HYUNDAI ACCENT 2010- /ELANTRA 2012- / KIA RIO 2012
Contents
1. mmu ojdung peu o dung xXoelg d 19819 peu mmm U9910 Do not drill hole for control switch before testing the cruise system uMOJg mt 3 2 BLU YEL wire to the BLUE and the other to the RED The order does not matter CONTROL SWITCH MOUNTING 3 8 Hex Nut Lockwashers 4 7 Lever Wedges Use the lever wedges on the Control Switch at an angle template to drill a 3 8 or 9 5mm hole HYUNDAI ACCENT ELANTRA KiA Rio ELECTRONIC CRUISE CONTROL KIT TROUBLESHOOTING GREEN YELLOW BROWN RED AND BLUE BLACK WHITE YELLOW ECU Ckt 2 Res Set O ELE N DESIRED RESULTS 12V WHEN SWITCHED ON AND OV WHEN SWITCHED OFF IGNITION MUST BE GREATER THAN 10V WHILE CRANKING VEHICLE LOWEST RESISTANCE TO GROUND AND CLOSEST TO ZERO 0 OHMS AS POSSIBLE USE A VEHICLE GROUND POINT WHERE OTHER GROUND WIRES ARE CONNECTED TO SET CoAST 12V PRESS AND HOLD SET RESUME ACCEL 12V PRESS AND HOLD RESUME ON Orr 12V PRESS ON 12V 0 OHMS RESISTANCE TO GROUND GROUND ACTIVE WIRE AT SWITCH WHEN NSS CLUTCH IS DEPRESSED 12V ACTIVE WIRE AT SWITCH WHEN NSS CLUTCH IS DEPRESSED On Off NSS CLUTCH NSS CLUTCH Note All accelerator pedal voltages shown are with the pedal fully depressed with ignition power FAULT CONDITION NO POWER VOLTAGE DROP OR INTERMITTENT CONNEC2. H MORE THAN 2 0 WATTS OF POWER CAN PRODUCE ELEC TROMAGNETIC INTERFERENCE THAT COULD INTERFERE WITH THE OPERATION OF CRUISE AND THROTTLE CONTROLS RESULTING IN VEHICLE LIMP MODE USE OF CELLULAR PHONES WILL NOT INTERFERE WITH THESE CONTROLS DUE TO SENSITIVE NATURE OF SIGNALS USED FOR THIS PRODUCT ALL NON PLUG AND PLAY CONNECTIONS MUST BE SOLDERED FAILURE TO COMPLY WITH THIS REQUIREMENT WILL VOID WARRANTY Form 5381 REv A 01 16 13 HYUNDAI ACCENT ELANTRA KIA Rio ELECTRONIC CRUISE CONTROL KIT W BEFORE INSTALLATION TO MAKE THE INSTALLATION EASIER THE COMPLETE INSTALLATION INSTRUCTIONS SHOULD BE READ THROUGH BEFORE INSTALLATION IS STARTED THIS INSTALLATION INSTRUCTIONS CONTAINS INFORMATION HOW TO INSTALL THE ELECTRONIC CRUISE CONTROL WHICH IS NOT A DO IT YOURSELF JOB MODERN CARS ARE EQUIPPED WITH ELECTRONICS WHICH CAN BE COSTLY DAMAGED BY INAPPROPRIATE TREAT MENT ROSTRA PRECISION CONTROLS CAN NOT BE HELD RESPONSIBLE FOR ANY ERROR CAUSED BY WRONG INSTALLATION a STOP READ BEFORE INSTALLATION D IMPORTANT ADVISORY NOTES THAT YOU MUST FOLLOW ALWAYS DISCONNECT THE NEGATIVE CABLE FROM BATTERY BEFORE INSTALLATION ALWAYS USE THE ENCLOSED INSTALLATION INSTRUCTION FOR INSTALLING THE ELECTRONIC CRUISE CONTROL CHECK THE PART NUMBER OF THE CRUISE MODULE LABEL IS THE SAME COMPARED TO THE PART NUMBER OF THE INSTALLATION INSTRUCTIONS BE AWARE OF RADIO CODES THAT MIGHT HAVE TO BE TYPED IN FIND A LOCATION TO INSTALL THE CRU
3. HYUNDAI ACCENT 2010 ELANTRA 2012 Rio 2012 ELECTRONIC CRUISE CONTROL Kir PART NuMBER 250 9628 GENERAL APPLICABILITY RECOMMENDED TOOLS THIS CRUISE WAS TESTED AND VERIFIED ON AT MT VEHICLES PERSONAL amp VEHICLE PROTECTION SAFETY GLASSES Kit CONTENTS SERVICE PARTS ITEM DESCRIPTION PART PECIAL TOOLS 250 2854 VOLT OHM METER PEDAL INTERFACE HARNESS RIM REMOVAL TOOL PHILLIPS SCREWDRIVER HARDWARE KiT 0 WRENCH 250 3742 5MM OR 3 8 FOR SWITCH 6 1 Diaenostics Harness 250 2783 14MM WRENCH NSS CLUTCH HARNESS 250 2759 SOLDERING TOOL P _ SPECIAL CHEMICALS j o CONFLICTS NOTE LEGEND STOP DAMAGE TO VEHICLE MAY OCCUR Do NOT PROCEED UNTIL PROCESS COMPLIANCE HAS BEEN MET OPERATOR SAFETY Use CAUTION TO Avo D Risk OF INJURY CRITICAL PROCESS PROCEED WITH CAUTION TO ENSURE A QUALITY INSTALLATION THESE POINTS WILL BE AUDITED ON A COMPLETED VEHICLE INSTALLATION HARDWARE BAG CONTENTS GENERAL PROCESS THIS HIGHLIGHTS SPECIFIC PROCESSES ENSURE A QUALITY INSTALLATION THESE POINTS WILL BE AUDITED DURING ITEM DESCRIPTION THE ACCESSORY INSTALLATION 1 8 WIRE ZIP TIES TOOLS amp EQUIPMENT THIS CALLS OUT THE SPECIFIC TOOLS AND EQUIPMENT REQUIRED FOR THE PROCESS REVISION MARK THIS MARK HIGHLIGHTS A CHANGE IN INSTALLATION WITH RESPECT TO PREVIOUS ISSUE WHEN TRANSMITTING FROM INSIDE THE CAR 2 WAY RADIOS THAT OPERATE IN THE 25MHZ 700MHZ FREQUENCY RANGE WIT
4. ISE MODULE AND CONTROL SWITCH IF ANY WIRES ARE LEFT THEN CUT OFF AND INSULATE ONLY USE A MULTIMETER TO MEASURE VOLTAGE ALWAYS DRIVE THE CAR FOR A COMPLETE TEST BEFORE ASSEMBLING THE CAR ALL WIRE LEADS MUST BE SOLDERED HYUNDAI ACCENT ELANTRA KiA Rio ELECTRONIC CRUISE CONTROL KIT INSTALLATION N 10mm Wrench Negative 1 Battery O Cabl ec i Battery To OBD2 Connector Connect to the Note For vehicles with manual transmission lerat only Connect Clutch Harness to Control accelerator Module Connect Yellow Wire to the top pedal Clutch Switch connector to one of the 2 white wires HYUNDAI ACCENT ELANTRA KiA Rio ELECTRONIC CRUISE CONTROL KIT INSTALLATION 5 Ignition Kia Rio Connect the Red Ignition Hyundai Accent Connect the Red wire to orange wire between gray Ignition wire to pink wire in top left and yellow wire as shown at the corner of white connect on the left traction control connector located side of the fuse box located under behind the drivers side dash the drivers side dash 4 dm HYUNDAI ACCENT ELANTRA KiA Rio ELECTRONIC CRUISE CONTROL KIT INSTALLATION MO 9A enig MO 9A enig Switch Harness Rostra Switch BLACK muss BLUE YELLOW BLUE black connector white connector RED PURPLE GREEN BLACK PURPLE YELLOW YELLOW GREEN BROWN Both Blue Yellow wires are spliced together Just connect one
5. TION WILL CAUSE LOSS OF PEDAL OR LIMP MODE CONDITION BAD GROUND CONNECTION WILL CAUSE THE FOLLOWING CONDITIONS CRUISE WILL NOT FUNCTION LOSS OF PEDAL OR Limp MoDE CONDITION CRUISE WILL NOT SET IF THIS CONNECTION IS NOT INSTALLED CORRECTLY CRUISE WILL NOT RESUME OR ACCEL IF THIS CONNECTION IS NOT INSTALLED CORRECTLY CRUISE WILL NOT SET IF THIS CONNECTION IS NOT INSTALLED CORRECTLY CRUISE LIGHT WILL NOT COME ON IF THESE CONNECTIONS ARE NOT INSTALLED CORRECTLY CRUISE WILL NOT FUNCTION IF WRONG WIRE IS CONNECTED OR CRUISE WILL NOT DISEN GAGE WHEN CLUTCH IS DEPRESSED w Rostra x Precision Y Controls Inc
Download Pdf Manuals
Related Search