treadmill provides excellent and efficient cardiovascular conditioning while strengthening and toni
5. page 15 page 16 Diagram 1 Overview of Pre Programmed Courses Walk 1 Walk 2 Walk 3 Walk 4 Walk 5 Run 1 D Run 2 0 1 2 Run 3 J Run 4 E cl Run 5 6 Atthe Select miles kilometers prompt specify the length of your course Press the arrow keys to choose distance the display moves in 5 increments from 5 to 99 5 miles kilometers Press SCAN ENTER when the desired distance is shown If you see Select Time scroll across the display specify the length of your workout Press the arrow keys to choose time the display moves in 1 minute increments from 5 to 99 minutes Press SCAN ENTER when the desired time is shown Note You can change the Select Distance prompt to Select Time if you prefer to measure your workout by time Follow the procedure in Selecting the Time or Distance Prompt at the end of this section 7 Stand on the running belt with one hand on the handrail prepare to start walking With your other hand press the SPEED arrow keys until you reach your desired speed Now simply continue working out Your workout will continue until the specified distance or time is reached or until the STOP key is pressed Anytime during your workout you can change your speed When you are finished working out hold onto the handrail and press STOP The treadmill will come to a safe stop Be sure to remove the magnetic safety key from your clothing and return it t
6. the Select Distance or Select Time prompt after you specify a course see Step 6 of the procedure Using a Pre Programmed Course The default measurement is distance To change the prompt follow these instructions 1 Place the magnetic safety key on the ACTIVATE position of the electronic console Walk to the rear of the treadmill and turn the power switch to ON The treadmill will not operate unless the safety key is in the ACTIVATE position 2 Straddle the running belt with your feet firmly planted on the right and left staging platforms Stand close enough to the electronic console so you can extend your arms and touch the keypad 3 Using the clip provided securely attach the magnetic safety key to your exercise clothing at your waistline where it will not interfere with your workout 4 When you see Enter Weight scroll across the display press the SPEED amp key and SCAN ENTER key simultaneously 5 When you see Press 4 for MPH or W for KPH press the SPEED amp key If you are using kilometers press the SPEED W key After you press the SPEED amp key the message MPH and Miles Mode scrolls across the display 6 When you see Push for Distance W for Time or STOP for Ask press the appropriate key after answering one of the following if then scenarios your workout measured by distance e press the key your workout measured by time e press W the key the op
7. the threaded hole in the fitting If the holes do not align slide the 5 32 hex key into the threaded hole and turn the fitting so the holes align Take a 1 4 x 1 2 socket head screw from the hardware kit and hand thread it into the fitting Tighten the screw with the 5 32 hex key 14 To attach the opposite handrail repeat steps 10 through 13 Photo 5 Attach handlebars to running bed assembly 15 Attach the labels provided in the hardware kit over each upper handlebar bolt 16 If you need to move the treadmill ask for assistance from another person Roll the treadmill on its front wheels to the new location by lifting the rear end of the unit CAUTION Do not attempt to bypass the three prong plug with an adapter for a non grounded outlet 17 Plug the power cord into a grounded 120v household outlet with a dedi page 10 cated 20 amp circuit breaker Using the M9 3s Low Impact Treadmill As simple as using the M9 3s Low Impact Treadmill may seem you should read this section so that you can use it safely and effectively This section provides information about the electronic console displays and instructions on how to use the treadmill during a workout For information about the electronic console see Understanding the Electronic Console for information about working out with the M9 3s treadmill see Working Out on the M9 3s Treadmill The M9 3s can indicate speed in miles per hour mph or kilometers per hour
8. the base of the treadmill flat on the floor Loosen the top two bolts one full turn This will allow the control panel assembly to shift and rest securely on the running bed assembly You may need to rock the control panel assembly gently so it will seat properly on the four bolts The lower edges of the control panel assembly should be flush with the base of the treadmill Firmly tighten all four bolts with the 5 16 hex key and insert the white hole plugs into the mounting bolt access holes To mount the upper handrails use a flathead screwdriver to remove the 1 bolt from the RIGHT side of the upper control panel assembly Note LEFT and RIGHT are determined while standing behind the tread mill facing toward the front of the machine Place the upper end of the RIGHT handrail into the hole in the right column of the control panel assembly Insert the handrail over the steel bar with the threaded hole See Photo 4 Replace the 1 bolt by feeding it through the hole in the handrail and into the threaded hole in the steel bar To align the holes you may have to rotate the center bar located under the control panel Using the flathead screwdriver tighten the bolt until it feels snug but do not overtighten page 9 Photo 4 Insert handlebars into the control panel assembly 13 Slide the lower end of the RIGHT handrail onto the black fitting located on the side of the frame See Photo 5 Align the hole in the handrail with
9. age and level of fitness Refer to Diagram 3 to determine your training zone Keep in mind that this zone is an approximation to be used as a guideline individual heart rates vary according to several physiological factors To determine your training zone or target heart rate find your age and fitness level on the chart and then find the line where they intersect For example if you are 35 years old your training heart rate at the intermediate fitness level is 157 beats per minute Remember this number this is the pulse rate you should try to maintain as you work out Diagram 3 Your Heart Rate HEART RATE TRAINING ZONES 2 lt ae kK oc ui ae ee oO gt 34v LYV3H FTEVNIVLLLY WNIWIXVIN YOUR AGE To determine your heart rate take your pulse at a place that you can reach easily and comfortably while you exercise Typical locations for measuring heart rate are directly over the heart on the left side of the chest on either side of the neck over the temple or on the thumb side of either wrist Wherever you measure your pulse make sure that you use your index and middle fingers not your thumb Your thumb has a strong pulse which can affect your heart rate reading Once you locate your pulse look at a clock with a second hand and count the beats for six seconds Multiply that number by 10 to determine the total number of beats per minute For example if you count 14 beats over six seconds t
10. ard until the upper end is clear of the hole 2 Rotate the lever right or left and insert the end of the lever into the hole at the desired setting Photo 7 Control lever for adjusting impact reduction page 20 Running on the M9 3s Low Impact Treadmill Before using the M9 3s Low Impact Treadmill for an actual workout we recom mend that you follow these instructions and go through a preliminary demon stration of the unit This will make you more familiar with the unit when you begin your first workout When using the treadmill follow these general guidelines e At the beginning of a workout take several minutes to bring your heart rate into your training zone which is shown in Diagram 3 later in this manual After your workout walk slowly for several minutes to cool down your body and lower your pulse rate e Attach the magnetic safety key to your clothing before each workout Use the clip provided on the end of the cord to attach the key Then if you encounter difficulties or want to end your workout you can easily stop the running belt by pulling on the cord e Gently stretch your lower body and back after a workout to help prevent stiffness or soreness To use the treadmill follow the instructions below Remember when you use the electronic console hold onto the handrail to maintain your balance You should also use the handrail whenever you slow down or stop the treadmill Important Before working out o
11. c safety key on the ACTIVATE position Walk to the front of the treadmill and turn ON the treadmill using the ON OFF switch The treadmill will not turn on unless the safety key is in the ACTIVATE position 2 Straddle the running belt with your feet firmly planted on the right and left staging platforms Stand close enough to the electronic console so you can extend your arms and touch the keypad Using the clip provided securely attach the magnetic safety key to your exercise clothing at your waistline where it will not interfere with your workout When you see Enter Weight scroll across the display specify your weight using the SPEED arrow keys The number on the display moves in 5 pound increments up or down depending on the arrow key pressed Use A to increase and W to decrease the weight displayed When the correct weight is displayed press SCAN ENTER This information allows the M9 3s to calculate how many calories you burn during your workout The treadmill automatically remembers the last weight entered During your next workout you restore your weight from the treadmill s memory by simply pressing SCAN ENTER at the Enter Weight prompt However if someone else has used the treadmill prior to your workout you need to re enter your weight Note The prompt Press Enter to Begin appears after 10 seconds if you have not pressed SCAN ENTER This prompt continues to scroll across the display every 10 seconds unti
12. d gradually For example in the beginning you may simply want to specify the same speed for both Work and Rest intervals Then to increase your effort level change to a higher speed for your Work interval e Ifyou are training with the goal of maintaining a constant pace when on level ground or grade specify the same speed for both Work and Rest intervals Then gradually increase the incline during the Work interval until you can maintain a constant pace page 13 page 14 Working Out on the M9 3s Treadmill Before using one of the pre programmed courses Interval Mode INTV or the Manual MAN L options on your treadmill we recommend that you follow the instructions given here and go through a preliminary demonstration of the features Then you will be familiar with the treadmill when you begin your workout When using the treadmill follow these general guidelines e At the beginning of a workout take several minutes to bring your heart rate into your training zone which is shown in Diagram 3 later in this manual e After your workout walk slowly for several minutes to cool down your body and lower your pulse rate Using the clip provided attach the magnetic safety key to your clothing before each workout Then if you encounter difficulties or want to end your workout you can easily stop the running belt by pulling on the cord e Gently stretch your lower body and back after a workout to help prevent stiffness o
13. d on the treadmill as it runs the belt does not need adjustment Skip to Step 7 However if the belt runs off center you need to adjust it Continue to Step 4 4 Turn OFF the treadmill Wait for the running belt to come to a complete stop 5 Using the right hand adjusting screw located at the front of the treadmill see Photo 9 adjust the belt accordingly e To move the belt left turn the screw 1 4 turn clockwise using a hex key To move the belt right turn the adjusting screw 1 4 turn counterclock wise Do not turn the adjusting screw more than 1 4 turn at a time Important Before making each adjustment make sure the treadmill is OFF and the belt has completely stopped page 27 page 28 Photo 9 Aligning the running belt Right hand adjusting screw 6 After adjusting the belt let the treadmill run for a couple of minutes to check the alignment and to make sure the belt is stable If more correction is required repeat steps 4 and 5 by turning the adjusting screw another 1 4 turn then check the result If you overcorrect turn the screw in the opposite direction Refer to Photo 9 7 Once the belt is properly aligned press the STOP key to stop the belt Getting Service Do not attempt to service the M9 3s Low Impact treadmill yourself except for performing the maintenance tasks as described in this manual For further information about product operation or service contact an authorized Precor d
14. dmill by moving the magnetic safety key from the ACTIVATE to the OFF position ACTIVATE To protect you during your workout you must attach the magnetic safety key to your clothing during each workout Before turning ON the treadmill place the key in the ACTIVATE position on the console Then if you encounter a problem during your workout simply pull on the safety key s cord to stop the running belt If you stop the treadmill using the safety key replace the key on ACTI VATE and turn the treadmill back on to continue your workout page 11 page 12 OFF After completing your workout by pressing STOP place the magnetic safety key on the OFF position You can also stop the treadmill by moving the mag netic safety key from the ACTIVATE to the OFF position Remove and store the safety key to ensure children or an unqualified person will not be able to activate the treadmill SCAN ENTER Use the SCAN key to move through the display functions TIME SPEED DISTANCE covered degree of INCLINE and total CALORIES burned When the display is set to SCAN it provides feedback about all the functions in a sequential order To change from SCAN mode to a constant display of a specific function press the SCAN key once The cursor moves to the DISTANCE mode Continue to press the SCAN key until the cursor indicates the desired function SPEED The SPEED AW keys let you control the speed of the running belt Use amp to inc
15. e magnetic safety key to your clothing before each workout By pulling on this key you can easily stop the running belt if you encounter difficulties or want to end your workout Note You need to place the magnetic safety key on the ACTIVATE posi tion of the electronic console before you can turn on the treadmill e Use care when getting on or off the M9 3s treadmill Use the handrails whenever possible Do not get on or off the treadmill when the running belt is moving e Before starting the running belt straddle the belt by placing your feet firmly on the right and left staging platforms You should also step off the belt and onto the staging platforms after turning off the running belt e Never turn ON the treadmill when someone is standing on the machine Keep your body and head facing forward Never attempt to turn around on the treadmill when the running belt is moving Do not rock the unit Do not stand or climb on the handrails electronic console or hood Do not set anything on the handrails electronic console or hood Never place liquids on any part of the treadmill Prevent electrical shock by keeping all electrical components such as the motor power cord and ON OFF switch away from water or other liquids Do not use accessory attachments that are not recommended by the manufacturer such attachments might cause injuries Do not attempt to service the M9 3s treadmill yourself This treadmill does not have any u
16. e option and specify 6 at the prompt you can choose from 5 to 99 5 miles in 5 mile increments if you want to run 20 minutes select the time option and specify 20 at the prompt you can choose from 5 to 99 minutes Please note that distance is the default option If you want to measure your workout by time you must specify that option following the procedure in Selecting the Time or Distance Prompt in this section To help you monitor your workout press the SCAN ENTER key The treadmill displays a readout on distance time speed calories and incline This display also appears at each transition point Interval Training with Interval Mode Besides choosing a pre programmed course you can choose the Interval Mode option Use this option to design your own interval training program Interval training provides numerous benefits Since interval training segments the workout into smaller components a 20 or 30 minute workout seems to pass more quickly In addition studies have shown that it is a more efficient method for achieving aerobic benefits you start seeing improved cardiovascu lar fitness much sooner with less effort Recent studies also show that people who interval train are more likely to stick with their fitness program Interval training consists of brief periods of elevated activity followed by brief periods of reduced activity The Interval Mode option alternates between 60 seconds of Rest and 60 seconds of Wor
17. ealer or a Precor Factory Authorized Service Company To locate the Precor dealer nearest you call 1 800 4 PRECOR PRECOR 2 wd D Precor Incorporated Precor and M registered trademarks of Precor Incorporated P N 33045 102 P O Box 3004 1990 Precor Incorporated Rd 1990 6 92 Bothell WA USA 98041 3004 Specifications subject to change without notice 1 800 4 PRECOR
18. elt to remain centered and it assures the smooth operation of the treadmill The belt is aligned at the factory before shipment However during shipment or by using the treadmill on an uneven surface the belt may move off center Realigning the belt takes a few simple adjustments If you are unsure about this procedure call your author ized Precor dealer for service Important If you notice the belt needs alignment make the adjustments at once Failure to do so may cause the belt to tear or fray this damage is not covered by warranty CAUTION Special care must be taken when aligning the running belt Remove any loose clothing and tie back your hair before adjusting the belt Be very careful to keep your fingers or any other object clear of the belt and rollers especially in front of the deck and behind the roller The treadmill will not stop immediately if any object becomes caught in the belt or rollers The M9 3s Low Impact Treadmill is designed to carry people who weigh up to 250 pounds at speeds from 5 to 9 miles per hour To align the running belt take the following steps 1 Place the magnetic safety key on the ACTIVATE position and turn ON the treadmill using the switch located on the rear of the M9 3s 2 Press and hold the SPEED increase key until the belt speed reads 6 0 mph on the control panel display 3 Walk to the front of the treadmill and observe the operation of the belt for about a minute If the belt is centere
19. ft the control panel assembly and position it at the front of the running bed 4 Align the tab on the side of the ribbon cable connector with its correspond ing receptacle See Photo 1 on the next page Connect the ribbon cable by making sure that all the pins are aligned and fully engaged page 7 Photo 1 Connect ribbon cable Running Bed Assembly Ribbon Cable Control Panel Assembly Foam blocks 5 To place the control panel assembly onto the front of the running bed take the following steps Refer to Photo 2 for clarification a Locate the four mounting bolts on the running bed assembly Use the hex key provided to unscrew the mounting bolts until four or five threads are visible b Position the control panel assembly in front of the running bed assem bly Line up the four mounting bolts on the running bed with the four keyholes in the control panel assembly Place the control panel assem bly onto the mounting bolts making sure to feed the excess ribbon cable into the frame rail to avoid pinching the ribbon See Photo 2 Photo 2 Place control panel assembly onto mounting bolts Frame rail Mounting Bolts Keyholes 6 Slide the control panel assembly upward to lock the mounting bolts in place Tighten the top two bolts using the 5 16 hex key from the hardware kit See Photo 3 page 8 Photo 3 5 16 hex key Secure top two bolts 10 11 12 Remove the foam blocks and set
20. he total number of beats per minute is 140 Compare the total number of beats with your training zone as identified in Diagram 3 If necessary increase or decrease your activity level to bring your heart rate into your training zone You can increase your activity level by decreasing the resistance and stepping at a higher cadence Similarly raising the resistance and decreasing your steps per minute will lower your heart rate Remember your heart rate is the definitive measure of how hard you are working Regardless of your fitness level avoid doing too much too soon Setting the resistance cylinders too far forward stepping too deeply taking large steps or stepping too quickly for too long are common errors Give yourself time to become familiar with your climber and improve your fitness level Then you can gradually decrease your resistance level and increase your stepping cadence to make your workouts more challenging How Long Should Exercise The length of each exercise session depends on your fitness level Exercise physiologists have determined that to attain cardiovascular benefits from exercise you should maintain your heart rate in the training zone for at least 15 minutes This is in addition to your warm up time and does not include cool down You should always allow several minutes to bring your heart rate into the training zone by starting out slowly and gradually increasing the work level Similarly use several minute
21. k During the Rest interval you can walk or jog slowly during the Work interval you can stride quickly or run You specify the Rest and Work speeds at the beginning of the first interval The microprocessor remembers the speed and returns to that speed at the begin ning of each subsequent Rest or Work interval With the M9 3s treadmill you can also specify the incline for the Rest and Work intervals allowing you to increase and decrease your workload using both speed and incline The microprocessor remembers the incline you set for each interval and returns to that incline at the beginning of the next interval At any point during the workout you can change the speed and incline of the current interval For example if you realize that 8 miles per hour is a little faster than you prefer during a Work interval simply use the SPEED key to reduce the speed The microprocessor remembers the new speed for the next Work interval To help you monitor your workout the treadmill automatically displays a readout on distance time speed calories and incline This display occurs every thirty seconds and at each transition point To randomly display this readout anytime during your workout press the SCAN ENTER key Some Tips for Using Interval Mode Here are some suggestions that may help you incorporate the Interval Mode into your workout e Ifyou are starting an exercise program the Interval Mode option can help you increase your workloa
22. kout you can stop the treadmill by pulling on the cord attached to the magnetic safety key Built with the highest quality materials the M9 3s Low Impact Treadmill pro vides the motivation and challenge you need to help you achieve your fitness goals for years to come About this Manual This manual explains how to assemble use and maintain the M9 3s Low Impact Treadmill You will also find a basic explanation of aerobic conditioning and information about tailoring a fitness program to your needs If you encoun ter problems while installing or using the M9 3s Low Impact Treadmill refer to this manual for trouble shooting information This manual uses the following conventions Note Contains additional information that applies to the preceding text Important Indicates information that you should pay special attention to CAUTION Indicates steps or information necessary to prevent harm to yourself or damage to the equipment You do not need any special knowledge or experience to set up an M9 3s Low Impact Treadmill However you must carefully review and follow the instruc page 5 page 6 Unpacking the M9 3s Treadmill The M9 8s treadmill is carefully inspected before shipment so it should arrive in good operating condition Precor ships the unit in four pieces as listed below e running bed assembly e control panel assembly e handrails e hardware kit contents described below Carefully unpack the parts from the
23. l you press SCAN ENTER At the Select Course prompt choose your workout mode either Manual MAN L Interval INTV or one of the ten pre programmed courses Press the arrow keys until you see the desired mode or course then press SCAN ENTER Since these instructions explain how to use a pre programmed course select a course WALK 1 through RUN 5 To help you decide on which course you want to use Diagram 1 on the following page gives an overview of each course Each course combines 5 mile segments with a set series of inclines The percent of incline and the frequency with which inclines are encountered indicate the difficulty of the course For example WALK 1 has inclines ranging from 0 to 3 percent RUN 5 has inclines ranging from 0 to 10 percent The microprocessor simply repeats the 5 mile segments until the workout ends Manual Mode is the default selection for the Select Course prompt After specifying your mode you will not need to specify the mode again The microprocessor automatically remembers the last mode selected At your next workout simply press SCAN ENTER at the Select Course prompt If another person uses the machine you might need to specify the mode again as described in this step Note If you do not press SCAN ENTER to select a course after 10 seconds the prompt Press Enter appears This prompt continues to scroll across the display every 10 seconds until SCAN ENTER is pressed
24. ly and efficiently Typical maintenance tasks include cleaning the treadmill and adjusting the running belt Instructions for both procedures are provided in this section Cleaning the M9 3s Low Impact Treadmill Your Precor precision treadmill relies on low friction for efficient operation To keep the friction low the treadmill must be as clean as possible Photo 8 illustrates the locations that should be kept clean CAUTION Turn OFF the treadmill and unplug the power cord before cleaning Before a workout use a damp soft cloth to clean the staging platforms running bed and under the belt as far as you can easily reach This removes any dirt or dust that might affect the smooth operation of the treadmill Photo 8 Keep these areas on the M9 3s treadmill clean Frame Running belt Margins of running bed Vacuum underneath the unit every week to prevent the accumulation of dust and dirt on the running belt Periodically clean the treadmill s frame electronic console and running belt using mild soap and water To clean the running belt use a soft nylon scrub brush Do not pour water or spray liquids on the control panel Allow the treadmill to dry completely before using page 26 Aligning the Running Belt The M9 3s Low Impact Treadmill is designed so that the running belt automati cally centers itself on the running bed when the treadmill is in use Proper belt alignment is important because it allows the b
25. n the treadmill make sure the running belt is correctly aligned Correct alignment is critical to the smooth and safe operation of the treadmill For more information see Aligning the Running Belt 1 Place the magnetic safety key on the ACTIVATE position of the electronic console Walk to the rear of the treadmill and turn the switch to ON The treadmill will not operate unless the safety key is in the ACTIVATE posi tion 2 Straddle the running belt with your feet firmly planted on the right and left staging platforms Stand close enough to the electronic console so you can extend your arms and touch the keypad 3 Using the clip provided securely attach the magnetic safety key to your exercise clothing at your waistline where it will not interfere with your workout 4 When you see Enter Weight 125lb scroll across the display specify your weight using the SPEED arrow keys The number on the display moves in 5 pound increments up or down depending on the arrow key pressed Use A to increase and W to decrease the weight displayed When the correct weight appears press SCAN ENTER This information allows the M9 3s to calculate how many calories you burn during your workout The treadmill automatically remembers the last weight entered During your next workout you restore your weight from the treadmill s memory by pressing SCAN ENTER at the Enter Weight prompt However if some one else has used the treadmill prior to
26. ng all the major muscle groups in the lower body Darkened areas in Diagram 2 indicate the muscles that can be improved To get the most out of each workout a general understanding of the principles behind aerobic training is invaluable The best source of fitness information is your specialty fitness dealer In addition to providing information on which exercise equipment is the best for your individual needs your specialty fitness retailer can provide useful advice on training technique and exercise physiol ogy Your retailer can also recommend good books on these subjects Diagram 2 Muscles in the body 1 Trapezius 2 Deltoid 3 Pectorals 4 Rhomboids 5 Triceps 6 Biceps 7 Latissimus Dorsi 8 Forearm Flexors Extensors 9 Abdominals 10 Erector Spinae 11 Gluteals 12 Hip Flexors 13 Quadriceps 14 Hamstrings 15 Gastrocnemius Soleus 16 Peroneus Longus Brevis To help you get started in planning and carrying out your fitness program this section provides some basic information on aerobic exercise such as how hard you should work out how long each session should be and how often you need to exercise to benefit from a regular program page 23 page 24 How Hard Should I Exercise Studies show that to achieve the benefits of aerobic exercise it is necessary to work out hard enough raise your heart rate to a certain minimum level called a training zone Your training zone depends on your
27. ng the SPEED arrow keys The number on the display moves in 5 pound increments up or down depending on the arrow key pressed Use A to increase and W to decrease the weight displayed When the correct weight is displayed press SCAN ENTER This information allows the M9 3s to calculate how many calories you burn during your workout The treadmill automatically remembers the last weight entered During your next workout you restore your weight from the treadmill s memory by pressing SCAN ENTER at the Enter Weight prompt However if some one else has used the treadmill prior to your workout you need to re enter your weight Note The prompt Press Enter to Begin appears after 10 seconds if you have not pressed SCAN ENTER This prompt continues to scroll across the display every 10 seconds until you press SCAN ENTER At the Select Course prompt choose your workout mode either Interval INTV Manual MAN L or one of the ten pre programmed courses WALK 1 through RUN 5 Press the arrow keys until you see the desired mode or course then press SCAN ENTER Since these instructions explain how to use the Interval Mode select INTV y page page 18 Manual Mode is the default selection at the Select Course prompt After specifying your mode you will not need to specify the mode again The microprocessor automatically remembers the last mode selected At your next workout simply press SCAN ENTER at the Select C
28. o the OFF position or remove entirely and store in a safe place to guard against use by children or persons unfamiliar with the treadmill Note If desired you can cool down before ending your workout by press ing STOP twice in quick succession The treadmill will stop and enter the Manual Mode allowing you to specify the speed and incline of your cool down period Using Interval Mode To use the Interval Mode option follow the instructions below Remember when you use the electronic console hold onto the handrail to maintain your balance You should also use the handrail whenever you speed up slow down or stop the treadmill CAUTION If this is the first time you have operated this treadmill DO NOT STAND on the running belt until you become familiar with M9 3s operations 1 Place the magnetic safety key on the ACTIVATE position of the electronic console Walk to the rear of the treadmill and turn the switch to ON The treadmill will not operate unless the safety key is in the ACTIVATE posi tion Straddle the running belt with your feet firmly planted on the right and left staging platforms Stand close enough to the electronic console so you can extend your arms and touch the keypad Using the clip provided securely attach the magnetic safety key to your exercise clothing at your waistline where it will not interfere with your workout When you see Enter Weight scroll across the display specify your weight usi
29. original shipping container CAUTION This unit weighs over 150 pounds To avoid back strain and to ensure the safety of the unit and yourself we suggest that you drop the sidewalls of the box and slide the running bed assembly from the box rather than lifting the running bed assembly from the box After unpacking the treadmill open the hardware kit and make sure that you have the following items two 1 4 x 1 2 long socket head screws __ four white hole plugs two 2 1 2 x 1 3 8 black labels one 3 16 hex key one 5 32 hex key one 5 16 hex key one magnetic safety key If any items are missing contact your authorized Precor dealer For the dealer nearest you call 1 800 4 PRECOR Important The packaging for this equipment was designed to protect it during shipment Please store the original packaging in a safe place in case you need to ship the M9 3s treadmill in the future Setting Up the M9 3s Low Impact Treadmill tions in this manual If you do not assemble and use this treadmill according to the following guidelines you could void the Precor warranty CAUTION Two persons are recommended to install the lift column which is part of the assembly procedure Installation Requirements Follow these installation requirements when installing the treadmill e Set up the M9 3s treadmill on a solid flat surface Do not install the treadmill on deeply padded plush o
30. ourse prompt If another person uses the machine you might need to specify the mode again as described in this step Note If you do not press SCAN ENTER to select a course after 10 seconds the prompt Press Enter appears This prompt continues to scroll across the display every 10 seconds until SCAN ENTER is pressed At the Enter Rest Speed and Incline prompt stand on the running belt with one hand on the handrail prepared to start walking With your other hand press the SPEED arrow key and Incline arrows until you reach a comfortable rest speed and incline either running or walking When the desired speed is displayed release the arrow and simply continue working out you do not need to press SCAN ENTER Once you set your Rest speed and incline the microprocessor remembers that speed and returns to it at the beginning of each Rest interval until you change the speed or end your workout When you see Enter Work Speed and Incline scroll across the display specify your Work speed and Incline With one hand on the handrail use the other hand to press the SPEED arrow keys and Incline arrows until the desired Work speed and Incline is shown Then let go of the handrail and continue working out you do not need to press SCAN ENTER You can specify a speed up to 9 miles an hour The microprocessor remembers the specified Work speed and returns to it at the beginning of each Work interval until you change the speed o
31. r shag carpeting due to possible damage to the carpet and machine If the treadmill is placed on a carpeted surface place a piece of heavy cardboard plywood or other smooth flat surface under the unit to protect the carpet and treadmill Locate the treadmill at least 4 feet from walls and furniture Be sure to provide ample space in front of the machine to allow easy access to the ON OFF switch Open space to the sides and back of the machine makes for a safer mount and dismount and easier belt adjustment e Use a standard 120 volt household outlet Precor recommends that you plug the treadmill into an outlet with a dedicated 20 amp circuit breaker The treadmill is equipped with a 20 amp circuit breaker to protect the electrical and electronic components from sustained overloads and an integral 3 prong plug grounded to provide for your safety and to protect the machine CAUTION Do not remove or otherwise bypass the 3 prong plug with an adapter in order to use a non grounded outlet Assembly Instructions To assemble the M9 3s treadmill take the following steps 1 Make sure that the treadmill is unplugged and turned OF Do not assemble the M9 3s treadmill if it is plugged in or turned ON 2 After unpacking the M9 3s treadmill place the front of the running bed assembly on the foam blocks provided in the packaging so that the front edge is about 1 1 2 off the floor Cut and discard the cable ties holding the front axle 3 Li
32. r soreness Pausing Your Workout You can pause your workout at any time by pressing STOP briefly To continue your workout use the SPEED arrow keys to reset your speed When using Interval Mode you must re enter the speed of the mode you were in when you paused your workout For example if you paused your workout during the Rest interval you must reset the speed for that inter val In this example you would not need to reset the speed for the Work interval since the microprocessor will remember the previously specified speed Ending Your Workout To end your workout press STOP This will slow the treadmill to a gradual stop The display will begin to scan and allow you to review the total time distance and caloric burn of your workout If you press STOP twice in quick succession your treadmill will go to manual mode allowing you to do some cool down exercise To reset your treadmill press the STOP key and hold it for several seconds This clears all data Using a Pre Programmed Course To use a pre programmed course follow the instructions below Remember when you use the electronic console hold onto the handrail to maintain your balance You should also use the handrail whenever you speed up slow down or stop the treadmill CAUTION If this is the first time you have operated this treadmill DO NOT STAND on the running belt until you become familiar with M9 3s operations 1 On the electronic console place the magneti
33. r stop your workout Each Rest and Work interval lasts 60 seconds The display automatically counts down to the next interval When the count reaches 30 seconds the display changes and gives information about distance traveled time elapsed speed calories burned and percent of incline You can also get this information at any time by pressing SCAN ENTER When the treadmill changes intervals it informs you with Going to Rest Speed and Incline or Going to Work Speed and Incline messages on the display Anytime during an interval you can change the incline using the IN CLINE arrow keys Once you specify an incline for an interval the micro processor in the M9 3s treadmill remembers that incline and returns to it each time the interval is repeated When you are finished working out hold onto the handrail and press STOP The treadmill will come to a safe stop Be sure to remove it the magnetic safety key from your clothing and return it to the OFF position or remove entirely and store in a safe place to guard against use by children or persons unfamiliar with the treadmill Note If desired you can cool down before ending your workout by press ing STOP twice in quick succession The treadmill stops and enters Manual Mode allowing you to specify the speed and incline of your cool down period Selecting the Time or Distance Prompt When using a pre programmed course you can measure your workout by distance or time You see
34. rease speed and W to decrease speed Pressing starts the running belt at 5 mph if you continue to press this key speed increases in 2 mph 3 kph increments up to 9 0 mph 14 4 kph Pressing W decreases the belt speed at the rate of 6 mph 1 kph every second Anytime during your workout you can see how many minutes it takes you to walk or jog a mile or kilometer To use this feature simultaneously press both SPEED AW keys and the information appears on the screen When you release both keys the speed display returns to the per hour measurement you originally chose mph or kph Pre Programmed Courses The M9 3s treadmill offers a series of ten pre programmed courses These courses are designed for anyone interested in working out whether you are walking running starting a fitness program or are already in shape For each course you choose the speed and distance the incline is pre determined according to the level of the course Choose from WALK 1 to WALK 5 or from RUN 1 to RUN 5 Each course takes the user through a set series of incline intervals with inclines varying according to the level of the course The higher the number the more vigorous the course For example WALK 1 takes the user through inclines ranging from 0 to 3 percent grade RUN 5 has inclines ranging from 0 to 10 percent You can also specify how you want your workout measured in distance or time For example if you want to run 6 miles choose the distanc
35. s of light exercise after the workout to bring your heart rate down to near resting level The higher your fitness level the longer your should maintain your heart rate in the training zone between 20 and 30 minutes Beginners should always start slowly and gradually get their sessions up to 20 minutes or more Walking and running are excellent aerobic exercises that condition the heart and lungs while improving strength and tone in the thighs calves and hips The best aerobic exercises involve the continuous rhythmic repetitive move ment of large muscle groups When you exercise you need to work out hard enough long enough and often enough to achieve your desired results How Often Should Exercise Research indicates that aerobic sessions of 20 minutes or more should be done at least three to five times a week to obtain significant cardiovascular benefits Most experts agree that sensible eating habits and regular aerobic exercise are the keys to weight control and fitness A recent study which tracked several subjects over a period of years conclusively shows that exercise not dieting is the key factor to successful long term weight loss To help you get the most out of your workout this section provides suggestions about aerobic exercise Following these suggestions will help you reach your fitness goals page 25 Maintaining the M9 3s Treadmill The M9 3s treadmill requires little maintenance to keep it running smooth
36. ser serviceable parts See Getting Service in Section 5 for service information Turn OFF the treadmill and wait for the running belt to come to a complete stop before adjusting or working near the rear roller Do not make any adjustments to the running belt when someone is standing on the machine This treadmill is manufactured with six safe fail off systems If the tread mill encounters a problem it will trigger a fail off system allowing the running belt to come to a gradual stop Continued use of the treadmill after a fail off system occurs is not recommended Instead have your treadmill serviced as described in Getting Service in the maintenance section of this manual Do not overexert yourself or work to exhaustion Stop your workout immediately if you feel any pain or abnormal symptoms and consult your physician Precor treadmills are designed for the enjoyment of the serious runner as well as the dedicated walker By following the above precautions and using good common sense you will have many safe and pleasurable hours of healthful exercise with your Precor M9 3s Low Impact Treadmill page 3 page 4 Table of Contents Quality by Design ise titel EEA 5 About this Manual cceccecceceeeeeeeeeeeeeeeeeeeeaeeeeeeeeenen 5 PAA ar ete E T 6 Setting Up the M9 3s Low Impact Treadmill cess t eR E a 7 EEE E E NE 7 Using the M9 3s Low Impact Treadmill e 11 EIEE 12 aeara ta 13 ENTIA TAEA 13 ET
37. tion of selecting time or press STOP distance prior to each workout After you press an arrow key the display shows Distance Mode or Time Mode depending on the key pressed The message Enter Weight scrolls across the display 7 Either continue with your workout or turn off the treadmill by pulling the safety key off the ACTIVATE position If you turn off the treadmill be sure to remove the magnetic safety key from your clothing and return it to the OFF position or remove entirely and store in a safe place to guard against use by children or persons unfamiliar with the treadmill page 19 Adjusting the Stiffness of the Running Bed The M9 3s Low Impact Treadmill is specially designed to allow you to adjust the amount of impact reduction Three levels are available Level 1 Hard Level 2 Medium and Level 3 Soft The level you choose depends on your weight and running style To choose the best impact reduction level for you use the treadmill with the running bed set at each of the settings Then select the level that suits your exercise style the best Important Do not adjust the bed impact reduction level when someone is standing walking or running on the treadmill Be sure to turn OFF the treadmill before making any adjustments To adjust the running bed impact reduction level follow these steps 1 Facing the side of the treadmill firmly grasp the control lever shown in Photo 7 and pull the lever outw
38. your workout you need to re enter your weight page 21 page 22 5 Stand on the running belt while keeping one hand on the handrail With your other hand press the SPEED A key until you reach a comfortable walking speed about 1 5 to 2 0 mph 6 Walk for a few minutes with both hands on the handrail to get comfortable with the treadmill Next hold the handrail with one hand and use the other hand to increase the speed to about 3 0 mph Walk at this speed for a few minutes to warm up your muscles 7 Let go of the handrail with one hand and let your arm swing naturally 8 Let go with your other hand Walk with both arms swinging naturally Keep this pace for a few minutes 9 When you feel comfortable walking you may wish to jog Hold the handrail with one hand and use the other to increase speed to 5 0 mph 10 Begin jogging with both hands on the handrails As you become more comfortable remove one hand then the other 10 When you are finished working out hold onto the handrail and press the red STOP key to come to a safe stop Moving the magnetic safety key from the ACTIVATE to the OFF position also stops the treadmill Always cool down for a few minutes before bringing the treadmill to a complete stop Remove and store the safety key to insure children or an unqualified person will not be able to activate the treadmill Specifying MPH or KPH The M9 3s Low Impact Treadmill can display speed in miles per hour mph
Download Pdf Manuals
Related Search