OWNER MANUAL - Spa Central
Contents
1. Backward Forward OPERATIONS amp USE 9500 9600 Shiatsu Remote Control Please refer to instruction manual for operations 60 Upper Knead Neck Back Back Waist Stretching Seat Seat Seat Seat Seat Forward Backward Incline Recline CLEANING amp MAINTENANCE Please refer the diagrams to remove jet covers for cleaning Gulfstream Plastics Ltd highly recommends the following cleaning regimen You should always contact your local governing agency for their specific cleaning and disinfecting requirements and regulations for pedicure spas For your clients safety always use the regulations as a minimum standard for cleaning and disinfecting Combining your states standards with the regimen listed below will provide your clients with a safe and healthy pedicure spa environment experience Routine maintenance Powdered cleansers or abrasives are NOT RECOMMENDED A clean towel or sponge are all that are usually needed A soft bristled brush may be used when excessive residue is present Use a mild soap and water solution to clean the upholstery but do not over wet Wipe dry with a clean towel No internal maintenance of the spa components is necessary Remove clean jet caps and spray with disinfectant after each use For extra protection our recommendation is that the system be flushed daily or weekly depending on use To flush the clean jet system fill spa with hot water to just above the jets2. or equivalent A Warning THIS PRODUCT IS FOR IN DOOR USE ONLY DISCONNECT POWER SUPPLY CORD BEFORE SERVICING AND CLEANING Foot spa must be installed by a licensed plumber and electrician in accordance with local codes Plumbing and Electrical Installation instructions must be adhered to in order for the warranty to be in effect and to insure the utmost in safety Chair and spa have a maximum seating capacity of 350 pounds If a crack occurs in the glass bowl DO NOT manually handle the bowl unless the proper attire is worn Warning Under no circumstances must the bowl be used by your customers as you can be held accountable for any injury that may occur Gulfstream Plastics is not liable for any injury that may occur BASIC PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING 1 Read and follow all instructions 2 DANGER To reduce the risk of injury do not permit children to use this unit unless they are supervised at all times Use this unit only for its intended use as described in this manual Do not use attachments that are not Recommended by the manufacturer Never drop or insert any object into any opening Do not block jets during whirlpool operation The unit must be connected to an electrical supply circuit that is protected by a ground fault circuit interrupter The clean jet motor is magnetically driven and is insulated twice Therefore it does not require to be bonded Save these instructions 1 Excessive wate
3. Add disinfectant Run whirlpool for 15 minutes drain and then wipe dry with clean soft cloth NOTE Cleaning or sanitizing is NOT disinfecting According to the Centers for Disease Control and Prevention CDC and the US Environmental Protection Agency EPA disinfecting occurs only when there is a reduction of pathogenic microbes at 99 999 Sanitizing is only a reduction of 99 9 Cleaning of whirlpool pedicure spas requires surfactant and chelating detergents that are low foaming and have the ability to remove body oils organic oil additives mineral oil skin cells nail clippings etc that can accumulate both in the basin and the jets which may become a fertile area for micro organisms to grow sf The use of oil based products can build up in the whirlpool system causing clogging in the jets Adherence to the above cleaning will minimize build up Gulfstream Plastics Ltd does not recommend the use of mineral oil based products TESTING FLUSHING FOOT SPA After foot spa has been installed fill tub with water just above the jets Carefully check for leaks at drain and over flow After checking underside for leaks turn on system by pushing whirlpool button and watch for leaks as water circulates Let tub run full cycle Open drain plug for water discharge WARRANTY amp SERVICE D Gulfstream warrants to the original purchaser that the new pedicure spa will be free from defect during the Standard Warranty Period li
4. Cap Head counter clockwise to remove carefully pull the metal claim and the jet motor backward There may be water sealant between the Motor and Tub wall To assemble the jet unit install in the reverse steps above You may have to apply some water sealant between the Motor and The Tub wall Under Seat Compartment Plate located inside the bowl Jet Cover amp Impeller Cleanjet Max only Jet Handle Cleanjet Max SL only INSTALLATIONS D Plumbing Connections Gravity Drain Power Drain Hot amp Cold 72 Fitting 1 1 4 ABS Pipe E 3 4 Fittin Not provided Drain Pump 2 1 Discharge pump may be connected to an existing sink drain or floor drain It can also pump up to 7 ft high but this will increase the length of the drain time The drain connection is at the rear of the unit by a 3 4 fitting 2 Gravity drain uses a standard gravity drain A floor drain is recommended Connection via a P Trap is supplied 3 Hot and cold water supply connections are located at the rear of the unit 7 fittings Please be advised that the hot and cold water supply lines are not fitted with optional back flow Preventers unless ordered at initial sale 4 Have a qualified licensed electrician to install the wiring according to local codes The Cleanjets are 1 10 hp 120V 1 2 AMP 60OHZ A 15 amp GFI protected circuit must be used to supply power to the unit The roller back massage chair uses a 115V supply 5
5. OWNER MANUAL FOR FUTURE REFERENCE fe Few i FOOT SPA Chair 9700 M ED CE 2009 All rights reserved Design and Specifications are subject to change without notice Table of Contents Owner Manual Safety and Precautions Susan Bee SoG ms des ARRERA TANIA Ge seu nn RR Re side de ela haw 1 2 Identifying Parts EEE 3 4 Foot spa Clearance CREM ENE D 6 o ne 6 oo es ER RE RE Re 5 INSTALLATIONS Attaching Seat EEE 6 Jet Assembly A tenses 7 9 Plumbing Connections a TT 10 Operations and Use ERRET CAR RE Tee ORR RES SR AN TARR ERE RR TS SELLES 11 13 Cleaning amp Maintenance rissa 14 Warranty amp Service SAFETY amp PRECAUTION Thank you for purchasing the La Fleur spa from Gulfstream Plastics Ltd Please carefully read instructions before installing the spa Carefully follow the instructions your spa will give you years of beauty and service This product is to be connected to a branch circuit outlet protected by a Class AGROUND FAULT CIRCUIT INTERRUPTER GFCI and the GFCI shall be tested regularly for continued protection and correct operation If a Class A GFCI protected outlet is not available DO NOT USE THIS PRODUCT Please contact a licensed electrician for installation of a Class A GFCI according to local electric codes
6. Spa base should be anchored securely to the floor The base may be anchored through the opening in the back of the base wherever access is convenient for the installer FAILURE TO ANCHOR THE BASE MAY RESULT IN PERSONAL INJURY OR DAMAGE TO THE UNIT DAMAGE AS A RESULT WILL VOID THE WARRANTY OPERATIONS amp USE Control Panel Water Control Jet On Off Hand Spray Drain Control 1 To fill water The foot spa is provided with a single hot and cold mixing valve located on the front of your spa far left This is a pressure balance valve that requires you to lift the handle to start the water flow and to adjust to the temperature that is desired The clean jet motor must be completely submerged in water CAUTION DO NOT USE FOAMING SUDSING OR MINERAL OIL BASED ADDITIVES IN THE WATER 2 To start whirlpool Press the button that is situated next to the water fill lever This will start your Clean Jet motor You may stop the whirlpool function at any time by pressing the button again 3 The foot spa is equipped with a hand held sprayer To activate the hand shower pull the hand shower from the receptacle and depress the thumb control on the sprayer handle This will turn on the water When you release pressure on the thumb control this will turn the water off 4 To drain whirlpool tub The spa is equipped with a built in optional discharge pump Open the drain plug by turning the control knob with which is situated at the far right of
7. ce of Proper water are not covered by this warranty Staining fading or discoloration of the seat armrests or footrests Freight damage misuse neglect accident natural disaster and abuse Unauthorized repairs i pur Service gt 1 The Dealer shall forward all warranty related matters to our Customer Service Department Serial Numbers and Original Invoice must accompany all warranty claims Customers are responsible for shipping defective parts back to Gulfstream These parts must be packaged correctly in order to protect against any further damage All parts are to be shipped by UPS Ground Service average 2 5 days All defective parts must be shipped back to Gulfstream within 30 days of receiving the new replacement parts or warranty will be void Any warranty claim that cannot be determined over the phone the customer must send photos and original invoice directly to Gulfstream before any repairs can be performed Any service performed on the product without Gulfstreams authorization will also void the Warranty Each service call from the customer will be assigned a Claim Number The Claim Number will stay open until the problem is resolved QS O O1 BR w N CON No dealer or other person has any authority to bind Gulfstream Plastics Ltd to changes or additions to this warranty or its products Accordingly Gulfstream Plastics Ltd is not responsible for such warranties or represen
8. ection to remove jet cover to install jet cover Cleanjet Max Components Plate amp Anchors Cleanjet Max only Suction Control Screen Optional Jet Cover Impeller Jet Motor amp Housing INSTALLATIONS Cleanjet Max Installation Jet Cover and Impeller Anchor Snap the jet cover and impeller onto the anchors located on the plate in the direction of arrow as shown Make sure the jet snapped securely on the plate To remove simply pull the jet cover and impeller from the anchors Cleanjet Max SL Installation Tb Wall Fa Opening Jet Place the poly liner and drain plug firmly onto the tub hold the handle and push into the opening located under the footrest in the direction of the arrow until it is secured Make certain that the jet is snapped firmly on the tub wall and the handle is secured to the opening To remove simply pull out the handle with jet cover and impeller from the opening Pull out the lock as shown to remove cover and impeller from the handle INSTALLATIONS A Warning Some jet components are located under the base unit behind the tub wall Cleanjet Max Assembly Disconnect the foot spa unit from any electrical source before disassemble the jet unit All surface must be dry Some jet components may contain sharp object and very hot after usage To remove the jet unit follow the steps below Carefully detach the Jet Cover and Impeller from Tub Wall O Turn the
9. ng plug and a three blade grounding plug and a three slot receptacle that will accept the plug on the appliance Replace or repair a damaged cord COMPLIANCE WITH LOCAL CODES OR INSPECTIONS IS THE RESPONSIBILITY OF CROUNDINGEEIN THE PURCHASER AND OR INSTALLER GROUND FAULT INTERRUPTER OUTLET NEMA 5 15R NOT INCLUDED WITH MIRAGE OPERATION AND USE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS 1 IMPORTANT At the end of the day ALWAYS turn the main power OFF DANGER To reduce the risk of injury do not permit children to use this unit unless they are closely supervised at all times 3 CAUTION This unit should not be used by persons with open wounds cuts or sores on their feet or legs or by persons with poor circulation or by persons with heart conditions If in doubt the client should consult with his or her physician 4 Use this unit only for its intended use as described in this manual Do not use attachments not recommended by the manufacturer 5 Do no operate with a damaged cord or plug If the Mirage Pedicare System malfunctions or is damaged in any manner contact an authorized service representative for examination or repair 6 Never drop or insert any objects into any opening 7 Do not operate this unit without the guard screen over the suction fitting located in the bottom of the enameled bowl 8 Do not block jets during pedicure operation 9 Water temperature should be checked before use Water temperature sh
10. ould never exceed 104 degrees Fahrenheit 10 Never bring any electrical devices into the pedicure or operate electrical devices near it 11 The unit must be connected to a supply circuit that is protected by a ground fault circuit interrupter GFCI 12 Connect the Mirage pedicure only to a properly grounded outlet See grounding instructions 13 Close supervision is necessary when the Mirage Pedicare System is used by on or near children or invalids O IDENTIFY YOUR FOOT SPA oO O O1 N gt ma 15 Jet Drain Water Control Jet Control Hand Spray Glass Bowl Water Filler Back Cushion amp Massage Headrest Pillow Control Panel Wooden Armrest Flip out Manicure Tray Seat Cushion Adjustable Footrest Front Control Panel Drain Control IDENTIFY YOUR FOOT SPA SEAT OPERATION SPA DIMENSION FOOT SPA CLEARANCE WALL CLEARANCE Foot spa 1 Clearance INSTALLATIONS Attaching The Seat to The Base Attach trays or remote stand to armrest with screws provided Align the seat with the pre drilled holes on the base then tightly secure with the nuts and bolts provided INSTALLATIONS Cleanjet Installation The Opening Align fingers to the opening turn counter clockwise Align jet cover on the jet housing then turn clockwise and pull in the arrow dir
11. r temperature is dangerous and should be checked BEFORE use 2 Maximum temperature of the water should never exceed 100 degrees F 3 Always enter and exit the Foot Spa slowly and carefully 4 NEVER bring and or operate any electrical devices into or near the Foot Spa SAFETY amp PRECAUTION GROUNDING METHODS Because this unit must be connected to a circuit with a ground fault circuit interrupter GFCI DO NOT use a grounding adapter The use of a grounding adapter is prohibited in Canada by Part of the Canadian Electrical Code GROUNDING INSTRUCTIONS This appliance must be plugged into an outlet equipped with a ground fault circuit interrupter The ground fault interrupter can be in the out let shown in illustration A or in the circuit breaker fuse box If your outlet or circuit breaker fuse box is not equipped with a ground fault interrupter you must have your electrician install one In the event of an electrical short circuit the ground fault circuit interrupter will turn off the electrical power to the unit immediately greatly reducing the likelihood of serious injury This appliance is for use with a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated in sketch B The outlet must be properly installed and grounded in compliance with all local codes and ordinances If it is necessary to use an extension cord use only a three wire extension cord that has a three blade groundi
12. sted below The shipping date and the uniquely coded Serial Number on the back of each spa chair will justify the start of the warranty period for the product The warranty is null and void if the pedicure spa is taken from its initial place of installation or it is not installed in accordance with federal state or local codes and ordinances Also this warranty does no apply if the pedicure spa has been subject to misapplication improper installation or maintenance negligence improper cleaning or other circumstances beyond Gulfstream s control Warranty TN Limited Three 3 Years warranty on Spa Shell Limited One 1 Year warranty on the Whirlpool Pump Limited One 1 Year warranty on the Clean Jet Limited One 1 Year warranty on the Glass Bowl Limited One 1 Year Parts Only warranty which covers the Hydraulic System Discharge Pump Massage System and All Electrical Components RON 6 Gulfstream will pay shipping charges on all replacement parts during the first 90 days of the stated Warranty Period After 90 days the consumer is responsible for all labor and shipping costs incurred ja Exclusions a gt 1 Damage to pump parts and or motor parts due to obstruction in plumbing lines etc 2 Staining fading or discoloration of plastic surfaces due to exposure and or the use of harmful cleaning agents or Chemicals Staining fading or discoloration caused by improper or poor water additives not related to the maintenan
13. tations Manufacturer of Acrylic Bath Whirlpool amp Pedicure Foot Spas Gulfstream Plastics Ltd Cambridge Ontario Canada N1R 6T4 Tel 519 622 0950 Fax 519 622 6926 www gulfstreamplastics com 2009 All rights reserved Design and Specifications are subject to change without notice
14. the spa base Press discharge pump timer button situated far left on front of base pump will run for approx 2 min Average time for drain 1 minute 5 9600 amp 9700 chairs Shiatsu Roller back massage is equipped with a state of the art massage system The massage system is easy to use the remote has a one touch power that starts select your own massage You can also adjust the front to rear position of the chair and the reclining back By using the remote your client can adjust the back to the most comfortable position BASIC PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING 1 Read and follow all instructions 2 DANGER To reduce the risk of injury do not permit children to use this unit unless they are supervised at all times Use this unit only for its intended use as described in this manual Do not use attachments that are not Recommended by the manufacturer Never drop or insert any object into any opening Do not block jets during whirlpool operation The unit must be connected to an electrical supply circuit that is protected by a ground fault circuit interrupter The clean jet motor is magnetically driven and is insulated twice Therefore it does not require to be bonded Save these instructions OPERATIONS amp USE 9700 Shiatsu Remote Control Please refer to instruction manual for operations Neck Shoulder Back Waist Pause rears Air On Off Width Intensity Incline
Download Pdf Manuals
Related Search