MTD Products Aktiengesellschaft • Saarbrücken
Contents
1. secure the support plate on the grass catcher carrier using a bolt B2 and nut C2 Figs 8 and 9 2 Now hook the pre assembled part into the mounting frame on the tractor between the 2 lugs and secure the part on the mounting frame using a bolt A2 and nut C2 Figs 10 and 11 3 Install the tube holder F by clicking it onto the tubular frame of the grass catcher bag carrier Fig 12 Note In Step 1 ensure that the edge of the tube holder is flush with the red line on the tubular frame 4 Install the cover E in the hood D 1 Push the long end of the cover all the way into the recess of the hood Fig 13 Note Ensure that the cover is situated under the guide 1 Fig 14 2 Now press the other end of the cover into the designated recess 2 in the hood Fig 14 5 Now position the hood on the mounting eyelets of the tubular frame Fig 15 6 Attach the hood with the bolt K To do this push the bolt K through the first mounting eyelet and then continue through the second mounting eyelet until the end of the bolt touches the hood Fig 17 The bolt is now secured on the hood by the two lugs Fig 17 Note To facilitate installation use the inspection opening 1 in the hood Fig 16 7 Open the hood Fig 18 8 Todo this press your right hand onto the rear right plate Step 1 and grip the middle plate with your left hand to open the hood upwards Step 2 Fig 18 9 Hook both grass catcher bags G int2. For A Growing World 1 4 L10 FORM NO 769 05342C MTD Products Aktiengesellschaft Saarbr cken Germany m2 Q English Original operating instructions Francais Notice d instructions d origine Deutsch Originalbetriebsanleitung al Installing the grass catcher Follow the safety instructions and operating instructions in the operating manual for the lawn tractor Before installing the grass catcher park the lawn tractor on a level surface apply the parking brake switch the engine off and remove the spark plug terminal Check your model number so that you know which installation steps to perform Identification of the model number You can find the rating plate under the drivers seat The fifth to seventh digits of the model number indicate the series Example Model number 13AN773G600 Series 700 Installation diagrams A The installation diagrams 1 to 26 are at the front illustrated fold out pages of the manual Installing the holder L Only required on units belonging to Series 700 Figs 1 3 1 Fit a shoulder bolt D1 and nut E1 to each of the holders F1 and G1 Fig 2 2 Now attach the pre assembled holders F1 and G1 to the tractor using the 4 screws A1 Fig 3 3 Insert the bolts B1 into the two holders and secure each b
3. e intermediate piece and align it until the lower retaining groove 1 is situated firmly in the tube holder 2 Fig 26 Note Ensure that the installation is secure and correct Close the hood on the grass catcher Inspect the installation and perform a function test Operating the grass catcher Emptying Switch off the unit Apply parking brake Open grass catcher hood and lift up Take hold of the grass catcher baskets by the grip points at the bottom of the grass catcher bags and then take out of the holders Empty grass catcher bags Hook in grass catcher bags and close the grass catcher hood again Additional information To ensure that the grass catcher functions optimally the Highlift blades optional accessories or included in product package depending on model should be installed tightening torque of the blade screw 122 Nm Only allow installation of the Hightlift blades to be carried out from specialist garage If required contact your local dealer
4. o the tube holder ensuring that the more impervious side closer meshed fabric is at the front Fig 19 Note First hook in the front side and then lower the rear side until the grass catcher bag is situated firmly in the tubular frame 10 11 12 13 14 15 16 17 18 Fit the rubber mount N2 to the mower deck connector B using the bolt H2 washer 12 and safety cotter pin J2 Fig 20 Fit the retaining bolt L2 and nut M2 to the mower deck Fig 21 Installing the mowed deck connector Figs 22 24 1 Open the impact guard on the mower deck and hold it firmly in this position Fig 22 2 Place the rear upper edge of the mower deck connector over the rear upper edge of the mower deck opening Now swivel the connector down over the mower deck opening Fig 22 Note The connector is correctly installed when the lower edge is situated over the lower edge of the mower deck opening Fig 23 Ensure that the installation is correct Hook the rubber mount into the retaining bolt on the mower deck to secure the mower deck connector on the mower deck Fig 24 Align the guide grooves 1 on the intermediate piece A with the mounting lugs 2 on the mower deck connector and push the intermediate piece all the way onto the mower deck connector Fig 25 Secure the intermediate piece on the mower deck connector using the retaining clips K2 Fig 25 Open the hood and push the pipe end section H onto th
5. olt with a cotter pin C1 Fig 2 and 3 Installing the mounting frame e 1 and 4 7 Fit the two plates L1 and K1 to the plate J1 using 4 screws H1 and 4 nuts 11 Fig 4 Note Ensure that the plates are fitted correctly 2 Now turn the pre assembled mounting frame by 180 see Fig 5 3 Fit the holder C to the pre assembled mounting frame using 4 screws D2 and 4 nuts F2 Note Ensure that correct mounting holes are used in the side retaining plates and initially tighten the nuts only hand tight as this will facilitate the subsequent installation Fig 5a for mounting on tractors belonging to the 700 Series Fig 5b for mounting on all other tractors 4 Now hook the pre assembled mounting frame into the shoulder screws on the tractor frame holder Fig 6 Note In the tractor series 700 first remove the retaining bolts B1 and cotter pins C1 from the holder Fig 3 Then re attach them after hooking in the mounting frame to secure the mounting frame to the holder as well Use mounting holes X Fig 4 for installation 5 Align the lower hole in the mounting frame with the hole in the hitching device on the tractor chassis Insert the bolt E2 through the mounting holes and secure the bolt with the cotter pin G2 Fig 7 6 Now tighten all bolts and nuts on the mounting frame Installing the grass catcher je 1 8 26 Push the support plate I into the recess on the grass catcher bag carrier J and
Download Pdf Manuals
Related Search