MTP 1500RL 15HD A SEQ • Setup Guide
Contents
1. A SEQ Flat Panel Display Extron MTP 1500RL 15HD A SEQ Flat Panel Display 1 3 5m T able Figure 1 Example of a typical MTP 1500RL 15HD A SEQ application 68 1554 50 Extron USA Headquarters 1 800 633 9876 USA Canada Only Extron USA West 1 714 491 1500 FAX 1 714 491 1517 Extron USA East 1 919 850 1000 FAX 1 919 850 1001 Rew B 2013 Extron Electronics All rights reserved All trademarks mentioned are the property of their respective owners WWW extron com aie2. ct So As y Ja N S 9 be urio MTP 1500RL 15HD A SEQ e Setup Guide Extron Electronics INTERFACING SWITCHING AND CONTROL This guide provides basic instructions for an experienced installer to set up and operate the Extron MTP 1500RL 15HD A SEQ twisted pair receiver For full details see the MTP 1500RL 15HD A SEQ User Guide available online at www extron com xt Extron C RED SELECT GREEN COBLUE DELAY LEVEL Q A PEAKING ADJUST INPUT BUFFERED OUTPUT OUTPUT Installation and Setup Step 1 Mounting MTP 1500RL Series MTP 1500RL 15HD A SEQ Turn off or disconnect all equipment power sources Mount the MTP 1500RL 15HD A SEQ receiver as required Step 2 Connect Input Connect the RJ 45 cable from an MTP transmitter to the Input port on the MTP 1 500RL 15HD A SEQ receiver Terminate the cable as shown below right using the same standard A or B at both ends Transmission distance with one device before the MTP 1S00RL 15H00 AS SEQ MTP 7S00RL 1SHD AS Device b 1000 feet 305 m maximum AS 232 data signals Transmission distance with more than one device before tha MTP 7S500RL 15HD RS SEQ 1500 feet 457 m maximum video signals ___ MTP RL Rx Device 1000 feet 305 m maximum AS 232 data signals MTP 1500RL 15HD RS Device NOTE The transmitter and receiver are designed for and perform best with Color Col
3. d V sync V switches Set these switches up On for positive sync or down Off for negative sync H V LCI cSYNC SPARE LCI LO LECI SOG LC VIDEO LCI END LC Composite Sync SOG and Video switches Set these switches as shown in the table on the right to output the indicated format e End Unit switch Set this switch up if either of the following is true e The receiver being configured is the only receiver connected to the transmitter e The receiver being configured is the last receiver in a daisy chained system Step 5 Power Wire the 2 pole captive screw connectors for the included external 12 VDC power supplies see image on the right Plug them into all units Grounding guidelines Extron MTP 1500RL 15HD A SEQ products can be adversely affected by electrostatic discharge ESD if they are not grounded correctly SECTION A A Power Supply To prevent malfunctions or product damage an experienced installer can correctly ground an Extron Output Cord MTP 1500RL 15HD A SEQ product in either of two ways e Ground the power input port Insert one end of the grounding wire to the negative or ground pin on the power input connector see image on the right Tie the other end of the wire to an earth ground e Ground the chassis Use a connector hex nut see image on the right Tie the other end of the wire to an earth ground If you have any questions about how to ground a p
4. or RJ 45 Connector 1 2345678 White green l White blue White blue Insert Twisted 7 White brown White brown Pair Wires Brown Brown Extron Enhanced Skew Free AV cable terminated in accordance with the TIA EIA T568A standard CAT 5 cables are acceptable but less preferable Using preterminated and tested cables is also recommend Cables terminated on site should be tested before use to ensure that they comply with Category 5 specifications Step 3 Connect Outputs Attach the applicable output cables video audio and buffered output A High resolution video output Connect a display device to the 15 pin HD connector RGB B Audio connector Connect an audio device to the 5 pole captive screw c onnector for mono audio output n Mono output 1 L z Mono output 1 M qy O z 16 MAX NO GROUND z 2 Mono output 1 2 5 mm Sleeve s mmm gt Sleeve S i gt S Mono output 2 E We g Mono output 2 SS as NoGROUND A p 3 Mono output 2 LAE Of 4 Unbalanced Output Balanced Output Do not tin the wires A A CAUTION For unbalanced audio connect the sleeve s to the ground DO NOT connect the sleeves to the negative contacts contact C Buffered output Connect up to 5 daisy chained MTP receivers to this RJ 45 connector a MTP 1500RL 15HD A SEQ e Setup Guide Continued Step 4 Receiver DIP Switches e H sync H an
5. roduct in a specific application contact an Extron technical support specialist Step 6 Peaking and Level Adjust image sharpness with the Peaking control Increased peaking compensates for mid and high frequency detail LEVEL PEAKING loss The LED lights red when minimum zero and maximum peaking is reached Adjust image brightness using the Level control View the image and adjust either control for the best image quality ne MIN MAX Step 7 Skew Compensation Pair skew can be measured with test equipment or by viewing a crosshatch test pattern The SEQ receivers have built in skew compensation capabilities Adjust the equalization as follows C RED SELECT GREEN I COBLUE DELAY A Set the skew delay to zero for red green and blue by pressing and holding the Select button in for 3 seconds using a Tweeker or small screwdriver When the Red Green and Blue LEDs all go out release the Select button B Use UTP cable test equipment or examine the displayed image to determine which video signal red green or blue is shifted furthest to the right C Adjust the furthest left video signal by using a Tweeker or screwdriver to press and release the Select button until the LED for the left shifted color lights D Slowly rotate the Adjust control clockwise until the shifted color is properly aligned E Repeat steps C and D to align the third color if needed Extron MTP 1500RL 15HD
Download Pdf Manuals
Related Search