MPS 409 Setup Guide - Extron Electronics
Contents
1. DVI output HDMI output and video output unbalanced from the switcher to the appropriate display inputs c For stereo input connect up to nine audio sources to each of the unbalanced stereo audio input groups VGA YUV DVI HDMI and Video See the 3 5 mm plug A CAUTION ds Seis connector diagram on the right for wiring sleeve s to the ground contact DO NOT connect the sleeve s to the d For unbalanced stereo output connect an output device to each of the negative contacts output groups VGA YUV DVI HDMI and Video See the 3 5 mm plug connector diagram on the right for wiring sett M No Grin ra pains e Connect an audio amplifier to the Program Audio Output connectors Ring No Ground Here 2 See the connector diagram on the right for proper wiring Balanced Output Unbalanced Output f Optional Connect a microphone to the rear Mic Line connector see the figure at right Refer to the microphone user guide for GONE ki i i leeve A OL oe roper wiring and phantom power requirements LEVEL prop g p p q hip coy Unbalanced Mic Input Set switch 2 of the DIP switch bank down off for a microphone If core moune dhe me i i i aiee a Zez 0 Tx Rx phantom power 48V is required set switch 1 up on AARAA fT F are g Optional If the switcher is connected to a computer or host Sleeve LO s controller for remote control connect the host RS 232. 81 3 3511 7655 400 833 1568 971 4 2991800 Inside USA Canada Only Inside USA Canada Only Inside Europe Only Inside Asia Only 81 3 3511 7656 FAX Inside China Only 971 4 2991880 FAX 1 714 491 1500 1 919 863 1794 31 33 453 4040 65 6383 4400 86 21 3760 1568 68 1833 50 1 714 491 1517 FAX 1 919 863 1797 FAX 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1566 FAX Rev A 07 10 2010 Extron Electronics All Rights Reserved WWw extron com 4
3. DVI HDMI In the example below HDMI input 2 is selected Only the HDMI output is active A A HDMI audio indicated by the flashing LED is routed to both the group output and _ _ _ _________ Program Audio Output Press and Hold Press and release for three seconds Single Mode VGA YUV INPUTS DVI INPUTS HDMI INPUTS VIDEO INPUTS 1 2 II 1 2 I 2 1 2 3 lf 1 E Eo me Bo Ho Ho MODE SINGLE SEPARATE COMBINE DV HDMI Single Switcher Mode Separate Switcher Mode Separate switcher mode allows the four groups of inputs DVI HDMI VGA and composite video to be used individually Each group has an independent output creating four independent switchers Up to four inputs can be selected at one time one in each group indicated by four lit LEDs The audio and video of the selected input group outputs only on the associated group output Audio from the last input selection also goes to the Program Audio Output Of the four selected inputs the audio input routed to the Program Audio Output is indicated by the blinking input LED To enable separate switcher mode eee Press and hold the Mode button VGA YUV Input 1 for three seconds then press and release the Separate DVI input 1 button The associated LED indicates if Gs es ae aes 7 separate switcher mode is on when lit or off When the Mode button is released Ua mo the LED resumes input indication MODE INGLE
4. LEDs off Rotate the Program Audio volume knob clockwise to increase and counterclockwise to decrease the audio level The front panel LEDs display the level setting as the knob is adjusted see Audio Gain Attenuation Adjustments in the MPS 409 User Guide 4 Once the desired level is achieved to adjust another input select it within three seconds If audio adjustments are complete to exit the gain attenuation mode a Do not press any front panel buttons for at least three seconds or b Press the Program Audio Mute and MIC Mute buttons At any time during the adjustments if the front panel buttons are not pressed or the program knob is not rotated within three seconds the switcher times out and the gain attenuation mode is exited Setting the Program Output Audio Level 1 Turn on all equipment and select an input with an audio signal present PROGRAM AUDIO 2 Turn on program audio by pressing the Program Audio Mute button the LED MUTE m IN a goes out mo z 3 Using the Program Audio volume control right adjust the volume of the audio amplifier connected to the Program Audio Out connector to achieve MPS 409 the desired sound level DIGITAL MEDIA PRESENTATION SWITCHER Setting the Microphone Level 1 Turn on all equipment and select an input with an audio signal present 2 Ifthe program audio output level has not been adjusted do so before setting MIC the microphone level MUTE 3 If phantom power is required
5. SEPARATE COMBINE DVI HDMI In the example below VGA YUV input 2 DVI input 1 HDMI input 3 and p Video input 2 are selected All four group outputs are active with their respective 4 a i Press and Hold Press and release AV input signals on them The audio of DVI input 1 is also routed to the Program forthrae seconds Separate Mode Audio Output indicated by the flashing LED lt a INPUTS DVI INPUTS HDMI INPUTS VIDEO INPUTS gt Mo me NO ss so ss MODE SINGLE SEPARATE COMBINE DVVHDMI Separate Switcher Mode Combined HDMI DVI Mode Combined mode allows the MPS 409 to function as a 5x1 HDMI DVI switcher This is accomplished by switching a selected DVI or HDMI input to the HDMI video output deactivating the video output In single combine mode the front panel input selection LEDs operate the same as when in single switcher mode a single lit LED indicates the current input selection MPS 409 Setup Guide Continued In separate combine mode only one input selection is allowed from the HDMI DVI groups along with a single input selection from the VGA YUV group and another from the Video group So there will only be three front panel input LEDs lit in combined mode rather than four when in separate switcher mode Combined Switcher Mode To enable combined switcher mode ee hens a a Press and hold the Mode button VGA YUV Input 1 for three seconds then Eo Ee Eo me mo press and release the Co
6. for the microphone be certain it is on Ke 4 Turn on the microphone by pressing the MIC Mute button the LED goes out 5 Talk into the microphone in a normal voice and adjust the Mic volume knob right to the desired sound level T MPS 409 Setup Guide Continued Setting the Microphone Talk Over Threshold Microphone threshold the volume where vocal audio is detected and the program audio level during talkover are adjustable via SIS commands See Audio Adjustments in the MPS 409 User Guide for additional SIS commands 1 Speak into the microphone in a normal voice The main program audio level should drop moderately If not adjust the microphone threshold level 2 Stop speaking into the microphone Main program audio should recover to its previous level after approximately four seconds If not adjust the microphone threshold level 3 If the program audio during talkover is too loud or too soft adjust the program audio level Mic talk over threshold Display talk over threshold 2 Thr lt Shows the mic threshold number x8 0 through 15 default 8 Decrement threshold 2 Thr lt 1 Decrements mic threshold one step Increment threshold 2 Thr lt Increments mic threshold one step View mic talk threshold 2 Extron USA West Extron USA East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters 800 633 9876 800 633 9876 800 3987 6673 800 7339 8766
7. 2 cable to the Balanced Mic Input 3 pin captive screw connector on the rear of the switcher see the figure at right 3 6 Gm RS 292 Device eae Bidirectional Do not tin Transmit Tx gt Transmit Tx the wires Receive Rx ea Receive Rx Ground Ground MPS 409 Setup Guide Continued Setup and Operation Video Switching The MPS switcher can be connected to as many as nine input devices simultaneously and operate in one of four switching modes single the default separate single combined or separate combined To view the current mode press and hold the Mode button VGAVYUV input 1 The associated mode LEDs single separate single combined or separate combined will light Single Switcher Mode Single switcher mode emulates one switcher with 9 inputs 9x1 Only one input can be selected at a time indicated by a single lit LED on the front panel input selections The selected video input will output on the associated group output only while the audio is output on the group output and Program Audio Output To enable single switcher mode Press and hold the Mode button VGA YUV Input 1 for three seconds then press and release the Single button VGA YUV Input 2 The associated LED indicates if single switcher mode is on when lit or off When the Mode button is released ail A 1 the LED resumes input indication Single Switcher Mode MODE SINGLE SEPARATE COMBINE
8. MPS 409 Setup Guide This guide provides basic instructions for an experienced technician to install set up and operate the Extron Media Presentation Switcher MPS 409 Where possible in the following pages line drawings are used to clarify steps discussed in the text Installation and service must be performed by authorized personnel only Installation Step 1 Disconnect Power Remove power from the switcher and all other devices that will be connected PROGRAM AUDIO VIDEO INPUTS f f J exec 1 2 e e mo Me He mie MODE SEPARATE a MODE CONFIG MPS 409 DIGITAL MEDIA PRESENTATION SWITCHER Step 2 Mount the Switcher The MPS 409 is housed in a full rack width 8 5 inch deep 1U high metal enclosure Select a mounting location then choose an appropriate mounting option and mount the switcher 100 240V 0 4A MAX OUTPUT 2 OUTPUT Ce E Ee 1 OUTPUT HEE O SETTER azo GN o Fk Je ol s o v Step 3 Cable the Switcher Tip L Make certain the MPS 409 all sources and displays are powered off Run all audio video Re communication and power cables for operation aoe a Attach up to two VGA YUV two DVI three HDMI and two composite video input devices to the switcher leeve 3 5 mm Stereo Plug Connector b Connect the VGA YUV output
9. mbine DVI HDMI button DVI input 2 The Combine sy MMM DVI HDMI button LED indicates if combined switcher mode is on when lit or off The Single and Separate button LEDs indicates whether it is in single Press and Hold Press and release switcher mode or separate switcher mode When the Mode button is released for three seconds Combine DVI HDME the LED resumes input indication Setup and Operation Optimizing the Audio For optimal audio quality the audio input levels can be adjusted individually In addition the microphone and program output levels can be adjusted separately using the front panel controls Program output and microphone levels are independent from each other Muting program audio does not mute the microphone input Setting the Input Audio Level 1 Simultaneously press and hold the Program Audio Mute and MIC Mute Press and hold buttons until the two mute LEDs flash three times then release both for seconds buttons 4 mic PROGRAM AUDIO VIDEO INPUTS A 2 Press a Video Input button for the audio to be adjusted video input 1 a fs al MUTE Mure is shown If an input button is not pressed the switcher times out and o me Mo me oO me exits audio level adjustment mode 4 Press input to Adjust input select level 3 In audio adjustment mode when an input button is pressed the front panel input LEDs indicate the current gain attenuation setting Factory default is O dB all
Download Pdf Manuals
Related Search